Download Flux 415

Material Safety Data Sheet
#415 Flux-All Purpose Liquid Soldering Flux
Section 1: Product Information
Supplier’s Name
Manufacturer’s Name
Refer to supplier
Address
Address
Refer to supplier
2300 Winston Park Dr
Oakville, ON L6H 7T7
Telephone Number
Telephone Number
(905) 829-8780
1-800-268-4833
Chemtrec (24 hour)
1-800-424-9300
Trade Name
N/A
Chemical Formula:
N/A
Product Use
Brazing
Section 2: Hazardous Ingredients
Hazardous Ingredient
Approximate
Concentration %
Hydrochloric Acid
Zinc Chloride
Ammonium Chloride
Methyl Alcohol
1
2
3
4
5.6
34.0
9.5
1.5
CAS Number
7647-01-0
7646-85-7
12125—02-9
6-7561
LC50
LD50
OSHA
PEL
1-see below
2
3
4
N/A
N/A
N/A
N/A
LC50 (inhalation- rat) 4701 ppm for 30 minutes
LD50 (oral-rat) 350 mg/kg
LD50 (oral-rat) 1650 mg/kg
LD50 (scu-mus) 9800mg/kg
Page 1 of 4
81962349
Section 3: Physical Data
Physical State: Liquid
Odour and Appearance: Clear. Acrid.
Odour Threshold(PPM): N/A
Specific Gravity: 1.354
Vapour Pressure(MM): N/A
Vapour Density (Air =1): N/A
Evaporation Rate: <1
Boiling Point: 120-157ºC
Freezing Point: N/A
Solubility in Water(20): Infinite
% Volatile (by Volume): 50%
pH: 1.5
Coefficient of Water/Oil Distribution: N/A
Section 4: Fire or Explosion Hazard
Flammable: No
Means of Extinction: N/A
Special Firefighting Procedures: N/A
Flashpoint:
N/A
Upper Flammable Limit (% by volume): N/A
Lower Flammable Limit (% by volume): N/A
Auto ignition temperature:
N/A
Hazardous Combustion Products:
May release chloride gas in a fire.
Explosion data-sensitivity to mechanical impact: N/A
Explosion data-sensitivity to static discharge:
N/A
Section 5: Reactivity Data
Chemical Stability: Yes
Incompatibility to other substances: Yes
If so, which ones?
Cyanides (may release toxic HCN gas) and
Sulfide Salts (may release toxic H2S gas)
Reactivity under what conditions? May react at high temperatures
Hazardous decomposition products: N/A
Section 6: Toxicological Information
Corrosive Product
Skin Contact:
Skin Absorption:
Eye Contact:
Inhalation:
Ingestion:
May cause burning and severe irritation.
Will not be absorbed by the skin.
Severe burning. Blurring of vision
Nose, throat, and lung irritation effects with cough, discomfort
and shortness of breath.
Causes severe burns to mouth, tongue, throat and stomach
Page 2 of 4
81962349
Exposure Limits
Irritancy of Material
Sensitization to Material
Carcinogenity
1 mg/m3
as fume
N/A
N/A
No
Reproductive Toxicity
N/A
Teratogenicity
Mutagenicity
Toxicologically synergistic products
N/A
N/A
N/A
Section 7: Preventive Measures
Personal Protective Equipment:
Protective Gloves: Rubber, asbestos or neoprene gloves.
Eye Protection:
Safety chemical glasses and/or face shield
Respiratory Protection: If work station is not ventilated, wear NIOSH approved
mask.
Other: N/A
Engineering Controls: Good ventilation should be provided to keep fumes below
exposure limits.
Leak or Spill Procedure:
Was area with soap and water. Rinse and dry.
Handling Procedures and Equipment: N/A
Waste Disposal: Dispose of in accordance with local, provincial and federal
regulations.
Storage Requirements: Store material in a cool, dry area away from excessive heat
or cold. Rotate Stock.
Special Shipping Information: Class 8. PIN 1760, Group II.
Section 8: First Aid Measures
Eyes: Flush immediately with water for at least 15 minutes to remove all residue.
Get medical attention.
Skin: Promptly wash with soap and water to remove all residue. In the event of
irritation, consult a physician.
Inhalation:
Remove to fresh air immediately
Page 3 of 4
81962349
Section 9: Preparation Information
Prepared by:
Techniweld
(905) 829-8780
1-800-268-4833
Date Prepared:
January 1, 2009
The manufacturer believes this data to be accurate and to reflect qualified expert opinion
regarding current research. However, the manufacturer cannot make any express or
implied warranty as to this information
Page 4 of 4
81962349