Download G8052 Application Guide for Lenovo Networking

Lenovo RackSwitch G8052
Application Guide
For Lenovo Enterprise Network Operating System 8.4
Note: Before using this information and the product it supports, read the general information in the Safety information and Environmental Notices and User Guide documents on the Lenovo Documentation CD and the Warranty Information document that comes with the product.
First Edition (September 2016)
© Copyright Lenovo 2016
Portions © Copyright IBM Corporation 2014.
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS‐35F‐05925.
Lenovo and the Lenovo logo are trademarks of Lenovo in the United States, other countries, or both.
Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Who Should Use This Guide . . . . . . . . . . . . . . . . . . . . . . .22
What You’ll Find in This Guide . . . . . . . . . . . . . . . . . . . . . .23
Additional References . . . . . . . . . . . . . . . . . . . . . . . . . .27
Typographic Conventions . . . . . . . . . . . . . . . . . . . . . . . .28
Part 1: Getting Started . . . . . . . . . . . . . . . . . . . . . . 29
Chapter 1. Switch Administration . . . . . . . . . . . . . . . . . 31
Administration Interfaces . . . . . . . . . . . . . . . . . . . . . . . .32
Command Line Interface . . . . . . . . . . . . . . . . . . . . . . .32
Establishing a Connection . . . . . . . . . . . . . . . . . . . . . . . .33
Using Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Using Secure Shell. . . . . . . . . . . . . . . . . . . . . . . . . .35
Using SSH with Password Authentication . . . . . . . . . . . . .35
Using SSH with Public Key Authentication . . . . . . . . . . . . .36
Using a Web Browser . . . . . . . . . . . . . . . . . . . . . . . .37
Configuring HTTP Access to the BBI . . . . . . . . . . . . . . . .37
Configuring HTTPS Access to the BBI . . . . . . . . . . . . . . .37
Browser‐Based Interface Summary. . . . . . . . . . . . . . . . .38
Using Simple Network Management Protocol. . . . . . . . . . . . . .39
BOOTP/DHCP Client IP Address Services . . . . . . . . . . . . . . . . .40
DHCP Host Name Configuration . . . . . . . . . . . . . . . . . . .40
DHCP SYSLOG Server. . . . . . . . . . . . . . . . . . . . . . . .41
Global BOOTP Relay Agent Configuration . . . . . . . . . . . . . . .41
Domain‐Specific BOOTP Relay Agent Configuration. . . . . . . . . . .42
DHCP Option 82 . . . . . . . . . . . . . . . . . . . . . . . . . .42
DHCP Snooping . . . . . . . . . . . . . . . . . . . . . . . . . .42
Easy Connect Wizard . . . . . . . . . . . . . . . . . . . . . . . . . .44
Configuring the Easy Connect Wizard . . . . . . . . . . . . . . . . .44
Basic System Mode Configuration Example . . . . . . . . . . . . .45
Transparent Mode Configuration Example . . . . . . . . . . . . .45
Redundant Mode Configuration Example . . . . . . . . . . . . .46
Switch Login Levels . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Setup vs. the Command Line . . . . . . . . . . . . . . . . . . . . . . .50
Idle Disconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Boot Strict Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Acceptable Cipher Suites . . . . . . . . . . . . . . . . . . . . . . .55
Configuring Strict Mode . . . . . . . . . . . . . . . . . . . . . . .56
Configuring No‐Prompt Mode . . . . . . . . . . . . . . . . . . . .56
SSL/TLS Version Limitation . . . . . . . . . . . . . . . . . . . . .56
Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Chapter 2. Initial Setup . . . . . . . . . . . . . . . . . . . . . . 59
Information Needed for Setup . . . . . . . . . . . . . . . . . . . . . .60
Default Setup Options . . . . . . . . . . . . . . . . . . . . . . . . . .61
Setting the Management Interface Default IP Address . . . . . . . . . . . .62
© Copyright Lenovo 2016
3
Stopping and Restarting Setup Manually . . . . . . . . . . . . . . . . . 63
Stopping Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Restarting Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Setup Part 1: Basic System Configuration . . . . . . . . . . . . . . . . . 64
Setup Part 2: Port Configuration . . . . . . . . . . . . . . . . . . . . . 66
Setup Part 3: VLANs . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Setup Part 4: IP Configuration . . . . . . . . . . . . . . . . . . . . . . 69
IP Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Loopback Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . 70
Using Loopback Interfaces for Source IP Addresses . . . . . . . . . 70
Loopback Interface Limitations . . . . . . . . . . . . . . . . . . 71
Default Gateways . . . . . . . . . . . . . . . . . . . . . . . . . . 71
IP Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Setup Part 5: Final Steps . . . . . . . . . . . . . . . . . . . . . . . . . 73
Optional Setup for Telnet Support . . . . . . . . . . . . . . . . . . . . 74
Chapter 3. Switch Software Management . . . . . . . . . . . . . . 75
Loading New Software to Your Switch . . . . . . . . . . . . . . . . . . 76
Loading Software via the ISCLI . . . . . . . . . . . . . . . . . . . . 76
Loading Software via BBI . . . . . . . . . . . . . . . . . . . . . . 77
USB Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
USB Boot. . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
USB Copy . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
The Boot Management Menu . . . . . . . . . . . . . . . . . . . . . . 80
Recovering from a Failed Software Upgrade . . . . . . . . . . . . . . 80
Recovering from a Failed Boot Image . . . . . . . . . . . . . . . 83
Part 2: Securing the Switch
. . . . . . . . . . . . . . . . . . . 85
Chapter 4. Securing Administration . . . . . . . . . . . . . . . . 87
Secure Shell and Secure Copy . . . . . . . . . . . . . . . . . . . . . . 88
Configuring SSH/SCP Features on the Switch. . . . . . . . . . . . . . 88
To Enable or Disable the SSH Feature . . . . . . . . . . . . . . . 88
To Enable or Disable SCP Apply and Save . . . . . . . . . . . . . 89
Configuring the SCP Administrator Password . . . . . . . . . . . . . 89
Using SSH and SCP Client Commands . . . . . . . . . . . . . . . . 89
To Log Into the Switch . . . . . . . . . . . . . . . . . . . . . . 89
To Copy the Switch Configuration File to the SCP Host . . . . . . . 89
To Load a Switch Configuration File from the SCP Host . . . . . . . 90
To Apply and Save the Configuration . . . . . . . . . . . . . . . 90
To Copy the Switch Image and Boot Files to the SCP Host . . . . . . 90
To Load Switch Configuration Files from the SCP Host. . . . . . . . 91
SSH and SCP Encryption of Management Messages . . . . . . . . . . . 91
Generating RSA Host Key for SSH Access . . . . . . . . . . . . . . . 91
SSH/SCP Integration with Radius Authentication . . . . . . . . . . . . 91
SSH/SCP Integration with TACACS+ Authentication . . . . . . . . . . 92
4
G8052 Application Guide for ENOS 8.4
End User Access Control. . . . . . . . . . . . . . . . . . . . . . . . .93
Considerations for Configuring End User Accounts . . . . . . . . . . .93
Strong Passwords . . . . . . . . . . . . . . . . . . . . . . . . . .93
User Access Control . . . . . . . . . . . . . . . . . . . . . . . . .94
Setting up User IDs . . . . . . . . . . . . . . . . . . . . . . .94
Defining a User’s Access Level . . . . . . . . . . . . . . . . . .94
Validating a User’s Configuration . . . . . . . . . . . . . . . . .94
Enabling or Disabling a User . . . . . . . . . . . . . . . . . . .94
Locking Accounts . . . . . . . . . . . . . . . . . . . . . . . .94
Re‐Enabling Locked Accounts. . . . . . . . . . . . . . . . . . .95
Listing Current Users . . . . . . . . . . . . . . . . . . . . . . . .95
Logging into an End User Account . . . . . . . . . . . . . . . . . .95
Password Fix‐Up Mode . . . . . . . . . . . . . . . . . . . . . . .95
Chapter 5. Authentication & Authorization Protocols . . . . . . . . . 97
RADIUS Authentication and Authorization . . . . . . . . . . . . . . . .98
How RADIUS Authentication Works . . . . . . . . . . . . . . . . .98
Configuring RADIUS on the Switch . . . . . . . . . . . . . . . . . .98
RADIUS Authentication Features in Enterprise NOS . . . . . . . . . . 100
Switch User Accounts . . . . . . . . . . . . . . . . . . . . . . . 100
RADIUS Attributes for Enterprise NOS User Privileges . . . . . . . . 101
TACACS+ Authentication . . . . . . . . . . . . . . . . . . . . . . . 102
How TACACS+ Authentication Works. . . . . . . . . . . . . . . . 102
TACACS+ Authentication Features in Enterprise NOS . . . . . . . . . 103
Authorization . . . . . . . . . . . . . . . . . . . . . . . . . 103
Accounting . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Command Authorization and Logging . . . . . . . . . . . . . . . . 104
Configuring TACACS+ Authentication on the Switch . . . . . . . . . 105
LDAP Authentication and Authorization . . . . . . . . . . . . . . . . 106
Configuring the LDAP Server. . . . . . . . . . . . . . . . . . . . 106
Configuring LDAP Authentication on the Switch . . . . . . . . . . . 106
Chapter 6. 802.1X Port-Based Network Access Control . . . . . . . . 109
Extensible Authentication Protocol over LAN . . . . . . . . . . . . . . 110
EAPoL Authentication Process . . . . . . . . . . . . . . . . . . . . . 111
EAPoL Message Exchange . . . . . . . . . . . . . . . . . . . . . . . 112
EAPoL Port States . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Guest VLAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Supported RADIUS Attributes . . . . . . . . . . . . . . . . . . . . . 114
EAPoL Configuration Guidelines . . . . . . . . . . . . . . . . . . . . 116
Chapter 7. Access Control Lists . . . . . . . . . . . . . . . . . . 117
Summary of Packet Classifiers . . . . . . . . . . . . . . . . . . . . . 118
Summary of ACL Actions . . . . . . . . . . . . . . . . . . . . . . . 119
Assigning Individual ACLs to a Port . . . . . . . . . . . . . . . . . . 120
ACL Order of Precedence . . . . . . . . . . . . . . . . . . . . . . . 120
ACL Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Assigning ACL Groups to a Port . . . . . . . . . . . . . . . . . . . . 122
© Copyright Lenovo 2016
Contents
5
ACL Metering and Re‐Marking . . . . . . . . . . . . . . . . . . . . 122
Metering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Re‐Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
ACL Port Mirroring. . . . . . . . . . . . . . . . . . . . . . . . . . 123
Viewing ACL Statistics . . . . . . . . . . . . . . . . . . . . . . . . 123
ACL Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Enabling ACL Logging . . . . . . . . . . . . . . . . . . . . . . 124
Logged Information . . . . . . . . . . . . . . . . . . . . . . . . 124
Rate Limiting Behavior . . . . . . . . . . . . . . . . . . . . . . 125
Log Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
ACL Logging Limitations . . . . . . . . . . . . . . . . . . . . . 125
ACL Configuration Examples . . . . . . . . . . . . . . . . . . . . . 126
ACL Example 1 . . . . . . . . . . . . . . . . . . . . . . . . . . 126
ACL Example 2 . . . . . . . . . . . . . . . . . . . . . . . . . . 126
ACL Example 3 . . . . . . . . . . . . . . . . . . . . . . . . . . 127
ACL Example 4 . . . . . . . . . . . . . . . . . . . . . . . . . . 127
ACL Example 5 . . . . . . . . . . . . . . . . . . . . . . . . . . 127
ACL Example 6 . . . . . . . . . . . . . . . . . . . . . . . . . . 128
VLAN Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Management ACLs . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Using Storm Control Filters . . . . . . . . . . . . . . . . . . . . . . 132
Chapter 8. Secure Input/Output Module . . . . . . . . . . . . . . 133
SIOM Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Setting an SIOM Security Policy . . . . . . . . . . . . . . . . . . . . 135
Enabling and Disabling the SIOM . . . . . . . . . . . . . . . . . . 135
Using Protocols With SIOM . . . . . . . . . . . . . . . . . . . . 135
Insecure Protocols . . . . . . . . . . . . . . . . . . . . . . . 135
Secure Protocols . . . . . . . . . . . . . . . . . . . . . . . 136
Insecure Protocols Unaffected by SIOM . . . . . . . . . . . . . 137
Implementing Secure LDAP (LDAPS) . . . . . . . . . . . . . . . . . . 138
Enabling LDAPS . . . . . . . . . . . . . . . . . . . . . . . . . 138
Disabling LDAPS . . . . . . . . . . . . . . . . . . . . . . . . . 139
Syslogs and LDAPS . . . . . . . . . . . . . . . . . . . . . . . . 140
Using Cryptographic Mode . . . . . . . . . . . . . . . . . . . . . . 141
Part 3: Switch Basics . . . . . . . . . . . . . . . . . . . . . . 143
Chapter 9. VLANs. . . . . . . . . . . . . . . . . . . . . . . . 145
VLANs Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 146
VLANs and Port VLAN ID Numbers . . . . . . . . . . . . . . . . . . 146
VLAN Numbers . . . . . . . . . . . . . . . . . . . . . . . . . 146
PVID/Native VLAN Numbers . . . . . . . . . . . . . . . . . . . 147
VLAN Tagging/Trunk Mode . . . . . . . . . . . . . . . . . . . . . . 148
Ingress VLAN Tagging . . . . . . . . . . . . . . . . . . . . . . 151
Limitations. . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
VLAN Topologies and Design Considerations . . . . . . . . . . . . . . 153
Multiple VLANs with Tagging/Trunk Mode Adapters . . . . . . . . . 153
VLAN Configuration Example . . . . . . . . . . . . . . . . . . . 156
6
G8052 Application Guide for ENOS 8.4
Protocol‐Based VLANs . . . . . . . . . . . . . . . . . . . . . . . . 157
Port‐Based vs. Protocol‐Based VLANs . . . . . . . . . . . . . . . . 157
PVLAN Priority Levels . . . . . . . . . . . . . . . . . . . . . . 158
PVLAN Tagging/Trunk Mode . . . . . . . . . . . . . . . . . . . 158
PVLAN Configuration Guidelines . . . . . . . . . . . . . . . . . . 158
Configuring PVLAN . . . . . . . . . . . . . . . . . . . . . . . 159
Private VLANs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Private VLAN Ports . . . . . . . . . . . . . . . . . . . . . . . . 160
Configuration Guidelines . . . . . . . . . . . . . . . . . . . . . 161
Configuration Example . . . . . . . . . . . . . . . . . . . . . . 161
Chapter 10. Ports and Link Aggregation . . . . . . . . . . . . . . 163
Aggregation Overview . . . . . . . . . . . . . . . . . . . . . . . . 164
Static LAGs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Static LAG Requirements . . . . . . . . . . . . . . . . . . . . . 165
Static Aggregation Configuration Rules . . . . . . . . . . . . . . . 166
Configuring a Static LAG . . . . . . . . . . . . . . . . . . . . . 166
Link Aggregation Control Protocol . . . . . . . . . . . . . . . . . . . 168
Static LACP LAGs. . . . . . . . . . . . . . . . . . . . . . . . . 169
LACP Port Modes . . . . . . . . . . . . . . . . . . . . . . . . . 169
LACP Individual . . . . . . . . . . . . . . . . . . . . . . . . . 170
LACP Minimum Links Option . . . . . . . . . . . . . . . . . . . 170
LACP Configuration Guidelines . . . . . . . . . . . . . . . . . . 171
Configuring LACP . . . . . . . . . . . . . . . . . . . . . . . . 172
Configurable LAG Hash Algorithm . . . . . . . . . . . . . . . . . . . 173
Packet‐Based LAG Hashing . . . . . . . . . . . . . . . . . . . . 173
Port‐Based LAG Hashing . . . . . . . . . . . . . . . . . . . . . 174
Chapter 11. Spanning Tree Protocols. . . . . . . . . . . . . . . . 177
Spanning Tree Protocol Modes . . . . . . . . . . . . . . . . . . . . . 178
Global STP Control . . . . . . . . . . . . . . . . . . . . . . . . . . 179
PVRST Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Port States . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
Bridge Protocol Data Units . . . . . . . . . . . . . . . . . . . . . 180
How BPDU Works. . . . . . . . . . . . . . . . . . . . . . . 180
Determining the Path for Forwarding BPDUs . . . . . . . . . . . 180
Simple STP Configuration . . . . . . . . . . . . . . . . . . . . . 182
Per‐VLAN Spanning Tree Groups . . . . . . . . . . . . . . . . . . 184
Using Multiple STGs to Eliminate False Loops. . . . . . . . . . . 184
VLANs and STG Assignment . . . . . . . . . . . . . . . . . . 185
Manually Assigning STGs . . . . . . . . . . . . . . . . . . . 185
Guidelines for Creating VLANs . . . . . . . . . . . . . . . . . 186
Rules for VLAN Tagged/Trunk Mode Ports . . . . . . . . . . . . 186
Adding and Removing Ports from STGs . . . . . . . . . . . . . 187
The Switch‐Centric Model . . . . . . . . . . . . . . . . . . . 188
Configuring Multiple STGs . . . . . . . . . . . . . . . . . . . . . 189
Rapid Spanning Tree Protocol . . . . . . . . . . . . . . . . . . . . . 191
Port States . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
RSTP Configuration Guidelines . . . . . . . . . . . . . . . . . . . 191
RSTP Configuration Example . . . . . . . . . . . . . . . . . . . . 192
© Copyright Lenovo 2016
Contents
7
Multiple Spanning Tree Protocol . . . . . . . . . . . . . . . . . . . . 193
MSTP Region. . . . . . . . . . . . . . . . . . . . . . . . . . . 193
Common Internal Spanning Tree . . . . . . . . . . . . . . . . . . 193
MSTP Configuration Guidelines . . . . . . . . . . . . . . . . . . 194
MSTP Configuration Examples . . . . . . . . . . . . . . . . . . . 194
MSTP Example 1 . . . . . . . . . . . . . . . . . . . . . . . 194
MSTP Example 2 . . . . . . . . . . . . . . . . . . . . . . . 195
Port Type and Link Type . . . . . . . . . . . . . . . . . . . . . . . 197
Edge/Portfast Port . . . . . . . . . . . . . . . . . . . . . . . . 197
Link Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
Chapter 12. Virtual Link Aggregation Groups . . . . . . . . . . . . 199
VLAG Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
VLAGs versus Port LAGs . . . . . . . . . . . . . . . . . . . . . . . 202
Configuring VLAGs . . . . . . . . . . . . . . . . . . . . . . . . . 204
Basic VLAG Configuration . . . . . . . . . . . . . . . . . . . . . 205
Configuring the ISL . . . . . . . . . . . . . . . . . . . . . . 205
Configuring the VLAG. . . . . . . . . . . . . . . . . . . . . 206
VLAG Configuration ‐ VLANs Mapped to MSTI . . . . . . . . . 208
VLAGs with VRRP . . . . . . . . . . . . . . . . . . . . . . . . 212
Task 1: Configure VLAG Peer 1 . . . . . . . . . . . . . . . . . 212
Task 2: Configure VLAG Peer 2 . . . . . . . . . . . . . . . . . 215
Two‐tier vLAGs with VRRP . . . . . . . . . . . . . . . . . . . . 218
vLAG Peer Gateway . . . . . . . . . . . . . . . . . . . . . . . 219
FDB Refresh . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
Configuring VLAGs in Multiple Layers . . . . . . . . . . . . . . . 220
Task 1: Configure Layer 2/3 border switches. . . . . . . . . . . . 220
Task 2: Configure switches in the Layer 2 region. . . . . . . . . . 221
Chapter 13. Quality of Service . . . . . . . . . . . . . . . . . . 225
QoS Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
Using ACL Filters . . . . . . . . . . . . . . . . . . . . . . . . . . 227
Summary of ACL Actions . . . . . . . . . . . . . . . . . . . . . 227
ACL Metering and Re‐Marking . . . . . . . . . . . . . . . . . . . 228
Metering . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Re‐Marking . . . . . . . . . . . . . . . . . . . . . . . . . 228
Using DSCP Values to Provide QoS . . . . . . . . . . . . . . . . . . . 229
Differentiated Services Concepts . . . . . . . . . . . . . . . . . . 229
Per Hop Behavior . . . . . . . . . . . . . . . . . . . . . . . . . 231
QoS Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
DSCP Re‐Marking and Mapping . . . . . . . . . . . . . . . . . . 232
DSCP Re‐Marking Configuration Examples . . . . . . . . . . . . . 233
DSCP Re‐Marking Configuration Example 1 . . . . . . . . . . . 233
DSCP Re‐Marking Configuration Example 2 . . . . . . . . . . . 233
Using 802.1p Priority to Provide QoS . . . . . . . . . . . . . . . . . . 235
Queuing and Scheduling . . . . . . . . . . . . . . . . . . . . . . . 236
Control Plane Protection . . . . . . . . . . . . . . . . . . . . . . . 236
8
G8052 Application Guide for ENOS 8.4
WRED with ECN . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
How WRED/ECN work together . . . . . . . . . . . . . . . . . . 237
Configuring WRED/ECN. . . . . . . . . . . . . . . . . . . . . . 238
WRED/ECN Configuration Example. . . . . . . . . . . . . . . . . 239
Configure Global Profile for WRED . . . . . . . . . . . . . . . 239
Configure Port‐level Profile for WRED . . . . . . . . . . . . . . 240
Configure Global Profile for ECN . . . . . . . . . . . . . . . . 240
Configure Port‐level Profile for ECN . . . . . . . . . . . . . . . 241
Verify WRED/ECN . . . . . . . . . . . . . . . . . . . . . . 242
Part 4: Advanced Switching Features. . . . . . . . . . . . . . . . 243
Chapter 14. OpenFlow . . . . . . . . . . . . . . . . . . . . . . 245
OpenFlow Overview . . . . . . . . . . . . . . . . . . . . . . . . . 246
Switch Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
OpenFlow Versions . . . . . . . . . . . . . . . . . . . . . . . . . . 248
OpenFlow Instance . . . . . . . . . . . . . . . . . . . . . . . . . . 249
Flow Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250
Static Flows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Port Membership . . . . . . . . . . . . . . . . . . . . . . . . . 254
FDB Aging and ECMP with OpenFlow. . . . . . . . . . . . . . . . 254
Static Flow Examples . . . . . . . . . . . . . . . . . . . . . . . 255
Table‐Miss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
Fail Secure Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
Emergency Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
OpenFlow Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
OpenFlow Edge Ports . . . . . . . . . . . . . . . . . . . . . . . 261
Link Aggregation . . . . . . . . . . . . . . . . . . . . . . . . . 262
Data Path ID . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
sFlow Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . 264
OpenFlow Groups . . . . . . . . . . . . . . . . . . . . . . . . . . 265
Configuring OpenFlow . . . . . . . . . . . . . . . . . . . . . . . . 266
Configuration Example 1 ‐ OpenFlow Boot Profile . . . . . . . . . . . 266
Configuration Example 2 ‐ Default Boot Profile . . . . . . . . . . . . 269
Feature Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . 271
Chapter 15. Virtualization. . . . . . . . . . . . . . . . . . . . . 273
Chapter 16. Stacking . . . . . . . . . . . . . . . . . . . . . . 275
Stacking Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 276
Stacking Requirements. . . . . . . . . . . . . . . . . . . . . . . 276
Stacking Limitations . . . . . . . . . . . . . . . . . . . . . . . . 277
© Copyright Lenovo 2016
Contents
9
Stack Membership . . . . . . . . . . . . . . . . . . . . . . . . . . 278
The Master Switch . . . . . . . . . . . . . . . . . . . . . . . . 278
Splitting and Merging One Stack . . . . . . . . . . . . . . . . 278
Merging Independent Stacks . . . . . . . . . . . . . . . . . . 279
Backup Switch Selection . . . . . . . . . . . . . . . . . . . . . . 280
Master Failover . . . . . . . . . . . . . . . . . . . . . . . . 280
Secondary Backup. . . . . . . . . . . . . . . . . . . . . . . 280
Master Recovery . . . . . . . . . . . . . . . . . . . . . . . 280
No Backup . . . . . . . . . . . . . . . . . . . . . . . . . . 281
Stack Member Identification . . . . . . . . . . . . . . . . . . . . 281
Configuring a Stack. . . . . . . . . . . . . . . . . . . . . . . . . . 282
Configuration Overview . . . . . . . . . . . . . . . . . . . . . . 282
Best Configuration Practices . . . . . . . . . . . . . . . . . . . . 282
Stacking VLANs . . . . . . . . . . . . . . . . . . . . . . . 283
Configuring Each Switch for the Stack . . . . . . . . . . . . . . . . 283
Additional Master Configuration . . . . . . . . . . . . . . . . . . 285
Configuring an External IPv4 Address for the Stack . . . . . . . . 285
Locating an External Stack Interface . . . . . . . . . . . . . . . 285
Viewing Stack Connections . . . . . . . . . . . . . . . . . . . 286
Binding Members to the Stack . . . . . . . . . . . . . . . . . 287
Assigning a Stack Backup Switch . . . . . . . . . . . . . . . . 287
Managing the Stack . . . . . . . . . . . . . . . . . . . . . . . . . . 288
Accessing the Master Switch CLI . . . . . . . . . . . . . . . . . . 288
Rebooting Stacked Switches via the Master . . . . . . . . . . . . . . 288
Upgrading Software in an Existing Stack . . . . . . . . . . . . . . . . 290
Replacing or Removing Stacked Switches . . . . . . . . . . . . . . . . 292
Removing a Switch from the Stack . . . . . . . . . . . . . . . . . 292
Installing the New Switch or Healing the Topology . . . . . . . . . . 292
Binding the New Switch to the Stack . . . . . . . . . . . . . . . . 294
Performing a Rolling Reload or Upgrade. . . . . . . . . . . . . . . 294
Starting a Rolling Reload . . . . . . . . . . . . . . . . . . . . 294
Starting a Rolling Upgrade . . . . . . . . . . . . . . . . . . . 295
Saving Syslog Messages . . . . . . . . . . . . . . . . . . . . . . . . 296
ISCLI Stacking Commands . . . . . . . . . . . . . . . . . . . . . . 298
Chapter 17. VMready . . . . . . . . . . . . . . . . . . . . . . 299
VE Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
Defining Server Ports . . . . . . . . . . . . . . . . . . . . . . . . . 300
VM Group Types . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
Local VM Groups . . . . . . . . . . . . . . . . . . . . . . . . . . 301
Distributed VM Groups . . . . . . . . . . . . . . . . . . . . . . . . 303
VM Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
Initializing a Distributed VM Group. . . . . . . . . . . . . . . . . 304
Assigning Members . . . . . . . . . . . . . . . . . . . . . . . . 304
Synchronizing the Configuration . . . . . . . . . . . . . . . . . . 305
Removing Member VEs . . . . . . . . . . . . . . . . . . . . . . 305
VMcheck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
10
G8052 Application Guide for ENOS 8.4
Virtual Distributed Switch . . . . . . . . . . . . . . . . . . . . . . . 308
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
Migrating to vDS . . . . . . . . . . . . . . . . . . . . . . . . . 309
Virtualization Management Servers . . . . . . . . . . . . . . . . . . . 310
Assigning a vCenter . . . . . . . . . . . . . . . . . . . . . . . . 310
vCenter Scans . . . . . . . . . . . . . . . . . . . . . . . . . . 311
Deleting the vCenter. . . . . . . . . . . . . . . . . . . . . . . . 311
Exporting Profiles . . . . . . . . . . . . . . . . . . . . . . . . . 312
VMware Operational Commands . . . . . . . . . . . . . . . . . . 312
Pre‐Provisioning VEs . . . . . . . . . . . . . . . . . . . . . . . . . 313
VLAN Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
VM Policy Bandwidth Control . . . . . . . . . . . . . . . . . . . . . 315
VM Policy Bandwidth Control Commands . . . . . . . . . . . . . . 315
Bandwidth Policies vs. Bandwidth Shaping. . . . . . . . . . . . . . 316
VMready Information Displays . . . . . . . . . . . . . . . . . . . . . 317
Local VE Information . . . . . . . . . . . . . . . . . . . . . . . 317
vCenter Hypervisor Hosts . . . . . . . . . . . . . . . . . . . . . 318
vCenter VEs . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
vCenter VE Details . . . . . . . . . . . . . . . . . . . . . . . . 320
vCenter Switchport Mapping Details . . . . . . . . . . . . . . . . 320
VMready Configuration Example . . . . . . . . . . . . . . . . . . . . 321
Chapter 18. Edge Virtual Bridging . . . . . . . . . . . . . . . . . 323
EVB Operations Overview . . . . . . . . . . . . . . . . . . . . . . . 324
VSIDB Synchronization . . . . . . . . . . . . . . . . . . . . . . 324
VLAN Behavior. . . . . . . . . . . . . . . . . . . . . . . . . . 325
Deleting a VLAN . . . . . . . . . . . . . . . . . . . . . . . . . 325
Manual Reflective Relay . . . . . . . . . . . . . . . . . . . . . . 325
EVB Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 326
Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328
Unsupported features . . . . . . . . . . . . . . . . . . . . . . . . . 328
Chapter 19. Static Multicast ARP . . . . . . . . . . . . . . . . . 329
Configuring Static Multicast ARP . . . . . . . . . . . . . . . . . . . . 330
Configuration Example . . . . . . . . . . . . . . . . . . . . . . 330
Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
Chapter 20. Dynamic ARP Inspection. . . . . . . . . . . . . . . . 333
Understanding ARP Spoofing Attacks . . . . . . . . . . . . . . . . 333
Understanding DAI . . . . . . . . . . . . . . . . . . . . . . . . 333
Interface Trust States and Network Security . . . . . . . . . . . . . 334
DAI Configuration Guidelines and Restrictions . . . . . . . . . . . . . . 336
DAI Configuration Example . . . . . . . . . . . . . . . . . . . . 336
Part 5: IP Routing . . . . . . . . . . . . . . . . . . . . . . . . 339
Chapter 21. Basic IP Routing . . . . . . . . . . . . . . . . . . . 341
IP Routing Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . 342
Routing Between IP Subnets . . . . . . . . . . . . . . . . . . . . . . 342
© Copyright Lenovo 2016
Contents
11
Example of Subnet Routing . . . . . . . . . . . . . . . . . . . . . . 343
Using VLANs to Segregate Broadcast Domains . . . . . . . . . . . . 344
Configuration Example . . . . . . . . . . . . . . . . . . . . . . 344
ECMP Static Routes. . . . . . . . . . . . . . . . . . . . . . . . . . 347
ECMP Route Hashing . . . . . . . . . . . . . . . . . . . . . . . 347
Configuring ECMP Static Routes . . . . . . . . . . . . . . . . . . 348
Dynamic Host Configuration Protocol. . . . . . . . . . . . . . . . . . 349
DHCP Relay Agent . . . . . . . . . . . . . . . . . . . . . . . . . . 350
Chapter 22. Policy-Based Routing . . . . . . . . . . . . . . . . . 351
PBR Policies and ACLs . . . . . . . . . . . . . . . . . . . . . . . . 352
Applying PBR ACLs . . . . . . . . . . . . . . . . . . . . . . . . . 352
Configuring Route Maps . . . . . . . . . . . . . . . . . . . . . . . 353
Match Clauses . . . . . . . . . . . . . . . . . . . . . . . . . . 353
Set Clauses. . . . . . . . . . . . . . . . . . . . . . . . . . . . 353
Configuring Health Check . . . . . . . . . . . . . . . . . . . . . 355
Example PBR Configuration . . . . . . . . . . . . . . . . . . . . . . 356
Configuring PBR with other Features . . . . . . . . . . . . . . . . . . 357
Unsupported Features . . . . . . . . . . . . . . . . . . . . . . . . 357
Chapter 23. Routed Ports . . . . . . . . . . . . . . . . . . . . 359
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
Configuring a Routed Port. . . . . . . . . . . . . . . . . . . . . . . 362
Configuring OSPF on Routed Ports . . . . . . . . . . . . . . . . . 362
OSPF Configuration Example . . . . . . . . . . . . . . . . . . . 363
Configuring RIP on Routed Ports . . . . . . . . . . . . . . . . . . 363
RIP Configuration Example . . . . . . . . . . . . . . . . . . . . 363
Configuring PIM on Routed Ports . . . . . . . . . . . . . . . . . . 364
PIM Configuration Example . . . . . . . . . . . . . . . . . . . . 364
Configuring BGP on Routed Ports. . . . . . . . . . . . . . . . . . 365
Configuring IGMP on Routed Ports . . . . . . . . . . . . . . . . . 365
Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366
Chapter 24. Internet Protocol Version 6 . . . . . . . . . . . . . . 367
IPv6 Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . 368
IPv6 Address Format . . . . . . . . . . . . . . . . . . . . . . . . . 369
IPv6 Address Types . . . . . . . . . . . . . . . . . . . . . . . . . 370
Unicast Address . . . . . . . . . . . . . . . . . . . . . . . . . 370
Multicast . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
Anycast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
IPv6 Address Autoconfiguration . . . . . . . . . . . . . . . . . . . . 372
IPv6 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373
Neighbor Discovery . . . . . . . . . . . . . . . . . . . . . . . . . 374
Neighbor Discovery Overview . . . . . . . . . . . . . . . . . . . 374
Host vs. Router . . . . . . . . . . . . . . . . . . . . . . . . . . 375
Supported Applications . . . . . . . . . . . . . . . . . . . . . . . . 376
Configuration Guidelines . . . . . . . . . . . . . . . . . . . . . . . 377
IPv6 Configuration Examples . . . . . . . . . . . . . . . . . . . . . 378
IPv6 Example 1 . . . . . . . . . . . . . . . . . . . . . . . . . . 378
IPv6 Example 2 . . . . . . . . . . . . . . . . . . . . . . . . . . 378
12
G8052 Application Guide for ENOS 8.4
Chapter 25. IPsec with IPv6 . . . . . . . . . . . . . . . . . . . . 381
IPsec Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
Using IPsec with the Lenovo RackSwitch G8052 . . . . . . . . . . . . . 383
Setting up Authentication . . . . . . . . . . . . . . . . . . . . . 383
Creating an IKEv2 Proposal . . . . . . . . . . . . . . . . . . . 384
Importing an IKEv2 Digital Certificate . . . . . . . . . . . . . . 384
Generating a Certificate Signing Request . . . . . . . . . . . . . 384
Generating an IKEv2 Digital Certificate. . . . . . . . . . . . . . 388
Enabling IKEv2 Preshared Key Authentication . . . . . . . . . . 388
Setting Up a Key Policy . . . . . . . . . . . . . . . . . . . . . . 389
Using a Manual Key Policy . . . . . . . . . . . . . . . . . . . . . 390
Using a Dynamic Key Policy . . . . . . . . . . . . . . . . . . . . 392
Chapter 26. Routing Information Protocol . . . . . . . . . . . . . . 393
Distance Vector Protocol . . . . . . . . . . . . . . . . . . . . . . . . 394
Stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
Routing Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
RIPv1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
RIPv2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
RIPv2 in RIPv1 Compatibility Mode. . . . . . . . . . . . . . . . . . . 395
RIP Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396
RIP Configuration Example . . . . . . . . . . . . . . . . . . . . . . 397
Chapter 27. Internet Group Management Protocol . . . . . . . . . . 399
IGMP Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400
How IGMP Works . . . . . . . . . . . . . . . . . . . . . . . . . . 401
IGMP Capacity and Default Values . . . . . . . . . . . . . . . . . . . 402
IGMP Snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . 404
IGMP Querier . . . . . . . . . . . . . . . . . . . . . . . . . . 404
Querier Election . . . . . . . . . . . . . . . . . . . . . . . . . 404
IGMP Groups . . . . . . . . . . . . . . . . . . . . . . . . . . 405
IGMPv3 Snooping. . . . . . . . . . . . . . . . . . . . . . . . . 405
IGMP Snooping Configuration Guidelines . . . . . . . . . . . . . . 407
IGMP Snooping Configuration Example . . . . . . . . . . . . . . . 408
Advanced Configuration Example: IGMP Snooping . . . . . . . . . . 409
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . 410
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 410
Troubleshooting IGMP Snooping . . . . . . . . . . . . . . . . . . 414
IGMP Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417
Configuration Guidelines . . . . . . . . . . . . . . . . . . . . . 417
Configure IGMP Relay. . . . . . . . . . . . . . . . . . . . . . . 418
Advanced Configuration Example: IGMP Relay . . . . . . . . . . . . 419
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . 419
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 420
Troubleshooting IGMP Relay . . . . . . . . . . . . . . . . . . . . 423
© Copyright Lenovo 2016
Contents
13
Additional IGMP Features . . . . . . . . . . . . . . . . . . . . . . . 426
FastLeave . . . . . . . . . . . . . . . . . . . . . . . . . . . . 426
IGMP Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . 426
Configuring the Range . . . . . . . . . . . . . . . . . . . . . 426
Configuring the Action . . . . . . . . . . . . . . . . . . . . 427
Configure IGMP Filtering . . . . . . . . . . . . . . . . . . . 427
Static Multicast Router. . . . . . . . . . . . . . . . . . . . . . . 427
Chapter 28. Multicast Listener Discovery . . . . . . . . . . . . . . 429
MLD Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430
How MLD Works . . . . . . . . . . . . . . . . . . . . . . . . . . 431
How Flooding Impacts MLD . . . . . . . . . . . . . . . . . . . . 432
MLD Querier. . . . . . . . . . . . . . . . . . . . . . . . . . . 432
Querier Election . . . . . . . . . . . . . . . . . . . . . . . . . 432
Dynamic Mrouters . . . . . . . . . . . . . . . . . . . . . . . . 433
MLD Capacity and Default Values . . . . . . . . . . . . . . . . . . . 434
Configuring MLD . . . . . . . . . . . . . . . . . . . . . . . . . . 435
Chapter 29. Border Gateway Protocol . . . . . . . . . . . . . . . 437
Internal Routing Versus External Routing . . . . . . . . . . . . . . . . 438
Route Reflector . . . . . . . . . . . . . . . . . . . . . . . . . . 439
Configuring Route Reflection . . . . . . . . . . . . . . . . . . 441
Restrictions. . . . . . . . . . . . . . . . . . . . . . . . . . 442
Forming BGP Peer Routers . . . . . . . . . . . . . . . . . . . . . . 443
Loopback Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . 444
What is a Route Map? . . . . . . . . . . . . . . . . . . . . . . . . . 444
Next Hop Peer IP Address . . . . . . . . . . . . . . . . . . . . . 445
Incoming and Outgoing Route Maps . . . . . . . . . . . . . . . . 445
Precedence. . . . . . . . . . . . . . . . . . . . . . . . . . . . 446
Configuration Overview . . . . . . . . . . . . . . . . . . . . . . 446
Aggregating Routes. . . . . . . . . . . . . . . . . . . . . . . . . . 448
Redistributing Routes . . . . . . . . . . . . . . . . . . . . . . . . . 448
BGP Communities . . . . . . . . . . . . . . . . . . . . . . . . . . 449
BGP Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450
Local Preference Attribute . . . . . . . . . . . . . . . . . . . . . 450
Metric (Multi‐Exit Discriminator) Attribute. . . . . . . . . . . . . . 450
Next Hop Attribute . . . . . . . . . . . . . . . . . . . . . . . . 451
Selecting Route Paths in BGP. . . . . . . . . . . . . . . . . . . . . . 452
Equal Cost Multi‐Path . . . . . . . . . . . . . . . . . . . . . . . 452
Multipath Relax . . . . . . . . . . . . . . . . . . . . . . . . . 452
BGP Failover Configuration . . . . . . . . . . . . . . . . . . . . . . 453
Default Redistribution and Route Aggregation Example . . . . . . . . . . 455
14
G8052 Application Guide for ENOS 8.4
Chapter 30. Open Shortest Path First . . . . . . . . . . . . . . . . 457
OSPFv2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 458
Types of OSPF Areas . . . . . . . . . . . . . . . . . . . . . . . 458
Types of OSPF Routing Devices . . . . . . . . . . . . . . . . . . . 459
Neighbors and Adjacencies . . . . . . . . . . . . . . . . . . . . . 460
The Link‐State Database . . . . . . . . . . . . . . . . . . . . . . 460
The Shortest Path First Tree . . . . . . . . . . . . . . . . . . . . 462
Internal Versus External Routing . . . . . . . . . . . . . . . . . . 462
OSPFv2 Implementation in Enterprise NOS . . . . . . . . . . . . . . . 463
Configurable Parameters . . . . . . . . . . . . . . . . . . . . . . 463
Defining Areas . . . . . . . . . . . . . . . . . . . . . . . . . . 464
Assigning the Area Index . . . . . . . . . . . . . . . . . . . . 464
Using the Area ID to Assign the OSPF Area Number . . . . . . . . 465
Attaching an Area to a Network . . . . . . . . . . . . . . . . . 465
Interface Cost . . . . . . . . . . . . . . . . . . . . . . . . . . . 466
Electing the Designated Router and Backup . . . . . . . . . . . . . 466
Summarizing Routes . . . . . . . . . . . . . . . . . . . . . . . 466
Default Routes . . . . . . . . . . . . . . . . . . . . . . . . . . 467
Virtual Links . . . . . . . . . . . . . . . . . . . . . . . . . . . 467
Router ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . 468
Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . 469
Configuring Plain Text OSPF Passwords . . . . . . . . . . . . . 470
Configuring MD5 Authentication . . . . . . . . . . . . . . . . 470
Host Routes for Load Balancing . . . . . . . . . . . . . . . . . . . 471
Loopback Interfaces in OSPF . . . . . . . . . . . . . . . . . . . . 472
OSPF Features Not Supported in This Release. . . . . . . . . . . . . 472
OSPFv2 Configuration Examples . . . . . . . . . . . . . . . . . . . . 473
Example 1: Simple OSPF Domain . . . . . . . . . . . . . . . . . . 474
Example 2: Virtual Links . . . . . . . . . . . . . . . . . . . . . . 476
Configuring OSPF for a Virtual Link on Switch #1 . . . . . . . . . 476
Configuring OSPF for a Virtual Link on Switch #2 . . . . . . . . . 477
Other Virtual Link Options . . . . . . . . . . . . . . . . . . . 479
Example 3: Summarizing Routes . . . . . . . . . . . . . . . . . . 480
Verifying OSPF Configuration . . . . . . . . . . . . . . . . . . . 481
OSPFv3 Implementation in Enterprise NOS . . . . . . . . . . . . . . . 482
OSPFv3 Differences from OSPFv2 . . . . . . . . . . . . . . . . . . 482
OSPFv3 Requires IPv6 Interfaces . . . . . . . . . . . . . . . . 482
OSPFv3 Uses Independent Command Paths . . . . . . . . . . . 482
OSPFv3 Identifies Neighbors by Router ID . . . . . . . . . . . . 483
Other Internal Improvements . . . . . . . . . . . . . . . . . . 483
OSPFv3 Limitations . . . . . . . . . . . . . . . . . . . . . . . . 483
OSPFv3 Configuration Example. . . . . . . . . . . . . . . . . . . 483
Neighbor Configuration Example . . . . . . . . . . . . . . . . . . 485
Chapter 31. Protocol Independent Multicast . . . . . . . . . . . . . 487
PIM Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 488
Supported PIM Modes and Features . . . . . . . . . . . . . . . . . . 489
© Copyright Lenovo 2016
Contents
15
Basic PIM Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 490
Globally Enabling or Disabling the PIM Feature. . . . . . . . . . . . 490
Defining a PIM Network Component . . . . . . . . . . . . . . . . 490
Defining an IP Interface for PIM Use . . . . . . . . . . . . . . . . 490
PIM Neighbor Filters . . . . . . . . . . . . . . . . . . . . . . . 491
Additional Sparse Mode Settings . . . . . . . . . . . . . . . . . . . . 493
Specifying the Rendezvous Point . . . . . . . . . . . . . . . . . . 493
Influencing the Designated Router Selection . . . . . . . . . . . . . 493
Specifying a Bootstrap Router . . . . . . . . . . . . . . . . . . . 494
Configuring a Loopback Interface . . . . . . . . . . . . . . . . . . 494
Using PIM with Other Features. . . . . . . . . . . . . . . . . . . . . 496
PIM with ACLs or VMAPs . . . . . . . . . . . . . . . . . . . . . 496
PIM with IGMP. . . . . . . . . . . . . . . . . . . . . . . . . . 496
PIM Configuration Examples . . . . . . . . . . . . . . . . . . . . . 497
Example 1: PIM‐SM with Dynamic RP . . . . . . . . . . . . . . . . 497
Example 2: PIM‐SM with Static RP . . . . . . . . . . . . . . . . . 498
Example 3: PIM‐DM. . . . . . . . . . . . . . . . . . . . . . . . 498
Part 6: High Availability Fundamentals . . . . . . . . . . . . . . . 501
Chapter 32. Basic Redundancy . . . . . . . . . . . . . . . . . . 503
Aggregating for Link Redundancy . . . . . . . . . . . . . . . . . . . 504
Virtual Link Aggregation . . . . . . . . . . . . . . . . . . . . . . . 504
Hot Links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 505
Forward Delay . . . . . . . . . . . . . . . . . . . . . . . . . . 505
Preemption . . . . . . . . . . . . . . . . . . . . . . . . . . . 505
FDB Update . . . . . . . . . . . . . . . . . . . . . . . . . . . 505
Configuration Guidelines . . . . . . . . . . . . . . . . . . . . . 505
Configuring Hot Links . . . . . . . . . . . . . . . . . . . . . . 506
Chapter 33. Layer 2 Failover . . . . . . . . . . . . . . . . . . . 507
Monitoring LAG Links . . . . . . . . . . . . . . . . . . . . . . . . 508
Setting the Failover Limit . . . . . . . . . . . . . . . . . . . . . . . 508
Manually Monitoring Port Links . . . . . . . . . . . . . . . . . . . . 509
Monitor Port State . . . . . . . . . . . . . . . . . . . . . . . . 509
Control Port State . . . . . . . . . . . . . . . . . . . . . . . . . 509
L2 Failover with Other Features . . . . . . . . . . . . . . . . . . . . 510
LACP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 510
Spanning Tree Protocol . . . . . . . . . . . . . . . . . . . . . . 510
Configuration Guidelines . . . . . . . . . . . . . . . . . . . . . . . 511
Configuring Layer 2 Failover. . . . . . . . . . . . . . . . . . . . . . 511
16
G8052 Application Guide for ENOS 8.4
Chapter 34. Virtual Router Redundancy Protocol . . . . . . . . . . . 513
VRRP Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 514
VRRP Components . . . . . . . . . . . . . . . . . . . . . . . . 514
Virtual Router. . . . . . . . . . . . . . . . . . . . . . . . . 514
Virtual Router MAC Address . . . . . . . . . . . . . . . . . . 514
Owners and Renters . . . . . . . . . . . . . . . . . . . . . . 514
Master and Backup Virtual Router . . . . . . . . . . . . . . . . 515
Virtual Interface Router . . . . . . . . . . . . . . . . . . . . 515
VRRP Operation . . . . . . . . . . . . . . . . . . . . . . . . . 515
Selecting the Master VRRP Router . . . . . . . . . . . . . . . . . . 516
Failover Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . 517
Active‐Active Redundancy . . . . . . . . . . . . . . . . . . . . . 517
Virtual Router Group . . . . . . . . . . . . . . . . . . . . . . . 517
Enterprise NOS Extensions to VRRP . . . . . . . . . . . . . . . . . . 518
Virtual Router Deployment Considerations . . . . . . . . . . . . . . . 519
Assigning VRRP Virtual Router ID . . . . . . . . . . . . . . . . . 519
Configuring the Switch for Tracking . . . . . . . . . . . . . . . . . 519
High Availability Configurations . . . . . . . . . . . . . . . . . . . . 520
VRRP High‐Availability Using Multiple VIRs . . . . . . . . . . . . . 520
Task 1: Configure G8052 1 . . . . . . . . . . . . . . . . . . . 521
Task 2: Configure G8052 2 . . . . . . . . . . . . . . . . . . . 522
VRRP High‐Availability Using VLAGs. . . . . . . . . . . . . . . . 524
Part 7: Network Management . . . . . . . . . . . . . . . . . . . 525
Chapter 35. Link Layer Discovery Protocol . . . . . . . . . . . . . 527
LLDP Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 528
Enabling or Disabling LLDP . . . . . . . . . . . . . . . . . . . . . . 529
Global LLDP Setting . . . . . . . . . . . . . . . . . . . . . . . . 529
Transmit and Receive Control . . . . . . . . . . . . . . . . . . . 529
LLDP Transmit Features . . . . . . . . . . . . . . . . . . . . . . . . 530
Scheduled Interval . . . . . . . . . . . . . . . . . . . . . . . . 530
Minimum Interval. . . . . . . . . . . . . . . . . . . . . . . . . 530
Time‐to‐Live for Transmitted Information . . . . . . . . . . . . . . 531
Trap Notifications . . . . . . . . . . . . . . . . . . . . . . . . . 531
Changing the LLDP Transmit State . . . . . . . . . . . . . . . . . 532
Types of Information Transmitted . . . . . . . . . . . . . . . . . . 532
LLDP Receive Features . . . . . . . . . . . . . . . . . . . . . . . . 534
Types of Information Received . . . . . . . . . . . . . . . . . . . 534
Viewing Remote Device Information . . . . . . . . . . . . . . . . 534
Time‐to‐Live for Received Information . . . . . . . . . . . . . . . . 536
LLDP Example Configuration . . . . . . . . . . . . . . . . . . . . . 538
Chapter 36. Simple Network Management Protocol . . . . . . . . . . 539
SNMP Version 1 & Version 2 . . . . . . . . . . . . . . . . . . . . . . 539
SNMP Version 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . 540
Configuring SNMP Trap Hosts . . . . . . . . . . . . . . . . . . . . . 542
SNMPv2 Trap Host Configuration. . . . . . . . . . . . . . . . . . 543
SNMPv3 Trap Host Configuration. . . . . . . . . . . . . . . . . . 544
SNMP MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545
© Copyright Lenovo 2016
Contents
17
Switch Images and Configuration Files . . . . . . . . . . . . . . . . . 552
Loading a New Switch Image . . . . . . . . . . . . . . . . . . . 553
Loading a Saved Switch Configuration . . . . . . . . . . . . . . . 553
Saving the Switch Configuration . . . . . . . . . . . . . . . . . . 554
Saving a Switch Dump . . . . . . . . . . . . . . . . . . . . . . 554
Chapter 37. Service Location Protocol . . . . . . . . . . . . . . . 555
Active DA Discovery . . . . . . . . . . . . . . . . . . . . . . . . . 556
SLP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . 557
Chapter 38. NETCONF . . . . . . . . . . . . . . . . . . . . . . 559
NETCONF Overview . . . . . . . . . . . . . . . . . . . . . . . . . 560
XML Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 561
Installing the NETCONF Client . . . . . . . . . . . . . . . . . . . . 562
Using Juniper Perl Client . . . . . . . . . . . . . . . . . . . . . . . 564
Establishing a NETCONF Session . . . . . . . . . . . . . . . . . . . 565
NETCONF Operations . . . . . . . . . . . . . . . . . . . . . . . . 567
Protocol Operations Examples . . . . . . . . . . . . . . . . . . . . . 568
<get‐config> . . . . . . . . . . . . . . . . . . . . . . . . . . . 568
<edit‐config> . . . . . . . . . . . . . . . . . . . . . . . . . . . 569
<copy‐config> . . . . . . . . . . . . . . . . . . . . . . . . . . 571
<delete‐config> . . . . . . . . . . . . . . . . . . . . . . . . . . 572
<lock> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 572
<unlock>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 573
<get> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 574
<close‐session> . . . . . . . . . . . . . . . . . . . . . . . . . . 575
<kill‐session> . . . . . . . . . . . . . . . . . . . . . . . . . . . 575
<get‐configuration> . . . . . . . . . . . . . . . . . . . . . . . . 576
<get‐interface‐information> . . . . . . . . . . . . . . . . . . . . 577
Part 8: Monitoring
. . . . . . . . . . . . . . . . . . . . . . . 581
Chapter 39. Remote Monitoring . . . . . . . . . . . . . . . . . . 583
RMON Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . 584
RMON Group 1—Statistics . . . . . . . . . . . . . . . . . . . . . . 585
RMON Group 2—History . . . . . . . . . . . . . . . . . . . . . . . 586
History MIB Object ID . . . . . . . . . . . . . . . . . . . . . . . 586
Configuring RMON History . . . . . . . . . . . . . . . . . . . . 586
RMON Group 3—Alarms . . . . . . . . . . . . . . . . . . . . . . . 587
Alarm MIB objects . . . . . . . . . . . . . . . . . . . . . . . . 587
Configuring RMON Alarms . . . . . . . . . . . . . . . . . . . . 587
RMON Alarm Configuration Example 1 . . . . . . . . . . . . . . . 588
RMON Alarm Configuration Example 2 . . . . . . . . . . . . . . . 588
RMON Group 9—Events . . . . . . . . . . . . . . . . . . . . . . . 589
Chapter 40. sFlow . . . . . . . . . . . . . . . . . . . . . . . 591
sFlow Statistical Counters . . . . . . . . . . . . . . . . . . . . . . . 591
sFlow Network Sampling . . . . . . . . . . . . . . . . . . . . . . . 591
sFlow Example Configuration . . . . . . . . . . . . . . . . . . . . . 592
18
G8052 Application Guide for ENOS 8.4
Chapter 41. Port Mirroring . . . . . . . . . . . . . . . . . . . . 593
Port Mirroring Model . . . . . . . . . . . . . . . . . . . . . . . . . 594
Configuring Port Mirroring . . . . . . . . . . . . . . . . . . . . . . 595
Part 9: Appendices . . . . . . . . . . . . . . . . . . . . . . . 597
Appendix A. Glossary . . . . . . . . . . . . . . . . . . . . . . 599
Appendix B. Getting help and technical assistance . . . . . . . . . . 601
Appendix C. Notices . . . . . . . . . . . . . . . . . . . . . . . 603
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 605
Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . 606
Recycling Information . . . . . . . . . . . . . . . . . . . . . . . . . 607
Particulate Contamination . . . . . . . . . . . . . . . . . . . . . . . 608
Telecommunication Regulatory Statement . . . . . . . . . . . . . . . . 609
Electronic Emission Notices . . . . . . . . . . . . . . . . . . . . . . 610
Federal Communications Commission (FCC) Statement . . . . . . . . 610
Industry Canada Class A Emission Compliance Statement . . . . . . . 610
Avis de Conformité à la Réglementation dʹIndustrie Canada . . . . . . 610
Australia and New Zealand Class A Statement . . . . . . . . . . . . 610
European Union ‐ Compliance to the Electromagnetic Compatibility Directive
610
Germany Class A Compliance Statement . . . . . . . . . . . . . . . 611
Japan VCCI Class A Statement . . . . . . . . . . . . . . . . . . . 612
Japan Electronics and Information Technology Industries Association (JEITA) Statement . . . . . . . . . . . . . . . . . . . . . . . . . 612
Korea Communications Commission (KCC) Statement . . . . . . . . . 613
Russia Electromagnetic Interference (EMI) Class A statement . . . . . . . . 614
People’s Republic of China Class A electronic emission statement . . . . . . 615
Taiwan Class A compliance statement . . . . . . . . . . . . . . . . . . 616
© Copyright Lenovo 2016
Contents
19
20
G8052 Application Guide for ENOS 8.4
Preface
This Application Guide describes how to configure and use the Lenovo Enterprise Network Operating System 8.4 software on the Lenovo RackSwitch G8052 (referred to as G8052 throughout this document). For documentation on installing the switch physically, see the Installation Guide for your G8052.
© Copyright Lenovo 2016
21
Who Should Use This Guide
This guide is intended for network installers and system administrators engaged in configuring and maintaining a network. The administrator should be familiar with Ethernet concepts, IP addressing, Spanning Tree Protocol, and SNMP configuration parameters.
22
G8052 Application Guide for ENOS 8.4
What You’ll Find in This Guide
This guide will help you plan, implement, and administer Enterprise NOS software. Where possible, each section provides feature overviews, usage examples, and configuration instructions. The following material is included:
Part 1: Getting Started
This material is intended to help those new to ENOS products with the basics of switch management. This part includes the following chapters:

Chapter 1, “Switch Administration,” describes how to access the G8052 to configure the switch and view switch information and statistics. This chapter discusses a variety of manual administration interfaces, including local management via the switch console, and remote administration via Telnet, a web browser, or via SNMP.

Chapter 2, “Initial Setup,” describes how to use the built‐in Setup utility to perform first‐time configuration of the switch.

Chapter 3, “Switch Software Management,” describes how to update the ENOS software operating on the switch.
Part 2: Securing the Switch

Chapter 4, “Securing Administration,” describes methods for using Secure Shell for administration connections, and configuring end‐user access control.

Chapter 5, “Authentication & Authorization Protocols,” describes different secure administration for remote administrators. This includes using Remote Authentication Dial‐in User Service (RADIUS), as well as TACACS+ and LDAP.

Chapter 6, “802.1X Port‐Based Network Access Control,” describes how to authenticate devices attached to a LAN port that has point‐to‐point connection characteristics. This feature prevents access to ports that fail authentication and authorization and provides security to ports of the G8052 that connect to blade servers.

Chapter 7, “Access Control Lists,” describes how to use filters to permit or deny specific types of traffic, based on a variety of source, destination, and packet attributes.

Chapter 8, “Secure Input/Output Module,” describes which protocols can be enabled. This feature allows secured traffic and secured authentication management.
Part 3: Switch Basics
© Copyright Lenovo 2016

Chapter 9, “VLANs,” describes how to configure Virtual Local Area Networks (VLANs) for creating separate network segments, including how to use VLAN tagging for devices that use multiple VLANs. This chapter also describes Protocol‐based VLANs, and Private VLANs.

Chapter 10, “Ports and Link Aggregation,” describes how to group multiple physical ports together to aggregate the bandwidth between large‐scale network devices.
Preface
23

Chapter 12, “Virtual Link Aggregation Groups,” describes using Virtual Link Aggregation Groups (VLAGs) to form LAGs spanning multiple VLAG‐capable aggregator switches.

Chapter 11, “Spanning Tree Protocols,” discusses how Spanning Tree Protocol (STP) configures the network so that the switch selects the most efficient path when multiple paths exist. Covers Rapid Spanning Tree Protocol (RSTP), Per‐VLAN Rapid Spanning Tree (PVRST), and Multiple Spanning Tree Protocol (MSTP).

Chapter 13, “Quality of Service,” discusses Quality of Service (QoS) features, including IP filtering using Access Control Lists (ACLs), Differentiated Services, and IEEE 802.1p priority values.
Part 4: Advanced Switching Features

Chapter 14, “OpenFlow,” describes how to create an OpenFlow Switch instance on the RackSwitch G8052.

Chapter 17, “Deployment Profiles,” describes how the G8052 can operate in different modes for different deployment scenarios, adjusting switch capacity levels to optimize performance for different types of networks.

Chapter 15, “Virtualization,” provides an overview of allocating resources based on the logical needs of the data center, rather than on the strict, physical nature of components.

Chapter 16, “Stacking,” describes how to combine multiple switches into a single, aggregate switch entity.

Chapter 17, “VMready,” discusses virtual machine (VM) support on the G8052.

Chapter 18, “Edge Virtual Bridging,” (EVB) discusses the IEEE 802.1Qbg—a standards‐based protocol that defines how virtual Ethernet bridges exchange configuration information. EVB bridges the gap between physical and virtual network resources, thus simplifying network management.

Chapter 19, “Static Multicast ARP,” discusses the configuration of a static ARP entry with multicast MAC address for Microsoft’s Network Load Balancing (NLB) feature to function efficiently.

Chapter 20, “Dynamic ARP Inspection,” discusses this security feature that lets a switch intercept and examine all ARP request and response packets in a subnet, discarding those packets with invalid IP to MAC address bindings. This capability protects the network from man‐in‐the‐middle attacks.

Chapter 21, “Basic IP Routing,” describes how to configure the G8052 for IP routing using IP subnets, BOOTP, and DHCP Relay.

Chapter 22, “Policy‐Based Routing describes how to configure the G8052 to forward traffic based on defined policies rather than entries in the routing table.

Chapter 23, “Routed Ports describes how to configure a switch port to forward Layer 3 traffic.

Chapter 24, “Internet Protocol Version 6,” describes how to configure the G8052 for IPv6 host management.
Part 5: IP Routing
24
G8052 Application Guide for ENOS 8.4

Chapter 25, “IPsec with IPv6,” describes how to configure Internet Protocol Security (IPsec) for securing IP communications by authenticating and encrypting IP packets, with emphasis on Internet Key Exchange version 2, and authentication/confidentiality for OSPFv3.

Chapter 26, “Routing Information Protocol,” describes how the ENOS software implements standard Routing Information Protocol (RIP) for exchanging TCP/IP route information with other routers.

Chapter 27, “Internet Group Management Protocol,” describes how the ENOS software implements IGMP Snooping or IGMP Relay to conserve bandwidth in a multicast‐switching environment.

Chapter 28, “Multicast Listener Discovery,” describes how Multicast Listener Discovery (MLD) is used with IPv6 to support host users requests for multicast data for a multicast group.

Chapter 29, “Border Gateway Protocol,” describes Border Gateway Protocol (BGP) concepts and features supported in ENOS.

Chapter 30, “Open Shortest Path First,” describes key Open Shortest Path First (OSPF) concepts and their implemented in ENOS, and provides examples of how to configure your switch for OSPF support.

Chapter 31, “Protocol Independent Multicast,” describes how multicast routing can be efficiently accomplished using the Protocol Independent Multicast (PIM) feature.
Part 6: High Availability Fundamentals

Chapter 32, “Basic Redundancy,” describes how the G8052 supports redundancy through LAGs and hotlinks.

Chapter 33, “Layer 2 Failover,” describes how the G8052 supports high‐availability network topologies using Layer 2 Failover.

Chapter 34, “Virtual Router Redundancy Protocol,” describes how the G8052 supports high‐availability network topologies using Virtual Router Redundancy Protocol (VRRP).
Part 7: Network Management
© Copyright Lenovo 2016

Chapter 35, “Link Layer Discovery Protocol,” describes how Link Layer Discovery Protocol helps neighboring network devices learn about each others’ ports and capabilities.

Chapter 36, “Simple Network Management Protocol,” describes how to configure the switch for management through an SNMP client.

Chapter 37, “Service Location Protocol,” describes the Service Location Protocol (SLP) that allows the switch to provide dynamic directory services.

Chapter 38, “NETCONF,” describes how to manage the G8052 using Network Configuration Protocol (NETCONF), a mechanism based on the Extensible Markup Language (XML).
Preface
25
Part 8: Monitoring

Chapter 39, “Remote Monitoring,” describes how to configure the RMON agent on the switch, so that the switch can exchange network monitoring data.

Chapter 40, “sFlow, described how to use the embedded sFlow agent for sampling network traffic and providing continuous monitoring information to a central sFlow analyzer.

Chapter 41, “Port Mirroring,” discusses tools how copy selected port traffic to a monitor port for network analysis.

Appendix A, “Glossary,” describes common terms and concepts used throughout this guide.

Appendix B, “Getting help and technical assistance,” provides details on where to go for additional information about Lenovo and Lenovo products.

Appendix C, “Notices,” contains safety and environmental notices.
Part 9: Appendices
26
G8052 Application Guide for ENOS 8.4
Additional References
Additional information about installing and configuring the G8052 is available in the following guides:
© Copyright Lenovo 2016

Lenovo RackSwitch G8052 Installation Guide

Lenovo RackSwitch G8052 ISCLI Command Reference for Lenovo Enterprise Network Operating System 8.4

Lenovo RackSwitch G8052 Release Notes for Lenovo Enterprise Network Operating System 8.4
Preface
27
Typographic Conventions
The following table describes the typographic styles used in this book.
Table 1. Typographic Conventions
Typeface or
Symbol
Meaning
Example
ABC123
This type is used for names of commands, files, and directories used within the text.
View the readme.txt file.
It also depicts on‐screen computer Main#
output and prompts.
ABC123
This bold type appears in Main# sys
command examples. It shows text that must be typed in exactly as shown.
<ABC123>
To establish a Telnet session, This italicized type appears in enter:
command examples as a parameter placeholder. Replace host# telnet <IP address>
the indicated text with the appropriate real name or value when using the command. Do not type the brackets.
This also shows book titles, special terms, or words to be emphasized.
Read your User’s Guide thoroughly.
[ ]
Command items shown inside brackets are optional and can be used or excluded as the situation demands. Do not type the brackets.
host# ls [­a]
|
The vertical bar ( | ) is used in command examples to separate choices where multiple options exist. Select only one of the listed options. Do not type the vertical bar.
host# set left|right
AaBbCc123
Click the Save button.
This block type depicts menus, buttons, and other controls that appear in Web browsers and other graphical interfaces.

28
G8052 Application Guide for ENOS 8.4
Part 1: Getting Started
© Copyright Lenovo 2016
29
30
G8052 Application Guide for ENOS 8.4
Chapter 1. Switch Administration
Your RackSwitch G8052 (G8052) is ready to perform basic switching functions right out of the box. Some of the more advanced features, however, require some administrative configuration before they can be used effectively.
The extensive Lenovo Enterprise Network Operating System switching software included in the G8052 provides a variety of options for accessing the switch to perform configuration, and to view switch information and statistics.
This chapter discusses the various methods that can be used to administer the switch.
© Copyright Lenovo 2016
31
Administration Interfaces
Enterprise NOS provides a variety of user‐interfaces for administration. These interfaces vary in character and in the methods used to access them: some are text‐based, and some are graphical; some are available by default, and some require configuration; some can be accessed by local connection to the switch, and others are accessed remotely using various client applications. For example, administration can be performed using any of the following:

A built‐in, text‐based command‐line interface and menu system for access via serial‐port connection or an optional Telnet or SSH session

The built‐in Browser‐Based Interface (BBI) available using a standard web‐browser

SNMP support for access through network management software such as IBM Director or HP OpenView
The specific interface chosen for an administrative session depends on user preferences, as well as the switch configuration and the available client tools.
In all cases, administration requires that the switch hardware is properly installed and turned on. (see the Lenovo RackSwitch G8052 Installation Guide).
Command Line Interface
The Industry Standard Command Line Interface (ISCLI) provides a simple, direct method for switch administration. Using a basic terminal, you can issue commands that allow you to view detailed information and statistics about the switch, and to perform any necessary configuration and switch software maintenance.
You can establish a connection to the ISCLI in any of the following ways:
Serial connection via the serial port on the G8052 (this option is always available)
 Telnet connection over the network
 SSH connection over the network

32
G8052 Application Guide for ENOS 8.4
Establishing a Connection
The factory default settings permit initial switch administration through only the built‐in serial port. All other forms of access require additional switch configuration before they can be used.
Remote access using the network requires the accessing terminal to have a valid, routable connection to the switch interface. The client IP address may be configured manually, or an IPv4 address can be provided automatically through the switch using a service such as DHCP or BOOTP relay (see “BOOTP/DHCP Client IP Address Services” on page 40), or an IPv6 address can be obtained using IPv6 stateless address configuration.
Note: Throughout this manual, IP address is used in places where either an IPv4 or IPv6 address is allowed. IPv4 addresses are entered in dotted‐decimal notation (for example, 10.10.10.1), while IPv6 addresses are entered in hexadecimal notation (for example, 2001:db8:85a3::8a2e:370:7334). In places where only one type of address is allowed, IPv4 address or IPv6 address is specified.
To manage the switch using Telnet, SNMP, or a Web browser, you must configure an IP interface.
When a DHCP server is present in the local network for the switch, the DHCP server will be used to configures the IP interface. However, if the switch fails to renew the address obtained through DHCP, the following factory configured settings will be used for IP interface 1:
IPv4 address: Mask:
Gateway:
DHCP: 192.168.49.50
255.255.255.0 192.168.49.255
enabled
If you manually configure a static IP address, DHCP is disabled. If you manually enable DHCP, the interface will be configured by the DHCP server. To access the switch, the following IP parameters must be configured: 1. Log on to the switch. 2. Enter IP interface mode. RS G8052> enable
RS G8052# configure terminal
RS G8052(config)# interface ip <IP interface number>
3. Configure the management IP interface/mask.

IPv4:
RS G8052(config­ip­if)# ip address <management interface IPv4 address>
RS G8052(config­ip­if)# ip netmask <IPv4 subnet mask>

IPv6:
RS G8052(config­ip­if)# ipv6 address <management interface IPv6 address>
RS G8052(config­ip­if)# ipv6 prefixlen <IPv6 prefix length>
© Copyright Lenovo 2016
Chapter 1: Switch Administration
33
4. Configure the VLAN, and enable the interface. RS G8052(config­ip­if)# vlan 1
RS G8052(config­ip­if)# enable
RS G8052(config­ip­if)# exit
5. Configure the default gateway.

IPv4:
RS G8052(config)# ip gateway <gateway number> address <IPv4 address>
RS G8052(config)# ip gateway <gateway number> enable

IPv6: RS G8052(config)# ip gateway6 <gateway number> address <IPv6 address>
RS G8052(config)# ip gateway6 <gateway number> enable
Once you configure the IP address and have a network connection, you can use the Telnet program from an external management station to access and control the switch. Once the default gateway is enabled, the management station and your switch do not need to be on the same IP subnet.
The G8052 supports an industry standard command‐line interface (ISCLI) that you can use to configure and control the switch over the network using the Telnet program. You can use the ISCLI to perform many basic network management functions. In addition, you can configure the switch for management using an SNMP‐based network management system or a Web browser.
For more information, see the documents listed in “Additional References” on page 27. Using Telnet
A Telnet connection offers the convenience of accessing the switch from a workstation connected to the network. Telnet access provides the same options for user and administrator access as those available through the console port.
By default, Telnet access is enabled. Use the following commands to disable or re‐enable Telnet access: RS G8052(config)# [no] access telnet enable
Once the switch is configured with an IP address and gateway, you can use Telnet to access switch administration from any workstation connected to the management network.
To establish a Telnet connection with the switch, run the Telnet program on your workstation and issue the following Telnet command:
telnet <switch IPv4 or IPv6 address> You will then be prompted to enter a password as explained “Switch Login Levels” on page 48.
Two attempts are allowed to log in to the switch. After the second unsuccessful attempt, the Telnet client is disconnected via TCP session closure.
34
G8052 Application Guide for ENOS 8.4
Using Secure Shell
Although a remote network administrator can manage the configuration of a G8052 via Telnet, this method does not provide a secure connection. The Secure Shell (SSH) protocol enables you to securely log into another device over a network to execute commands remotely. As a secure alternative to using Telnet to manage switch configuration, SSH ensures that all data sent over the network is encrypted and secure.
The switch can do only one session of key/cipher generation at a time. Thus, a SSH/SCP client will not be able to login if the switch is doing key generation at that time. Similarly, the system will fail to do the key generation if a SSH/SCP client is logging in at that time.
The supported SSH encryption and authentication methods are:

Server Host Authentication: Client RSA‐authenticates the switch when starting each connection

Key Exchange: ecdh‐sha2‐nistp521, ecdh‐sha2‐nistp384, ecdh‐sha2‐nistp256, ecdh‐sha2‐nistp224, ecdh‐sha2‐nistp192, rsa2048‐sha256, rsa1024‐sha1, diffie‐hellman‐group‐exchange‐sha256, diffie‐hellman‐group‐exchange‐sha1, diffie‐hellman‐group14‐sha1, diffie‐hellman‐group1‐sha1

Encryption: aes128‐ctr, aes128‐cbc, rijndael128‐cbc, blowfish‐cbc,3des‐cbc, arcfour256, arcfour128, arcfour

MAC: hmac‐sha1, hmac‐sha1‐96, hmac‐md5, hmac‐md5‐96

User Authentication: Local password authentication, public key authentication, RADIUS, TACACS+
Lenovo Enterprise Network Operating System implements the SSH version 2.0 standard and is confirmed to work with SSH version 2.0‐compliant clients such as the following:

OpenSSH_5.4p1 for Linux

Secure CRT Version 5.0.2 (build 1021)

Putty SSH release 0.60 Using SSH with Password Authentication
By default, the SSH feature is disabled. Once the IP parameters are configured and the SSH service is enabled, you can access the command line interface using an SSH connection.
To establish an SSH connection with the switch, run the SSH program on your workstation by issuing the SSH command, followed by the switch IPv4 or IPv6 address:
# ssh <switch IP address>
You will then be prompted to enter a password as explained “Switch Login Levels” on page 48.
© Copyright Lenovo 2016
Chapter 1: Switch Administration
35
Using SSH with Public Key Authentication
SSH can also be used for switch authentication based on asymmetric cryptography. Public encryption keys can be uploaded on the switch and used to authenticate incoming login attempts based on the clients’ private encryption key pairs. After a predefined number of failed public key login attempts, the switch reverts to password‐based authentication.
To set up public key authentication:
1. Enable SSH:
RS G8052(config)# ssh enable
2. Import the public key file using SFTP or TFTP for the admin user account::
RS G8052(config)# copy {sftp|tftp} public­key
Port type ["DATA"/"MGT"]: mgt
Address or name of remote host: 9.43.101.151
Source file name: 11.key
Username of the public key: admin
Confirm download operation (y/n) ? y
Notes:

When prompted to input a username, a valid user account name must be entered. If no username is entered, the key is stored on the switch, and can be assigned to a user account later.

A user account can have up to 100 public keys set up on the switch.
3. Configure a maximum number of 3 failed public key authentication attempts before the system reverts to password‐based authentication:
RS G8052(config)# ssh maxauthattempts 3
Once the public key is configured on the switch, the client can use SSH to login from a system where the private key pair is set up:
# ssh <switch IP address>
36
G8052 Application Guide for ENOS 8.4
Using a Web Browser
The switch provides a Browser‐Based Interface (BBI) for accessing the common configuration, management, and operation features of the G8052 through your Web browser.
By default, BBI access via HTTP is enabled on the switch.
You can also access the BBI directly from an open Web browser window. Enter the URL using the IP address of the switch interface (for example, http://<IPv4 or IPv6 address>).
Configuring HTTP Access to the BBI
By default, BBI access via HTTP is enabled on the switch.
To disable or re‐enable HTTP access to the switch BBI, use the following commands:
RS G8052(config)# access http enable
(Enable HTTP access)
‐or‐
RS G8052(config)# no access http enable
(Disable HTTP access)
The default HTTP web server port to access the BBI is port 80. However, you can change the default Web server port with the following command: RS G8052(config)# access http port <TCP port number> To access the BBI from a workstation, open a Web browser window and type in the URL using the IP address of the switch interface (for example, http://<IPv4 or IPv6 address>).
Configuring HTTPS Access to the BBI
The BBI can also be accessed via a secure HTTPS connection.
1. Enable HTTPS.
By default, BBI access is enabled via both HTTP and HTTPS on the switch. If HTTPS access has been disabled, use the following command to enable BBI Access via HTTPS: RS G8052(config)# access https enable
2. Set the HTTPS server port number (optional).
To change the HTTPS Web server port number from the default port 443, use the following command: RS G8052(config)# access https port <x>
3. Generate the HTTPS certificate.
© Copyright Lenovo 2016
Chapter 1: Switch Administration
37
Accessing the BBI via HTTPS requires that you generate a certificate to be used during the key exchange. A default certificate is created the first time HTTPS is enabled, but you can create a new certificate defining the information you want to be used in the various fields.
RS G8052(config)# access https generate­certificate
Country Name (2 letter code) [US]:
State or Province Name (full name) [CA]:
Locality Name (eg, city) [Santa Clara]:
Organization Name (eg, company) [Lenovo Networking Operating System]:
Organizational Unit Name (eg, section) [Network Engineering]:
Common Name (eg, YOUR name) [0.0.0.0]:
Email (eg, email address) []:
Confirm generating certificate? [y/n]: y
Generating certificate. Please wait (approx 30 seconds)
restarting SSL agent
4. Save the HTTPS certificate.
The certificate is valid only until the switch is rebooted. To save the certificate so it is retained beyond reboot or power cycles, use the following command: RS G8052(config)# access https save­certificate
When a client (such as a web browser) connects to the switch, the client is asked to accept the certificate and verify that the fields match what is expected. Once BBI access is granted to the client, the BBI can be used.
Browser-Based Interface Summary
The BBI is organized at a high level as follows:
Context buttons—These buttons allow you to select the type of action you wish to perform. The Configuration button provides access to the configuration elements for the entire switch. The Statistics button provides access to the switch statistics and state information. The Dashboard button allows you to display the settings and operating status of a variety of switch features.
Navigation Window—Provides a menu of switch features and functions: 38

System—Provides access to the configuration elements for the entire switch.

Switch Ports—Configure each of the physical ports on the switch.

Port‐Based Port Mirroring—Configure port mirroring behavior.

Layer 2—Configure Layer 2 features for the switch.

RMON Menu—Configure Remote Monitoring features for the switch.

Layer 3—Configure Layer 3 features for the switch.

QoS—Configure Quality of Service features for the switch.

Access Control—Configure Access Control Lists to filter IP packets.

Virtualization—Configure VMready .
G8052 Application Guide for ENOS 8.4
Using Simple Network Management Protocol
ENOS provides Simple Network Management Protocol (SNMP) version 1, version 2, and version 3 support for access through any network management software, such as IBM Director or HP‐OpenView.
Note: SNMP read and write functions are enabled by default. For best security practices, if SNMP is not needed for your network, it is recommended that you disable these functions prior to connecting the switch to the network.
To access the SNMP agent on the G8052, the read and write community strings on the SNMP manager must be configured to match those on the switch. The default read community string on the switch is public and the default write community string is private.
The read and write community strings on the switch can be configured using the following commands: RS G8052(config)# snmp­server read­community <1‐32 characters>
‐and‐
RS G8052(config)# snmp­server write­community <1‐32 characters>
The SNMP manager must be able to reach any one of the IP interfaces on the switch.
For the SNMP manager to receive the SNMPv1 traps sent out by the SNMP agent on the switch, configure the trap host on the switch with the following commands: RS G8052(config)# snmp­server trap­source <trap source IP interface>
RS G8052(config)# snmp­server host <IPv4 address> <trap host community string>
To restrict SNMP access to specific IPv4 subnets, use the following commands:
RS G8052(config)# access management­network <IPv4 address> <subnet mask> snmp­ro
‐and‐
RS G8052(config)# access management­network <IPv4 address> <subnet mask> snmp­rw
For IPv6 networks, use:
RS G8052(config)# access management­network6 <IPv6 address> <IPv6 prefix length> snmp­ro
‐and‐
RS G8052(config)# access management­network6 <IPv6 address> <IPv6 prefix length> snmp­rw
Note: Subnets allowed for SNMP read‐only access must not overlap with subnets allowed for SNMP read‐write access.
For more information on SNMP usage and configuration, see Chapter 36, “Simple Network Management Protocol.”
© Copyright Lenovo 2016
Chapter 1: Switch Administration
39
BOOTP/DHCP Client IP Address Services
For remote switch administration, the client terminal device must have a valid IP address on the same network as a switch interface. The IP address on the client device may be configured manually, or obtained automatically using IPv6 stateless address configuration, or an IPv4 address may obtained automatically via BOOTP or DHCP relay as discussed in the next section.
The G8052 can function as a relay agent for Bootstrap Protocol (BOOTP) or DHCP. This allows clients to be assigned an IPv4 address for a finite lease period, reassigning freed addresses later to other clients.
Acting as a relay agent, the switch can forward a client’s IPv4 address request to up to five BOOTP/DHCP servers. In addition to the five global BOOTP/DHCP servers, up to five domain‐specific BOOTP/DHCP servers can be configured for each of up to 10 VLANs.
When a switch receives a BOOTP/DHCP request from a client seeking an IPv4 address, the switch acts as a proxy for the client. The request is forwarded as a UDP Unicast MAC layer message to the BOOTP/DHCP servers configured for the client’s VLAN, or to the global BOOTP/DHCP servers if no domain‐specific BOOTP/DHCP servers are configured for the client’s VLAN. The servers respond to the switch with a Unicast reply that contains the IPv4 default gateway and the IPv4 address for the client. The switch then forwards this reply back to the client.
DHCP is described in RFC 2131, and the DHCP relay agent supported on the G8052 is described in RFC 1542. DHCP uses UDP as its transport protocol. The client sends messages to the server on port 67 and the server sends messages to the client on port 68.
BOOTP and DHCP relay are collectively configured using the BOOTP commands and menus on the G8052.
DHCP Host Name Configuration
The G8052 supports DHCP host name configuration as described in RFC 2132, option 12. DHCP host name configuration is enabled by default.
Host name can be manually configured using the following command: RS G8052(config)# hostname <name>
If the host name is manually configured, the switch does not replace it with the host name received from the DHCP server.
After the host name is configured on the switch, if DHCP or DHCP host name configuration is disabled, the switch retains the host name.
The switch prompt displays the host name. Host name configuration can be enabled or disabled using the following command: RS G8052(config)# [no] system dhcp hostname
40
G8052 Application Guide for ENOS 8.4
DHCP SYSLOG Server
During switch startup, if the switch fails to get the configuration file, a message can be recorded in the SYSLOG server.
The G8052 supports requesting of a SYSLOG server IP address from the DHCP server as described in RFC 2132, option 7. DHCP SYSLOG server request option is enabled by default.
Manually configured SYSLOG server takes priority over DHCP SYSLOG server. Up to two SYSLOG server addresses received from the DHCP server can be used. The SYSLOG server can be learnt over a management port or a data port.
Use the RS G8052# show logging command to view the SYSLOG server address.
DHCP SYSLOG server address option can be enabled/disabled using the following command: RS G8052(config)# [no] system dhcp syslog
Global BOOTP Relay Agent Configuration
To enable the G8052 to be a BOOTP (or DHCP) forwarder, enable the BOOTP relay feature, configure up to four global BOOTP server IPv4 addresses on the switch, and enable BOOTP relay on the interface(s) on which the client requests are expected.
Generally, it is best to configure BOOTP for the switch IP interface that is closest to the client, so that the BOOTP server knows from which IPv4 subnet the newly allocated IPv4 address will come.
In the G8052 implementation, there are no primary or secondary BOOTP servers. The client request is forwarded to all the global BOOTP servers configured on the switch (if no domain‐specific servers are configured). The use of multiple servers provides failover redundancy. However, no health checking is supported.
1. Use the following commands to configure global BOOTP relay servers: RS G8052(config)# ip bootp­relay enable
RS G8052(config)# ip bootp­relay server <1‐5> address <IPv4 address>
2. Enable BOOTP relay on the appropriate IP interfaces.
BOOTP/DHCP Relay functionality may be assigned on a per‐interface basis using the following commands: RS G8052(config)# interface ip <interface number>
RS G8052(config­ip­if)# relay
RS G8052(config­ip­if)# exit
© Copyright Lenovo 2016
Chapter 1: Switch Administration
41
Domain-Specific BOOTP Relay Agent Configuration
Use the following commands to configure up to five domain‐specific BOOTP relay agents for each of up to 10 VLANs: RS G8052(config)# ip bootp­relay bcast­domain <1‐10> vlan <VLAN number>
RS G8052(config)# ip bootp­relay bcast­domain <1‐10> server <1‐5> address <IPv4 address>
RS G8052(config)# ip bootp­relay bcast­domain <1‐10> enable
As with global relay agent servers, domain‐specific BOOTP/DHCP functionality may be assigned on a per‐interface basis (see Step 2 in page 41).
DHCP Option 82
DHCP Option 82 provides a mechanism for generating IP addresses based on the client device’s location in the network. When you enable the DHCP relay agent option on the switch, it inserts the relay agent information option 82 in the packet, and sends a unicast BOOTP request packet to the DHCP server. The DHCP server uses the option 82 field to assign an IP address, and sends the packet, with the original option 82 field included, back to the relay agent. DHCP relay agent strips off the option 82 field in the packet and sends the packet to the DHCP client.
Configuration of this feature is optional. The feature helps resolve several issues where untrusted hosts access the network. See RFC 3046 for details.
Use the following commands to configure DHCP Option 82:
RS G8052(config)# ip bootp­relay information enable (Enable Option 82)
RS G8052(config)# ip bootp­relay enable (Enable DHCP relay)
RS G8052(config)# ip bootp­relay server <1‐5> address <IP address>
DHCP Snooping
DHCP snooping provides security by filtering untrusted DHCP packets and by building and maintaining a DHCP snooping binding table. This feature is applicable only to IPv4 and only works in non‐stacking mode.
An untrusted interface is a port that is configured to receive packets from outside the network or firewall. A trusted interface receives packets only from within the network. By default, all DHCP ports are untrusted.
The DHCP snooping binding table contains the MAC address, IP address, lease time, binding type, VLAN number, and port number that correspond to the local untrusted interface on the switch; it does not contain information regarding hosts interconnected with a trusted interface. By default, DHCP snooping is disabled on all VLANs. You can enable DHCP snooping on one or more VLANs. You must enable DHCP snooping globally. To enable this feature, enter the following commands:
RS G8052(config)# ip dhcp snooping vlan <vlan number(s)>
RS G8052(config)# ip dhcp snooping
42
G8052 Application Guide for ENOS 8.4
Following is an example of DHCP snooping configuration, where the DHCP server and client are in VLAN 100, and the server connects using port 24. RS
RS
RS
RS
RS
G8052(config)# ip dhcp snooping vlan 100
G8052(config)# ip dhcp snooping
G8052(config)# interface port 24
G8052(config­if)# ip dhcp snooping trust(Optional; Set port as trusted)
G8052(config­if)# ip dhcp snooping information option­insert
(Optional; add DHCP option 82)
RS G8052(config­if)# ip dhcp snooping limit rate 100 (Optional; Set DHCP packet rate)
© Copyright Lenovo 2016
Chapter 1: Switch Administration
43
Easy Connect Wizard
Lenovo EasyConnect (EZC) is a feature designed to simplify switch configuration. A set of predefined configurations can be applied on the switch via ISCLI. By launching the EZC Wizard, you are prompted for a minimal set of input and the tool automatically customizes the switch software.
The EZC Wizard allows you to choose one of the following configuration modes:

Basic System mode supports settings for hostname, static management port IP, netmask, and gateway.

Transparent mode collects server and uplink port settings. Note: You can either accept the static defaults or enter a different port list for uplink and/or server ports.

Redundant mode refers to VLAG settings.
The EZC configuration will be applied immediately. Any existing configuration will be deleted, the current active or running configuration will not be merged or appended to the EZC configuration.
For any custom settings that are not included in the predefined configuration sets, the user has to do it manually.
Notes:

EZC is not available in stacking mode.

To support scripting, the feature also has a single‐line format. For more information, please refer to Lenovo Networking ISCLI Reference Guide.
Configuring the Easy Connect Wizard
To launch the EZC Wizard, use the following command: RS G8052# easyconnect
The wizard displays the available predefined configuration modes. You are prompted to select one of the following options: RS G8052# easyconnect Auto configures the switch into a set configuration based on the input provided.
Current configuration will be overwritten with auto configuration settings.
The wizard can be canceled anytime by pressing Ctrl+C.
Select which of the following features you want enabled:
#Configure Basic system (yes/no)?
#Configure Transparent mode (yes/no)?
#Configure Switch Redundant mode (yes/no)?
44
G8052 Application Guide for ENOS 8.4
Basic System Mode Configuration Example
This example shows the parameters available for configuration in Basic System mode: RS G8052# easyconnect Configure Basic system (yes/no)? y
Please enter "none" for no hostname.
Enter hostname(Default: None)? Host
Select management port number(Default: 1)?
Please enter "dhcp" for dhcp IP.
Select management IP address (Current: 10.241.13.32)? Enter management netmask(Current: 255.255.255.128)? Enter management gateway:(Current: 10.241.13.1)? Pending switch port configuration:
Hostname: host
Management interface:
Port: 1
IP: 10.241.13.32
Netmask: 255.255.255.128
Gateway: 10.241.13.1
Note: You can either accept the default values or enter new parameters.
Transparent Mode Configuration Example
This example shows the parameters available for configuration in Transparent mode:
RS G8052# #easyconnect Configure Transparent mode (yes/no)? y
Select Uplink Ports (Static Defaults: XGE1­XGE4)? The following Uplink ports will be enabled:
Uplink ports(1G/10G): XGE1­XGE4
Select Server Ports (Static Defaults: 1­48)? The following Server ports will be enabled:
Server ports(1G/10G): 1­48
Pending switch configuration:
Uplink Ports: XGE1­XGE4
Server Ports: 1­48
Disabled Ports: Confirm erasing current config to re­configure Easy Connect (yes/no)? © Copyright Lenovo 2016

If your selection for a port group contains ports of different mode or speed, the selection is not valid and you are guided to either select other ports or change the speed of the ports.

You can either accept the static defaults or enter a different port list for uplink and/or server ports.
Chapter 1: Switch Administration
45
Redundant Mode Configuration Example
This example shows the parameters available for configuration in Redundant mode: RS G8052# #easyconnect Configure Switch Redundant mode (yes/no)? y
Note: It is recommended to select Basic system configuration in order to set the management IP address used for vLAG health check.
Configure Basic system (yes/no)? y
Select management port (Default: 1)? Configure this switch as vLAG Primary or Secondary Peer (primary/secondary)? prim
Select ISL Ports (Static Defaults: XGE3,XGE4)?
The following ISL ports will be enabled:
ISL ports(10G) : XGE3,XGE4
Select vLAG TierID (Default: 101)? Select management IP address (Current: 192.168.49.50)? Enter management netmask (Current: 255.255.255.0)? Select Peer IP address for vLAG healthcheck (Default: 1.1.1.2)? Warning: vLAG healthcheck Peer IP is not reachable.
Do you want to select another Peer IP (yes/no)? y
Select Peer IP address for vLAG healthcheck (Default: 1.1.1.2)? Warning: vLAG healthcheck Peer IP is not reachable.
Do you want to select another Peer IP (yes/no)? n
Select Uplink Ports (Static Defaults: XGE1,XGE2)? The following Uplink ports will be enabled:
Uplink ports(10G): XGE1,XGE2
Select Downlink Ports (Static Defaults: 2­48)? The following Downlink ports will be enabled:
Downlink ports(100M): 32,33
Downlink ports(10/100/1000) : 2­31 34­48
46
G8052 Application Guide for ENOS 8.4
Please enter "none" for no hostname.
Enter hostname(Default: Primary VLAG)? Please enter "none" for no gateway.
Enter management gateway:(Default: 0.0.0.0)?
Pending switch configuration:
vLAG switch type: Primary
ISL Ports: XGE3,XGE4
vLAG TierID: 101
vLAG Peer IP: 1.1.1.2
Uplink Ports: XGE1,XGE2
Downlink Ports: 2­48
Disabled Ports: empty
Hostname: Primary VLAG
Management Port: 1
Management interface:
IP: 192.168.49.50
Netmask: 255.255.255.0
Gateway: 0.0.0.0
Confirm erasing current config to re­configure Easy Connect (yes/no)? Notes:
© Copyright Lenovo 2016

If your selection for a port group contains ports of different speed, the selection is not valid, and you are guided to either select other ports or change the speed of the ports.

All unused port are configured as shut down in the configuration dump.

You can either accept the static defaults or enter a different port list for ISL, uplink, and/or downlink ports.
Chapter 1: Switch Administration
47
Switch Login Levels
To enable better switch management and user accountability, three levels or classes of user access have been implemented on the G8052. Levels of access to CLI, Web management functions, and screens increase as needed to perform various switch management tasks. Conceptually, access classes are defined as follows: 
User interaction with the switch is completely passive—nothing can be changed on the G8052. Users may display information that has no security or privacy implications, such as switch statistics and current operational state information.

Operators can only effect temporary changes on the G8052. These changes will be lost when the switch is rebooted/reset. Operators have access to the switch management features used for daily switch operations. Because any changes an operator makes are undone by a reset of the switch, operators cannot severely impact switch operation.

Administrators are the only ones that may make permanent changes to the switch configuration—changes that are persistent across a reboot/reset of the switch. Administrators can access switch functions to configure and troubleshoot problems on the G8052. Because administrators can also make temporary (operator‐level) changes as well, they must be aware of the interactions between temporary and permanent changes.
Access to switch functions is controlled through the use of unique user names and passwords. Once you are connected to the switch via console, remote Telnet, or SSH, you are prompted to enter a password. The default user names/password for each access level are listed in the following table.
Note: It is recommended that you change the default switch passwords after initial configuration and as regularly as required under your network security policies.
Table 2. User Access Levels ‐ Default Settings
48
User
Account
Password Description and Tasks Performed
Status
user
user
The User has no direct responsibility for switch management. He or she can view all switch status information and statistics, but cannot make any configuration changes to the switch.
Disabled
oper
oper
The Operator manages all functions of the switch. The Operator can reset ports, except the management ports.
Disabled
admin
admin The superuser Administrator has complete Enabled
access to all menus, information, and configuration commands on the G8052, including the ability to change both the user and administrator passwords.
G8052 Application Guide for ENOS 8.4
Note: Access to each user level (except admin account) can be disabled by setting the password to an empty value. To disable admin account, use the command no access user administrator­enable. The Admin account can be disabled only if there is at least one user account enabled and configured with administrator privilege. © Copyright Lenovo 2016
Chapter 1: Switch Administration
49
Setup vs. the Command Line
Once the administrator password is verified, you are given complete access to the switch. If the switch is still set to its factory default configuration, the system will ask whether you wish to run Setup (see Chapter 2, “Initial Setup”), a utility designed to help you through the first‐time configuration process. If the switch has already been configured, the command line is displayed instead. If the switch does not start the setup utility automatically, you must manually start it.
50
G8052 Application Guide for ENOS 8.4
Idle Disconnect
By default, the switch will disconnect your Telnet session after 10 minutes of inactivity. This function is controlled by the idle timeout parameter, which can be set from 0 to 60 minutes, where 0 means the session will never timeout.
Use the following command to set the idle timeout value: RS G8052(config)# system idle <0‐60>
© Copyright Lenovo 2016
Chapter 1: Switch Administration
51
Boot Strict Mode
The implementations specified in this section are compliant with National Institute of Standards and Technology (NIST) Special Publication (SP) 800‐131A.
The RackSwitch G8052 can operate in two boot modes:

Compatibility mode (default): This is the default switch boot mode. This mode may use algorithms and key lengths that may not be allowed/acceptable by NIST SP 800‐131A specification. This mode is useful in maintaining compatibility with previous releases and in environments that have lesser data security requirements.

Strict mode: Encryption algorithms, protocols, and key lengths in strict mode are compliant with NIST SP 800‐131A specification.
When in boot strict mode, the switch uses Secure Sockets Layer (SSL)/Transport Layer Security (TLS) 1.2 protocols to ensure confidentiality of the data to and from the switch. Before enabling strict mode, ensure the following:

The software version on all connected switches is Enterprise NOS 8.4.

The supported protocol versions and cryptographic cipher suites between clients and servers are compatible. For example: if using SSH to connect to the switch, ensure that the SSH client supports SSHv2 and a strong cipher suite that is compliant with the NIST standard.

Compliant Web server certificate is installed on the switch, if using BBI.

A new self‐signed certificate is generated for the switch (RS G8052(config)# access https generate­certificate). The new certificate is generated using 2048‐bit RSA key and SHA‐256 digest.

Protocols that are not NIST SP 800‐131A compliant must be disabled or not used.

Only SSHv2 or higher is used.

The current configuration, if any, is saved in a location external to the switch. When the switch reboots, both the startup and running configuration are lost.
Only protocols/algorithms compliant with NIST SP 800‐131A specification are used/enabled on the switch. Please see the NIST SP 800‐131A publication for details. The following table lists the acceptable protocols and algorithms: Table 3. Acceptable Protocols and Algorithms

Protocol/Function Strict Mode Algorithm
52
Compatibility Mode Algorithm
BGP
BGP does not comply with NIST SP Acceptable
800‐131A specification. When in strict mode, BGP is disabled. How‐
ever, it can be enabled, if required.
Certificate
Generation
RSA‐2048
SHA‐256
RSA 2048
SHA 256
Certificate
Acceptance
RSA 2048 or higher
SHA 224 or higher
RSA
SHA, SHA2
G8052 Application Guide for ENOS 8.4
Table 3. Acceptable Protocols and Algorithms (continued)
Protocol/Function Strict Mode Algorithm
Compatibility Mode Algorithm
HTTPS
TLS 1.2 only
See “Acceptable Cipher Suites” on page 55; TLS 1.0, 1.1, 1.2
See “Acceptable Cipher Suites” on page 55; Key Exchange
DH Group 24
DH group 1, 2, 5, 14, 24
Encryption
3DES, AES‐128‐CBC
3DES, AES‐128‐CBC
Integrity
HMAC‐SHA1
HMAC‐SHA1, HMAC‐MD5
HMAC‐SHA1, HMAC‐MD5
IKE
IPSec
AH
HMAC‐SHA1
ESP
3DES, AES‐128‐CBC, HMAC‐SHA1 3DES, AES‐128‐CBC, HMAC‐SHA1, HMAC‐MD5
LDAP
LDAP does not comply with NIST Acceptable
SP 800‐131A specification. When in strict mode, LDAP is disabled. However, it can be enabled, if required.
OSPF
OSPF does not comply with NIST SP Acceptable
800‐131A specification. When in strict mode, OSPF is disabled. How‐
ever, it can be enabled, if required.
RADIUS
Acceptable
RADIUS does not comply with NIST SP 800‐131A specification. When in strict mode, RADIUS is dis‐
abled. However, it can be enabled, if required.
Random Number Generator
NIST SP 800‐90A AES CTR DRBG
Secure NTP
Secure NTP does not comply with Acceptable
NIST SP 800‐131A specification. When in strict mode, secure NTP is disabled. However, it can be enabled, if required.
SLP
SHA‐256 or higher
RSA/DSA 2048 or higher
SNMP
SNMPv3 only
AES‐128‐CFB‐128/SHA1
NIST SP 800‐90A AES CTR DRBG
SNMPv1, SNMPv2, SNMPv3
DES/MD5, AES‐128‐CFB‐128/SHA1
Note: Following algorithms are acceptable if you choose to support old SNMPv3 factory default users:
AES‐128‐CFB/SHA1
DES/MD5
AES‐128‐CFB‐128/SHA1
© Copyright Lenovo 2016
Chapter 1: Switch Administration
53
Table 3. Acceptable Protocols and Algorithms (continued)
Protocol/Function Strict Mode Algorithm
Compatibility Mode Algorithm
SSH/SFTP 54
Host Key
SSH‐RSA
SSH‐RSA
Key Exchange
ECDH‐SHA2‐NISTP521
ECDH‐SHA2‐NISTP384
ECDH‐SHA2‐NISTP256
ECDH‐SHA2‐NISTP224
RSA2048‐SHA256
DIFFIE‐HELLMAN‐GROUP‐EXCH
ANGE‐SHA256
DIFFIE‐HELLMAN‐GROUP‐EXCH
ANGE‐SHA1
ECDH‐SHA2‐NISTP521
ECDH‐SHA2‐NISTP384
ECDH‐SHA2‐NISTP256
ECDH‐SHA2‐NISTP224
ECDH‐SHA2‐NISTP192
RSA2048‐SHA256
RSA1024‐SHA1
DIFFIE‐HELLMAN‐GROUP‐EX
CHANGE‐SHA256
DIFFIE‐HELLMAN‐GROUP‐EX
CHANGE‐SHA1
DIFFIE‐HELLMAN‐GROUP14‐S
HA1
DIFFIE‐HELLMAN‐GROUP1‐S
HA1
Encryption
AES128‐CTR
AES128‐CBC
3DES‐CBC
AES128‐CTR
AES128‐CBC
RIJNDAEL128‐CBC
BLOWFISH‐CBC
3DES‐CBC
ARCFOUR256
ARCFOUR128
ARCFOUR
MAC
HMAC‐SHA1
HMAC‐SHA1‐96
HMAC‐SHA1
HMAC‐SHA1‐96
HMAC‐MD5
HMAC‐MD5‐96
TACACS+
TACACS+ does not comply with NIST SP 800‐131A specification. When in strict mode, TACACS+ is disabled. However, it can be enabled, if required.
Acceptable
G8052 Application Guide for ENOS 8.4
Acceptable Cipher Suites
The following cipher suites are acceptable (listed in the order of preference) when the RackSwitch G8052 is in compatibility mode: Table 4. List of Acceptable Cipher Suites in Compatibility Mode
Cipher ID Key Exchange
0xC027
ECDHE
0xC013
ECDHE
0xC012
ECDHE
Authenti­ Encryption MAC
cation
RSA
AES_128_
SHA256
CBC
RSA
AES_128_
SHA1
CBC
RSA
3DES
SHA1
Cipher Name
0xC011
ECDHE
RSA
RC4
SHA1
SSL_ECDHE_RSA_WITH_RC4_128_SHA
0x002F
RSA
RSA
SHA1
TLS_RSA_WITH_AES_128_CBC_SHA
0x003C
RSA
RSA
SHA256
TLS_RSA_WITH_AES_128_CBC_SHA256
0x0005
RSA
RSA
AES_128_
CBC
AES_128_
CBC
RC4
SHA1
SSL_RSA_WITH_RC4_128_SHA
0x000A
RSA
RSA
3DES
SHA1
SSL_RSA_WITH_3DES_EDE_CBC_SHA
0x0033
DHE
RSA
0x0067
DHE
RSA
0x0016
DHE
RSA
AES­128_CB SHA1
C
AES_128_CB SHA256
C
3DES
SHA1
TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA2
56
TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA
SSL_ECDHE_RSA_WITH_3DES_EDE_CBC_SHA
TLS_DHE_RSA_WITH_AES_128_CBC_SHA
TLS_DHE_RSA_WITH_AES_128_CBC_SHA256
SSL_DHE_RSA_WITH_3DES_EDE_CBC_SHA
The following cipher suites are acceptable (listed in the order of preference) when the RackSwitch G8052 is in strict mode: Table 5. List of Acceptable Cipher Suites in Strict Mode
Cipher ID Key Exchange
0xC027
ECDHE
© Copyright Lenovo 2016
0xC013
ECDHE
0xC012
ECDHE
Authenti­ Encryption MAC
cation
RSA
AES_128_
SHA256
CBC
RSA
AES_128_
SHA1
CBC
RSA
3DES
SHA1
0x0033
DHE
RSA
0x0067
DHE
RSA
0x0016
DHE
RSA
0x002F
RSA
RSA
0x003C
RSA
RSA
0x000A
RSA
RSA
AES­128_
CBC
AES_128_
CBC
3DES
AES_128_
CBC
AES_128_
CBC
3DES
Cipher Name
TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA2
56
TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA
SSL_ECDHE_RSA_WITH_3DES_EDE_CBC_SHA
SHA1
TLS_DHE_RSA_WITH_AES_128_CBC_SHA
SHA256
TLS_DHE_RSA_WITH_AES_128_CBC_SHA256
SHA1
SSL_DHE_RSA_WITH_3DES_EDE_CBC_SHA
SHA1
TLS_RSA_WITH_AES_128_CBC_SHA
SHA256
TLS_RSA_WITH_AES_128_CBC_SHA256
SHA1
SSL_RSA_WITH_3DES_EDE_CBC_SHA
Chapter 1: Switch Administration
55
Configuring Strict Mode
To change the switch mode to boot strict mode, use the following command: RS G8052(config)# [no] boot strict enable
When strict mode is enabled, you will see the following message: Warning, security strict mode limits the cryptographic algorithms used by secure protocols on this switch. Please see the documentation for full details, and verify that peer devices support acceptable algorithms before enabling this mode. The mode change will take effect after reloading the switch and the configuration will be wiped during the reload. System will enter security strict mode with default factory configuration at next boot up. Do you want SNMPV3 support old default users in strict mode (y/n)?
For SNMPv3 default users, see “SNMP Version 3” on page 540.
When strict mode is disabled, the following message is displayed: Warning, disabling security strict mode. The mode change will take effect after reloading the switch.
You must reboot the switch for the boot strict mode enable/disable to take effect.
Configuring No-Prompt Mode
If you expect to administer the switch using SNSC or another browser‐based interface, you need to turn off confirmation prompts. To accomplish this, use the command: RS G8052(config)# [no] terminal dont­ask
In no‐prompt mode, confirmation prompts are disabled for this and future sessions.
SSL/TLS Version Limitation
Each of the following successive encryption protocol versions provide more security and less compatibility: SSLv3, TLS1.0, TLS1.1, TLS1.2. When negotiating the encryption protocol during the SSL handshake, the switch will accept, by default, the latest (and most secure) protocol version supported by the client equipment. To enforce a minimal level of security acceptable for the connections, use the following command:
RS G8052(config)# ssl minimum­version {ssl|tls10|tls11|tls12}
Limitations
In Enterprise NOS 8.4, consider the following limitation/restrictions if you need to operate the switch in boot strict mode:
56
G8052 Application Guide for ENOS 8.4
© Copyright Lenovo 2016

Power ITEs and High‐Availability features do not comply with NIST SP 800‐131A specification.

The G8052 will not discover Platform agents/Common agents that are not in strict mode.

Web browsers that do not use TLS 1.2 cannot be used.

Limited functions of the switch managing Windows will be available.
Chapter 1: Switch Administration
57
58
G8052 Application Guide for ENOS 8.4
Chapter 2. Initial Setup
To help with the initial process of configuring your switch, the Lenovo Enterprise Network Operating System software includes a Setup utility. The Setup utility prompts you step‐by‐step to enter all the necessary information for basic configuration of the switch.
Whenever you log in as the system administrator under the factory default configuration, you are asked whether you wish to run the Setup utility. Setup can also be activated manually from the command line interface any time after login.
© Copyright Lenovo 2016
59
Information Needed for Setup
Setup requests the following information:




60
Basic system information

Date & time

Whether to use Spanning Tree Group or not
Optional configuration for each port

Speed, duplex, flow control, and negotiation mode (as appropriate)

Whether to use VLAN trunk mode/tagging or not (as appropriate)
Optional configuration for each VLAN

Name of VLAN

Which ports are included in the VLAN
Optional configuration of IP parameters

IP address/mask and VLAN for each IP interface

IP addresses for default gateway

Whether IP forwarding is enabled or not
G8052 Application Guide for ENOS 8.4
Default Setup Options
The Setup prompt appears automatically whenever you login as the system administrator under the factory default settings.
1. Connect to the switch.
After connecting, the login prompt appears.
Enter Password:
2. Enter admin as the default administrator password.
If the factory default configuration is detected, the system prompts:
Lenovo RackSwitch G8052
18:44:05 Wed Jan 3, 2009 The switch is booted with factory default configuration.
To ease the configuration of the switch, a "Set Up" facility which
will prompt you with those configuration items that are essential to the operation of the switch is provided.
Would you like to run "Set Up" to configure the switch? [y/n]:
Note: If the default admin login is unsuccessful, or if the administrator Main Menu appears instead, the system configuration has probably been changed from the factory default settings. If desired, return the switch to its factory default configuration.
3. Enter y to begin the initial configuration of the switch, or n to bypass the Setup facility.
© Copyright Lenovo 2016
Chapter 2: Initial Setup
61
Setting the Management Interface Default IP Address
To facilitate switch boot up, the in‐band and out‐of‐band management interfaces are configured with factory default IP addresses. These are as follows:

VLAN 1/ Interface 1: 192.168.49.50/24
If you configure static IP addresses or if DHCP/BOOTP addresses are assigned to these interfaces, the factory default IP addresses will not be applied. By default, DHCP and BOOTP are enabled on the management interfaces.
If you add interface 1 to another VLAN and do not configure any IP address, the factory default IP address will be automatically assigned to the interface. We recommend that you disable the factory default IP address configuration after the switch boot up and configuration is complete. Use the following command: RS G8052(config)# no system default-ip data
62
G8052 Application Guide for ENOS 8.4
Stopping and Restarting Setup Manually
Follow these instructions to manually stop and start the Setup utility.
Stopping Setup
To abort the Setup utility, press <Ctrl‐C> during any Setup question. When you abort Setup, the system will prompt:
Would you like to run from top again? [y/n]
Enter n to abort Setup, or y to restart the Setup program at the beginning.
Restarting Setup
You can restart the Setup utility manually at any time by entering the following command at the administrator prompt:
RS G8052(config)# setup
© Copyright Lenovo 2016
Chapter 2: Initial Setup
63
Setup Part 1: Basic System Configuration
When Setup is started, the system prompts:
"Set Up" will walk you through the configuration of
System Date and Time, Spanning Tree, Port Speed/Mode,
VLANs, and IP interfaces. [type Ctrl­C to abort "Set Up"]
1. Enter y if you will be configuring VLANs. Otherwise enter n.
If you decide not to configure VLANs during this session, you can configure them later using the configuration menus, or by restarting the Setup facility. For more information on configuring VLANs, see the Lenovo Enterprise Network Operating System Application Guide. Next, the Setup utility prompts you to input basic system information.
2. Enter the year of the current date at the prompt:
System Date:
Enter year [2009]:
Enter the four‐digits that represent the year. To keep the current year, press <Enter>.
3. Enter the month of the current system date at the prompt:
System Date:
Enter month [1]:
Enter the month as a number from 1 to 12. To keep the current month, press <Enter>.
4. Enter the day of the current date at the prompt:
Enter day [3]:
Enter the date as a number from 1 to 31. To keep the current day, press <Enter>.
The system displays the date and time settings:
System clock set to 18:55:36 Wed Jan 28, 2009.
5. Enter the hour of the current system time at the prompt:
System Time:
Enter hour in 24­hour format [18]:
Enter the hour as a number from 00 to 23. To keep the current hour, press <Enter>.
6. Enter the minute of the current time at the prompt:
Enter minutes [55]:
64
G8052 Application Guide for ENOS 8.4
Enter the minute as a number from 00 to 59. To keep the current minute, press <Enter>.
7. Enter the seconds of the current time at the prompt:
Enter seconds [37]:
Enter the seconds as a number from 00 to 59. To keep the current second, press <Enter>. The system then displays the date and time settings:
System clock set to 8:55:36 Wed Jan 28, 2009.
8. Turn Spanning Tree Protocol on or off at the prompt:
Spanning Tree:
Current Spanning Tree Group 1 setting: ON
Turn Spanning Tree Group 1 OFF? [y/n]
Enter y to turn off Spanning Tree, or enter n to leave Spanning Tree on.
© Copyright Lenovo 2016
Chapter 2: Initial Setup
65
Setup Part 2: Port Configuration
Note: When configuring port options for your switch, some prompts and options may be different. 1. Select whether you will configure VLANs and VLAN trunk mode/tagging for ports: Port Config:
Will you configure VLANs and VLAN Tagging/Trunk­Mode for ports? [y/n]
If you wish to change settings for VLANs, enter y, or enter n to skip VLAN configuration. Note: The sample screens that appear in this document might differ slightly from the screens displayed by your system. Screen content varies based on the firmware versions and options that are installed.
2. Select the port to configure, or skip port configuration at the prompt: If you wish to change settings for individual ports, enter the number of the port you wish to configure. To skip port configuration, press <Enter> without specifying any port and go to “Setup Part 3: VLANs” on page 68. 3. Configure Gigabit Ethernet port flow parameters.
The system prompts:
Gig Link Configuration:
Port Flow Control:
Current Port EXT1 flow control setting: both
Enter new value ["rx"/"tx"/"both"/"none"]:
Enter rx to enable receive flow control, tx for transmit flow control, both to enable both, or none to turn flow control off for the port. To keep the current setting, press <Enter>.
4. Configure Gigabit Ethernet port autonegotiation mode. If you selected a port that has a Gigabit Ethernet connector, the system prompts:
Port Auto Negotiation:
Current Port autonegotiation: on
Enter new value ["on"/"off"]:
Enter on to enable port autonegotiation, off to disable it, or press <Enter> to keep the current setting. 5. If configuring VLANs, enable or disable VLAN trunk mode/tagging for the port.
If you have selected to configure VLANs back in Part 1, the system prompts:
Port VLAN tagging/trunk mode config (tagged/trunk mode port can be a member of multiple VLANs)
Current VLAN tagging/trunk mode support: disabled
Enter new VLAN tagging/trunk mode support [d/e]:
66
G8052 Application Guide for ENOS 8.4
Enter d to disable VLAN trunk mode/tagging for the port or enter e to enable VLAN tagging for the port. To keep the current setting, press <Enter>.
6. The system prompts you to configure the next port: Enter port (1­52):
When you are through configuring ports, press <Enter> without specifying any port. Otherwise, repeat the steps in this section.
© Copyright Lenovo 2016
Chapter 2: Initial Setup
67
Setup Part 3: VLANs
If you chose to skip VLANs configuration back in Part 2, skip to “Setup Part 4: IP Configuration” on page 69.
1. Select the VLAN to configure, or skip VLAN configuration at the prompt:
VLAN Config:
Enter VLAN number from 2 to 4094, NULL at end:
If you wish to change settings for individual VLANs, enter the number of the VLAN you wish to configure. To skip VLAN configuration, press <Enter> without typing a VLAN number and go to “Setup Part 4: IP Configuration” on page 69.
2. Enter the new VLAN name at the prompt:
Current VLAN name: VLAN 2
Enter new VLAN name:
Entering a new VLAN name is optional. To use the pending new VLAN name, press <Enter>. 3. Enter the VLAN port numbers: Define Ports in VLAN:
Current VLAN 2: empty
Enter ports one per line, NULL at end:
Enter each port, by port number or port alias, and confirm placement of the port into this VLAN. When you are finished adding ports to this VLAN, press <Enter> without specifying any port. 4. Configure Spanning Tree Group membership for the VLAN: Spanning Tree Group membership:
Enter new Spanning Tree Group index [1­128]:
5. The system prompts you to configure the next VLAN: VLAN Config:
Enter VLAN number from 2 to 4094, NULL at end:
Repeat the steps in this section until all VLANs have been configured. When all VLANs have been configured, press <Enter> without specifying any VLAN. 68
G8052 Application Guide for ENOS 8.4
Setup Part 4: IP Configuration
The system prompts for IPv4 parameters.
Although the switch supports both IPv4 and IPv6 networks, the Setup utility permits only IPv4 configuration. For IPv6 configuration, see Chapter 24, “Internet Protocol Version 6.”
IP Interfaces
IP interfaces are used for defining the networks to which the switch belongs.
Up to 128 IP interfaces can be configured on the RackSwitch G8052 (G8052). The IP address assigned to each IP interface provides the switch with an IP presence on your network. No two IP interfaces can be on the same IP network. The interfaces can be used for connecting to the switch for remote configuration, and for routing between subnets and VLANs (if used).
1. Select the IP interface to configure, or skip interface configuration at the prompt:
IP Config:
IP interfaces:
Enter interface number: (1­128) If you wish to configure individual IP interfaces, enter the number of the IP interface you wish to configure. To skip IP interface configuration, press <Enter> without typing an interface number and go to “Default Gateways” on page 71. 2. For the specified IP interface, enter the IP address in IPv4 dotted decimal notation:
Current IP address: 0.0.0.0
Enter new IP address:
To keep the current setting, press <Enter>.
3. At the prompt, enter the IPv4 subnet mask in dotted decimal notation:
Current subnet mask: 0.0.0.0
Enter new subnet mask:
To keep the current setting, press <Enter>.If configuring VLANs, specify a VLAN for the interface.
The following prompt appears if you selected to configure VLANs back in Part 1:
Current VLAN: 1
Enter new VLAN [1­4094]:
Enter the number for the VLAN to which the interface belongs, or press <Enter> without specifying a VLAN number to accept the current setting.
© Copyright Lenovo 2016
Chapter 2: Initial Setup
69
4. At the prompt, enter y to enable the IP interface, or n to leave it disabled:
Enable IP interface? [y/n]
5. The system prompts you to configure another interface:
Enter interface number: (1­128) Repeat the steps in this section until all IP interfaces have been configured. When all interfaces have been configured, press <Enter> without specifying any interface number.
Loopback Interfaces
A loopback interface provides an IP address, but is not otherwise associated with a physical port or network entity. Essentially, it is a virtual interface that is perceived as being “always available” for higher‐layer protocols to use and advertise to the network, regardless of other connectivity.
Loopback interfaces improve switch access, increase reliability, security, and provide greater flexibility in Layer 3 network designs. They can be used for many different purposes, but are most commonly for management IP addresses, router IDs for various protocols, and persistent peer IDs for neighbor relationships.
In Enterprise NOS 8.4, loopback interfaces have been expanded for use with routing protocols such as OSPF, PIM, and BGP. Loopback interfaces can also be specified as the source IP address for syslog, SNMP, RADIUS, TACACS+, NTP, and router IDs.
Loopback interfaces must be configured before they can be used in other features. Up to five loopback interfaces are currently supported. They can be configured using the following commands:
RS G8052(config)# interface loopback <1‐5>
RS G8052(config­ip­loopback)# [no] ip address <IPv4 address> <mask> enable
RS G8052(config­ip­loopback)# exit
Using Loopback Interfaces for Source IP Addresses
The switch can use loopback interfaces to set the source IP addresses for a variety of protocols. This assists in server security, as the server for each protocol can be configured to accept protocol packets only from the expected loopback address block. It may also make is easier to locate or process protocol information, since packets have the source IP address of the loopback interface, rather than numerous egress interfaces.
Configured loopback interfaces can be applied to the following protocols:

Syslogs
RS G8052(config)# logging source­interface loopback <1‐5>

SNMP traps
RS G8052(config)# snmp­server trap­source loopback <1‐5>
70
G8052 Application Guide for ENOS 8.4

RADIUS
RS G8052(config)# ip radius source­interface loopback <1‐5>

TACACS+
RS G8052(config)# ip tacacs source­interface loopback <1‐5>

NTP
RS G8052(config)# ntp source loopback <1‐5>
Loopback Interface Limitations


ARP is not supported. Loopback interfaces will ignore ARP requests.
Loopback interfaces cannot be assigned to a VLAN.
Default Gateways
To set up a default gateway:
1. At the prompt, select an IP default gateway for configuration, or skip default gateway configuration:
IP default gateways:
Enter default gateway number: (1­4) Enter the number for the IP default gateway to be configured. To skip default gateway configuration, press <Enter> without typing a gateway number and go to “IP Routing” on page 71.
2. At the prompt, enter the IPv4 address for the selected default gateway:
Current IP address: 0.0.0.0
Enter new IP address:
Enter the IPv4 address in dotted decimal notation, or press <Enter> without specifying an address to accept the current setting.
3. At the prompt, enter y to enable the default gateway, or n to leave it disabled:
Enable default gateway? [y/n]
4. The system prompts you to configure another default gateway:
Enter default gateway number: (1­4) Repeat the steps in this section until all default gateways have been configured. When all default gateways have been configured, press <Enter> without specifying any number. IP Routing
When IP interfaces are configured for the various IP subnets attached to your switch, IP routing between them can be performed entirely within the switch. This eliminates the need to send inter‐subnet communication to an external router © Copyright Lenovo 2016
Chapter 2: Initial Setup
71
device. Routing on more complex networks, where subnets may not have a direct presence on the G8052, can be accomplished through configuring static routes or by letting the switch learn routes dynamically.
This part of the Setup program prompts you to configure the various routing parameters.
At the prompt, enable or disable forwarding for IP Routing:
Enable IP forwarding? [y/n]
Enter y to enable IP forwarding. To disable IP forwarding, enter n. To keep the current setting, press <Enter>.
72
G8052 Application Guide for ENOS 8.4
Setup Part 5: Final Steps
1. When prompted, decide whether to restart Setup or continue:
Would you like to run from top again? [y/n]
Enter y to restart the Setup utility from the beginning, or n to continue.
2. When prompted, decide whether you wish to review the configuration changes:
Review the changes made? [y/n]
Enter y to review the changes made during this session of the Setup utility. Enter n to continue without reviewing the changes. We recommend that you review the changes.
3. Next, decide whether to apply the changes at the prompt:
Apply the changes? [y/n]
Enter y to apply the changes, or n to continue without applying. Changes are normally applied.
4. At the prompt, decide whether to make the changes permanent:
Save changes to flash? [y/n]
Enter y to save the changes to flash. Enter n to continue without saving the changes. Changes are normally saved at this point.
5. If you do not apply or save the changes, the system prompts whether to abort them:
Abort all changes? [y/n]
Enter y to discard the changes. Enter n to return to the “Apply the changes?” prompt.
Note: After initial configuration is complete, it is recommended that you change the default passwords.
© Copyright Lenovo 2016
Chapter 2: Initial Setup
73
Optional Setup for Telnet Support
Note: This step is optional. Perform this procedure only if you are planning on connecting to the G8052 through a remote Telnet connection.
Telnet is enabled by default. To change the setting, use the following command: RS G8052(config)# no access telnet 74
G8052 Application Guide for ENOS 8.4
Chapter 3. Switch Software Management
The switch software image is the executable code running on the G8052. A version of the image comes pre‐installed on the device. As new versions of the image are released, you can upgrade the software running on your switch. To get the latest version of software supported for your G8052, go to the following website:
http://www.lenovo.com/support/
To determine the software version currently used on the switch, use the following switch command: RS G8052# show boot
The typical upgrade process for the software image consists of the following steps:

Load a new software image and boot image onto an FTP, SFTP or TFTP server on your network.

Transfer the new images to your switch. 
Specify the new software image as the one which will be loaded into switch memory the next time a switch reset occurs.

Reset the switch.
For instructions on the typical upgrade process using the ENOS ISCLI, USB, or BBI, see “Loading New Software to Your Switch” on page 76.
CAUTION:
Although the typical upgrade process is all that is necessary in most cases, upgrading from (or reverting to) some versions of Lenovo Enterprise Network Operating System requires special steps prior to or after the software installation process. Please be sure to follow all applicable instructions in the release notes document for the specific software release to ensure that your switch continues to operate as expected after installing new software.
© Copyright Lenovo 2016
75
Loading New Software to Your Switch
The G8052 can store up to two different switch software images (called image1 and image2) as well as special boot software (called boot). When you load new software, you must specify where it is placed: either into image1, image2, or boot. For example, if your active image is currently loaded into image1, you would probably load the new image software into image2. This lets you test the new software and reload the original active image (stored in image1), if needed. CAUTION:
When you upgrade the switch software image, always load the new boot image and the new software image before you reset the switch. If you do not load a new boot image, your switch might not boot properly (To recover, see “Recovering from a Failed Software Upgrade” on page 80). To load a new software image to your switch, you will need the following:

The image and boot software loaded on an FTP, SFTP or TFTP server on your net‐
work.
Note: Be sure to download both the new boot file and the new image file.

The hostname or IP address of the FTP, SFTP or TFTP server
Note: The DNS parameters must be configured if specifying hostnames.

The name of the new system image.
When the software requirements are met, use one of the following procedures to download the new software to your switch. You can use the ISCLI, USB, or the BBI to download and activate new software.
Loading Software via the ISCLI
1. In Privileged EXEC mode, enter the following command: Router# copy {tftp|ftp|sftp} {image1|image2|boot­image}
2. Enter the hostname or IP address of the FTP, SFTP or TFTP server.
Address or name of remote host: <name or IP address>
3. Enter the name of the new software file on the server.
Source file name: <filename>
The exact form of the name will vary by server. However, the file location is normally relative to the FTP, SFTP or TFTP directory (for example, tftpboot). 4. If required by the FTP, SFTP or TFTP server, enter the appropriate username and password.
76
G8052 Application Guide for ENOS 8.4
5. The switch will prompt you to confirm your request.
Once confirmed, the software will begin loading into the switch.
6. When loading is complete, use the following commands to enter Global Configuration mode to select which software image (image1 or image2) you want to run in switch memory for the next reboot: Router#
configure terminal
boot image {image1|image2} Router(config)#
The system will then verify which image is set to be loaded at the next reset: Next boot will use switch software image1 instead of image2.
7. Reboot the switch to run the new software:
Router(config)# reload
The system prompts you to confirm your request. Once confirmed, the switch will reboot to use the new software.
Loading Software via BBI
You can use the Browser‐Based Interface to load software onto the G8052. The software image to load can reside in one of the following locations: 
FTP server

TFTP server

SFTP server

Local computer
After you log onto the BBI, perform the following steps to load a software image: 1. Click the Configure context tab in the toolbar. 2. In the Navigation Window, select System > Config/Image Control. The Switch Image and Configuration Management page appears.
3. If you are loading software from your computer (HTTP client), skip this step and go to the next. Otherwise, if you are loading software from an FTP, SFTP, or TFTP server, enter the server’s information in the FTP, SFTP, or TFTP Settings section.
4. In the Image Settings section, select the image version you want to replace (Image for Transfer). 
If you are loading software from an FTP, SFTP, or TFTP server, enter the file name and click Get Image. 
If you are loading software from your computer, click Browse.

In the File Upload Dialog, select the file and click OK. Then click Download via
Browser. Once the image has loaded, the page refreshes to show the new software.
© Copyright Lenovo 2016
Chapter 3: Switch Software Management
77
USB Options
You can insert a USB drive into the USB port on the G8052 and use it to work with switch image and configuration files. You can boot the switch using files located on the USB drive, or copy files to and from the USB drive. To safely remove the USB drive, first use the following command to un‐mount the USB file system: system usb­eject
Command mode: Global configuration
USB Boot
USB Boot allows you to boot the switch with a software image file, boot file, or configuration file that resides on a USB drive inserted into the USB port. Use the following command to enable or disable USB Boot: [no] boot usbboot enable
Command mode: Global configuration
When enabled, when the switch is reset/reloaded, it checks the USB port. If a USB drive is inserted into the port, the switch checks the root directory on the USB drive for software and image files. If a valid file is present, the switch loads the file and boots using the file. Note: The following file types are supported: FAT32, NTFS (read‐only), EXT2, and EXT3. The following list describes the valid file names, and describes the switch behavior when it recognizes them. The file names must be exactly as shown, or the switch will not recognize them. 78

RSG8052_Boot.img
The switch replaces the current boot image with the new image, and boots with the new image.

RSG8052_OS.img
The switch boots with the new software image. The existing images are not affected. 
RSG8052_replace1_OS.img
The switch replaces the current software image1 with the new image, and boots with the new image. RSG8052_replace1_OS.img takes precedence over RSG8052_OS.img.

RSG8052_replace2_OS.img
The switch replaces the current software image2 with the new image, and boots with the new image. RSG8052_replace2_OS.img takes precedence over RSG8052_OS.img.

RSG8052.cfg
The switch boots with the new configuration file. The existing configuration files (active and backup) are not affected. G8052 Application Guide for ENOS 8.4

RSG8052_replace.cfg
The switch replaces the active configuration file with the new file, and boots with the new file. This file takes precedence over any other configuration files that may be present on the USB drive. If more than one valid file is present, the switch loads all valid files and boots with them. For example, you may simultaneously load a new boot file, image file, and configuration file from the USB drive. The switch ignores any files that do not match the valid file names or that have the wrong format. USB Copy
If a USB drive is inserted into the USB port, you can copy files from the switch to the USB drive, or from the USB drive to the switch. USB Copy is available only for software image 1 and the active configuration. Copy to USB
Use the following command to copy a file from the switch to the USB drive (Privileged EXEC mode): usbcopy tousb <filename> {boot|image1|active|syslog|crashdump}
In this example, the active configuration file is copied to a directory on the USB drive: G8052(config)# usbcopy tousb a_folder/myconfig.cfg active
Copy from USB
Use the following command to copy a file from the USB drive to the switch: usbcopy fromusb <filename> {boot|image1|active}
In this example, the active configuration file is copied from a directory on the USB drive: G8052(config)# usbcopy fromusb a_folder/myconfig.cfg active
The new file replaces the current file. Note: Do not use two consecutive dot characters ( .. ). Do not use a slash character ( / ) to begin a filename. © Copyright Lenovo 2016
Chapter 3: Switch Software Management
79
The Boot Management Menu
The Boot Management menu allows you to switch the software image, reset the switch to factory defaults, or to recover from a failed software download. You can interrupt the boot process and enter the Boot Management menu from the serial console port. When the system displays Memory Test, press <Shift B>. The Boot Management menu appears. Resetting the System ...
Memory Test ................................
Boot Management Menu
I ­ Change booting image
C ­ Change configuration block
R ­ Boot in recovery mode (tftp and xmodem download of images to recover switch)
Q ­ Reboot
E ­ Exit
Please choose your menu option: I
Current boot image is 1. Enter image to boot: 1 or 2: 2
Booting from image 2
The Boot Management menu allows you to perform the following actions: 
To change the booting image, press I and follow the screen prompts. 
To change the configuration block, press C, and follow the screen prompts. 
To perform a TFTP/XModem download, press R and follow the screen prompts.

To reboot the switch, press Q. The booting process restarts.

To exit the Boot Management menu, press E. The booting process continues. Recovering from a Failed Software Upgrade
Use the following procedure to recover from a failed software upgrade. 1. Connect a PC to the serial port of the switch. 2. Open a terminal emulator program that supports XModem Download (for example, HyperTerminal, CRT, PuTTY) and select the following serial port characteristics:
80

Speed: 9600 bps

Data Bits: 8

Stop Bits: 1

Parity: None

Flow Control: None
G8052 Application Guide for ENOS 8.4
3. To access the Boot Management menu you must interrupt the boot process from the Console port. Boot the G8052, and when the system begins displaying Memory Test progress (a series of dots), press <Shift B>. The boot managment menu appears: Resetting the System ...
Memory Test ................................
Boot Management Menu
I ­ Change booting image
C ­ Change configuration block
R ­ Boot in recovery mode (tftp and xmodem download of images to recover switch)
Q ­ Reboot
E ­ Exit
Please choose your menu option:
4. Select R for Boot in recovery mode. The following appears: Entering Rescue Mode.
Please select one of the following options:
T) Configure networking and tftp download an image
X) Use xmodem 1K to serial download an image
R) Reboot
E) Exit
© Copyright Lenovo 2016

If you choose option X (Xmodem serial download), go to Step 5.

If you choose option T (TFTP download), go to Step 6.
Chapter 3: Switch Software Management
81
5. Xmodem download: When you see the following message, change the Serial Port characteristics to 115200 bps: Change the baud rate to 115200 bps and hit the <ENTER> key before
initiating the download.
a. Press <Enter> to set the system into download accept mode. When the readiness meter displays (a series of “C” characters), start XModem on your terminal emulator. b. When you see the following message, change the Serial Port characteristics to 9600 bps: Change the baud rate back to 9600 bps, hit the <ESC> key.
c. When you see the following prompt, enter the image number where you want to install the new software and press <Enter>: Install image as image 1 or 2 (hit return to just boot image): 1
d. The following message is displayed when the image download is complete. Continue to step 7. Entering Rescue Mode.
Please select one of the following options:
T) Configure networking and tftp download an image
X) Use xmodem 1K to serial download an image
R) Reboot
E) Exit
Option?:
82
G8052 Application Guide for ENOS 8.4
6. TFTP download: The switch prompts you to enter the following information:
Performing TFTP rescue. Please answer the following questions (enter 'q' to quit):
IP addr :
Server addr:
Netmask :
Gateway :
Image Filename:
a. Enter the required information and press <Enter>.
b. You will see a display similar to the following: Host IP : 10.10.98.110
Server IP : 10.10.98.100
Netmask : 255.255.255.0
Broadcast : 10.10.98.255
Gateway : 10.10.98.254
Installing image G8052­8.4.1.0_OS.img from TFTP server 10.10.98.100
c. When you see the following prompt, enter the image number and press <Enter>: Install image as image 1 or 2 (hit return to just boot image): 1
d. The following message is displayed when the image download is complete. Continue to step 7. Installing image as image1...
Image1 updated successfully
Please select one of the following options:
T) Configure networking and tftp download an image
X) Use xmodem 1K to serial download an image
R) Reboot
E) Exit
7. Image recovery is complete. Perform one of the following steps:

Press r to reboot the switch.

Press e to exit the Boot Management menu

Press the Escape key (<Esc>) to re‐display the Boot Management menu.
Recovering from a Failed Boot Image
Use the following procedure to recover from a failed boot image upgrade.
1. Connect a PC to the serial port of the switch.
2. Open a terminal emulator program that supports Xmodem download (for example, HyperTerminal, CRT, PuTTY) and select the following serial port characteristics:
© Copyright Lenovo 2016

Speed: 9600 bps

Data Bits: 8

Stop Bits: 1
Chapter 3: Switch Software Management
83

Parity: None

Flow Control: None
3. Boot the switch and access the Boot Management menu by pressing <Shift B> while the Memory Test is in progress and the dots are being displayed.
4. Select X for Xmodem download. The following appears: Perform xmodem download
To download an image use 1K Xmodem at 115200 bps.
5. When you see the following message, change the Serial Port characteristics to 115200 bps: Change the baud rate to 115200 bps and hit the <ENTER> key before
initiating the download.
a. Press <Enter> to set the system into download accept mode. When the readiness meter displays (a series of “C” characters), start Xmodem on your terminal emulator.You will see a display similar to the following: Extracting images ... Do *NOT* power cycle the switch.
**** RAMDISK ****
Un­Protected 38 sectors
Erasing Flash...
...................................... done
Erased 38 sectors
Writing to Flash...9....8....7....6....5....4....3....2....1....done
Protected 38 sectors
**** KERNEL ****
Un­Protected 24 sectors
Erasing Flash...
........................ done
Erased 24 sectors
Writing to Flash...9....8....7....6....5....4....3....2....1....
b. When you see the following message, change the Serial Port characteristics to 9600 bps: Change the baud rate back to 9600 bps, hit the <ESC> key.
Boot image recovery is complete.
84
G8052 Application Guide for ENOS 8.4
Part 2: Securing the Switch
© Copyright Lenovo 2016
85
86
G8052 Application Guide for ENOS 8.4
Chapter 4. Securing Administration
Secure switch management is needed for environments that perform significant management functions across the Internet. Common functions for secured management are described in the following sections: 
“Secure Shell and Secure Copy” on page 88

“End User Access Control” on page 93
Note: SNMP read and write functions are enabled by default. For best security practices, if SNMP is not needed for your network, it is recommended that you disable these functions prior to connecting the switch to the network (see Chapter 36, “Simple Network Management Protocol).
© Copyright Lenovo 2016
87
Secure Shell and Secure Copy
Because using Telnet does not provide a secure connection for managing a G8052, Secure Shell (SSH) and Secure Copy (SCP) features have been included for G8052 management. SSH and SCP use secure tunnels to encrypt and secure messages between a remote administrator and the switch.
SSH is a protocol that enables remote administrators to log securely into the G8052 over a network to execute management commands.
SCP is typically used to copy files securely from one machine to another. SCP uses SSH for encryption of data on the network. On a G8052, SCP is used to download and upload the switch configuration via secure channels.
Although SSH and SCP are disabled by default, enabling and using these features provides the following benefits:

Identifying the administrator using Name/Password

Authentication of remote administrators

Authorization of remote administrators

Determining the permitted actions and customizing service for individual administrators

Encryption of management messages

Encrypting messages between the remote administrator and switch

Secure copy support
Lenovo Enterprise Network Operating System implements the SSH version 2.0 standard and is confirmed to work with SSH version 2.0‐compliant clients such as the following:

OpenSSH_5.4p1 for Linux

Secure CRT Version 5.0.2 (build 1021)

Putty SSH release 0.60 Configuring SSH/SCP Features on the Switch
SSH and SCP features are disabled by default. To change the SSH/SCP settings, using the following procedures.
Note: To use SCP, you must first enable SSH.
To Enable or Disable the SSH Feature
Begin a Telnet session from the console port and enter the following command:
RS G8052(config)# [no] ssh enable
88
G8052 Application Guide for ENOS 8.4
To Enable or Disable SCP Apply and Save
Enter the following command from the switch CLI to enable the SCP putcfg_apply and putcfg_apply_save commands:
RS G8052(config)# [no] ssh scp­enable
Configuring the SCP Administrator Password
To configure the SCP‐only administrator password, enter the following command (the default password is admin):
RS G8052(config)# [no] ssh scp­password
Changing SCP­only Administrator password; validation required...
Enter current administrator password: <password>
Enter new SCP­only administrator password: <new password>
Re­enter new SCP­only administrator password: <new password>
New SCP­only administrator password accepted.
Using SSH and SCP Client Commands
This section shows the format for using some client commands. The following examples use 205.178.15.157 as the IP address of a sample switch.
To Log Into the Switch
Syntax:
>> ssh [­4|­6] <switch IP address>
‐or‐
>> ssh [­4|­6] <login name>@<switch IP address>
Note: The ­4 option (the default) specifies that an IPv4 switch address will be used. The ­6 option specifies IPv6.
Example:
>> ssh [email protected]
To Copy the Switch Configuration File to the SCP Host
Syntax:
>> scp [­4|­6] <username>@<switch IP address>:getcfg <local filename> Example:
>> scp [email protected]:getcfg ad4.cfg
© Copyright Lenovo 2016
Chapter 4: Securing Administration
89
To Load a Switch Configuration File from the SCP Host
Syntax:
>> scp [­4|­6] <local filename> <username>@<switch IP address>:putcfg
Example:
>> scp ad4.cfg [email protected]:putcfg
To Apply and Save the Configuration
When loading a configuration file to the switch, the apply and save commands are still required for the configuration commands to take effect. The apply and save commands may be entered manually on the switch, or by using SCP commands.
Syntax:
>> scp [­4|­6] <local filename> <username>@<switch IP address>:putcfg_apply
>> scp [­4|­6] <local filename> <username>@<switch IP address>:putcfg_apply_save
Example:
>> scp ad4.cfg [email protected]:putcfg_apply
>> scp ad4.cfg [email protected]:putcfg_apply_save

The CLI diff command is automatically executed at the end of putcfg to notify the remote client of the difference between the new and the current configurations.

putcfg_apply runs the apply command after the putcfg is done.

putcfg_apply_save saves the new configuration to the flash after putcfg_apply is done.

The putcfg_apply and putcfg_apply_save commands are provided because extra apply and save commands are usually required after a putcfg; however, an SCP session is not in an interactive mode.
To Copy the Switch Image and Boot Files to the SCP Host
Syntax:
>> scp [­4|­6] <username>@<switch IP address>:getimg1 <local filename> >> scp [­4|­6] <username>@<switch IP address>:getimg2 <local filename> >> scp [­4|­6] <username>@<switch IP address>:getboot <local filename> Example:
>> scp [email protected]:getimg1 6.1.0_os.img
90
G8052 Application Guide for ENOS 8.4
To Load Switch Configuration Files from the SCP Host
Syntax:
>> scp [­4|­6] <local filename> <username>@<switch IP address>:putimg1
>> scp [­4|­6] <local filename> <username>@<switch IP address>:putimg2
>> scp [­4|­6] <local filename> <username>@<switch IP address>:putboot
Example:
>> scp 6.1.0_os.img [email protected]:putimg1
SSH and SCP Encryption of Management Messages
The following encryption and authentication methods are supported for SSH and SCP:

Server Host Authentication: Client RSA authenticates the switch at the beginning of every connection

Key Exchange: RSA

Encryption:
3DES‐CBC, DES

User Authentication:
Local password authentication, RADIUS
Generating RSA Host Key for SSH Access
To support the SSH host feature, an RSA host key is required. The host key is 2048 bits and is used to identify the G8052.
To configure RSA host key, first connect to the G8052 through the console port (commands are not available via external Telnet connection), and enter the following command to generate it manually.
RS G8052(config)# ssh generate­host­key
When the switch reboots, it will retrieve the host key from the FLASH memory.
Note: The switch will perform only one session of key/cipher generation at a time. Thus, an SSH/SCP client will not be able to log in if the switch is performing key generation at that time. Also, key generation will fail if an SSH/SCP client is logging in at that time.
SSH/SCP Integration with Radius Authentication
SSH/SCP is integrated with RADIUS authentication. After the RADIUS server is enabled on the switch, all subsequent SSH authentication requests will be redirected to the specified RADIUS servers for authentication. The redirection is transparent to the SSH clients.
© Copyright Lenovo 2016
Chapter 4: Securing Administration
91
SSH/SCP Integration with TACACS+ Authentication
SSH/SCP is integrated with TACACS+ authentication. After the TACACS+ server is enabled on the switch, all subsequent SSH authentication requests will be redirected to the specified TACACS+ servers for authentication. The redirection is transparent to the SSH clients.
92
G8052 Application Guide for ENOS 8.4
End User Access Control
Enterprise NOS allows an administrator to define end user accounts that permit end users to perform operation tasks via the switch CLI commands. Once end user accounts are configured and enabled, the switch requires username/password authentication. For example, an administrator can assign a user, who can then log into the switch and perform operational commands (effective only until the next switch reboot). Considerations for Configuring End User Accounts
Note the following considerations when you configure end user accounts:

A maximum of 20 user IDs are supported on the switch.

ENOS supports end user support for console, Telnet, BBI, and SSHv2 access to the switch. 
If RADIUS authentication is used, the user password on the Radius server will override the user password on the G8052. Also note that the password change command only modifies only the user password on the switch and has no effect on the user password on the Radius server. Radius authentication and user password cannot be used concurrently to access the switch. 
Passwords for end users can be up to 128 characters in length for TACACS, RADIUS, Telnet, SSH, Console, and Web access.
Strong Passwords
The administrator can require use of Strong Passwords for users to access the G8052. Strong Passwords enhance security because they make password guessing more difficult.
The following rules apply when Strong Passwords are enabled:

Minimum length: 8 characters; maximum length: 64 characters

Must contain at least one uppercase alphabet

Must contain at least one lowercase alphabet

Must contain at least one number

Must contain at least one special character: Supported special characters: ! “ # % & ‘ ( ) ; < = >> ? [\] * + , ‐ . / : ^ _ { | } ~

Cannot be same as the username
When strong password is enabled, users can still access the switch using the old password but will be advised to change to a strong password at log‐in. Strong password requirement can be enabled using the following command: RS G8052(config)# access user strong­password enable
© Copyright Lenovo 2016
Chapter 4: Securing Administration
93
The administrator can choose the number of days allowed before each password expires. When a strong password expires, the user is allowed to log in one last time (last time) to change the password. A warning provides advance notice for users to change the password.
User Access Control
The end‐user access control commands allow you to configure end‐user accounts.
Setting up User IDs
Up to 20 user IDs can be configured. Use the following commands to define any user name and set the user password at the resulting prompts: RS G8052(config)# access user 1 name <1‐64 characters>
RS G8052(config)# access user 1 password
Changing user1 password; validation required:
Enter current admin password: <current administrator password>
Enter new user1 password: <new user password>
Re­enter new user1 password: <new user password>
New user1 password accepted. Defining a User’s Access Level
The end user is by default assigned to the user access level (also known as class of service, or COS). COS for all user accounts have global access to all resources except for User COS, which has access to view only resources that the user owns. For more information, see Table 8 on page 103.
To change the user’s level, select one of the following options: RS G8052(config)# access user 1 level {user|operator|administrator} Validating a User’s Configuration
RS G8052# show access user uid 1
Enabling or Disabling a User
An end user account must be enabled before the switch recognizes and permits login under the account. Once enabled, the switch requires any user to enter both username and password. RS G8052(config)# [no] access user 1 enable Locking Accounts
To protect the switch from unauthorized access, the account lockout feature can be enabled. By default, account lockout is disabled. To enable this feature, ensure the strong password feature is enabled (See “Strong Passwords” on page 93). Then use the following command: RS G8052(config)# access user strong­password lockout
94
G8052 Application Guide for ENOS 8.4
After multiple failed login attempts, the switch locks the user account if lockout has been enabled on the switch. Re-Enabling Locked Accounts
The administrator can re‐enable a locked account by reloading the switch or by using the following command: RS G8052(config)# access user strong­password clear local user lockout username <user name>
However, the above command cannot be used to re‐enable an account disabled by the administrator. To re‐enable all locked accounts, use the following command: RS G8052(config)# access user strong­password clear local user lockout all
Listing Current Users
The following command displays defined user accounts and whether or not each user is currently logged into the switch. RS G8052# show access user
Usernames:
user ­ Enabled ­ offline
oper ­ Disabled ­ offline
admin ­ Always Enabled ­ online 1 session
Current User ID table:
1: name jane , ena, cos user , password valid, online 1 session
2: name john , ena, cos user , password valid, online 2 sessions
Logging into an End User Account
Once an end user account is configured and enabled, the user can login to the switch using the username/password combination. The level of switch access is determined by the COS established for the end user account. Password Fix-Up Mode
Password Fix‐Up Mode enables admin user account recovery if administrator access is lost. A user must connect to the switch over the serial console and log in using the “ForgetMe!” password. This enables the admin account if disabled and a new administrator password can be entered.
To disable the Password Fix‐Up functionality, use the following command:
RS G8052(config)# no access user password­recovery
© Copyright Lenovo 2016
Chapter 4: Securing Administration
95
96
G8052 Application Guide for ENOS 8.4
Chapter 5. Authentication & Authorization Protocols
Secure switch management is needed for environments that perform significant management functions across the Internet. The following are some of the functions for secured IPv4 management and device access:

“RADIUS Authentication and Authorization” on page 98

“TACACS+ Authentication” on page 102

“LDAP Authentication and Authorization” on page 106
Note: Lenovo Enterprise Network Operating System 8.4 does not support IPv6 for RADIUS, TACACS+ or LDAP.
© Copyright Lenovo 2016
97
RADIUS Authentication and Authorization
Enterprise NOS supports the RADIUS (Remote Authentication Dial‐in User Service) method to authenticate and authorize remote administrators for managing the switch. This method is based on a client/server model. The Remote Access Server (RAS)—the switch—is a client to the back‐end database server. A remote user (the remote administrator) interacts only with the RAS, not the back‐end server and database. RADIUS authentication consists of the following components:
A protocol with a frame format that utilizes UDP over IP (based on RFC 2138 and 2866)
 A centralized server that stores all the user authorization information
 A client: in this case, the switch

The G8052—acting as the RADIUS client—communicates to the RADIUS server to authenticate and authorize a remote administrator using the protocol definitions specified in RFC 2138 and 2866. Transactions between the client and the RADIUS server are authenticated using a shared key that is not sent over the network. In addition, the remote administrator passwords are sent encrypted between the RADIUS client (the switch) and the back‐end RADIUS server.
How RADIUS Authentication Works
The RADIUS authentication process follows these steps:
1. A remote administrator connects to the switch and provides a user name and password.
2. Using Authentication/Authorization protocol, the switch sends request to authentication server.
3. The authentication server checks the request against the user ID database.
4. Using RADIUS protocol, the authentication server instructs the switch to grant or deny administrative access.
Configuring RADIUS on the Switch
Use the following procedure to configure Radius authentication on your switch. 1. Configure the IPv4 addresses of the Primary and Secondary RADIUS servers, and enable RADIUS authentication. RS G8052(config)# radius­server primary­host 10.10.1.1
RS G8052(config)# radius­server secondary­host 10.10.1.2
RS G8052(config)# radius­server enable
Note: You can use a configured loopback address as the source address so the RADIUS server accepts requests only from the expected loopback address block. Use the following command to specify the loopback interface:
RS G8052(config)# ip radius source­interface loopback <1‐5>
98
G8052 Application Guide for ENOS 8.4
2. Configure the RADIUS secret. RS G8052(config)# radius­server primary­host 10.10.1.1 key <1‐32 character secret>
RS G8052(config)# radius­server secondary­host 10.10.1.2 key <1‐32 character secret>
3. If desired, you may change the default UDP port number used to listen to RADIUS. The well‐known port for RADIUS is 1812. RS G8052(config)# radius­server port <UDP port number>
4. Configure the number retry attempts for contacting the RADIUS server, and the timeout period. RS G8052(config)# radius­server retransmit 3
RS G8052(config)# radius­server timeout 5
© Copyright Lenovo 2016
Chapter 5: Authentication & Authorization Protocols
99
RADIUS Authentication Features in Enterprise NOS
ENOS supports the following RADIUS authentication features:

Supports RADIUS client on the switch, based on the protocol definitions in RFC 2138 and RFC 2866.

Allows RADIUS secret password up to 32 bytes and less than 16 octets.

Supports secondary authentication server so that when the primary authentication server is unreachable, the switch can send client authentication requests to the secondary authentication server. Use the following command to show the currently active RADIUS authentication server: RS G8052# show radius­server

Supports user‐configurable RADIUS server retry and time‐out values:

Time‐out value = 1‐10 seconds

Retries = 1‐3
The switch will time out if it does not receive a response from the RADIUS server in 1‐3 retries. The switch will also automatically retry connecting to the RADIUS server before it declares the server down.

Allows network administrator to define privileges for one or more specific users to access the switch at the RADIUS user database.
Switch User Accounts
The user accounts listed in Table 6 can be defined in the RADIUS server dictionary file. Table 6. User Access Levels
100
User Account
Description and Tasks Performed
Password
User
The User has no direct responsibility for switch management. They can view all switch status information and statistics but cannot make any configuration changes to the switch.
user
Operator
The Operator manages all functions of the switch. The Operator can reset ports. oper
Administrator
The super‐user Administrator has complete access admin to all commands, information, and configuration commands on the switch, including the ability to change both the user and administrator passwords.
G8052 Application Guide for ENOS 8.4
RADIUS Attributes for Enterprise NOS User Privileges
When the user logs in, the switch authenticates his/her level of access by sending the RADIUS access request, that is, the client authentication request, to the RADIUS authentication server.
If the remote user is successfully authenticated by the authentication server, the switch will verify the privileges of the remote user and authorize the appropriate access. The administrator has two options: to allow backdoor access via Telnet, SSH, HTTP, or HTTPS; to allow secure backdoor access via Telnet, SSH, or BBI. Backdoor and secure backdoor provides access to the switch when the RADIUS servers cannot be reached.
The default G8052 setting for backdoor and secure backdoor access is disabled. Backdoor and secure backdoor access is always enabled on the console port.
Irrespective of backdoor/secure backdoor being enabled or not, you can always access the switch via the console port by using noradius as radius username. You can then enter the username and password configured on the switch. If you are trying to connect via SSH/Telnet/HTTP/HTTPS (not console port), there are two possibilities: 
Backdoor is enabled: The switch acts like it is connecting via console.

Secure backdoor is enabled: You must enter the username: noradius. The switch checks if RADIUS server is reachable. If it is reachable, then you must authenticate via remote authentication server. Only if RADIUS server is not reachable, you will be prompted for local user/password to be authenticated against these local credentials.
All user privileges, other than those assigned to the Administrator, have to be defined in the RADIUS dictionary. RADIUS attribute 6 which is built into all RADIUS servers defines the administrator. The file name of the dictionary is RADIUS vendor‐dependent. The following RADIUS attributes are defined for G8052 user privileges levels: Table 7. Enterprise NOS‐proprietary Attributes for RADIUS
© Copyright Lenovo 2016
User Name/Access
User-Service-Type
Value
User
Vendor‐supplied
255
Operator
Vendor‐supplied
252
Admin
Vendor‐supplied
6
Chapter 5: Authentication & Authorization Protocols
101
TACACS+ Authentication
ENOS supports authentication and authorization with networks using the Cisco Systems TACACS+ protocol. The G8052 functions as the Network Access Server (NAS) by interacting with the remote client and initiating authentication and authorization sessions with the TACACS+ access server. The remote user is defined as someone requiring management access to the G8052 through a data port. TACACS+ offers the following advantages over RADIUS: 
TACACS+ uses TCP‐based connection‐oriented transport; whereas RADIUS is UDP‐based. TCP offers a connection‐oriented transport, while UDP offers best‐effort delivery. RADIUS requires additional programmable variables such as re‐transmit attempts and time‐outs to compensate for best‐effort transport, but it lacks the level of built‐in support that a TCP transport offers.

TACACS+ offers full packet encryption whereas RADIUS offers password‐only encryption in authentication requests.

TACACS+ separates authentication, authorization and accounting.
How TACACS+ Authentication Works
TACACS+ works much in the same way as RADIUS authentication as described on page 98.
1. Remote administrator connects to the switch and provides user name and password.
2. Using Authentication/Authorization protocol, the switch sends request to authentication server.
3. Authentication server checks the request against the user ID database.
4. Using TACACS+ protocol, the authentication server instructs the switch to grant or deny administrative access.
During a session, if additional authorization checking is needed, the switch checks with a TACACS+ server to determine if the user is granted permission to use a particular command. 102
G8052 Application Guide for ENOS 8.4
TACACS+ Authentication Features in Enterprise NOS
Authentication is the action of determining the identity of a user, and is generally done when the user first attempts to log in to a device or gain access to its services. ENOS supports ASCII inbound login to the device. PAP, CHAP and ARAP login methods, TACACS+ change password requests, and one‐time password authentication are not supported.
Authorization
Authorization is the action of determining a user’s privileges on the device, and usually takes place after authentication.
The default mapping between TACACS+ authorization levels and ENOS management access levels is shown in Table 8. The authorization levels must be defined on the TACACS+ server. Table 8. Default TACACS+ Authorization Levels
ENOS User Access Level
TACACS+ level
user
0
oper
3
admin
6
Alternate mapping between TACACS+ authorization levels and ENOS management access levels is shown in Table 9. Use the following command to set the alternate TACACS+ authorization levels. RS G8052(config)# tacacs­server privilege­mapping
Table 9. Alternate TACACS+ Authorization Levels
ENOS User Access Level
TACACS+ level
user
0 ‐ 1
oper
6 ‐ 8
admin
14 ‐ 15
If the remote user is successfully authenticated by the authentication server, the switch verifies the privileges of the remote user and authorizes the appropriate access. The administrator has an option to allow secure backdoor access via Telnet/SSH. Secure backdoor provides switch access when the TACACS+ servers cannot be reached. You always can access the switch via the console port, by using notacacs and the administrator password, whether secure backdoor is enabled or not. Note: To obtain the TACACS+ backdoor password for your G8052, contact Technical Support. © Copyright Lenovo 2016
Chapter 5: Authentication & Authorization Protocols
103
Accounting
Accounting is the action of recording a userʹs activities on the device for the purposes of billing and/or security. It follows the authentication and authorization actions. If the authentication and authorization is not performed via TACACS+, there are no TACACS+ accounting messages sent out.
You can use TACACS+ to record and track software login access, configuration changes, and interactive commands. The G8052 supports the following TACACS+ accounting attributes: 
protocol (console/Telnet/SSH/HTTP/HTTPS)

start_time

stop_time

elapsed_time

disc_cause
Note: When using the Browser‐Based Interface, the TACACS+ Accounting Stop records are sent only if the Logout button on the browser is clicked. Command Authorization and Logging
When TACACS+ Command Authorization is enabled, ENOS configuration commands are sent to the TACACS+ server for authorization. Use the following command to enable TACACS+ Command Authorization: RS G8052(config)# tacacs­server command­authorization
When TACACS+ Command Logging is enabled, ENOS configuration commands are logged on the TACACS+ server. Use the following command to enable TACACS+ Command Logging: RS G8052(config)# tacacs­server command­logging
The following examples illustrate the format of ENOS commands sent to the TACACS+ server: authorization request, cmd=shell, cmd­arg=interface ip
accounting request, cmd=shell, cmd­arg=interface ip
authorization request, cmd=shell, cmd­arg=enable
accounting request, cmd=shell, cmd­arg=enable
104
G8052 Application Guide for ENOS 8.4
Configuring TACACS+ Authentication on the Switch
1. Configure the IPv4 addresses of the Primary and Secondary TACACS+ servers, and enable TACACS authentication. RS G8052(config)# tacacs­server primary­host 10.10.1.1
RS G8052(config)# tacacs­server secondary­host 10.10.1.2
RS G8052(config)# tacacs­server enable
Note: You can use a configured loopback address as the source address so the TACACS+ server accepts requests only from the expected loopback address block. Use the following command to specify the loopback interface:
RS G8052(config)# ip tacacs source­interface loopback <1‐5>
2. Configure the TACACS+ secret and second secret. RS G8052(config)# tacacs­server primary­host 10.10.1.1 key <1‐32 character secret>
RS G8052(config)# tacacs­server secondary­host 10.10.1.2 key <1‐32 character secret>
3. If desired, you may change the default TCP port number used to listen to TACACS+. The well‐known port for TACACS+ is 49. RS G8052(config)# tacacs­server port <TCP port number>
4. Configure the number of retry attempts, and the timeout period. RS G8052(config)# tacacs­server retransmit 3
RS G8052(config)# tacacs­server timeout 5 © Copyright Lenovo 2016
Chapter 5: Authentication & Authorization Protocols
105
LDAP Authentication and Authorization
ENOS supports the LDAP (Lightweight Directory Access Protocol) method to authenticate and authorize remote administrators to manage the switch. LDAP is based on a client/server model. The switch acts as a client to the LDAP server. A remote user (the remote administrator) interacts only with the switch, not the back‐end server and database.
LDAP authentication consists of the following components:
A protocol with a frame format that utilizes TCP over IP
A centralized server that stores all the user authorization information
 A client: in this case, the switch


Each entry in the LDAP server is referenced by its Distinguished Name (DN). The DN consists of the user‐account name concatenated with the LDAP domain name. If the user‐account name is John, the following is an example DN:
uid=John,ou=people,dc=domain,dc=com
Configuring the LDAP Server
G8052 user groups and user accounts must reside within the same domain. On the LDAP server, configure the domain to include G8052 user groups and user accounts, as follows:

User Accounts:
Use the uid attribute to define each individual user account. If a custom attribute is used to define individual users, it must also be configured on the switch.

User Groups:
Use the members attribute in the groupOfNames object class to create the user groups. The first word of the common name for each user group must be equal to the user group names defined in the G8052, as follows:

admin

oper

user
Configuring LDAP Authentication on the Switch
1. Turn LDAP authentication on, then configure the IPv4 addresses of the Primary and Secondary LDAP servers. RS G8052(config)# ldap­server enable
RS G8052(config)# ldap­server primary­host 10.10.1.1
RS G8052(config)# ldap­server secondary­host 10.10.1.2
2. Configure the domain name.
RS G8052(config)# ldap­server domain <ou=people,dc=my‐domain,dc=com> 3. You may change the default TCP port number used to listen to LDAP (optional).
106
G8052 Application Guide for ENOS 8.4
The well‐known port for LDAP is 389.
RS G8052(config)# ldap­server port <1‐65000>
4. Configure the number of retry attempts for contacting the LDAP server, and the timeout period.
RS G8052(config)# ldap­server retransmit 3
RS G8052(config)# ldap­server timeout 10 5. You may change the default LDAP attribute (uid) or add a custom attribute. For instance, Microsoft’s Active Directory requires the cn attribute.
RS G8052(config)# ldap­server attribute username <128 alpha‐numeric characters>
© Copyright Lenovo 2016
Chapter 5: Authentication & Authorization Protocols
107
108
G8052 Application Guide for ENOS 8.4
Chapter 6. 802.1X Port-Based Network Access Control
Port‐Based Network Access control provides a means of authenticating and authorizing devices attached to a LAN port that has point‐to‐point connection characteristics. It prevents access to ports that fail authentication and authorization. This feature provides security to ports of the RackSwitch G8052 (G8052) that connect to blade servers.
The following topics are discussed in this section:
© Copyright Lenovo 2016

“Extensible Authentication Protocol over LAN” on page 110

“EAPoL Authentication Process” on page 111

“EAPoL Port States” on page 113

“Guest VLAN” on page 113

“Supported RADIUS Attributes” on page 114

“EAPoL Configuration Guidelines” on page 116
109
Extensible Authentication Protocol over LAN
Lenovo Enterprise Network Operating System can provide user‐level security for its ports using the IEEE 802.1X protocol, which is a more secure alternative to other methods of port‐based network access control. Any device attached to an 802.1X‐enabled port that fails authentication is prevented access to the network and denied services offered through that port.
The 802.1X standard describes port‐based network access control using Extensible Authentication Protocol over LAN (EAPoL). EAPoL provides a means of authenticating and authorizing devices attached to a LAN port that has point‐to‐point connection characteristics and of preventing access to that port in cases of authentication and authorization failures.
EAPoL is a client‐server protocol that has the following components:

Supplicant or Client The Supplicant is a device that requests network access and provides the required credentials (user name and password) to the Authenticator and the Authenticator Server.

Authenticator The Authenticator enforces authentication and controls access to the network. The Authenticator grants network access based on the information provided by the Supplicant and the response from the Authentication Server. The Authenticator acts as an intermediary between the Supplicant and the Authentication Server: requesting identity information from the client, forwarding that information to the Authentication Server for validation, relaying the server’s responses to the client, and authorizing network access based on the results of the authentication exchange. The G8052 acts as an Authenticator.

Authentication Server
The Authentication Server validates the credentials provided by the Supplicant to determine if the Authenticator ought to grant access to the network. The Authentication Server may be co‐located with the Authenticator. The G8052 relies on external RADIUS servers for authentication.
Upon a successful authentication of the client by the server, the 802.1X‐controlled port transitions from unauthorized to authorized state, and the client is allowed full access to services through the port. When the client sends an EAP‐Logoff message to the authenticator, the port will transition from authorized to unauthorized state.
110
G8052 Application Guide for ENOS 8.4
EAPoL Authentication Process
The clients and authenticators communicate using Extensible Authentication Protocol (EAP), which was originally designed to run over PPP, and for which the IEEE 802.1X Standard has defined an encapsulation method over Ethernet frames, called EAP over LAN (EAPOL). Figure 1 shows a typical message exchange initiated by the client.
Figure 1. Authenticating a Port Using EAPoL
RADIUS
Server
802.1x Client
EAPOL
Ethernet
Lenovo Switch
Authenticator
(RADIUS Client)
RADIUS-EAP
UDP/IP
Port Unauthorized
EAPOL-Start
EAP-Request (Credentials)
EAP-Response (Credentials)
Radius-Access-Request
Radius-Access-Challenge
EAP-Request (Credentials)
EAP-Response (Credentials)
Radius-Access-Request
Radius-Access-Accept
EAP-Success
Port Authorized
© Copyright Lenovo 2016
Chapter 6: 802.1X Port-Based Network Access Control
111
EAPoL Message Exchange
During authentication, EAPOL messages are exchanged between the client and the G8052 authenticator, while RADIUS‐EAP messages are exchanged between the G8052 authenticator and the RADIUS server.
Authentication is initiated by one of the following methods:

The G8052 authenticator sends an EAP‐Request/Identity packet to the client

The client sends an EAPOL‐Start frame to the G8052 authenticator, which responds with an EAP‐Request/Identity frame.
The client confirms its identity by sending an EAP‐Response/Identity frame to the G8052 authenticator, which forwards the frame encapsulated in a RADIUS packet to the server.
The RADIUS authentication server chooses an EAP‐supported authentication algorithm to verify the client’s identity, and sends an EAP‐Request packet to the client via the G8052 authenticator. The client then replies to the RADIUS server with an EAP‐Response containing its credentials.
Upon a successful authentication of the client by the server, the 802.1X‐controlled port transitions from unauthorized to authorized state, and the client is allowed full access to services through the controlled port. When the client later sends an EAPOL‐Logoff message to the G8052 authenticator, the port transitions from authorized to unauthorized state.
If a client that does not support 802.1X connects to an 802.1X‐controlled port, the G8052 authenticator requests the clientʹs identity when it detects a change in the operational state of the port. The client does not respond to the request, and the port remains in the unauthorized state.
Note: When an 802.1X‐enabled client connects to a port that is not 802.1X‐controlled, the client initiates the authentication process by sending an EAPOL‐Start frame. When no response is received, the client retransmits the request for a fixed number of times. If no response is received, the client assumes the port is in authorized state, and begins sending frames, even if the port is unauthorized.
112
G8052 Application Guide for ENOS 8.4
EAPoL Port States
The state of the port determines whether the client is granted access to the network, as follows:

Unauthorized
While in this state the port discards all ingress and egress traffic except EAP packets.

Authorized
When the client is successfully authenticated, the port transitions to the authorized state allowing all traffic to and from the client to flow normally.

Force Unauthorized
You can configure this state that denies all access to the port.

Force Authorized
You can configure this state that allows full access to the port.
Use the 802.1X global configuration commands (dot1x) to configure 802.1X authentication for all ports in the switch. Use the 802.1X port commands to configure a single port.
Guest VLAN
The guest VLAN provides limited access to unauthenticated ports. The guest VLAN can be configured using the following commands:
RS G8052(config)# dot1x guest­vlan ?
Client ports that have not received an EAPOL response are placed into the Guest VLAN, if one is configured on the switch. Once the port is authenticated, it is moved from the Guest VLAN to its configured VLAN. When Guest VLAN enabled, the following considerations apply while a port is in the unauthenticated state:
© Copyright Lenovo 2016

The port is placed in the guest VLAN.

The Port VLAN ID (PVID) is changed to the Guest VLAN ID.

Port tagging is disabled on the port.
Chapter 6: 802.1X Port-Based Network Access Control
113
Supported RADIUS Attributes
The 802.1X Authenticator relies on external RADIUS servers for authentication with EAP. Table 10 lists the RADIUS attributes that are supported as part of RADIUS‐EAP authentication based on the guidelines specified in Annex D of the 802.1X standard and RFC 3580.
Table 10. Support for RADIUS Attributes
114
# Attribute
Attribute Value
A-R
A-A
A-C
A-R
1 User‐Name
The value of the Type‐Data field from the supplicant’s EAP‐Response/ Identity message. If the Identity is unknown (for example, Type‐Data field is zero bytes in length), this attribute will have the same value as the Calling‐Station‐Id.
1
0‐1
0
0
4 NAS‐IP‐Address IPv4 address of the authenticator used for Radius communication.
1
0
0
0
5 NAS‐Port
Port number of the authenticator port to which the supplicant is attached.
1
0
0
0
24 State
Server‐specific value. This is sent unmodified back to the server in an Access‐Request that is in response to an Access‐Challenge.
0‐1
0‐1
0‐1
0
30 Called‐Station‐I
D
The MAC address of the authenticator encoded as an ASCII string in canonical format, such as 000D5622E3 9F.
1
0
0
0
31 Calling‐Station‐I
D
The MAC address of the supplicant encoded as an ASCII string in canonical format, such as 00034B436206.
1
0
0
0
64 Tunnel‐Type
Only VLAN (type 13) is currently supported (for 802.1X RADIUS VLAN assignment). The attribute must be untagged (the Tag field must be 0).
0
0‐1
0
0
65 Tunnel‐Medium‐ Only 802 (type 6) is currently Type
supported (for 802.1X RADIUS VLAN assignment). The attribute must be untagged (the Tag field must be 0).
0
0‐1
0
0
G8052 Application Guide for ENOS 8.4
Table 10. Support for RADIUS Attributes (continued)
# Attribute
Attribute Value
A-R
A-A
A-C
A-R
81 Tunnel‐Private‐
Group‐ID
VLAN ID (1‐4094). When 802.1X RADIUS VLAN assignment is enabled on a port, if the RADIUS server includes the tunnel attributes defined in RFC 2868 in the Access‐Accept packet, the switch will automatically place the authenticated port in the specified VLAN. Reserved VLANs (such as for management) may not be specified. The attribute must be untagged (the Tag field must be 0).
0
0‐1
0
0
79 EAP‐Message
Encapsulated EAP packets from the supplicant to the authentication server (Radius) and vice‐versa. The authenticator relays the decoded packet to both devices.
1+
1+
1+
1+
80 Message‐
Authenticator
Always present whenever an EAP‐Message attribute is also included. Used to integrity‐protect a packet. 1
1
1
1
87 NAS‐Port‐ID
Name assigned to the authenticator port, e.g. Server1_Port3
1
0
0
0
Legend: RADIUS Packet Types: A‐R (Access‐Request), A‐A (Access‐Accept), A‐C (Access‐Challenge), A‐R (Access‐Reject)
RADIUS Attribute Support:





© Copyright Lenovo 2016
0
0+
0‐1
1
1+
This attribute MUST NOT be present in a packet.
Zero or more instances of this attribute MAY be present in a packet.
Zero or one instance of this attribute MAY be present in a packet.
Exactly one instance of this attribute MUST be present in a packet.
One or more of these attributes MUST be present.
Chapter 6: 802.1X Port-Based Network Access Control
115
EAPoL Configuration Guidelines
When configuring EAPoL, consider the following guidelines:
116

The 802.1X port‐based authentication is currently supported only in point‐to‐point configurations, that is, with a single supplicant connected to an 802.1X‐enabled switch port.

When 802.1X is enabled, a port has to be in the authorized state before any other Layer 2 feature can be operationally enabled. For example, the STG state of a port is operationally disabled while the port is in the unauthorized state.

The 802.1X supplicant capability is not supported. Therefore, none of its ports can successfully connect to an 802.1X‐enabled port of another device, such as another switch, that acts as an authenticator, unless access control on the remote port is disabled or is configured in forced‐authorized mode. For example, if a G8052 is connected to another G8052, and if 802.1X is enabled on both switches, the two connected ports must be configured in force‐authorized mode.

Unsupported 802.1X attributes include Service‐Type, Session‐Timeout, and Termination‐Action.

RADIUS accounting service for 802.1X‐authenticated devices or users is not currently supported.

Configuration changes performed using SNMP and the standard 802.1X MIB will take effect immediately.
G8052 Application Guide for ENOS 8.4
Chapter 7. Access Control Lists
Access Control Lists (ACLs) are filters that permit or deny traffic for security purposes. They can also be used with QoS to classify and segment traffic to provide different levels of service to different traffic types. Each filter defines the conditions that must match for inclusion in the filter, and also the actions that are performed when a match is made.
Lenovo Enterprise Network Operating System 8.4 supports the following ACLs:

IPv4 ACLs
Up to 640 ACLs are supported for networks that use IPv4 addressing. IPv4 ACLs are configured using the following ISCLI command path:
RS G8052(config)# access­control list <IPv4 ACL number> ?

IPv6 ACLs
Up to 128 ACLs are supported for networks that use IPv6 addressing. IPv6 ACLs are configured using the following ISCLI command path:
RS G8052(config)# access­control list6 <IPv6 ACL number> ?
Note: ACLs are not supported with IPv6 in Stacking mode.

VLAN Maps (VMaps)
Up to 128 VLAN Maps are supported for attaching filters to VLANs rather than ports. See “VLAN Maps” on page 129 for details.

Management ACLs (MACLs)
Up to 128 MACLs are supported for filtering traffic toward CPU. MACLs are configured using the following ISCLI command path: RS G8052(config)# access­control macl <MACL number> ?
© Copyright Lenovo 2016
117
Summary of Packet Classifiers
ACLs allow you to classify packets according to a variety of content in the packet header (such as the source address, destination address, source port number, destination port number, and others). Once classified, packet flows can be identified for more processing.
IPv4 ACLs, IPv6 ACLs, and VMaps allow you to classify packets based on the following packet attributes:


Ethernet header options (for IPv4 ACLs and VMaps only)

Source MAC address

Destination MAC address

VLAN number and mask

Ethernet type (ARP, IP, IPv6, MPLS, RARP, etc.)

Ethernet Priority (the IEEE 802.1p Priority)
IPv4 header options (for IPv4 ACLs and VMaps only)

Source IPv4 address and subnet mask

Destination IPv4 address and subnet mask

Type of Service value

IP protocol number or name as shown in Table 11:
Table 11. Well‐Known Protocol Types

118
Number
Protocol Name
1
2
6
17
89
112
icmp
igmp
tcp
udp
ospf
vrrp
IPv6 header options (for IPv6 ACLs only)

Source IPv6 address and prefix length

Destination IPv6 address and prefix length

Next Header value

Flow Label value

Traffic Class value
G8052 Application Guide for ENOS 8.4

TCP/UDP header options (for all ACLs)

TCP/UDP application source port and mask as shown in Table 12

TCP/UDP application destination port as shown in Table 12
Table 12. Well‐Known Application Ports
TCP/UDP
Port Application
20
21
22
23
25
37
42
43
53
69
70

ftp‐data
ftp
ssh
telnet
smtp
time
name
whois
domain
tftp
gopher
TCP/UDP
Port Application
79
80
109
110
111
119
123
143
144
161
162
finger
http
pop2
pop3
sunrpc
nntp
ntp
imap
news
snmp
snmptrap
TCP/UDP
Port Application
179
194
220
389
443
520
554
1645/1812
1813
1985
bgp
irc
imap3
ldap
https
rip
rtsp
Radius
Radius Accounting
hsrp
TCP/UDP flag value as shown in Table 13
Table 13. Well Known TCP Flag Values


Flag
Value
URG
ACK
PSH
RST
SYN
FIN
0x0020
0x0010
0x0008
0x0004
0x0002
0x0001
Packet format (for IPv4 ACLs and VMaps only)

Ethernet format (eth2, SNAP, LLC)

Ethernet tagging format

IP format (IPv4, IPv6)
Egress port packets (for all ACLs)
Summary of ACL Actions
Once classified using ACLs, the identified packet flows can be processed differently. For each ACL, an action can be assigned. The action determines how the switch treats packets that match the classifiers assigned to the ACL. G8052 ACL actions include the following:





© Copyright Lenovo 2016
Pass or Drop the packet
Redirect the packet
Re‐mark the packet with a new DiffServ Code Point (DSCP)
Re‐mark the 802.1p field
Set the COS queue
Chapter 7: Access Control Lists
119
Assigning Individual ACLs to a Port
Once you configure an ACL, you must assign the ACL to the appropriate ports. Each port can accept multiple ACLs, and each ACL can be applied for multiple ports. ACLs can be assigned individually, or in groups.
To assign an individual ACLs to a port, use the following IP Interface Mode commands: RS G8052(config)# interface port <port>
RS G8052(config­if)# access­control list <IPv4 ACL number>
RS G8052(config­if)# access­control list6 <IPv6 ACL number>
When multiple ACLs are assigned to a port, higher‐priority ACLs are considered first, and their action takes precedence over lower‐priority ACLs. ACL order of precedence is discussed in the next section.
To create and assign ACLs in groups, see “ACL Groups” on page 121.
ACL Order of Precedence
When multiple ACLs are assigned to a port, they are evaluated in numeric sequence, based on the ACL number. Lower‐numbered ACLs take precedence over higher‐numbered ACLs. For example, ACL 1 (if assigned to the port) is evaluated first and has top priority.
If multiple ACLs match the port traffic, only the action of the one with the lowest ACL number is applied. The others are ignored.
If no assigned ACL matches the port traffic, no ACL action is applied.
120
G8052 Application Guide for ENOS 8.4
ACL Groups
To assist in organizing multiple ACLs and assigning them to ports, you can place ACLs into ACL Groups, thereby defining complex traffic profiles. ACLs and ACL Groups can then be assigned on a per‐port basis. An ACL can only be assigned to one ACL group. Any ACL or ACL Group can be assigned to multiple ports. If a specific ACL is assigned to a port multiple times, only one instance is used. The redundant entries are ignored.

Individual ACLs
The G8052 supports up to 640 ACLs. Each ACL defines one filter rule for matching traffic criteria. Each filter rule can also include an action (permit or deny the packet). For example:
ACL 1:
VLAN = 1
SIP = 10.10.10.1 (255.255.255.0)
Action = permit

Access Control List Groups
An Access Control List Group (ACL Group) is a collection of ACLs. For example:
ACL Group 1
ACL 1:
VLAN = 1
SIP = 10.10.10.1 (255.255.255.0)
Action = permit
ACL 2:
VLAN = 2
SIP = 10.10.10.2 (255.255.255.0)
Action = deny
ACL 3:
Priority = 7
DIP = 10.10.10.3 (255.255.255.0)
Action = permit
ACL Groups organize ACLs into traffic profiles that can be more easily assigned to ports. The G8052 supports up to 640 ACL Groups.
Note: ACL Groups are used for convenience in assigning multiple ACLs to ports. ACL Groups have no effect on the order in which ACLs are applied (see “ACL Order of Precedence” on page 120). All ACLs assigned to the port (whether individually assigned or part of an ACL Group) are considered as individual ACLs for the purposes of determining their order of precedence.
© Copyright Lenovo 2016
Chapter 7: Access Control Lists
121
Assigning ACL Groups to a Port
To assign an ACL Group to a port, use the following command: RS G8052(config­if)# access­control group <ACL group number>
RS G8052(config­if)# exit
ACL Metering and Re-Marking
You can define a profile for the aggregate traffic flowing through the G8052 by configuring a QoS meter (if desired) and assigning ACLs to ports.
Note: When you add ACLs to a port, make sure they are ordered correctly in terms of precedence (see “ACL Order of Precedence” on page 120).
Actions taken by an ACL are called In‐Profile actions. You can configure additional In‐Profile and Out‐of‐Profile actions on a port. Data traffic can be metered, and re‐marked to ensure that the traffic flow provides certain levels of service in terms of bandwidth for different types of network traffic.
Metering
QoS metering provides different levels of service to data streams through user‐configurable parameters. A meter is used to measure the traffic stream against a traffic profile which you create. Thus, creating meters yields In‐Profile and Out‐of‐Profile traffic for each ACL, as follows:

In‐Profile—If there is no meter configured or if the packet conforms to the meter, the packet is classified as In‐Profile.

Out‐of‐Profile—If a meter is configured and the packet does not conform to the meter (exceeds the committed rate or maximum burst rate of the meter), the packet is classified as Out‐of‐Profile.
Using meters, you set a Committed Rate in Kbps (1000 bits per second in each Kbps). All traffic within this Committed Rate is in‐profile. Additionally, you can set a Maximum Burst Size that specifies an allowed data burst larger than the Committed Rate for a brief period. These parameters define the In‐Profile traffic.
Meters keep the sorted packets within certain parameters. You can configure a meter on an ACL, and perform actions on metered traffic, such as packet re‐marking.
Re-Marking
Re‐marking allows for the treatment of packets to be reset based on new network specifications or desired levels of service. You can configure the ACL to re‐mark a packet as follows:
122

Change the DSCP value of a packet, used to specify the service level that traffic receives.

Change the 802.1p priority of a packet.
G8052 Application Guide for ENOS 8.4
ACL Port Mirroring
For IPv4 ACLs and VMaps, packets that match the filter can be mirrored to another switch port for network diagnosis and monitoring.
The source port for the mirrored packets cannot be a portchannel, but may be a member of a portchannel.
The destination port to which packets are mirrored must be a physical port.
The action (permit, drop, etc.) of the ACL or VMap must be configured before assigning it to a port.
Use the following commands to add mirroring to an ACL:

For IPv4 ACLs: RS G8052(config)# access­control list <ACL number> mirror port <destination port>
The ACL must be also assigned to it target ports as usual (see “Assigning Individual ACLs to a Port” on page 120).

For VMaps (see “VLAN Maps” on page 129): RS G8052(config)# access­control vmap <VMap number> mirror port <monitor destination port>
See the configuration example on page 130.
Viewing ACL Statistics
ACL statistics display how many packets have “hit” (matched) each ACL. Use ACL statistics to check filter performance or to debug the ACL filter configuration.
You must enable statistics for each ACL that you wish to monitor: RS G8052(config)# access­control list <ACL number> statistics
© Copyright Lenovo 2016
Chapter 7: Access Control Lists
123
ACL Logging
ACLs are generally used to enhance port security. Traffic that matches the characteristics (source addresses, destination addresses, packet type, etc.) specified by the ACLs on specific ports is subject to the actions (chiefly permit or deny) defined by those ACLs. Although switch statistics show the number of times particular ACLs are matched, the ACL logging feature can provide additional insight into actual traffic patterns on the switch, providing packet details in the system log for network debugging or security purposes.
Enabling ACL Logging
By default, ACL logging is disabled. Enable or disable ACL logging on a per‐ACL basis as follows:
RS G8052(config)# [no] access­control list <IPv4 ACL number> log
RS G8052(config)# [no] access­control list6 <IPv6 ACL number> log
Logged Information
When ACL logging is enabled on any particular ACL, the switch will collect information about packets that match the ACL. The information collected depends on the ACL type:

For IP‐based ACLs, information is collected regarding

Source IP address

Destination IP address

TCP/UDP port number

ACL action

Number of packets logged
For example:
Sep 27 4:20:28 DUT3 NOTICE ACL­LOG: %IP ACCESS LOG: list ACL­IP­12­IN denied tcp 1.1.1.1 (0) ­> 200.0.1.2 (0), 150 packets.

For MAC‐based ACLs, information is collected regarding

Source MAC address

Source IP address

Destination IP address

TCP/UDP port number

ACL action

Number of packets logged
For example:
Sep 27 4:25:38 DUT3 NOTICE ACL­LOG: %MAC ACCESS LOG: list ACL­MAC­12­IN permitted tcp 1.1.1.2 (0) (12, 00:ff:d7:66:74:62) ­> 200.0.1.2 (0) (00:18:73:ee:a7:c6), 32 packets.
124
G8052 Application Guide for ENOS 8.4
Rate Limiting Behavior
Because ACL logging can be CPU‐intensive, logging is rate‐limited. By default, the switch will log only 10 matching packets per second. This pool is shared by all log‐enabled ACLs. The global rate limit can be changed as follows:
RS G8052(config)# access­control log rate­limit <1‐1000>
Where the limit is specified in packets per second.
Log Interval
For each log‐enabled ACL, the first packet that matches the ACL initiates an immediate message in the system log. Beyond that, additional matches are subject to the log interval. By default, the switch will buffer ACL log messages for a period of 300 seconds. At the end of that interval, all messages in the buffer are written to the system log. The global interval value can be changed as follows:
RS G8052(config)# access­control log interval <5‐600>
Where the interval rate is specified in seconds.
In any given interval, packets that have identical log information are condensed into a single message. However, the packet count shown in the ACL log message represents only the logged messages, which due to rate‐limiting, may be significantly less than the number of packets actually matched by the ACL.
Also, the switch is limited to 64 different ACL log messages in any interval. Once the threshold is reached, the oldest message will be discarded in favor of the new message, and an overflow message will be added to the system log.
ACL Logging Limitations
ACL logging reserves packet queue 1 for internal use. Features that allow remapping packet queues (such as CoPP) may not behave as expected if other packet flows are reconfigured to use queue 1.
© Copyright Lenovo 2016
Chapter 7: Access Control Lists
125
ACL Configuration Examples
This section contains examples of access control list configuration.
ACL Example 1
Use this configuration to block traffic to a specific host. All traffic that ingresses on port 1 is denied if it is destined for the host at IP address 100.10.1.1
1. Configure an Access Control List. RS G8052(config)# access­control list 1 ipv4 destination­ip­address 100.10.1.1
RS G8052(config)# access­control list 1 action deny
2. Add ACL 1 to port 1. RS G8052(config)# interface port 1
RS G8052(config­if)# access­control list 1
RS G8052(config­if)# exit
ACL Example 2
Use this configuration to block traffic from a network destined for a specific host address. All traffic that ingresses in port 2 with source IP from class 100.10.1.0/24 and destination IP 200.20.2.2 is denied.
1. Configure an Access Control List. RS G8052(config)# access­control list 2 ipv4 source­ip­address 100.10.1.0 255.255.255.0
RS G8052(config)# access­control list 2 ipv4 destination­ip­address 200.20.2.2 255.255.255.255
RS G8052(config)# access­control list 2 action deny
2. Add ACL 2 to port 2. RS G8052(config)# interface port 2
RS G8052(config­if)# access­control list 2
RS G8052(config­if)# exit
126
G8052 Application Guide for ENOS 8.4
ACL Example 3
Use this configuration to block traffic from a specific IPv6 source address. All traffic that ingresses in port 2 with source IP from class 2001:0:0:5:0:0:0:2/128 is denied.
1. Configure an Access Control List. RS G8052(config)# access­control list6 3 ipv6 source­address 2001:0:0:5:0:0:0:2 128
RS G8052(config)# access­control list6 3 action deny
2. Add ACL 2 to port 2. RS G8052(config)# interface port 2
RS G8052(config­if)# access­control list6 3
RS G8052(config­if)# exit
ACL Example 4
Use this configuration to deny all ARP packets that ingress a port.
1. Configure an Access Control List. RS G8052(config)# access­control list 2 ethernet ethernet­type arp
RS G8052(config)# access­control list 2 action deny
2. Add ACL 2 to port EXT2. RS G8052(config)# interface port 2
RS G8052(config­if)# access­control list 2
RS G8052(config­if)# exit
ACL Example 5
Use the following configuration to permit access to hosts with destination MAC address that matches 11:05:00:10:00:00 FF:F5:FF:FF:FF:FF and deny access to all other hosts.
1. Configure Access Control Lists. RS G8052(config)# access­control list 30 ethernet destination­mac­address 11:05:00:10:00:00 FF:F5:FF:FF:FF:FF
RS G8052(config)# access­control list 30 action permit
RS G8052(config)# access­control list 100 ethernet destination­mac­address 00:00:00:00:00:00 00:00:00:00:00:00
RS G8052(config)# access­control list 100 action deny
2. Add ACLs to a port. RS
RS
RS
RS
© Copyright Lenovo 2016
G8052(config)# interface port 2
G8052(config­if)# access­control list 30
G8052(config­if)# access­control list 100
G8052(config­if)# exit
Chapter 7: Access Control Lists
127
ACL Example 6
This configuration blocks traffic from a network that is destined for a specific egress port. All traffic that ingresses port 1 from the network 100.10.1.0/24 and is destined for port 3 is denied.
1. Configure an Access Control List. RS G8052(config)# access­control list 4 ipv4 source­ip­address 100.10.1.0 255.255.255.0
RS G8052(config)# access­control list 4 egress­port 3
RS G8052(config)# access­control list 4 action deny
2. Add ACL 4 to port 1. RS G8052(config)# interface port 1
RS G8052(config­if)# access­control list 4
RS G8052(config­if)# exit
128
G8052 Application Guide for ENOS 8.4
VLAN Maps
A VLAN map (VMap) is an ACL that can be assigned to a VLAN or VM group rather than to a switch port as with IPv4 ACLs. This is particularly useful in a virtualized environment where traffic filtering and metering policies must follow virtual machines (VMs) as they migrate between hypervisors.
The G8052 supports up to 128 VMaps.
Individual VMap filters are configured in the same fashion as IPv4 ACLs, except that VLANs cannot be specified as a filtering criteria (unnecessary, since the VMap are assigned to a specific VLAN or associated with a VM group VLAN).
VMaps are configured using the following ISCLI configuration command path:
RS G8052(config)# access­control vmap <VMap ID> ?
action Set filter action
egress­port Set to filter for packets egressing this port
ethernet Ethernet header options
ipv4 IP version 4 header options
meter ACL metering configuration
mirror Mirror options
packet­format Set to filter specific packet format types
re­mark ACL re­mark configuration
statistics Enable access control list statistics
tcp­udp TCP and UDP filtering options
Once a VMap filter is created, it can be assigned or removed using the following configuration commands:

For regular VLAN, use config‐vlan mode:
RS G8052(config)# vlan <VLAN ID>
RS G8052(config­vlan)# [no] vmap <VMap ID> [serverports| non­serverports]

For a VM group (see “VM Group Types” on page 300), use the global configuration mode:
RS G8052(config)# [no] virt vmgroup <ID> vmap <VMap ID> [serverports|non­serverports]
Note: Each VMap can be assigned to only one VLAN or VM group. However, each VLAN or VM group may have multiple VMaps assigned to it.
When the optional serverports or non­serverports parameter is specified, the action to add or remove the VMap is applied for either the switch server ports (serverports) or uplink ports (non­serverports). If omitted, the operation will be applied to all ports in the associated VLAN or VM group.
© Copyright Lenovo 2016
Chapter 7: Access Control Lists
129
VMap Example
In this example, EtherType 2 traffic from VLAN 3 server ports is mirrored to a network monitor on port 4.
RS G8052(config)# access­control vmap 21 packet­format ethernet ethernet­type2
RS G8052(config)# access­control vmap 21 mirror port 4
RS G8052(config)# access­control vmap 21 action permit
RS G8052(config)# vlan 3
RS G8052(config­vlan)# vmap 21 serverports
130
G8052 Application Guide for ENOS 8.4
Management ACLs
Management ACLs (MACLs) filter inbound traffic i.e. traffic toward the CPU. MACLs are applied switch‐wide. Traffic can be filtered based on the following:

IPv4 source address

IPv4 destination address

IPv4 protocols 
TCP/UDP destination or source port
Lower MACL numbers have higher priority.
Following is an example MACL configuration based on a destination IP address and a TCP‐UDP destination port: RS G8052(config)# access­control macl 1 ipv4 destination­ip­address 1.1.1.1 255.255.255.0
RS G8052(config)# access­control macl 1 tcp­udp destination­port 111 0xffff
RS G8052(config)# access­control macl 1 statistics
RS G8052(config)# access­control macl 1 action permit
RS G8052(config)# access­control macl 1 enable
Use the following command to view the MACL configuration: RS G8052(config)# show access­control macl 1
MACL 1 profile : Enabled
IPv4
- DST IP
: 1.1.1.1/255.255.255.0
TCP/UDP
- DST Port
: 111/0xffff
Action
: Permit
Statistics
: Enabled
© Copyright Lenovo 2016
Chapter 7: Access Control Lists
131
Using Storm Control Filters
Excessive transmission of broadcast or multicast traffic can result in a network storm. A network storm can overwhelm your network with constant broadcast or multicast traffic, and degrade network performance. Common symptoms of a network storm are denial‐of‐service (DoS) attacks, slow network response times, and network operations timing out. The G8052 provides filters that can limit the number of the following packet types transmitted by switch ports: Broadcast packets
Multicast packets
 Unknown unicast packets (destination lookup failure)


Unicast packets whose destination MAC address is not in the Forwarding Database are unknown unicasts. When an unknown unicast is encountered, the switch handles it like a broadcast packet and floods it to all other ports in the VLAN (broadcast domain). A high rate of unknown unicast traffic can have the same negative effects as a broadcast storm. Configure broadcast filters on each port that requires broadcast storm control. Set a threshold that defines the total number of broadcast packets transmitted (0‐2097151), in packets per second. When the threshold is reached, no more packets of the specified type are transmitted.
To filter broadcast packets on a port, use the following commands: RS G8052(config)# interface port 1
RS G8052(config­if)# storm­control broadcast level rate <packets per second>
To filter multicast packets on a port, use the following commands: RS G8052(config­if)# storm­control multicast level rate <packets per second>
To filter unknown unicast packets on a port, use the following commands: RS G8052(config­if)# storm­control unicast level rate <packets per second>
RS G8052(config­if)# exit
132
G8052 Application Guide for ENOS 8.4
Chapter 8. Secure Input/Output Module
The Secure Input/Output Module (SIOM) enables you to determine which protocols can be enabled. The SIOM only allows secured traffic and secured authentication management.
The following topics are discussed in this chapter:
© Copyright Lenovo 2016

“SIOM Overview” on page 134

“Setting an SIOM Security Policy” on page 135

“Implementing Secure LDAP (LDAPS)” on page 138

“Using Cryptographic Mode” on page 141
133
SIOM Overview
A security policy is a set of rules to be enforced on the switch software. The SIOM contains the following sub‐features:

A Security Policy that can be enforced on the switch software

A Secure LDAP (LDAPS) implementation in addition to the current the LDAP feature
Note: SIOM is supported in stacking mode.
134
G8052 Application Guide for ENOS 8.4
Setting an SIOM Security Policy
The SIOM feature introduces the following levels of security policy:

Legacy Mode
Legacy Mode maintains the existing security behavior of the IOM or switch. All communication protocols currently supported by the IOM software continue to be allowed and supported in this mode. All behaviors of the IOM remain the same; the only difference is you can set the mode which will take effect after the next reboot of the switch.

Secure Mode
In Security Mode or SIOM, only secure communication protocols are allowed to be enabled. Communication protocols that are deemed to be not secure are disabled and not allowed to run on the switch.
Note: Once a switch has entered Secure Mode, it cannot return to Legacy Mode without a reboot. Enabling and Disabling the SIOM
To enable Secure Mode on the G8052, enter:
RS G8052(config)# boot security­policy secure­mode
Note: The switch will remain in Legacy Mode until you reboot. To disable Secure Mode on the G8052, enter:
RS G8052(config)# boot security­policy legacy­mode
Note: The switch will remain in Secure Mode until you reboot. To display the running security policy, enter:
RS G8052(config)# show boot security­policy
Note: In stacking mode, the Master and the Backup switches control the security policy.
Using Protocols With SIOM
Some protocols can be used with SIOM. This section explains which protocols can and cannot operate with SIOM on the RackSwitch G8052.
Insecure Protocols
When you are in Secure Mode, the following protocols are deemed “insecure” and are disabled:
© Copyright Lenovo 2016

HTTP 
LDAP Client

SNMPv1
Chapter 8: Secure Input/Output Module
135

SNMPv2

Telnet (server and client)

FTP (server and client)

Radius (client

TACACS+ (client)

TFTP Server
Except for the TFTP server, these protocols cannot be enabled when the switch is operating in Secure Mode because the commands to enable or disable them disappear with SIOM enabled.
The following protocols, although deemed “insecure” by SIOM, are enabled by default and can be disabled.

DHCP client 
SysLog
Note: Service Location Protocol (SLP) Discovery is also deemed “insecure” but is unaffected by Secure Mode. SLP has the same default settings as in Legacy Mode. If you can enable or disable SLP in Legacy Mode, you can enable or disable it the same way in Secure Mode.
The following supported protocols are not enabled by default but can always be enabled in Secure Mode.

DNS Resolution

TFTP client (for signed items only, such as switch images)
The following protocols, although deemed “insecure” and allowed by SIOM, are not supported by the G8052:

RCP

SMTP

MIME

TCP command in secure mode (Port 6090)

DHCPv6 client
Secure Protocols
The following protocols are deemed “secure” and are enabled by default in Secure Mode:

SCP Server

SNMPv3 Client

SFTP Client

SSHv2 Server

SSHv2 Client

HTTPS Server
You can disable these protocols.
136
G8052 Application Guide for ENOS 8.4
The following protocols are deemed “secure” and cannot be disabled in any mode:

NTP Client v4

LDAPS Client
The following protocols are also deemed “secure” on the G8052 and can be enabled. 
IKE

IPSec
The default state for these protocols in Secure Mode, whether enabled or disabled, is the same as in Legacy Mode.
The following protocols are deemed “secure” but are not currently supported by the G8052:

EAPoL

SCP

S/MIME

SNMPv3 Manager

TCP command secure mode (Port 6091)
Insecure Protocols Unaffected by SIOM
The following protocols are deemed “insecure” but can be enabled in all Security Policy Modes:

Ping

Ping IPv6

Traceroute

Traceroute IPv6

TFTP IPv6

SNMPv3 IPv6

bootp
Notes:
© Copyright Lenovo 2016

Telnet IPv6 and TFTP IPv6 are disabled in Secure Mode.

TFTP IPv6 is allowed in Secure Mode for signed image transfers only.
Chapter 8: Secure Input/Output Module
137
Implementing Secure LDAP (LDAPS)
Lightweight Directory Access Protocol (LDAP) is a protocol for accessing distributed directory information services over a network. Enterprise NOS uses LDAP for authentication and authorization. With an LDAP client enabled, the switch will authenticate a user and determine the user’s privilege level by checking with one or more directory servers instead of a local database of users. This prevents customers from having to configure local user accounts on multiple switches; they can maintain a centralized directory instead. As part of the SIOM, you can implement Secure Lightweight Directory Access Protocol (LDAPS) in addition to standard LDAP.
Enabling LDAPS
LDAPS is disabled by default. To enable LDAPS:
1. Turn LDAP authentication on RS G8052(config)# ldap­server enable
2. Enable LDAP Enhanced Mode:
RS G8052(config)# ldap­server mode enhanced
This changes the ldap­server subcommands to support LDAPS.
3. Configure the IPv4 addresses of each LDAP server. RS G8052(config)# ldap­server host {1­4} <IP address or hostname>
4. You may change the default TCP port number used to listen to LDAPS (optional).
The well‐known port for LDAP is 636.
RS G8052(config)# ldap­server port <1‐65000>
5. Configure the Security Mode:
RS G8052(config)# ldap­server security {clear|ldaps|mutual|starttls}
where:
138
Parameter
Description
clear
Cleartext Mode (no security)
ldaps
LDAPS Mode
mutual
Mutual authentication in Transport Layer Security (TLS)
starttls
Secure LDAP via StartTLS without cleartext fallback
G8052 Application Guide for ENOS 8.4
6. Configure the distinguished name (DN) and password (optional).
RS G8052(config)# ldap­server binddn dn “<distinguished name> “
RS G8052(config)# ldap­server binddn key “<password> “
If this is not configured, the switch will use user‐provided login credentials to bind. A DN will then be constructed from the userʹs login credentials and then used in the initial BIND attempt.
7. Configure the root DN:
RS G8052(config)# ldap­server basedn <root DN name>
8. Configure the user search attribute (optional):
RS G8052(config)# ldap­server attribute username <search attribute>
If no user search attribute is specified, the default is uid.
9. Configure the group search attribute (optional):
RS G8052(config)# ldap­server attribute group <search attribute>
If no group search attribute is specified, the default is memberOf.
10. Configure the login permissions attribute:
RS G8052(config)# ldap­server attribute login­permission <attribute>
Note: If no login permissions attribute is configured, LDAP client will not function.
11. Configure the group filter attribute (optional):
RS G8052(config)# ldap­server group­filter <filter attributes separated by comma>
Note: The group filter string must contain no whitespace.
If no group filter attribute is configured, no groups will be filtered and all groups will be considered in any search.
12. Enable DNS server verification:
RS G8052(config)# ldap­server srv
Disabling LDAPS
To disable LDAPS, enter:
RS G8052(config)# ldap­server security clear
RS G8052(config)# ldap­server mode legacy
For information about using LDAP in Legacy Mode, see “LDAP Authentication and Authorization” on page 106.
© Copyright Lenovo 2016
Chapter 8: Secure Input/Output Module
139
Syslogs and LDAPS
Syslogs are required for the following error conditions:
140

Password change required on first login

Password expired

Username or password invalid

Account temporarily locked

Unknown/no reason given
G8052 Application Guide for ENOS 8.4
Using Cryptographic Mode
The RackSwitch G8052 is able to change between Cryptographic Compatibility Mode and NIST SP 800‐131a Cryptographic Mode. In Cryptographic Mode, encryption key lengths must comply with NIST SP 800‐131a minimum requirements; only compliant encryption algorithms are allowed.
To enable Cryptographic Mode:
Note: You may want to save your configuration before enabling Cryptographic Mode, as this process will wipe out your configuration.
1. Set the boot mode:
RS G8052(config)# boot strict enable
2. Reboot the switch.
3. Verify that the switch is operating in Cryptographic Mode:
RS G8052# show boot strict
Current strict settings:
Strict Mode : enabled
Old default Snmpv3 accounts support : no
Strict settings saved:
Strict Mode : enabled
Old default Snmpv3 accounts support : no
© Copyright Lenovo 2016
Chapter 8: Secure Input/Output Module
141
142
G8052 Application Guide for ENOS 8.4
Part 3: Switch Basics
This section discusses basic switching functions:
 VLANs
 Port Aggregation
 Spanning Tree Protocols (Spanning Tree Groups, Rapid Spanning Tree Protocol, and Multiple Spanning Tree Protocol)
 Virtual Link Aggregation Groups
 Quality of Service
© Copyright Lenovo 2016
143
144
G8052 Application Guide for ENOS 8.4
Chapter 9. VLANs
This chapter describes network design and topology considerations for using Virtual Local Area Networks (VLANs). VLANs commonly are used to split up groups of network users into manageable broadcast domains, to create logical segmentation of workgroups, and to enforce security policies among logical segments. The following topics are discussed in this chapter: 
“VLANs and Port VLAN ID Numbers” on page 146

“VLAN Tagging/Trunk Mode” on page 148

“VLAN Topologies and Design Considerations” on page 153
This section discusses how you can connect users and segments to a host that supports many logical segments or subnets by using the flexibility of the multiple VLAN system.

“Protocol‐Based VLANs” on page 157

“Private VLANs” on page 160
Note: VLANs can be configured from the Command Line Interface (see “VLAN Configuration” as well as “Port Configuration” in the Command Reference). © Copyright Lenovo 2016
145
VLANs Overview
Setting up virtual LANs (VLANs) is a way to segment networks to increase network flexibility without changing the physical network topology. With network segmentation, each switch port connects to a segment that is a single broadcast domain. When a switch port is configured to be a member of a VLAN, it is added to a group of ports (workgroup) that belong to one broadcast domain.
Ports are grouped into broadcast domains by assigning them to the same VLAN. Frames received in one VLAN can only be forwarded within that VLAN, and multicast, broadcast, and unknown unicast frames are flooded only to ports in the same VLAN.
The RackSwitch G8052 (G8052) supports jumbo frames with a Maximum Transmission Unit (MTU) of 9,216 bytes. Within each frame, 18 bytes are reserved for the Ethernet header and CRC trailer. The remaining space in the frame (up to 9,198 bytes) comprise the packet, which includes the payload of up to 9,000 bytes and any additional overhead, such as 802.1q or VLAN tags. Jumbo frame support is automatic: it is enabled by default, requires no manual configuration, and cannot be manually disabled. VLANs and Port VLAN ID Numbers
VLAN Numbers
The G8052 supports up to 2048 VLANs per switch. Even though the maximum number of VLANs supported at any given time is 2048, each can be identified with any number between 1 and 4094. VLAN 1 is the default VLAN for the data ports.
Use the following command to view VLAN information: RS G8052)# show vlan
VLAN Name Status Ports
­­­­ ­­­­­­­­­­­­­­­­­­­­­­­­ ­­­­­­ ­­­­­­­­­­­­­­­­­­­­­­­­­
1 Default VLAN ena 1­48, XGE1­XGE4
2 VLAN 2 dis empty
146
G8052 Application Guide for ENOS 8.4
PVID/Native VLAN Numbers
Each port in the switch has a configurable default VLAN number, known as its PVID. By default, the PVID for all non‐management ports is set to 1, which correlates to the default VLAN ID. The PVID for each port can be configured to any VLAN number between 1 and 4094. Use the following command to view PVIDs: RS G8052# show interface information (or)
RS G8052# show interface trunk Alias Port Tag RMON Lrn Fld Openflow PVID DESCRIPTION VLAN(s)
Trk NVLAN ­­­­­­­­ ­­­­ ­­­ ­­­­ ­­­ ­­­ ­­­­­­­­ ­­­­­­ ­­­­­­­­­­­­­­ ­­­­­­­­­­­­­­­­­­­­­­
1 1 n d e e d 1 1
2 2 n d e e d 1 1
3 3 n d e e d 1 1
4 4 n d e e d 1 1
5 5 n d e e d 1 1
6 6 n d e e d 1 1
...
XGE1 49 n d e e d 23 23
XGE2 50 y d e e d 78 78 200
XGE3 51 n d e e d 23 23
XGE4 52 n d e e d 23 23
* = PVID/Native­VLAN is tagged. # = PVID is ingress tagged.
Trk = Trunk mode
NVLAN = Native­VLAN
Use the following command to set the port PVID/Native VLAN: Access Mode Port
RS G8052(config)# interface port <port number>
RS G8052(config­if)# switchport access vlan <VLAN ID>
For Trunk Mode Port
RS G8052(config)# interface port <port number>
RS G8052(config­if)# switchport trunk native vlan <VLAN ID>
Each port on the switch can belong to one or more VLANs, and each VLAN can have any number of switch ports in its membership. Any port that belongs to multiple VLANs, however, must have VLAN tagging/trunk mode enabled (see “VLAN Tagging/Trunk Mode” on page 148). © Copyright Lenovo 2016
Chapter 9: VLANs
147
VLAN Tagging/Trunk Mode
Lenovo Enterprise Network Operating System software supports 802.1Q VLAN tagging, providing standards‐based VLAN support for Ethernet systems.
Tagging places the VLAN identifier in the frame header of a packet, allowing each port to belong to multiple VLANs. When you add a port to multiple VLANs, you also must enable tagging on that port. Since tagging fundamentally changes the format of frames transmitted on a tagged port, you must carefully plan network designs to prevent tagged frames from being transmitted to devices that do not support 802.1Q VLAN tags, or devices where tagging is not enabled. Important terms used with the 802.1Q tagging feature are:

VLAN identifier (VID)—the 12‐bit portion of the VLAN tag in the frame header that identifies an explicit VLAN. 
Port VLAN identifier (PVID)—a classification mechanism that associates a port with a specific VLAN. For example, a port with a PVID of 3 (PVID =3) assigns all untagged frames received on this port to VLAN 3. Any untagged frames received by the switch are classified with the PVID of the receiving port. 
Tagged frame—a frame that carries VLAN tagging information in the header. This VLAN tagging information is a 32‐bit field (VLAN tag) in the frame header that identifies the frame as belonging to a specific VLAN. Untagged frames are marked (tagged) with this classification as they leave the switch through a port that is configured as a tagged port.

Untagged frame— a frame that does not carry any VLAN tagging information in the frame header.

Untagged member—a port that has been configured as an untagged member of a specific VLAN. When an untagged frame exits the switch through an untagged member port, the frame header remains unchanged. When a tagged frame exits the switch through an untagged member port, the tag is stripped and the tagged frame is changed to an untagged frame.

Tagged member—a port that has been configured as a tagged member of a specific VLAN. When an untagged frame exits the switch through a tagged member port, the frame header is modified to include the 32‐bit tag associated with the PVID. When a tagged frame exits the switch through a tagged member port, the frame header remains unchanged (original VID remains). When an access port is set as a trunk, it is automatically added to all data VLANs. To change the allowed VLAN range, use the command:
switchport trunk allowed vlans <range>
Note: If a 802.1Q tagged frame is received by a port that has VLAN‐tagging disabled and the port VLAN ID (PVID) is different than the VLAN ID of the packet, then the frame is dropped at the ingress port. 148
G8052 Application Guide for ENOS 8.4
Figure 2. Default VLAN settings
802.1Q Switch
VLAN 1
Port 1
Port 2
Port 3
Port 4
Port 5
Port 6
Port 7
...
PVID = 1
DA
CRC
SA
Incoming
untagged
packet
Outgoing
untagged packet
(unchanged)
Data
CRC
Data
SA
DA
Key
By default:
All ports are assigned PVID = 1
All ports are untagged members of VLAN 1
BS45010A
Note: The port numbers specified in these illustrations may not directly correspond to the physical port configuration of your switch model.
When a VLAN is configured, ports are added as members of the VLAN, and the ports are defined as either tagged or untagged (see Figure 3 through Figure 6).
The default configuration settings for the G8052 has all ports set as untagged members of VLAN 1 with all ports configured as PVID = 1. In the default configuration example shown in Figure 2, all incoming packets are assigned to VLAN 1 by the default port VLAN identifier (PVID =1). Figure 3 through Figure 6 illustrate generic examples of VLAN tagging. In Figure 3, untagged incoming packets are assigned directly to VLAN 2 (PVID = 2). Port 5 is configured as a tagged member of VLAN 2, and port 7 is configured as an untagged member of VLAN 2. Note: The port assignments in the following figures are not meant to match the G8052. Figure 3. Port‐based VLAN assignment
Data
SA
Before
DA
Port 2
Port 3
802.1Q Switch
Port 6
Port 7
Tagged member
of VLAN 2
Port 5
CRC
Port 1
Port 4
PVID = 2
Untagged packet
Port 8
Untagged member
of VLAN 2
© Copyright Lenovo 2016
Chapter 9: VLANs
149
As shown in Figure 4, the untagged packet is marked (tagged) as it leaves the switch through port 5, which is configured as a tagged member of VLAN 2. The untagged packet remains unchanged as it leaves the switch through port 7, which is configured as an untagged member of VLAN 2.
Figure 4. 802.1Q tagging (after port‐based VLAN assignment) Port 4
Port 1
Port 2
Tagged member
of VLAN 2
Port 3
Port 5
PVID = 2
802.1Q Switch
Port 6
Untagged memeber
of VLAN 2
Port 7
CRC*
Data
Tag
SA
DA
(*Recalculated)
Port 8
CRC
8100
Priority
CFI
VID = 2
16 bits
3 bits
1 bits
12 bits
Data
After
Outgoing
untagged packet
(unchanged)
SA
Key
DA
Priority
CFI
VID
- User_priority
- Canonical format indicator
- VLAN identifier
BS45012A
In Figure 5, tagged incoming packets are assigned directly to VLAN 2 because of the tag assignment in the packet. Port 5 is configured as a tagged member of VLAN 2, and port 7 is configured as an untagged member of VLAN 2.
Figure 5. 802.1Q tag assignment
Port 1
PVID = 2
Port 2
Port 3
Data
Tag
SA
Before
DA
802.1Q Switch
Port 6
Port 7
Tagged member
of VLAN 2
Port 5
CRC
Port 4
Tagged packet
Port 8
Untagged member
of VLAN 2
BS45013A
As shown in Figure 6, the tagged packet remains unchanged as it leaves the switch through port 5, which is configured as a tagged member of VLAN 2. However, the tagged packet is stripped (untagged) as it leaves the switch through port 7, which is configured as an untagged member of VLAN 2. 150
G8052 Application Guide for ENOS 8.4
Figure 6. 802.1Q tagging (after 802.1Q tag assignment)
Port 4
Port 1
Port 2
802.1Q Switch
Port 6
Untagged member
of VLAN 2
Port 7
CRC*
Tagged member
of VLAN 2
Port 3
Port 5
PVID = 2
CRC
Data
Tag
SA
DA
Port 8
(*Recalculated)
8100
Priority
CFI
VID = 2
16 bits
3 bits
1 bit
12 bits
Data
SA
DA
Outgoing
untagged packet
changed
(tag removed)
After
Key
Priority
CFI
VID
- User_priority
- Canonical format indicator
- VLAN identifier
BS45014A
Ingress VLAN Tagging
Tagging can be enabled on an ingress port. When a packet is received on an ingress port, and if ingress tagging is enabled on the port, a VLAN tag with the port PVID is inserted into the packet as the outer VLAN tag. Depending on the egress port setting (tagged or untagged), the outer tag of the packet is retained or removed when it leaves the egress port.
Ingress VLAN tagging is used to tunnel packets through a public domain without altering the original 802.1Q status.
When ingress tagging is enabled on a port, all packets, whether untagged or tagged, will be tagged again. As shown in Figure 7, when tagging is enabled on the egress port, the outer tag of the packet is retained when it leaves the egress port. If tagging is disabled on the egress port, the outer tag of the packet is removed when it leaves the egress port.
© Copyright Lenovo 2016
Chapter 9: VLANs
151
Figure 7. 802.1Q tagging (after ingress tagging assignment) Untagged packet received on ingress port
802.1Q Switch
CRC
Data
SA
DA
Port 4
PVID = 2
Untagged packet
CRC*
Port 2
Data
Port 3
Tag
SA
Tagged member
of VLAN 2
DA
Port 5
Port 1
CRC*
Data
Tag
SA
DA
After
Before
Port 6
Port 7
Port 8
Untagged member
of VLAN 2
CRC
Data
SA
DA
Tagged packet received on ingress port
802.1Q Switch
Data Tag 1
SA
DA
Port 2
Port 3
CRC* Data Tag 1 Tag 2 SA
Tagged member
of VLAN 2
DA
Port 5
CRC*
Port 1
Port 4
PVID = 2
Tagged packet
CRC*
Data Tag 1 Tag 2 SA DA
After
Before
Port 6
Port 7
Port 8
Untagged member
of VLAN 2
CRC*
Data Tag 1
SA
DA
By default, ingress tagging is disabled. To enable ingress tagging on a port, use the following commands: RS G8052(config)# interface port <number>
RS G8052(config­if)# tagpvid­ingress
RS G8052(config­if)# exit
Limitations
Ingress tagging cannot be configured with the following features/configurations:
152

vNIC ports

VMready ports
G8052 Application Guide for ENOS 8.4
VLAN Topologies and Design Considerations
Note the following when working with VLAN topologies:

By default, the G8052 software is configured so that tagging/trunk mode is disabled on all ports. 
By default, the G8052 software is configured so that all data ports are members of VLAN 1. 
When using Spanning Tree, STG 2‐128 may contain only one VLAN unless Multiple Spanning‐Tree Protocol (MSTP) mode is used. With MSTP mode, STG 1 to 32 can include multiple VLANs. 
All ports involved in both aggregation and port mirroring must have the same VLAN configuration. If a port is on a LAG with a mirroring port, the VLAN configuration cannot be changed. For more information about aggregation, see Chapter 10, “Ports and Link Aggregation” and Chapter 41, “Port Mirroring.”
Multiple VLANs with Tagging/Trunk Mode Adapters
Figure 8 illustrates a network topology described in Note: on page 154 and the configuration example on page page 156. Figure 8. Multiple VLANs with VLAN‐Tagged Gigabit Adapters Enterprise
Routing Switch
Server 1
VLAN 1
Server 2
VLAN 1
Enterprise
Routing Switch
Server 3
VLAN 2
Server 4
VLAN 3
Server 5
VLAN 1, 2
The features of this VLAN are described in the following table. © Copyright Lenovo 2016
Chapter 9: VLANs
153
Table 14. Multiple VLANs Example
Component
Description
G8052 switch
This switch is configured with three VLANs that represent three different IP subnets. Five ports are connected downstream to servers. Two ports are connected upstream to routing switches. Uplink ports are members of all three VLANs, with VLAN tagging/trunk mode enabled. Server 1
This server is a member of VLAN 1 and has presence in only one IP subnet. The associated switch port is only a member of VLAN 1, so tagging/trunk mode is disabled. Server 2 This server is a member of VLAN 1 and has presence in only one IP subnet. The associated switch port is only a member of VLAN 1, so tagging/trunk mode is disabled. Server 3
This server belongs to VLAN 2, and it is logically in the same IP subnet as Server 5. The associated switch port has tagging/trunk mode disabled. Server 4
A member of VLAN 3, this server can communicate only with other servers via a router. The associated switch port has tagging/trunk mode disabled. Server 5
A member of VLAN 1 and VLAN 2, this server can communicate only with Server 1, Server 2, and Server 3. The associated switch port has tagging/trunk mode enabled. Enterprise Routing switches
These switches must have all three VLANs (VLAN 1, 2, 3) configured. They can communicate with Server 1, Server 2, and Server 5 via VLAN 1. They can communicate with Server 3 and Server 5 via VLAN 2. They can communicate with Server 4 via VLAN 3. Tagging/trunk mode on switch ports is enabled. Note: VLAN tagging/trunk mode is required only on ports that are connected to other switches or on ports that connect to tag‐capable end‐stations, such as servers with VLAN‐tagging/trunk mode adapters. To configure a specific VLAN on a trunk port, the following conditions must be met:
The port must be in trunk mode.
The VLAN must be in the trunk’s allowed VLAN range. By default, the range includes all VLANs.
 The VLAN must be un‐reserved.
 The VLAN must be created.


The order in which these conditions are met is not relevant. However, all conditions must be met collectively. When all the conditions are met, the VLAN is enabled on the port. If one of the conditions is broken, the VLAN is disabled.
154
G8052 Application Guide for ENOS 8.4
If a port’s native VLAN is a private VLAN and its allowed VLAN range contains only invalid VLANs (either reserved VLANs or VLANs the port cannot belong to), removing the private VLAN mapping from the port will add the port to default VLAN and add the default VLAN to the allowed VLAN range.
When setting up multiple VLANs, ports configured in private VLAN mode are not added to private VLANs unless the private VLANs are also configured for those ports.
© Copyright Lenovo 2016
Chapter 9: VLANs
155
VLAN Configuration Example
Use the following procedure to configure the example network shown in Figure 8 on page 153. 1. Enable VLAN tagging/trunk mode on server ports that support multiple VLANs. RS
RS
RS
RS
G8052(config)# interface port 5
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlans 1,2
G8052(config­if)# exit
2. Enable tagging/trunk mode on uplink ports that support multiple VLANs. RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface port 19
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan add 2,3
G8052(config­if)# exit
G8052(config)# interface port 20
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan add 2,3
G8052(config­if)# exit
3. Configure server ports that belong to a single VLAN. RS G8052(config)# interface port 4
RS G8052(config­if)# switchport access vlan 2
RS G8052(config­if)# exit
By default, all ports are members of VLAN 1, so configure only those ports that belong to other VLANs. 156
G8052 Application Guide for ENOS 8.4
Protocol-Based VLANs
Protocol‐based VLANs (PVLANs) allow you to segment network traffic according to the network protocols in use. Traffic for supported network protocols can be confined to a particular port‐based VLAN. You can give different priority levels to traffic generated by different network protocols.
With PVLAN, the switch classifies incoming packets by Ethernet protocol of the packets, not by the configuration of the ingress port. When an untagged or priority‐tagged frame arrives at an ingress port, the protocol information carried in the frame is used to determine a VLAN to which the frame belongs. If a frame’s protocol is not recognized as a pre‐defined PVLAN type, the ingress port’s PVID is assigned to the frame. When a tagged frame arrives, the VLAN ID in the frame’s tag is used.
Each VLAN can contain up to eight different PVLANs. You can configure separate PVLANs on different VLANs, with each PVLAN segmenting traffic for the same protocol type. For example, you can configure PVLAN 1 on VLAN 2 to segment IPv4 traffic, and PVLAN 8 on VLAN 100 to segment IPv4 traffic.
To define a PVLAN on a VLAN, configure a PVLAN number (1‐8) and specify the frame type and the Ethernet type of the PVLAN protocol. You must assign at least one port to the PVLAN before it can function. Define the PVLAN frame type and Ethernet type as follows:


Frame type—consists of one of the following values:

Ether2 (Ethernet II)

SNAP (Subnetwork Access Protocol)

LLC (Logical Link Control)
Ethernet type—consists of a 4‐digit (16 bit) hex value that defines the Ethernet type. You can use common Ethernet protocol values, or define your own values. Following are examples of common Ethernet protocol values:

IPv4 = 0800

IPv6 = 86dd

ARP = 0806
Port-Based vs. Protocol-Based VLANs
Each VLAN supports both port‐based and protocol‐based association, as follows:
© Copyright Lenovo 2016

The default VLAN configuration is port‐based. All data ports are members of VLAN 1, with no PVLAN association.

When you add ports to a PVLAN, the ports become members of both the port‐based VLAN and the PVLAN. For example, if you add port 1 to PVLAN 1 on VLAN 2, the port also becomes a member of VLAN 2.

When you delete a PVLAN, it’s member ports remain members of the port‐based VLAN. For example, if you delete PVLAN 1 from VLAN 2, port 1 remains a member of VLAN 2.

When you delete a port from a VLAN, the port is deleted from all corresponding PVLANs.
Chapter 9: VLANs
157
PVLAN Priority Levels
You can assign each PVLAN a priority value of 0‐7, used for Quality of Service (QoS). PVLAN priority takes precedence over a port’s configured priority level. If no priority level is configured for the PVLAN (priority = 0), each port’s priority is used (if configured).
All member ports of a PVLAN have the same PVLAN priority level.
PVLAN Tagging/Trunk Mode
When PVLAN tagging is enabled, the switch tags frames that match the PVLAN protocol. For more information about tagging, see “VLAN Tagging/Trunk Mode” on page 148.
Untagged ports must have PVLAN tagging disabled. Tagged ports can have PVLAN tagging either enabled or disabled.
PVLAN tagging has higher precedence than port‐based tagging. If a port is tagging/trunk mode enabled, and the port is a member of a PVLAN, the PVLAN tags egress frames that match the PVLAN protocol.
Use the tag list command (protocol­vlan <x> tag­pvlan) to define the complete list of tag‐enabled ports in the PVLAN. Note that all ports not included in the PVLAN tag list will have PVLAN tagging disabled.
PVLAN Configuration Guidelines
Consider the following guidelines when you configure protocol‐based VLANs:
158

Each port can support up to 16 VLAN protocols.

The G8052 can support up to 16 protocols simultaneously.

Each PVLAN must have at least one port assigned before it can be activated.

The same port within a port‐based VLAN can belong to multiple PVLANs.

An untagged port can be a member of multiple PVLANs.

A port cannot be a member of different VLANs with the same protocol association.
G8052 Application Guide for ENOS 8.4
Configuring PVLAN
Follow this procedure to configure a Protocol‐based VLAN (PVLAN).
1. Configure VLAN tagging/trunk mode for ports.
RS G8052(config)# interface port 1, 2
RS G8052(config­if)# switchport mode trunk
RS G8052(config­if)# exit
2. Create a VLAN and define the protocol type(s) supported by the VLAN.
RS G8052(config)# vlan 2
RS G8052(config­vlan)# protocol­vlan 1 frame­type ether2 0800
3. Configure the priority value for the protocol.
RS G8052(config­vlan)# protocol­vlan 1 priority 2
4. Add member ports for this PVLAN.
RS G8052(config­vlan)# protocol­vlan 1 member 1, 2
Note: If VLAN tagging is turned on and the port being added to the VLAN has a different default VLAN (PVID/Native VLAN), you will be asked to confirm changing the PVID to the current VLAN.
5. Enable the PVLAN.
RS G8052(config­vlan)# protocol­vlan 1 enable
RS G8052(config­vlan)# exit
6. Verify PVLAN operation. RS G8052(config)# show vlan
VLAN Name Status Ports
­­­­ ­­­­­­­­­­­­­­­­­­­­­­­­ ­­­­­­ ­­­­­­­­­­­­­­­­­­­­­­­­­
1 Default VLAN ena 1­48, XGE1­XGE4
2 VLAN 2 ena 1 2
PVLAN Protocol FrameType EtherType Priority Status Ports
­­­­­ ­­­­­­­­ ­­­­­­­­­­ ­­­­­­­­­ ­­­­­­­­ ­­­­­­­ ­­­­­­­­­­­
2 1 Ether2 0800 2 enabled 1 2
PVLAN PVLAN­Tagged Ports
­­­­­ ­­­­­­­­­­­­­­­­­­­­­­­­­­­
none none
© Copyright Lenovo 2016
Chapter 9: VLANs
159
Private VLANs
Private VLANs provide Layer 2 isolation between the ports within the same broadcast domain. Private VLANs can control traffic within a VLAN domain, and provide port‐based security for host servers. Use Private VLANs to partition a VLAN domain into sub‐domains. Each sub‐domain is comprised of one primary VLAN and one or more secondary VLANs, as follows: Primary VLAN—carries unidirectional traffic downstream from promiscuous ports. Each Private VLAN configuration has only one primary VLAN. All ports in the Private VLAN are members of the primary VLAN.  Secondary VLAN—Secondary VLANs are internal to a private VLAN domain, and are defined as follows: 

Isolated VLAN—carries unidirectional traffic upstream from the host servers toward ports in the primary VLAN. Each Private VLAN configuration can contain only one isolated VLAN. 
Community VLAN—carries upstream traffic from ports in the community VLAN to other ports in the same community, and to ports in the primary VLAN. Each Private VLAN configuration can contain multiple community VLANs. After you define the primary VLAN and one or more secondary VLANs, you map the secondary VLAN(s) to the primary VLAN. Private VLAN Ports
Private VLAN ports are defined as follows: Promiscuous—A promiscuous port is a port that belongs to the primary VLAN. The promiscuous port can communicate with all the interfaces, including ports in the secondary VLANs (Isolated VLAN and Community VLANs).
 Isolated—An isolated port is a host port that belongs to an isolated VLAN. Each isolated port has complete layer 2 separation from other ports within the same private VLAN (including other isolated ports), except for the promiscuous ports. 

160

Traffic sent to an isolated port is blocked by the Private VLAN, except the traffic from promiscuous ports. 
Traffic received from an isolated port is forwarded only to promiscuous ports. Community—A community port is a host port that belongs to a community VLAN. Community ports can communicate with other ports in the same com‐
munity VLAN, and with promiscuous ports. These interfaces are isolated at layer 2 from all other interfaces in other communities and from isolated ports within the Private VLAN.
G8052 Application Guide for ENOS 8.4
Configuration Guidelines
The following guidelines apply when configuring Private VLANs: 
The default VLAN 1 cannot be a Private VLAN. 
IGMP Snooping must be disabled on Private VLANs.

All VLANs that comprise the Private VLAN must belong to the same Spanning Tree Group. Configuration Example
Follow this procedure to configure a Private VLAN. 1. Select a VLAN and define the Private VLAN type as primary. RS G8052(config)# vlan 700
RS G8052(config­vlan)# private­vlan primary
RS G8052(config­vlan)# exit
2. Configure a promiscuous port for VLAN 700. RS
RS
RS
RS
G8052(config)# interface port 1
G8052(config­if)# switchport mode private­vlan
G8052(config­if)# switchport private­vlan mapping 700
G8052(config­if)# exit
3. Configure two secondary VLANs: isolated VLAN and community VLAN. RS
RS
RS
RS
RS
RS
G8052(config)# vlan 701
G8052(config­vlan)# private­vlan isolated
G8052(config­vlan)# exit
G8052(config)# vlan 702
G8052(config­vlan)# private­vlan community
G8052(config­vlan)# exit
4. Map secondary VLANs to primary VLAN. RS
RS
RS
RS
RS
RS
G8052(config)# vlan 700­702
G8052(config­vlan)# stg 1
G8052(config­vlan)# exit
G8052(config)# vlan 700
G8052(config­vlan)# private­vlan association 701,702
G8052(config­vlan)# exit
5. Configure host ports for secondary VLANs. © Copyright Lenovo 2016
RS
RS
RS
RS
G8052(config)# interface port 2
G8052(config­if)# switchport mode private­vlan
G8052(config­if)# switchport private­vlan host­association 700 701
G8052(config­if)# exit
RS
RS
RS
RS
G8052(config)# interface port 3
G8052(config­if)# switchport mode private­vlan
G8052(config­if)# switchport private­vlan host­association 700 702
G8052(config­if)# exit
Chapter 9: VLANs
161
6. Verify the configuration. RS G8052(config)# show vlan private­vlan
Primary Secondary Type Ports
­­­­­­­ ­­­­­­­­­ ­­­­­­­­­­­­­­­ ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
700 701 isolated 1 2
700 702 community 1 3 162
G8052 Application Guide for ENOS 8.4
Chapter 10. Ports and Link Aggregation
Link Aggregation (LAG) groups can provide super‐bandwidth, multi‐link connections between the G8052 and other LAG‐capable devices. A LAG is a group of ports that act together, combining their bandwidth to create a single, larger virtual link. This chapter provides configuration background and examples for aggregating multiple ports together: © Copyright Lenovo 2016

“Aggregation Overview” on page 164”

“Configuring a Static LAG” on page 166

“Configurable LAG Hash Algorithm” on page 173

“Link Aggregation Control Protocol” on page 168
163
Aggregation Overview
When using LAGs between two switches, as shown in Figure 9, you can create a virtual link between the switches, operating with combined throughput levels that depends on how many physical ports are included.
Figure 9. Port LAG
Switch 1
Switch 2
LAG
LAGs are also useful for connecting a G8052 to third‐party devices that support link aggregation, such as Cisco routers and switches with EtherChannel technology (not ISL aggregation technology) and Sunʹs Quad Fast Ethernet Adapter. LAG technology is compatible with these devices when they are configured manually.
LAG traffic is statistically distributed among the ports in a LAG, based on a variety of configurable options.
Also, since each LAG is comprised of multiple physical links, the LAG is inherently fault tolerant. As long as one connection between the switches is available, the trunk remains active and statistical load balancing is maintained whenever a port in a LAG is lost or returned to service. 164
G8052 Application Guide for ENOS 8.4
Static LAGs
When you create and enable a static LAG, the LAG members (switch ports) take on certain settings necessary for correct operation of the aggregation feature. Static LAG Requirements
Before you configure your LAG, you must consider these settings, along with specific configuration rules, as follows:
1. Read the configuration rules provided in the section, “Static Aggregation Configuration Rules” on page 166.
2. Determine which switch ports (up to 8) are to become LAG members (the specific ports making up the LAG). 3. Ensure that the chosen switch ports are set to enabled. LAG member ports must have the same VLAN and Spanning Tree configuration.
4. Consider how the existing Spanning Tree will react to the new LAG configuration. See Chapter 11, “Spanning Tree Protocols,” for Spanning Tree Group configuration guidelines.
5. Consider how existing VLANs will be affected by the addition of a LAG.
© Copyright Lenovo 2016
Chapter 10: Ports and Link Aggregation
165
Static Aggregation Configuration Rules
The aggregation feature operates according to specific configuration rules. When creating LAGs, consider the following rules that determine how a LAG reacts in any network topology:











All links must originate from one logical device, and lead to one logical destina‐
tion device. Usually, a LAG connects two physical devices together with multiple links. However, in some networks, a single logical device may include multiple physical devices or when using VLAGs (see Chapter 12, “Virtual Link Aggrega‐
tion Groups). In such cases, links in a LAG are allowed to connect to multiple physical devices because they act as one logical device.
Any physical switch port can belong to only one LAG.
Aggregation from third‐party devices must comply with Cisco® EtherChannel® technology.
All LAG member ports must be assigned to the same VLAN configuration before the LAG can be enabled.
When an active port is configured in a LAG, the port becomes a LAG member when you enable the LAG. The Spanning Tree parameters for the port then change to reflect the new LAG settings.
All LAG members must be in the same Spanning Tree Group (STG) and can belong to only one Spanning Tree Group (STG). However if all ports are tagged, then all LAG ports can belong to multiple STGs. If you change the Spanning Tree participation of any LAG member to enabled or disabled, the Spanning Tree participation of all LAG members changes sim‐
ilarly. When a LAG is enabled, the LAG’s Spanning Tree participation setting takes pre‐
cedence over that of any LAG member. You cannot configure a LAG member as a monitor port in a port‐mirroring con‐
figuration.
LAGs cannot be monitored by a monitor port; however, LAG members can be monitored.
All ports in static LAGs must be have the same link configuration (speed, duplex, flow control). Configuring a Static LAG
In the following example, three ports are aggregated between two switches.
Figure 10. LAG Configuration Example 2
1
166
LAG 3
9 16
LAG 3 combines
Ports 2, 9, and 16
11 18
LAG 1
LAG 1 combines
Ports 1, 11, and 18
G8052 Application Guide for ENOS 8.4
Prior to configuring each switch in this example, you must connect to the appropriate switches as the administrator.
Note: For details about accessing and using any of the commands described in this example, see the Lenovo RackSwitch G8052 ISCLI Reference.
1. Follow these steps on the G8052: a. Define a LAG.
RS G8052(config)# portchannel 3 port 2,9,16
RS G8052(config)# portchannel 3 enable
b. Verify the configuration.
# show portchannel information
Examine the resulting information. If any settings are incorrect, make appropriate changes.
2. Repeat the process on the other switch.
RS G8052(config)# portchannel 1 port 1,11,18
RS G8052(config)# portchannel 1 enable
3. Connect the switch ports that will be members in the LAG. LAG 3 (on the G8052) is now connected to LAG 1 (on the other switch). Note: In this example, two G8052 switches are used. If a third‐party device support‐
ing link aggregation is used (such as Cisco routers and switches with EtherChannel technology or Sunʹs Quad Fast Ethernet Adapter), LAGs on the third‐party device must be configured manually. Connection problems could arise when using auto‐
matic LAG negotiation on the third‐party device. 4. Examine the aggregation information on each switch.
# show portchannel information
PortChannel 3: Enabled
Protocol—Static
port state:
2: STG 1 forwarding
9: STG 1 forwarding
16: STG 1 forwarding
Information about each port in each configured LAG is displayed. Make sure that LAGs consist of the expected ports and that each port is in the expected state.
The following restrictions apply: © Copyright Lenovo 2016

Any physical switch port can belong to only one LAG.

Up to 8 ports can belong to the same LAG.

All ports in static LAGs must be have the same link configuration (speed, duplex, flow control). 
Aggregation with third‐party devices must comply with Cisco® EtherChannel® technology.
Chapter 10: Ports and Link Aggregation
167
Link Aggregation Control Protocol
Link Aggregation Control Protocol (LACP) is an IEEE 802.3ad standard for grouping several physical ports into one logical port (known as a Link Aggregation group) with any device that supports the standard. Please refer to IEEE 802.3ad‐2002 for a full description of the standard. The 802.3ad standard allows standard Ethernet links to form a single Layer 2 link using Link Aggregation Control Protocol (LACP). Link aggregation is a method of grouping physical link segments of the same media type and speed in full duplex, and treating them as if they were part of a single, logical link segment. If a link in an LACP LAG fails, traffic is reassigned dynamically to the remaining link(s) of the dynamic LAG. Note: LACP implementation in the Lenovo Enterprise Network Operating System does not support the Churn machine, an option used to detect if the port is operable within a bounded time period between the actor and the partner. Only the Marker Responder is implemented, and there is no marker protocol generator. A port’s Link Aggregation Identifier (LAG ID) determines how the port can be aggregated. The Link Aggregation ID (LAG ID) is constructed mainly from the partner switch’s system ID and the port’s admin key, as follows: 
System ID: an integer value based on the partner switch’s MAC address and the system priority assigned in the CLI. 
Admin key: a port’s Admin key is an integer value (1‐65535) that you can configure in the CLI. Each switch port that participates in the same LACP LAG must have the same admin key value. The Admin key is local significant, which means the partner switch does not need to use the same Admin key value. For example, consider two switches, an Actor (the G8052) and a Partner (another switch), as shown in Table 15.
Table 15. Actor vs. Partner LACP configuration
Actor Switch
Partner Switch
LACP LAG
Port 7 (admin key = 100)
Port 1 (admin key = 50)
Primary LAG
Port 8 (admin key = 100)
Port 2 (admin key = 50)
Primary LAG
Port 9 (admin key = 100)
Port 3 (admin key = 70)
Secondary LAG
Port 10 (admin key = 100) Port 4 (admin key = 70)
Secondary LAG
In the configuration shown in Table 15, Actor switch ports 7 and 8 aggregate to form an LACP LAG with Partner switch ports 1 and 2. Only ports with the same LAG ID are aggregated in the LAG. Actor switch ports 9 and 10 are not aggregated in the same LAG, because although they have the same admin key on the Actor switch, their LAG IDs are different (due to a different Partner switch admin key configuration). Instead, they form a secondary LAG with Partner switch ports 3 and 4.
LACP automatically determines which member links can be aggregated and then aggregates them. It provides for the controlled addition and removal of physical links for the link aggregation. 168
G8052 Application Guide for ENOS 8.4
Static LACP LAGs
To prevent switch ports with the same admin key from forming multiple LAGs, you can configure the LACP LAG as static. In a static LACP LAG, ports with the same admin key, but with different LAG IDs, compete to get aggregated in a LAG. The LAG ID for the LAG is decided based on the first port that is aggregated in the group. Ports with this LAG ID get aggregated and the other ports are placed in suspended mode. As per the configuration shown in Table 15 on page 168, if port 7 gets aggregated first, then the LAG ID of port 7 would be the LAG ID of the LAG. Port 8 will join the LAG while ports 9 and 10 would be placed in suspended mode. When in suspended mode, a port transmits only LACP data units (LACPDUs) and discards all other traffic.
A port may also be placed in suspended mode for the following reasons:

When LACP is configured on the port but it stops receiving LACPDUs from the partner switch.

When the port has a different LAG ID because of the partner switch MAC or port LACP key being different. For example: when a switch is connected to two partners.
Static LACP LAGs are configured by associating the LACP admin key to a portchannel ID within a dedicated LACP portchannel group range: RS G8052(config)# portchannel <53‐104> lacp key <adminkey of the LAG> LACP Port Modes
Each port on the switch can have one of the following LACP modes.

off (default)
You can configure this port into a regular static LAG. 
active
The port is capable of forming an LACP LAG. This port sends LACPDU packets to partner system ports. 
passive
The port is capable of forming an LACP LAG. This port only responds to the LACPDU packets sent from an LACP active port.
Each active LACP port transmits LACP data units (LACPDUs), while each passive LACP port listens for LACPDUs. During LACP negotiation, the admin key is exchanged. The LACP LAG is enabled as long as the information matches at both ends of the link. If the admin key value changes for a port at either end of the link, that port’s association with the LACP LAG is lost. When the system is initialized, all ports by default are in LACP off mode and are assigned unique admin keys. To make a group of ports aggregable, you assign them all the same admin key. You must set the port’s LACP mode to active to activate LACP negotiation. You can set other port’s LACP mode to passive to reduce the amount of LACPDU traffic at the initial LAG‐forming stage. © Copyright Lenovo 2016
Chapter 10: Ports and Link Aggregation
169
Use the following command to check whether the ports are aggregated: RS G8052 # show lacp information Notes:

If you configure LACP on ports with 802.1X network access control, make sure the ports on both sides of the connection are properly configured for both LACP and 802.1X.

IEEE 802.1x and LACP cannot both be enabled on port 1.
LACP Individual
Ports with LACP enabled (active or passive) are prevented by default from forming individual links if they cannot join an LACP LAG. To override this behavior, use the following commands: RS G8052(config) # interface port <port no. or range>
RS G8052(config­if) # no lacp suspend­individual
This allows the selected ports to be treated as normal link‐up ports, which may forward data traffic according to STP, Hot Links or other applications, if they do not receive any LACPDUs.
To configure the LACP individual setting for all the ports in a static LACP LAG, use the following commands:
RS G8052(config)# interface portchannel lacp <adminkey of the LAG> RS G8052(config­PortChannel)# [no] lacp suspend­individual
Note: By default, external ports are configured with the command lacp suspend­individual, while internal ports are configured with the command no lacp suspend­individual.
LACP Minimum Links Option
For dynamic LAGs that require a guaranteed amount of bandwidth to be considered useful, you can specify the minimum number of links for the LAG. If the specified minimum number of ports is not available, the LAG link will not be established. If an active LACP LAG loses one or more component links, the LAG will be placed in the down state if the number of links falls to less than the specified minimum. By default, the minimum number of links is 1, meaning that LACP LAGs will remain operational as long as at least one link is available.
The LACP minimum links setting can be configured as follows:

Interface (port) configuration mode:
RS G8052(config)# interface port <port number or range>
RS G8052(config­if)# port­channel min­links <minimum links>
RS G8052(config­if)# exit
170
G8052 Application Guide for ENOS 8.4

Portchannel configuration mode:
RS G8052(config)# interface portchannel lacp <LACP key>
RS G8052(config­PortChannel)# port­channel min­links <minimum links>
RS G8052(config­if)# exit
LACP Configuration Guidelines
Consider the following guidelines when you configure LACP LAGs: © Copyright Lenovo 2016

The range of potential LACP LAG IDs is 53‐104. 
Each port that is configured to participate in LACP must be set to full duplex. Chapter 10: Ports and Link Aggregation
171
Configuring LACP
Use the following procedure to configure LACP for ports 7, 8, 9 and 10 to participate in link aggregation. 1. Configure port parameters. All ports that participate in the LACP LAG must have the same settings, including VLAN membership. 2. Select the port range and define the admin key. Only ports with the same admin key can form an LACP LAG. RS G8052(config)# interface port 7­10
RS G8052(config­if)# lacp key 100
3. Set the LACP mode. RS G8052(config­if)# lacp mode active
4. Optionally allow member ports to individually participate in normal data traffic if no LACPDUs are received.
RS G8052(config­if)# no lacp suspend­individual
RS G8052(config­if)# exit
5. Set the link aggregation as static, by associating it with LAG ID 65:
RS G8052(config)# portchannel 65 lacp key 100
172
G8052 Application Guide for ENOS 8.4
Configurable LAG Hash Algorithm
Traffic in a LAG is statistically distributed among member ports using a hash process where various address and attribute bits from each transmitted frame are recombined to specify the particular LAG port the frame will use.
Packet-Based LAG Hashing
The switch can be configured to use a variety of hashing options. To achieve the most even traffic distribution, select options that exhibit a wide range of values for your particular network. Avoid hashing on information that is not usually present in the expected traffic, or which does not vary.
The G8052 supports the following hashing options, which can be used in any combination:

Frame MAC and IP information. One of the following combinations is required:

Source MAC address (smac)
RS G8052(config)# portchannel hash source­mac­address

Destination MAC address (dmac)
RS G8052(config)# portchannel hash destination­mac­address

Both source and destination MAC address
RS G8052(config)# portchannel hash source­destination­mac

IPv4/IPv6 source IP address (sip)
RS G8052(config)# portchannel hash source­ip­address

IPv4/IPv6 destination IP address (dip)
RS G8052(config)# portchannel hash destination­ip­address

Both source and destination IPv4/IPv6 address (enabled by default)
RS G8052(config)# portchannel hash source­destination­ip
© Copyright Lenovo 2016
Chapter 10: Ports and Link Aggregation
173

Ingress port number (disabled by default)
RS G8052(config)# portchannel hash ingress

Layer 4 port information (disabled by default)
RS G8052(config)# portchannel hash L4port
When enabled, Layer 4 port information (TCP, UPD, etc.) is added to the hash if available. The L4port option is ignored when Layer 4 information is not included in the packet (such as for Layer 2 packets). Port-Based LAG Hashing
The standard hashing process that determines where traffic in a LAG is distributed among member ports uses address and attribute bits from each transmitted frame to specify which LAG port the frame will use for egress. With port‐based LAG hashing, packet data is disregarded. Instead, you configure each ingress port to use a specific egress port. When you have many ingress ports with traffic to distribute over a smaller number of egress ports with equal bandwidth, such as 40 10Gb ingress ports and four 100Gb egress ports, this may enable you to make better use of those egress ports.
Note: Port‐based LAG hashing is disabled by default and the standard hashing algorithm is used.
To enable port‐based LAG hashing:
1. Enable or disable the feature on a per‐LAG basis.

For static LAGs:
RS G8052(config)# [no] portchannel hash static­distribution in­port portchannel <LAG ID>

Or for dynamic LAGs:
RS G8052(config)# [no] portchannel hash static­distribution in­port lacp­key <admin key>
2. For each port, specify its member hash index.
RS G8052(config)# interface port <port, list, or range>
RS G8052(config­if)# port­channel distribution trunk­member­index <1‐8>
RS G8052(config­if)# exit
The trunk‐member index will only be used for traffic destined for a LAG where port‐based LAG hashing has been enabled. Otherwise, the value is ignored.
When applicable, the index specifies which member link within the LAG will be used. Traffic from ports that have the same member index will occupy the same links when destined for the same LAG.
Note: The administrator must ensure that traffic is properly balanced among the individual links within the LAG.
174
G8052 Application Guide for ENOS 8.4
At any time, if a port’s member index is greater than the number of links available within a LAG where port‐based hashing is enabled, a modulus approach is used. For instance, if there are four members in the LAG, traffic from a port with a LAG‐member index of 1 will use the first link in the LAG, index 2 will use the second link, 3 will use the third, 4 will start again at the first link, 5 at the second, 6 at the thirds, and so on.
Each time a port is added to or removed from a LAG, the mapping between its member index and physical links is updated.
The LAG‐member index can be configured on a per‐port basis. The index assigned a given port is used with all LAGs where port‐based LAG hashing is enabled. The same port cannot use different LAG‐member indexes for different LAGs.
© Copyright Lenovo 2016
Chapter 10: Ports and Link Aggregation
175
176
G8052 Application Guide for ENOS 8.4
Chapter 11. Spanning Tree Protocols
When multiple paths exist between two points on a network, Spanning Tree Protocol (STP), or one of its enhanced variants, can prevent broadcast loops and ensure that the RackSwitch G8052 uses only the most efficient network path.
This chapter covers the following topics:
© Copyright Lenovo 2016

“Spanning Tree Protocol Modes” on page 178

“Global STP Control” on page 179

“PVRST Mode” on page 179

“Rapid Spanning Tree Protocol” on page 191

“Multiple Spanning Tree Protocol” on page 193

“Port Type and Link Type” on page 197
177
Spanning Tree Protocol Modes
Lenovo Enterprise Network Operating System 8.4 supports the following STP modes:

Rapid Spanning Tree Protocol (RSTP)
IEEE 802.1D (2004) RSTP allows devices to detect and eliminate logical loops in a bridged or switched network. When multiple paths exist, STP configures the network so that only the most efficient path is used. If that path fails, STP automatically configures the best alternative active path on the network to sustain network operations. RSTP is an enhanced version of IEEE 802.1D (1998) STP, providing more rapid convergence of the Spanning Tree network path states on STG 1.
See “Rapid Spanning Tree Protocol” on page 191 for details.

Per‐VLAN Rapid Spanning Tree (PVRST)
PVRST mode is based on RSTP to provide rapid Spanning Tree convergence, but supports instances of Spanning Tree, allowing one STG per VLAN. PVRST mode is compatible with Cisco R‐PVST/R‐PVST+ mode.
PVRST is the default Spanning Tree mode on the G8052. See “PVRST Mode” on page 179 for details.

Multiple Spanning Tree Protocol (MSTP)
IEEE 802.1Q (2003) MSTP provides both rapid convergence and load balancing in a VLAN environment. MSTP allows multiple STGs, with multiple VLANs in each.
See “Multiple Spanning Tree Protocol” on page 193 for details.
178
G8052 Application Guide for ENOS 8.4
Global STP Control
By default, the Spanning Tree feature is globally enabled on the switch, and is set for PVRST mode. Spanning Tree (and thus any currently configured STP mode) can be globally disabled using the following command: RS G8052(config)# spanning­tree mode disable
Spanning Tree can be re‐enabled by specifying the STP mode: RS G8052(config)# spanning­tree mode {pvrst|rstp|mst}
where the command options represent the following modes:
rstp:
pvrst:
 mst:


RSTP mode
PVRST mode
MSTP mode
PVRST Mode
Note: Per‐VLAN Rapid Spanning Tree (PVRST) is enabled by default on the G8052.
Using STP, network devices detect and eliminate logical loops in a bridged or switched network. When multiple paths exist, Spanning Tree configures the network so that a switch uses only the most efficient path. If that path fails, Spanning Tree automatically sets up another active path on the network to sustain network operations.
ENOS PVRST mode is based on IEEE 802.1w RSTP. Like RSTP, PVRST mode provides rapid Spanning Tree convergence. However, PVRST mode is enhanced for multiple instances of Spanning Tree. In PVRST mode, each VLAN may be automatically or manually assigned to one of 127 available STGs. If you need to assign a VLAN to STG 128, it must be done manually. Each STG acts as an independent, simultaneous instance of STP. PVRST uses IEEE 802.1Q tagging to differentiate STP BPDUs and is compatible with Cisco R‐PVST/R‐PVST+ modes.
The relationship between ports, LAGs, VLANs, and Spanning Trees is shown in Table 16.
Table 16. Ports, LAGs, and VLANs
Switch Element
Belongs To
Port
LAG or one or more VLANs
LAG
One or more VLANs
VLAN (non‐default)

PVRST: One VLAN per STG
RSTP: All VLANs are in STG 1
 MSTP: Multiple VLANs per STG

© Copyright Lenovo 2016
Chapter 11: Spanning Tree Protocols
179
Port States
The port state controls the forwarding and learning processes of Spanning Tree. In PVRST, the port state has been consolidated to the following: discarding, learning, and forwarding.
Due to the sequence involved in these STP states, considerable delays may occur while paths are being resolved. To mitigate delays, ports defined as edge ports (“Port Type and Link Type” on page 197) may bypass the discarding and learning states, and enter directly into the forwarding state.
Bridge Protocol Data Units
To create a Spanning Tree, the switch generates a configuration Bridge Protocol Data Unit (BPDU), which it then forwards out of its ports. All switches in the Layer 2 network participating in the Spanning Tree gather information about other switches in the network through an exchange of BPDUs.
How BPDU Works
A bridge sends BPDU packets at a configurable regular interval (2 seconds by default). The BPDU is used to establish a path, much like a hello packet in IP routing. BPDUs contain information about the transmitting bridge and its ports, including bridge MAC addresses, bridge priority, port priority, and path cost. If the ports are in trunk mode/tagged, each port sends out a special BPDU containing the tagged information.
The generic action of a switch on receiving a BPDU is to compare the received BPDU to its own BPDU that it will transmit. If the priority of the received BPDU is better than its own priority, it will replace its BPDU with the received BPDU. Then, the switch adds its own bridge ID number and increments the path cost of the BPDU. The switch uses this information to block any necessary ports.
Note: If STP is globally disabled, BPDUs from external devices will transit the switch transparently. If STP is globally enabled, for ports where STP is turned off, inbound BPDUs will instead be discarded.
Determining the Path for Forwarding BPDUs
When determining which port to use for forwarding and which port to block, the G8052 uses information in the BPDU, including each bridge ID. A technique based on the “lowest root cost” is then computed to determine the most efficient path for forwarding.
Bridge Priority
The bridge priority parameter controls which bridge on the network is the STG root bridge. To make one switch become the root bridge, configure the bridge priority lower than all other switches and bridges on your network. The lower the value, the higher the bridge priority. Use the following command to configure the bridge priority: RS G8052(config)# spanning­tree stp <STG number or range> bridge priority <0‐65535>
180
G8052 Application Guide for ENOS 8.4
Port Priority
The port priority helps determine which bridge port becomes the root port or the designated port. The case for the root port is when two switches are connected using a minimum of two links with the same path‐cost. The case for the designated port is in a network topology that has multiple bridge ports with the same path‐cost connected to a single segment, the port with the lowest port priority becomes the designated port for the segment. Use the following command to configure the port priority: RS G8052(config­if)# spanning­tree stp <STG number or range> priority <port priority>
where priority value is a number from 0 to 240, in increments of 16 (such as 0, 16, 32, and so on). If the specified priority value is not evenly divisible by 16, the value will be automatically rounded down to the nearest valid increment whenever manually changed in the configuration, or whenever a configuration file from a release prior to ENOS 6.5 is loaded.
Root Guard
The root guard feature provides a way to enforce the root bridge placement in the network. It keeps a new device from becoming root and thereby forcing STP re‐convergence. If a root‐guard enabled port detects a root device, that port will be placed in a blocked state.
You can configure the root guard at the port level using the following commands:
RS G8052(config)# interface port <port number>
RS G8052(config­if)# spanning­tree guard root
The default state is “none”, i.e. disabled.
Loop Guard
In general, STP resolves redundant network topologies into loop‐free topologies. The loop guard feature performs additional checking to detect loops that might not be found using Spanning Tree. STP loop guard ensures that a non‐designated port does not become a designated port.
To globally enable loop guard, enter the following command:
RS G8052(config)# spanning­tree loopguard
Note: The global loop guard command will be effective on a port only if the port‐level loop guard command is set to default as shown below:
RS G8052(config)# interface port <port number>
RS G8052(config­if)# no spanning­tree guard
To enable loop guard at the port level, enter the following command:
RS G8052(config)# interface port <port number>
RS G8052(config­if)# spanning­tree guard loop
The default state is “none” (disabled).
© Copyright Lenovo 2016
Chapter 11: Spanning Tree Protocols
181
Port Path Cost
The port path cost assigns lower values to high‐bandwidth ports, such as 10 Gigabit Ethernet, to encourage their use. The objective is to use the fastest links so that the route with the lowest cost is chosen. A value of 0 (the default) indicates that the default cost will be computed for an auto‐negotiated link or LAG speed.
Use the following command to modify the port path cost: RS G8052(config)# interface port <port number>
RS G8052(config­if)# spanning­tree stp <STG number or range> path­cost <path cost value> RS G8052(config­if)# exit
The port path cost can be a value from 1 to 200000000. Specify 0 for automatic path cost.
Simple STP Configuration
Figure 11 depicts a simple topology using a switch‐to‐switch link between two G8052 1 and 2. Figure 11. Spanning Tree Blocking a Switch‐to‐Switch Link Enterprise
Routing
Switches
Switch 1
Switch 2
x
STP
Blocks Link
Server
Server
Server
Server
To prevent a network loop among the switches, STP must block one of the links between them. In this case, it is desired that STP block the link between the Lenovo switches, and not one of the G8052 uplinks or the Enterprise switch LAG.
During operation, if one G8052 experiences an uplink failure, STP will activate the Lenovo switch‐to‐switch link so that server traffic on the affected G8052 may pass through to the active uplink on the other G8052, as shown in Figure 12.
182
G8052 Application Guide for ENOS 8.4
Figure 12. Spanning Tree Restoring the Switch‐to‐Switch Link Enterprise
Routing
Switches
Switch 1
Server
Uplink
Failure
STP
Restores Link
Server
Server
Switch 2
Server
In this example, port 10 on each G8052 is used for the switch‐to‐switch link. To ensure that the G8052 switch‐to‐switch link is blocked during normal operation, the port path cost is set to a higher value than other paths in the network. To configure the port path cost on the switch‐to‐switch links in this example, use the following commands on each G8052. RS G8052(config)# interface port 10
RS G8052(config­if)# spanning­tree stp 1 path­cost 60000
RS G8052(config­if)# exit
© Copyright Lenovo 2016
Chapter 11: Spanning Tree Protocols
183
Per-VLAN Spanning Tree Groups
PVRST mode supports a maximum of 128 STGs, with each STG acting as an independent, simultaneous instance of STP.
Multiple STGs provide multiple data paths which can be used for load‐balancing and redundancy. To enable load balancing between two G8052s using multiple STGs, configure each path with a different VLAN and then assign each VLAN to a separate STG. Since each STG is independent, they each send their own IEEE 802.1Q tagged Bridge Protocol Data Units (BPDUs).
Each STG behaves as a bridge group and forms a loop‐free topology. The default STG 1 may contain multiple VLANs (typically until they can be assigned to another STG). STGs 2‐128 may contain only one VLAN each.
Using Multiple STGs to Eliminate False Loops
Figure 13 shows a simple example of why multiple STGs are needed. In the figure, two ports on a G8052 are connected to two ports on an application switch. Each of the links is configured for a different VLAN, preventing a network loop. However, in the first network, since a single instance of Spanning Tree is running on all the ports of the G8052, a physical loop is assumed to exist, and one of the VLANs is blocked, impacting connectivity even though no actual loop exists.
Figure 13. Using Multiple Instances of Spanning Tree Group
False x
Loop
Switch 2
VLAN 30
VLAN 1
Switch 1
STG 1
VLAN 1
is active
STG 2
VLAN 30
is active
Application Switch
Application Switch
With a single Spanning Tree,
one link becomes blocked.
Using multiple STGs,
both links may be active.
In the second network, the problem of improper link blocking is resolved when the VLANs are placed into different Spanning Tree Groups (STGs). Since each STG has its own independent instance of Spanning Tree, each STG is responsible only for the loops within its own VLAN. This eliminates the false loop, and allows both VLANs to forward packets between the switches at the same time.
184
G8052 Application Guide for ENOS 8.4
VLANs and STG Assignment
In PVRST mode, up to 128 STGs are supported. Ports cannot be added directly to an STG. Instead, ports must be added as members of a VLAN, and the VLAN must then be assigned to the STG. STG 1 is the default STG. Although VLANs can be added to or deleted from default STG 1, the STG itself cannot be deleted from the system. By default, STG 1 is enabled and includes VLAN 1, which by default includes all switch ports
By default, all other STGs (STG 2 through 128) are enabled, though they initially include no member VLANs. VLANs must be assigned to STGs. By default, this is done automatically using VLAN Automatic STG Assignment (VASA), though it can also be done manually (see “Manually Assigning STGs” on page 185.
Note: VLAN assignment to STG 128 must be done manually.
When VASA is enabled (as by default), each time a new VLAN is configured, the switch will automatically assign that new VLAN to its own STG. Conversely, when a VLAN is deleted, if its STG is not associated with any other VLAN, the STG is returned to the available pool.
The specific STG number to which the VLAN is assigned is based on the VLAN number itself. For low VLAN numbers (1 through 128), the switch will attempt to assign the VLAN to its matching STG number. For higher numbered VLANs, the STG assignment is based on a simple modulus calculation; the attempted STG number will “wrap around,” starting back at the top of STG list each time the end of the list is reached. However, if the attempted STG is already in use, the switch will select the next available STG. If an empty STG is not available when creating a new VLAN, the VLAN is automatically assigned to default STG 1.
If ports are tagged, each tagged port sends out a special BPDU containing the tagged information. Also, when a tagged port belongs to more than one STG, the egress BPDUs are tagged to distinguish the BPDUs of one STG from those of another STG.
VASA is enabled by default, but can be disabled or re‐enabled using the following commands: RS G8052(config)# [no] spanning­tree stg­auto
If VASA is disabled, when you create a new VLAN, that VLAN automatically belongs to default STG 1. To place the VLAN in a different STG, assign it manually.
VASA applies only to PVRST mode and is ignored in RSTP and MSTP modes.
Manually Assigning STGs
You may manually assign VLANs to specific STGs, whether or not VASA is enabled.
1. If no VLANs exist (other than default VLAN 1), see “Guidelines for Creating VLANs” on page 186 for information about creating VLANs and assigning ports to them.
2. Assign the VLAN to an STG using one of the following methods:
© Copyright Lenovo 2016
Chapter 11: Spanning Tree Protocols
185

From the global configuration mode: RS G8052(config)# spanning­tree stp <STG numbers> vlan <VLANs> 
Or from within the VLAN configuration mode:
RS G8052(config)# vlan <VLAN numbers>
RS G8052(config­vlan)# stg <STG number>
RS G8052(config­vlan)# exit
When a VLAN is assigned to a new STG, the VLAN is automatically removed from its prior STG.
Note: For proper operation with switches that use Cisco PVST+, it is recommended that you create a separate STG for each VLAN.
Guidelines for Creating VLANs
Follow these guidelines when creating VLANs:

When you create a new VLAN, if VASA is enabled (the default), that VLAN is automatically assigned its own STG. If VASA is disabled, the VLAN automatically belongs to STG 1, the default STG. To place the VLAN in a different STG, see “Manually Assigning STGs” on page 185. The VLAN is automatically removed from its old STG before being placed into the new STG.

Each VLANs must be contained within a single STG; a VLAN cannot span multiple STGs. By confining VLANs within a single STG, you avoid problems with Spanning Tree blocking ports and causing a loss of connectivity within the VLAN. When a VLAN spans multiple switches, it is recommended that the VLAN remain within the same STG (be assigned the same STG ID) across all the switches.

If ports are tagged, all aggregated ports can belong to multiple STGs.

A port cannot be directly added to an STG. The port must first be added to a VLAN, and that VLAN added to the desired STG.
Rules for VLAN Tagged/Trunk Mode Ports
The following rules apply to VLAN tagged ports:
186

Tagged/trunk mode ports can belong to more than one STG, but untagged/access mode ports can belong to only one STG.

When a tagged/trunk mode port belongs to more than one STG, the egress BPDUs are tagged to distinguish the BPDUs of one STG from those of another STG.
G8052 Application Guide for ENOS 8.4
Adding and Removing Ports from STGs
The following rules apply when you add ports to or remove ports from STGs:

When you add a port to a VLAN that belongs to an STG, the port is also added to that STG. However, if the port you are adding is an untagged port and is already a member of another STG, that port will be removed from its current STG and added to the new STG. An untagged port cannot belong to more than one STG.
For example: Assume that VLAN 1 belongs to STG 1, and that port 1 is untagged and does not belong to any STG. When you add port 1 to VLAN 1, port 1 will automatically become part of STG 1.
However, if port 5 is untagged and is a member of VLAN 3 in STG 2, then adding port 5 to VLAN 1 in STG 1 will change the port PVID from 3 to 1: "Port 5 is an UNTAGGED/Access Mode port and its PVID/Native­VLAN changed from 3 to 1.

When you remove a port from VLAN that belongs to an STG, that port will also be removed from the STG. However, if that port belongs to another VLAN in the same STG, the port remains in the STG.
As an example, assume that port 2 belongs to only VLAN 2, and that VLAN 2 belongs to STG 2. When you remove port 2 from VLAN 2, the port is moved to default VLAN 1 and is removed from STG 2.
However, if port 2 belongs to both VLAN 1 and VLAN 2, and both VLANs belong to STG 1, removing port 2 from VLAN 2 does not remove port 2 from STG 1 because the port is still a member of VLAN 1, which is still a member of STG 1.

An STG cannot be deleted, only disabled. If you disable the STG while it still contains VLAN members, Spanning Tree will be off on all ports belonging to that VLAN.
The relationship between port, LAGs, VLANs, and Spanning Trees is shown in Table 16 on page 179.
© Copyright Lenovo 2016
Chapter 11: Spanning Tree Protocols
187
The Switch-Centric Model
PVRST is switch‐centric: STGs are enforced only on the switch where they are configured. PVRST allows only one VLAN per STG, except for the default STG 1 to which multiple VLANs can be assigned. The STG ID is not transmitted in the Spanning Tree BPDU. Each Spanning Tree decision is based entirely on the configuration of the particular switch.
For example, in Figure 14, each switch is responsible for the proper configuration of its own ports, VLANs, and STGs. Switch A identifies its own port 17 as part of VLAN 2 on STG 2, and the Switch B identifies its own port 8 as part of VLAN 2 on STG 2.
Figure 14. Implementing PVRST
Chassis
Switch A
Application
Switch B
17
STG 2
8
VLAN 2
18
2
STG 3
VLAN 3
8
1
STG 1
VLAN 1
2
1
1
Application
Switch C
8
Application
Switch D
The VLAN participation for each Spanning Tree Group in Figure 14 on page 188 is as follows:

VLAN 1 Participation
Assuming Switch B to be the root bridge, Switch B transmits the BPDU for STG 1 on ports 1 and 2. Switch C receives the BPDU on port 2, and Switch D receives the BPDU on port 1. Because there is a network loop between the switches in VLAN 1, either Switch D will block port 8 or Switch C will block port 1, depending on the information provided in the BPDU.

VLAN 2 Participation
Switch B, the root bridge, generates a BPDU for STG 2 from port 8. Switch A receives this BPDU on port 17, which is assigned to VLAN 2, STG 2. Because switch B has no additional ports participating in STG 2, this BPDU is not forwarded to any additional ports and Switch B remains the designated root.

VLAN 3 Participation
For VLAN 3, Switch A or Switch C may be the root bridge. If Switch A is the root bridge for VLAN 3, STG 3, then Switch A transmits the BPDU from port 18. Switch C receives this BPDU on port 8 and is identified as participating in VLAN 3, STG 3. Since Switch C has no additional ports participating in STG 3, this BPDU is not forwarded to any additional ports and Switch A remains the designated root.
188
G8052 Application Guide for ENOS 8.4
Configuring Multiple STGs
This configuration shows how to configure the three instances of STGs on the switches A, B, C, and D illustrated in Figure 14 on page 188.
Because VASA is enabled by default, each new VLAN is automatically assigned its own STG. 1. Set the Spanning Tree mode on each switch to PVRST. RS G8052(config)# spanning­tree mode pvrst
Note: PVRST is the default mode on the G8052. This step is not required unless the STP mode has been previously changed, and is shown here merely as an example of manual configuration.
2. Configure the following on Switch A:
a. Enable VLAN 2 and VLAN 3. RS
RS
RS
RS
G8052(config)# vlan 2
G8052(config­vlan)# exit
G8052(config)# vlan 3
G8052(config­vlan)# exit
If VASA is disabled, enter the following commands:
RS G8052(config)# spanning­tree stp 2 vlan 2
RS G8052(config)# spanning­tree stp 3 vlan 3
b. Add port 17 to VLAN 2, port 18 to VLAN 3. RS
RS
RS
RS
G8052(config)# interface port 17
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 2
G8052(config­if)# exit
RS
RS
RS
RS
G8052(config)# interface port 18
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 3
G8052(config­if)# exit
VLAN 2 and VLAN 3 are removed from STG 1.
Note: In PVRST mode, each instance of STG is enabled by default.
© Copyright Lenovo 2016
Chapter 11: Spanning Tree Protocols
189
3. Configure the following on Switch B:
a. Add port 8 to VLAN 2. Ports 1 and 2 are by default in VLAN 1 assigned to STG 1. RS
RS
RS
RS
RS
RS
G8052(config)# vlan 2
G8052(config­vlan)# exit
G8052(config)# interface port 8
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 2
G8052(config­if)# exit
If VASA is disabled, enter the following command:
RS G8052(config)# spanning­tree stp 2 vlan 2
b. VLAN 2 is automatically removed from STG 1. By default VLAN 1 remains in STG 1.
4. Configure the following on application switch C:
a. Add port 8 to VLAN 3. Ports 1 and 2 are by default in VLAN 1 assigned to STG 1. RS
RS
RS
RS
RS
RS
G8052(config)# vlan 3
G8052(config­vlan)# exit
G8052(config)# interface port 8
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 3
G8052(config­if)# exit
If VASA is disabled, enter the following command:
RS G8052(config)# spanning­tree stp 3 vlan 3
b. VLAN 3 is automatically removed from STG 1. By default VLAN 1 remains in STG 1.
5. Switch D does not require any special configuration for multiple Spanning Trees. Switch D uses default STG 1 only.
190
G8052 Application Guide for ENOS 8.4
Rapid Spanning Tree Protocol
RSTP provides rapid convergence of the Spanning Tree and provides the fast re‐configuration critical for networks carrying delay‐sensitive traffic such as voice and video. RSTP significantly reduces the time to reconfigure the active topology of the network when changes occur to the physical topology or its configuration parameters. RSTP reduces the bridged‐LAN topology to a single Spanning Tree.
RSTP was originally defined in IEEE 802.1w (2001) and was later incorporated into IEEE 802.1D (2004), superseding the original STP standard.
RSTP parameters apply only to Spanning Tree Group (STG) 1. The PVRST mode STGs 2‐128 are not used when the switch is placed in RSTP mode.
RSTP is compatible with devices that run IEEE 802.1D (1998) Spanning Tree Protocol. If the switch detects IEEE 802.1D (1998) BPDUs, it responds with IEEE 802.1D (1998)‐compatible data units. RSTP is not compatible with Per‐VLAN Rapid Spanning Tree (PVRST) protocol. Port States
RSTP port state controls are the same as for PVRST: discarding, learning, and forwarding.
Due to the sequence involved in these STP states, considerable delays may occur while paths are being resolved. To mitigate delays, ports defined as edge/portfast ports (“Port Type and Link Type” on page 197) may bypass the discarding and learning states, and enter directly into the forwarding state.
RSTP Configuration Guidelines
This section provides important information about configuring RSTP. When RSTP is turned on, the following occurs:
© Copyright Lenovo 2016

STP parameters apply only to STG 1.

Only STG 1 is available. All other STGs are turned off.

All VLANs are moved to STG 1.
Chapter 11: Spanning Tree Protocols
191
RSTP Configuration Example
This section provides steps to configure RSTP.
1. Configure port and VLAN membership on the switch.
2. Set the Spanning Tree mode to Rapid Spanning Tree. RS G8052(config)# spanning­tree mode rstp
3. Configure RSTP parameters. RS
RS
RS
RS
RS
G8052(config)#
G8052(config)#
G8052(config)#
G8052(config)#
G8052(config)#
spanning-tree stp 1 bridge priority 8192
spanning-tree stp 1 bridge hello-time 5
spanning-tree stp 1 bridge forward-delay 20
spanning-tree stp 1 bridge maximum-age 30
no spanning-tree stp 1 enable
4. Configure port parameters: RS
RS
RS
RS
RS
192
G8052(config)# interface port 3
G8052(config-if)# spanning-tree stp 1 priority 240
G8052(config-if)# spanning-tree stp 1 path-cost 500
G8052(config-if)# no spanning-tree stp 1 enable
G8052(config-if)# exit
G8052 Application Guide for ENOS 8.4
Multiple Spanning Tree Protocol
Multiple Spanning Tree Protocol (MSTP) extends Rapid Spanning Tree Protocol (RSTP), allowing multiple Spanning Tree Groups (STGs) which may each include multiple VLANs. MSTP was originally defined in IEEE 802.1s (2002) and was later included in IEEE 802.1Q (2003).
In MSTP mode, the G8052 supports up to 32 instances of Spanning Tree, corresponding to STGs 1‐32, with each STG acting as an independent, simultaneous instance of RSTP.
MSTP allows frames assigned to different VLANs to follow separate paths, with each path based on an independent Spanning Tree instance. This approach provides multiple forwarding paths for data traffic, thereby enabling load‐balancing, and reducing the number of Spanning Tree instances required to support a large number of VLANs.
Due to Spanning Tree’s sequence of discarding, learning, and forwarding, lengthy delays may occur while paths are being resolved. Ports defined as edge/portfast ports (“Port Type and Link Type” on page 197) bypass the Discarding and Learning states, and enter directly into the Forwarding state.
MSTP Region
A group of interconnected bridges that share the same attributes is called an MST region. Each bridge within the region must share the following attributes:

Alphanumeric name

Revision number

VLAN‐to STG mapping scheme
MSTP provides rapid re‐configuration, scalability and control due to the support of regions, and multiple Spanning‐Tree instances support within each region.
Common Internal Spanning Tree
The Common Internal Spanning Tree (CIST) or MST0 provides a common form of Spanning Tree Protocol, with one Spanning‐Tree instance that can be used throughout the MSTP region. CIST allows the switch to interoperate with legacy equipment, including devices that run IEEE 802.1D (1998) STP.
CIST allows the MSTP region to act as a virtual bridge to other bridges outside of the region, and provides a single Spanning‐Tree instance to interact with them.
CIST port configuration includes Hello time, Edge/portfast port enable/disable, and Link Type. These parameters do not affect Spanning Tree Groups 1–32. They apply only when the CIST is used.
© Copyright Lenovo 2016
Chapter 11: Spanning Tree Protocols
193
MSTP Configuration Guidelines
This section provides important information about configuring Multiple Spanning Tree Groups:

When the switch initially has PVRST mode enabled and VLANs 1‐127 are configured and distributed to STGs 1‐127, when you turn on MSTP, the switch moves VLAN 1 and VLANs 33‐128 to the CIST. When MSTP is turned off, the switch moves VLAN 1 and VLANs 33‐127 from the CIST to STG 1. 
When you enable MSTP, a default revision number of 1 and a blank region name are automatically configured.
MSTP Configuration Examples
The following section contains examples of how to configure multiple spanning trees.
MSTP Example 1
This section provides steps to configure MSTP on the G8052.
1. Configure port and VLAN membership on the switch.
2. Configure Multiple Spanning Tree region parameters, and set the mode to MSTP. RS G8052(config)# spanning­tree mst configuration
(Enter MST configuration mode)
RS G8052(config­mst)# name <name>
(Define the Region name)
RS G8052(config­mst)# revision <0 – 65535>(Define the Region revision number)
RS G8052(config­mst)# exit
RS G8052(config)# spanning­tree mode mst(Set mode to Multiple Spanning Trees) 3. Map VLANs to MSTP instances: RS G8052(config)# spanning­tree mst configuration
(Enter MST configuration mode)
RS G8052(config­mst)# instance <instance ID> vlan <vlan number or range>
194
G8052 Application Guide for ENOS 8.4
MSTP Example 2
This configuration shows how to configure MSTP Groups on the switch, as shown in Figure 14. Figure 15. Implementing Multiple Spanning Tree Groups Enterprise
Routing Switch
Enterprise
Routing Switch
MSTP Group 1
Root
MSTP Group 2
Root
Passing VLAN 1
Blocking VLAN 2
Server 1
VLAN 1
Server 2
VLAN 1
Blocking VLAN 1
Passing VLAN 2
Server 3
VLAN 2
Server 4
VLAN 2
This example shows how multiple Spanning Trees can provide redundancy without wasting any uplink ports. In this example, the server ports are split between two separate VLANs. Both VLANs belong to two different MSTP groups. The Spanning Tree priority values are configured so that each routing switch is the root for a different MSTP instance. All of the uplinks are active, with each uplink port backing up the other.
1. Configure port membership and define the STGs for VLAN 1. Enable tagging on uplink ports that share VLANs. Port 19 and port 20 connect to the Enterprise Routing switches. RS G8052(config)# interface port 19, 20
RS G8052(config­if)# switchport mode trunk
RS G8052(config­if)# exit
2. Configure MSTP: Spanning Tree mode, region name, and version. RS G8052(config)# spanning­tree mst configuration
RS G8052(config­mst)# name MyRegion
(Define the Region name)
RS G8052(config­mst)# revision 100 (Define the Revision level)
RS G8052(config­mst)# exit
RS G8052(config)# spanning­tree mode mst(Set mode to Multiple Spanning Trees)
© Copyright Lenovo 2016
Chapter 11: Spanning Tree Protocols
195
3. Map VLANs to MSTP instances: RS G8052(config)# spanning­tree mst configuration
RS G8052(config­mst)# instance 1 vlan 1
RS G8052(config­mst)# instance 2 vlan 2
4. Configure port membership and define the STGs for VLAN 2. Add server ports 3 and 4 to VLAN 2. Uplink ports 19 and 20 are automatically added to VLAN 2. Assign VLAN 2 to STG 2. RS G8052(config)# interface port 3,4
RS G8052(config­if)# switchport access vlan 2
RS G8052(config­if)# exit
Note: Each STG is enabled by default.
196
G8052 Application Guide for ENOS 8.4
Port Type and Link Type
The following port types and link types work with STP.
Edge/Portfast Port
A port that does not connect to a bridge is called an edge port. Since edge ports are assumed to be connected to non‐STP devices (such as directly to hosts or servers), they are placed in the forwarding state as soon as the link is up. Edge ports send BPDUs to upstream STP devices like normal STP ports, but do not receive BPDUs. If a port with edge enabled does receive a BPDU, it immediately begins working as a normal (non‐edge) port, and participates fully in Spanning Tree.
Use the following commands to define or clear a port as an edge port: RS G8052(config)# interface port <port>
RS G8052(config­if)# [no] spanning­tree portfast
RS G8052(config­if)# exit
Link Type
The link type determines how the port behaves in regard to Rapid Spanning Tree. Use the following commands to define the link type for the port: RS G8052(config)# interface port <port>
RS G8052(config­if)# [no] spanning­tree link­type <type>
RS G8052(config­if)# exit
where type corresponds to the duplex mode of the port, as follows:

p2p
A full‐duplex link to another device (point‐to‐point)

shared
A half‐duplex link is a shared segment and can contain more than one device.

auto
The switch dynamically configures the link type.
Note: Any STP port in full‐duplex mode can be manually configured as a shared port when connected to a non‐STP‐aware shared device (such as a typical Layer 2 switch) used to interconnect multiple STP‐aware devices.
© Copyright Lenovo 2016
Chapter 11: Spanning Tree Protocols
197
198
G8052 Application Guide for ENOS 8.4
Chapter 12. Virtual Link Aggregation Groups
In many data center environments, downstream servers or switches connect to upstream devices which consolidate traffic. For example, see Figure 16.
Figure 16. Typical Data Center Switching Layers with STP vs. VLAG
ISL
Aggregation
Layer
STP blocks
implicit loops
VLAGs
VLAG
Peers
Links remain
active
Access
Layer
Servers
As shown in the example, a switch in the access layer may be connected to more than one switch in the aggregation layer to provide for network redundancy. Typically, Spanning Tree Protocol (RSTP, PVRST, or MSTP—see Chapter 11, “Spanning Tree Protocols) is used to prevent broadcast loops, blocking redundant uplink paths. This has the unwanted consequence of reducing the available bandwidth between the layers by as much as 50%. In addition, STP may be slow to resolve topology changes that occur during a link failure, and can result in considerable MAC address flooding.
Using Virtual Link Aggregation Groups (VLAGs), the redundant uplinks remain active, utilizing all available bandwidth.
Two switches are paired into VLAG peers, and act as a single virtual entity for the purpose of establishing a multi‐port aggregation. Ports from both peers can be grouped into a VLAG and connected to the same LAG‐capable target device. From the perspective of the target device, the ports connected to the VLAG peers appear to be a single LAG connecting to a single logical device. The target device uses the configured Tier ID to identify the VLAG peers as this single logical device. It is important that you use a unique Tier ID for each VLAG pair you configure. The VLAG‐capable switches synchronize their logical view of the access layer port structure and internally prevent implicit loops. The VLAG topology also responds more quickly to link failure and does not result in unnecessary MAC flooding.
VLAGs are also useful in multi‐layer environments for both uplink and downlink redundancy to any regular LAG‐capable device. For example:
© Copyright Lenovo 2016
199
Figure 17. VLAG Application with Multiple Layers
Layer 2/3 Border
LACP-capable
Routers
LAG
LAG
VLAG 5
VLAG 6
ISL
Layer 2 Region
with multiple levels
VLAG
Peers C
LAG
VLAG 3
VLAG 3
VLAG 4
ISL
VLAG
Peers A
ISL
VLAG
Peers B
VLAG 1
LAG
Servers
VLAG 2
LACP-capable
Switch
LAG
LACP-capable
Server
Wherever ports from both peered switches are aggregated to another device, the aggregated ports must be configured as a VLAG. For example, VLAGs 1 and 3 must be configured for both VLAG Peer A switches. VLAGs 2 and 4 must be configured for both VLAG Peer B switches.VLAGs 3, 5, and 6 must be configured on both VLAG Peer C switches. Other devices connecting to the VLAG peers are configured using regular static or dynamic LAGs.
Note: Do not configure a VLAG for connecting only one switch in the peer set to another device or peer set. For instance, in VLAG Peer C, a regular LAG is employed for the downlink connection to VLAG Peer B because only one of the VLAG Peer C switches is involved.
200
G8052 Application Guide for ENOS 8.4
In addition, when used with VRRP, VLAGs can provide seamless active‐active failover for network links. For example
Figure 18. VLAG Application with VRRP:
VLAG
Peers
ISL
VRRP
Master
Server
© Copyright Lenovo 2016
VLAG
VRRP
Backup
Active
Traffic Flows
Chapter 12: Virtual Link Aggregation Groups
201
VLAG Capacities
Servers or switches that connect to the VLAG peers using a multi‐port VLAG are considered VLAG clients. VLAG clients are not required to be VLAG‐capable. The ports participating in the VLAG are configured as regular port LAGs on the VLAG client end.
On the VLAG peers, the VLAGs are configured similarly to regular port LAGs, using many of the same features and rules. See Chapter 10, “Ports and Link Aggregation” for general information concerning all port LAGs.
Each VLAG begins as a regular port LAG on each VLAG‐peer switch. The VLAG may be either a static LAG (portchannel) or dynamic LACP LAG, and consumes one slot from the overall port LAG capacity pool. The LAG type must match that used on VLAG client devices. Additional configuration is then required to implement the VLAG on both VLAG peer switches. You may configure up to 52 LAGs on the switch, with all types (regular or VLAG, static or LACP) sharing the same pool.
The maximum number of supported VLAG instances is as follows:

With STP off: Maximum of 31 VLAG instances

With STP on:

PVRST/MSTP with one VLAG instance per VLAN/STG: Maximum of 31 VLAG instances

PVRST/MSTP with one VLAG instance belonging to multiple VLANs/STGs: Maximum of 15 VLAG instances
Each LAG type can contain up to 8 member ports, depending on the port type and availability.
VLAGs versus Port LAGs
Though similar to regular port LAGs in many regards, VLAGs differ from regular port LAGs in a number of important ways:

A VLAG can consist of multiple ports on two VLAG peers, which are connected to one logical client device such as a server, switch, or another VLAG device.

The participating ports on the client device are configured as a regular port LAG.

The VLAG peers must be the same model, and run the same software version.

VLAG peers require a dedicated inter‐switch link (ISL) for synchronization. The ports used to create the ISL must have the following properties:

202

ISL ports must have VLAN tagging turned on.

ISL ports must be configured for all VLAG VLANs.

ISL ports must be placed into a regular port LAG (dynamic or static).

A minimum of two ports on each switch are recommended for ISL use.
Dynamic routing protocols, such as OSPF, cannot terminate on VLAGs.
G8052 Application Guide for ENOS 8.4
© Copyright Lenovo 2016

Routing over VLAGs is not supported. However, IP forwarding between subnets served by VLAGs can be accomplished using VRRP.

VLAGs are configured using additional commands.

It is recommended that end‐devices connected to VLAG switches use NICs with dual‐homing. This increases traffic efficiency, reduces ISL load, and provides faster link failover.
Chapter 12: Virtual Link Aggregation Groups
203
Configuring VLAGs
When configuring VLAG or making changes to your VLAG configuration, consider the following VLAG behavior:

When adding a static Mrouter on VLAG links, ensure that you also add it on the ISL link to avoid VLAG link failure. If the VLAG link fails, traffic cannot be recovered through the ISL. Also ensure you add the same static entry on the peer VLAG switch for VLAG ports.

If you have enabled VLAG on the switch, and you need to change the STP mode, ensure that you first disable VLAG and then change the STP mode.

When VLAG is enabled, you may see two root ports on the secondary VLAG switch. One of these will be the actual root port for the secondary VLAG switch and the other will be a root port synced with the primary VLAG switch.

The LACP key used must be unique for each VLAG in the entire topology. 
The STG to VLAN mapping on both VLAG peers must be identical.
The following parameters must be identically configured on the VLAG ports of both the VLAG peers:
204

VLANs

Native VLAN tagging

Native VLAN/PVID

STP mode

BPDU Guard setting

STP port setting

MAC aging timers

Static MAC entries

ACL configuration parameters

QoS configuration parameters
G8052 Application Guide for ENOS 8.4
Basic VLAG Configuration
Figure 19 shows an example configuration where two VLAG peers are used for aggregating traffic from downstream devices.
Figure 19. Basic VLAGs
ISL
VLAG Peer 1
1
2
Mgmt IP: 10.10.10.1/24
8
9
VLAG Peer 2
2
3
LACP 200
VLAG 1
Mgmt IP: 10.10.10.2/24
7
8
VLAG 2
LACP 1000
VLAN 100
LACP 2000
VLAN 100
Client Switch
Client Switch
In this example, each client switch is connected to both VLAG peers. On each client switch, the ports connecting to the VLAG peers are configured as a dynamic LACP port LAG. The VLAG peer switches share a dedicated ISL for synchronizing VLAG information. On the individual VLAG peers, each port leading to a specific client switch (and part of the client switch’s port LAG) is configured as a VLAG.
In the following example configuration, only the configuration for VLAG 1 on VLAG Peer 1 is shown. VLAG Peer 2 and all other VLAGs are configured in a similar fashion.
Configuring the ISL
The ISL connecting the VLAG peers is shared by all their VLAGs. The ISL needs to be configured only once on each VLAG peer.
1. Configure STP if required. Use PVRST or MSTP mode only:
RS G8052(config)# spanning­tree mode pvrst
2. Configure the ISL ports and place them into a port LAG:
RS
RS
RS
RS
RS
RS
© Copyright Lenovo 2016
G8052(config)# interface port 1­2
G8052(config­if)# switchport mode trunk
G8052(config­if)# lacp mode active
G8052(config­if)# lacp key 200
G8052(config­if)# exit
G8052(config)# vlag isl adminkey 200
Chapter 12: Virtual Link Aggregation Groups
205
Notes:

In this case, a dynamic LAG is shown. A static LAG (portchannel) could be configured instead.

ISL ports and VLAG ports must be members of the same VLANs.
3. Configure VLAG Tier ID. This is used to identify the VLAG switch in a multi‐tier environment. RS G8052(config)# vlag tier­id 10
4. Configure the ISL for the VLAG peer.
Make sure you configure the VLAG peer (VLAG Peer 2) using the same ISL aggregation type (dynamic or static), the same VLAN for VLAG and VLAG ISL ports, and the same STP mode and tier ID used on VLAG Peer 1.
Configuring the VLAG
To configure the VLAG:
1. Configure the VLAN for VLAG 1 ports. Make sure members include the ISL and VLAG 1 ports. Once the VLAN is ready, the ISL ports are automatically added to it.
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 100
G8052(config­vlan)# exit
G8052(config)# interface port 8
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 100
G8052(config­if)# exit
Note: In MSTP mode, VLANs are automatically mapped to CIST.
2. Place the VLAG 1 port(s) in a port LAG:
RS
RS
RS
RS
G8052(config)# interface port 8
G8052(config­if)# lacp mode active
G8052(config­if)# lacp key 1000
G8052(config­if)# exit
3. Assign the LAG to the VLAG:
RS G8052(config)# vlag adminkey 1000 enable
4. Continue by configuring all required VLAGs on VLAG Peer 1, and then repeat the configuration for VLAG Peer 2.
For each corresponding VLAG on the peer, the port LAG type (dynamic or static), VLAN, STP mode, and ID must be the same as on VLAG Peer 1.
5. Enable VLAG globally.
RS G8052(config)# vlag enable
206
G8052 Application Guide for ENOS 8.4
6. Verify the completed configuration:
# show vlag information
© Copyright Lenovo 2016
Chapter 12: Virtual Link Aggregation Groups
207
VLAG Configuration - VLANs Mapped to MSTI
Follow the steps in this section to configure VLAG in environments where the STP mode is MSTP and no previous VLAG was configured.
Configuring the ISL
The ISL connecting the VLAG peers is shared by all their VLAGs. The ISL needs to be configured only once on each VLAG peer. Ensure you have the same region name, revision and VLAN‐to‐STG mapping on both VLAG switches.
1. Configure STP:
RS G8052(config)# spanning­tree mode mst
2. Configure the ISL ports and place them into a portchannel (dynamic or static):
RS
RS
RS
RS
RS
RS
G8052(config)# interface port 1­2
G8052(config­if)# switchport mode trunk
G8052(config­if)# lacp mode active
G8052(config­if)# lacp key 200
G8052(config­if)# exit
G8052(config)# vlag isl adminkey 200
Notes:

In this case, a dynamic LAG is shown. A static LAG (portchannel) could be configured instead.

ISL ports and VLAG ports must be members of the same VLANs.
3. Configure the VLAG Tier ID. This is used to identify the VLAG switch in a multi‐tier environment. RS G8052(config)# vlag tier­id 10
4. Configure the ISL for the VLAG peer.
Make sure you configure the VLAG peer (VLAG Peer 2) using the same ISL aggregation type (dynamic or static), the same VLAN for VLAG and VLAG ISL ports, and the same STP mode and tier ID used on VLAG Peer 1.
208
G8052 Application Guide for ENOS 8.4
Configuring the VLAG
To configure the VLAG:
1. Configure the VLAN for VLAG 1 ports. RS G8052(config)# vlan 100
RS G8052(config­vlan)# exit
Note: The VLAN is automatically mapped to CIST.
2. Shut down ISL ports and VLAG ports. This ensures that traffic passes through to other switches. RS G8052(config)# interface port 1­2,8
RS G8052(config­if)# shutdown
3. Map the VLAN to an MSTI. RS G8052(config)# spanning­tree mst 1 vlan 100
4. Disable VLAG. RS G8052(config)# no vlag enable
5. Add VLAG ports to the VLAN. RS
RS
RS
RS
G8052(config)# interface port 1­2,8
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 100
G8052(config­if)# exit
6. Enable VLAG. RS G8052(config)# vlag enable
7. Place the VLAG 1 ports in a port trunk group.
RS
RS
RS
RS
G8052(config)# interface port 8
G8052(config­if)# lacp mode active
G8052(config­if)# lacp key 1000
G8052(config­if)# exit
8. Assign the trunk to the VLAG.
RS G8052(config)# vlag adminkey 1000 enable
9. Continue by configuring all required VLAGs on VLAG Peer 1, then follow the steps for configuring VLAG Peer 2.
© Copyright Lenovo 2016
Chapter 12: Virtual Link Aggregation Groups
209
10. Configure the VLAN for VLAG 2. RS G8052(config)# vlan 100
RS G8052(config­vlan)# exit
Note: The VLAN is automatically mapped to CIST.
11. Map the VLAN to an MSTI. RS G8052(config)# spanning­tree mst 1 vlan 100
Note: At this point, traffic may be momentarily disrupted due to STP recalculation.
12. Disable VLAG. RS G8052(config)# no vlag enable
Note: At this point, traffic may be momentarily disrupted due to STP recalculation.
13. Add VLAG ports to the VLAN. RS
RS
RS
RS
G8052(config)# interface port 1­2,8
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 100
G8052(config­if)# exit
14. Enable VLAG. RS G8052(config)# vlag enable
Note: At this point, traffic may be momentarily disrupted due to STP recalculation.
On VLAG Peer 1:
15. Enable ISL ports and VLAG ports: RS G8052(config)# interface port 1­2,8
RS G8052(config­if)# no shutdown
On VLAG Peer2:
16. Place the VLAG 2 ports in a port trunk group:
RS
RS
RS
RS
G8052(config)# interface port 8
G8052(config­if)# lacp mode active
G8052(config­if)# lacp key 1000
G8052(config­if)# exit
17. Assign the trunk to the VLAG:
RS G8052(config)# vlag adminkey 1000 enable
210
G8052 Application Guide for ENOS 8.4
18. Verify the completed configuration:
RS G8052# show vlag
© Copyright Lenovo 2016
Chapter 12: Virtual Link Aggregation Groups
211
VLAGs with VRRP
Note: In a multi‐layer environment, configure VRRP separately for each layer. We recommend that you configure VRRP only on the tier with uplinks. See “Configuring VLAGs in Multiple Layers” on page 220.
VRRP (see Chapter 34, “Virtual Router Redundancy Protocol”) can be used in conjunction with VLAGs and LACP‐capable devices to provide seamless redundancy.
Figure 20. Active‐Active Configuration using VRRP and VLAGs
VRRP Master
Server 1
VLAG Peer 1
Layer 3
Router
VLAG 1
VIR: 10.0.1.100
1
10.0.1.1
10
11
2
Internet
4
5
4
5
VLAG 2
12
Server 2
ISL
10.0.1.2
10
1
11
12
VLAG 3
Server 3
2
Layer 3
Router
VRRP Backup
10.0.1.3
VLAG Peer 2
VIR: 10.0.1.100
Network 10.0.1.0/24
Task 1: Configure VLAG Peer 1
Note: Before enabling VLAG, you must configure the VLAG tier ID and ISL portchannel.
1. Configure VLAG tier ID RS G8052(config)# vlag tier­id 10
2. Configure appropriate routing.
RS
RS
RS
RS
G8052(config)# router ospf
G8052(config­router­ospf)# area 1 area­id 0.0.0.1
G8052(config­router­ospf)# enable
G8052(config­router­ospf)# exit
Although OSPF is used in this example, static routing could also be deployed. For more information, see Chapter 30, “Open Shortest Path First” or Chapter 21, “Basic IP Routing.”
3. Configure a server‐facing interface.
RS
RS
RS
RS
212
G8052(config)# interface ip 3
G8052(config­ip­if)# ip address 10.0.1.10 255.255.255.0
G8052(config­ip­if)# vlan 100
G8052(config­ip­if)# exit
G8052 Application Guide for ENOS 8.4
4. Turn on VRRP and configure the Virtual Interface Router.
RS
RS
RS
RS
RS
RS
G8052(config)# router vrrp
G8052(config­vrrp)# enable
G8052(config­vrrp)# virtual­router 1 virtual­router­id 1
G8052(config­vrrp)# virtual­router 1 interface 3
G8052(config­vrrp)# virtual­router 1 address 10.0.1.100
G8052(config­vrrp)# virtual­router 1 enable
5. Set the priority of Virtual Router 1 to 101, so that it becomes the Master.
RS G8052(config­vrrp)# virtual­router 1 priority 101
RS G8052(config­vrrp)# exit
6. Configure the ISL ports and place them into a port LAG:
RS
RS
RS
RS
RS
G8052(config)# interface port 4­5
G8052(config­if)# switchport mode trunk
G8052(config­if)# lacp mode active
G8052(config­if)# lacp key 2000
G8052(config­if)# exit
Note: In this case, a dynamic LAG is shown. A static LAG (portchannel) could be configured instead.
7. Configure the upstream ports.
RS
RS
RS
RS
RS
RS
G8052(config)# interface port 1
G8052(config­if)# switchport access vlan 10
G8052(config­if)# exit
G8052(config)# interface port 2
G8052(config­if)# switchport access vlan 20
G8052(config­if)# exit
8. Configure the server ports.
RS
RS
RS
RS
RS
RS
RS
RS
RS
© Copyright Lenovo 2016
G8052(config)# interface port 10
G8052(config­if)# switchport access vlan 100
G8052(config­if)# exit
G8052(config)# interface port 11
G8052(config­if)# switchport access vlan 100
G8052(config­if)# exit
G8052(config)# interface port 12
G8052(config­if)# switchport access vlan 100
G8052(config­if)# exit
Chapter 12: Virtual Link Aggregation Groups
213
9. Configure all VLANs including VLANs for the VLAGs. RS
RS
RS
RS
RS
RS
G8052(config)# vlan 10
G8052(config­vlan)# exit
G8052(config)# interface port 1
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan add 10
G8052(config­if)# exit
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 20
G8052(config­vlan)# exit
G8052(config)# interface port 2
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan add 20
G8052(config­if)# exit
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 100
G8052(config­vlan)# exit
G8052(config)# interface port 4­5
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 100
G8052(config­if)# exit
10. Configure Internet‐facing interfaces.
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip address 172.1.1.10 255.255.255.0
G8052(config­ip­if)# vlan 10
G8052(config­ip­if)# enable
G8052(config­ip­if)# ip ospf area 1
G8052(config­ip­if)# ip ospf enable
G8052(config­ip­if)# exit
G8052(config)# interface ip 2
G8052(config­ip­if)# ip address 172.1.3.10 255.255.255.0
G8052(config­ip­if)# vlan 20
G8052(config­ip­if)# enable
G8052(config­ip­if)# ip ospf area 1
G8052(config­ip­if)# ip ospf enable
G8052(config­ip­if)# exit
11. Place the VLAG port(s) in their port LAGs.
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface port 10
G8052(config­if)# lacp mode active
G8052(config­if)# lacp key 1000
G8052(config­if)# exit
G8052(config)# interface port 11
G8052(config­if)# lacp mode active
G8052(config­if)# lacp key 1100
G8052(config­if)# exit
G8052(config)# interface port 12
G8052(config­if)# lacp mode active
G8052(config­if)# lacp key 1200
G8052(config­if)# exit
12. Assign the LAGs to the VLAGs:
RS G8052(config)# vlag adminkey 1000 enable
RS G8052(config)# vlag adminkey 1100 enable
RS G8052(config)# vlag adminkey 1200 enable
214
G8052 Application Guide for ENOS 8.4
13. Globally enable VLAG
RS G8052(config)# vlag enable
14. Verify the completed configuration:
# show vlag information
Task 2: Configure VLAG Peer 2
The VLAG peer (VLAG Peer 2) must be configured using the same ISL aggregation type (dynamic or static), the same VLAN for VLAG and VLAG ISL ports, and the same STP mode and Tier ID used on VLAG Switch 1.
For each corresponding VLAG on the peer, the port LAG type (dynamic or static), VLAN, and STP mode and ID must be the same as on VLAG Switch 1.
1. Configure VLAG tier ID and enable VLAG globally. RS G8052(config)# vlag tier­id 10
RS G8052(config)# vlag enable
2. Configure appropriate routing.
RS
RS
RS
RS
G8052(config)# router ospf
G8052(config­router­ospf)# area 1 area­id 0.0.0.1
G8052(config­router­ospf)# enable
G8052(config­router­ospf)# exit
Although OSPF is used in this example, static routing could also be deployed.
3. Configure a server‐facing interface.
RS
RS
RS
RS
G8052(config)# interface ip 3
G8052(config­ip­if)# ip address 10.0.1.11 255.255.255.0
G8052(config­ip­if)# vlan 100
G8052(config­ip­if)# exit
4. Turn on VRRP and configure the Virtual Interface Router.
RS
RS
RS
RS
RS
RS
G8052(config)# router vrrp
G8052(config­vrrp)# enable
G8052(config­vrrp)# virtual­router 1 virtual­router­id 1
G8052(config­vrrp)# virtual­router 1 interface 3
G8052(config­vrrp)# virtual­router 1 address 10.0.1.100
G8052(config­vrrp)# virtual­router 1 enable
5. Configure the ISL ports and place them into a port LAG:
RS
RS
RS
RS
RS
© Copyright Lenovo 2016
G8052(config)# interface port 4­5
G8052(config­if)# switchport mode trunk
G8052(config­if)# lacp mode active
G8052(config­if)# lacp key 2000
G8052(config­if)# exit
Chapter 12: Virtual Link Aggregation Groups
215
6. Configure the upstream ports.
RS
RS
RS
RS
RS
RS
G8052(config)# interface port 1
G8052(config­if)# switchport access vlan 30
G8052(config­if)# exit
G8052(config)# interface port 2
G8052(config­if)# switchport access vlan 40
G8052(config­if)# exit
7. Configure the server ports.
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface port 10
G8052(config­if)# switchport access vlan 100
G8052(config­if)# exit
G8052(config)# interface port 11
G8052(config­if)# switchport access vlan 100
G8052(config­if)# exit
G8052(config)# interface port 12
G8052(config­if)# switchport access vlan 100
G8052(config­if)# exit
8. Configure all VLANs including VLANs for the VLAGs. 216
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 30
G8052(config­vlan)# exit
G8052(config)# interface port 1
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan add 30
G8052(config­if)# exit
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 40
G8052(config­vlan)# exit
G8052(config)# interface port 2
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan add 40
G8052(config­if)# exit
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 100
G8052(config­vlan)# exit
G8052(config)# interface port 4­5
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 100
G8052(config­if)# exit
G8052 Application Guide for ENOS 8.4
9. Configure Internet‐facing interfaces.
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip address 172.1.2.11 255.255.255.0
G8052(config­ip­if)# vlan 30
G8052(config­ip­if)# enable
G8052(config­ip­if)# ip ospf area 1
G8052(config­ip­if)# ip ospf enable
G8052(config­ip­if)# exit
G8052(config)# interface ip 2
G8052(config­ip­if)# ip address 172.1.4.12 255.255.255.0
G8052(config­ip­if)# vlan 40
G8052(config­ip­if)# enable
G8052(config­ip­if)# ip ospf area 1
G8052(config­ip­if)# ip ospf enable
G8052(config­ip­if)# exit
10. Place the VLAG port(s) in their port LAGs.
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface port 10
G8052(config­if)# lacp mode active
G8052(config­if)# lacp key 1000
G8052(config­if)# exit
G8052(config)# interface port 11
G8052(config­if)# lacp mode active
G8052(config­if)# lacp key 1100
G8052(config­if)# exit
G8052(config)# interface port 12
G8052(config­if)# lacp mode active
G8052(config­if)# lacp key 1200
G8052(config­if)# exit
11. Assign the LAGs to the VLAGs:
RS G8052(config)# vlag adminkey 1000 enable
RS G8052(config)# vlag adminkey 1100 enable
RS G8052(config)# vlag adminkey 1200 enable
12. Verify the completed configuration:
# show vlag information
© Copyright Lenovo 2016
Chapter 12: Virtual Link Aggregation Groups
217
Two-tier vLAGs with VRRP
vLAG Active‐Active VRRP makes the secondary vLAG switch route Layer 3 traffic, thus reducing routing latency. If it is used in a two‐tier vLAG environment, there may be two VRRP master switches for one VRRP domain and their role will constantly flap. To prevent such occurrences, there are two vLAG VRRP modes:
1. vLAG VRRP Active (Full Active‐Active) mode
In active mode, Layer 3 traffic is forwarded in all vLAG related VRRP domains. To enable vLAG VRRP active mode on a switch, use the following command: RS G8052(config)# vlag vrrp active
Note: This is the default vLAG VRRP mode.
2. vLAG VRRP Passive (Half Active‐Active) mode
In passive mode, Layer 3 traffic is forwarded in a vLAG related VRRP domain only if either the switch or its peer virtual router is the VRRP master. To enable vLAG VRRP passive mode on a switch, use the following command: RS G8052(config)# no vlag vrrp active
To verify the currently configured vLAG VRRP mode you can use the following command: RS G8052(config)# show vlag vrrp
218
G8052 Application Guide for ENOS 8.4
vLAG Peer Gateway
vLAG Peer Gateway allows a vLAG switch to act as the active gateway for packets that are addressed to the router MAC address of the vLAG peer. The feature enables local forwarding of such packets without crossing the ISL trunk, therefore improving ISL usage and avoiding potential traffic loss.
To make it functional, vLAG Peer Gateway must be configured on both vLAG peer switches.
By default, the feature is disabled. To enable it, use the following command: RS G8052(config)# vlag peer­gateway
Use the no form of the command to disable vLAG Peer Gateway.
To display information about the current vLAG Peer Gateway settings, use the following commands: RS G8052(config)# show vlag
RS G8052(config)# show vlag peer­gateway
© Copyright Lenovo 2016
Chapter 12: Virtual Link Aggregation Groups
219
FDB Refresh
vLAG uses a FDB refresh interval to periodically check the status of synchronized FDB entries. If a MAC address is detected as waiting to be removed from the FDB, the address will be re‐installed in the FDB.
By default, FDB refresh is enabled. To enable or disable FDB refresh, use the following command: RS G8052(config)# [no] vlag mac­address­table refresh
Configuring VLAGs in Multiple Layers
Figure 21. VLAG in Multiple Layers
Layer 2/3 Border
LACP-capable
Routers
LAG
LAG
VLAG 5
VLAG 6
ISL
Layer 2 Region
with multiple levels
Switch A
VLAG
Peers A
Switch B
VLAG
Peers C
VLAG 3
LAG
VLAG 3
VLAG 4
ISL
ISL
Switch C
Switch D
VLAG 1
Switch E
Switch F
VLAG
Peers B
VLAG 2
LAG
Switch G
LACP-capable
Switch
LAG
Servers
LACP-capable
Server
Figure 21 shows an example of VLAG being used in a multi‐layer environment. Following are the configuration steps for the topology. Task 1: Configure Layer 2/3 border switches.
Configure ports on border switch as follows: RS
RS
RS
RS
G8052(config)# interface port 1,2
G8052(config­if)# lacp key 100
G8052(config­if)# lacp mode active
G8052(config­if)# exit
Repeat the previous steps for the second border switch.
220
G8052 Application Guide for ENOS 8.4
Task 2: Configure switches in the Layer 2 region.
Consider the following:

ISL ports on switches A and B ‐ ports 1, 2

Ports connecting to Layer 2/3 ‐ ports 5, 6

Ports on switches A and B connecting to switches C and D: ports 10, 11

Ports on switch B connecting to switch E: ports 15, 16

Ports on switch B connecting to switch F: ports 17, 18
1. Configure VLAG tier ID and enable VLAG globally. RS G8052(config)# vlag tier­id 10
RS G8052(config)# vlag enable
2. Configure ISL ports on Switch A. RS
RS
RS
RS
RS
G8052(config)# interface port 1,2
G8052(config­if)# switchport mode trunk
G8052(config­if)# lacp key 200
G8052(config­if)# lacp mode active
G8052(config­if)# exit
RS G8052(config)# vlag isl adminkey 200
RS G8052(config­vlan)# exit
3. Configure port on Switch A connecting to Layer 2/3 router 1. RS G8052(config)# vlan 10
VLAN number 10 with name “VLAN 10” created
VLAN 10 was assigned to STG 10
RS G8052(config­vlan)# exit
RS G8052(config)# interface port 1,2,5
RS G8052(config­if)# switchport mode trunk
RS G8052(config­if)# switchport trunk allowed vlan 10
RS G8052(config­if)# exit
RS
RS
RS
RS
G8052(config)# interface port 5
G8052(config­if)# lacp key 400
G8052(config­if)# lacp mode active
G8052(config­if)# exit
RS G8052(config)# vlag adminkey 400 enable
Repeat the previous steps on Switch B for ports connecting to Layer 2/3 router 1.
© Copyright Lenovo 2016
Chapter 12: Virtual Link Aggregation Groups
221
4. Configure port on Switch A connecting to Layer 2/3 router 2. RS G8052(config)# vlan 20
VLAN number 20 with name “VLAN 20” created
VLAN 20 was assigned to STG 20
RS G8052(config­vlan)# exit
RS G8052(config)# interface port 1,2,6
RS G8052(config­if)# switchport mode trunk
RS G8052(config­if)# switchport trunk allowed vlan 20
RS G8052(config­if)# exit
RS
RS
RS
RS
G8052(config)# interface port 6
G8052(config­if)# lacp key 500
G8052(config­if)# lacp mode active
G8052(config­if)# exit
RS G8052(config)# vlag adminkey 500 enable
Repeat these commands on Switch B for ports connecting to Layer 2/3 router 2.
5. Configure ports on Switch A connecting to downstream VLAG switches C and D. RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 20
G8052(config­vlan)# exit
G8052(config)# interface port 10,11
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 20
G8052(config­if)# lacp key 600
G8052(config­if)# lacp mode active
G8052(config­if)# exit
RS G8052(config)# vlag adminkey 600 enable
Repeat these commands on Switch B for ports connecting to downstream VLAG switch C and D.
6. Configure ports on Switch B connecting to downstream switches E and F. RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 30
G8052(config­vlan)# exit
G8052(config)# interface port 15­18
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 30
G8052(config­if)# lacp key 700
G8052(config­if)# lacp mode active
G8052(config­if)# exit
7. Configure ISL between switches C and D, and between E and F as shown in Step 1.
8. Configure the Switch G as shown in Step 2.
VLAG with IGMPv3
Consider the following when using VLAG with IGMPv3:
222
G8052 Application Guide for ENOS 8.4

To maintain synchronization of the groups and sources states on the VLAG peers, traffic received on vLAG trunks is processed by the primary and then forwarded to the secondary. The secondary forwards the packets to the peer when it receives traffic on a vLAG and processes them when received from the peer. 
Traffic received on non‐vLAG ports but on an ISL VLAN is first processed by the receiving vLAG switch and then forwarded to the peer, which will synchronize them on the ISL trunk.

The querier enabled option is supported. After querier election, when one of the peers is elected as querier, it will generate queries when required.

When the secondary comes up after a reboot or ISL and health‐check fail, the information on the primary will be considered valid and synchronized with the secondary.

PIM and IGMPv3 are not supported to work together on VLAG.

When configuring VLAG with IGMPv3, the same version of IGMP needs to be set on both VLAG switches.

The number of IGMPv3 groups with VLAG depends on the number of included and excluded sources.

The total number of supported groups is the same as the number of groups the switch can learn with VLAG disabled. All other scenarios will have a behavior similar to IGMPv2 on VLAG.
© Copyright Lenovo 2016
Chapter 12: Virtual Link Aggregation Groups
223
224
G8052 Application Guide for ENOS 8.4
Chapter 13. Quality of Service
Quality of Service features allow you to allocate network resources to mission‐critical applications at the expense of applications that are less sensitive to such factors as time delays or network congestion. You can configure your network to prioritize specific types of traffic, ensuring that each type receives the appropriate Quality of Service (QoS) level.
The following topics are discussed in this section: © Copyright Lenovo 2016

“QoS Overview” on page 226

“Using ACL Filters” on page 227

“Using DSCP Values to Provide QoS” on page 229

“Using 802.1p Priority to Provide QoS” on page 235

“Queuing and Scheduling” on page 236

“Control Plane Protection” on page 236

“WRED with ECN” on page 237
225
QoS Overview
QoS helps you allocate guaranteed bandwidth to the critical applications, and limit bandwidth for less critical applications. Applications such as video and voice must have a certain amount of bandwidth to work correctly; using QoS, you can provide that bandwidth when necessary. Also, you can put a high priority on applications that are sensitive to timing out or that cannot tolerate delay, by assigning their traffic to a high‐priority queue. By assigning QoS levels to traffic flows on your network, you can ensure that network resources are allocated where they are needed most. QoS features allow you to prioritize network traffic, thereby providing better service for selected applications.
Figure 22 shows the basic QoS model used by the switch. Figure 22. QoS Model Ingress
Ports
Classify
Packets
Perform
Actions
ACL
Filter
Permit/Deny
Queue and
Schedule
COS
Queue
The basic QoS model works as follows: 


226
Classify traffic: 
Read DSCP value. 
Read 802.1p priority value. 
Match ACL filter parameters. Perform actions:

Define bandwidth and burst parameters

Select actions to perform on in‐profile and out‐of‐profile traffic

Deny packets

Permit packets

Mark DSCP or 802.1p Priority

Set COS queue (with or without re‐marking)
Queue and schedule traffic: 
Place packets in one of the COS queues. 
Schedule transmission based on the COS queue. G8052 Application Guide for ENOS 8.4
Egress
Using ACL Filters
Access Control Lists (ACLs) are filters that allow you to classify and segment traffic, so you can provide different levels of service to different traffic types. Each filter defines the conditions that must match for inclusion in the filter, and also the actions that are performed when a match is made.
Lenovo Enterprise Network Operating System 8.4 supports up to 640 ACLs.
The G8052 allows you to classify packets based on various parameters. For example:
Ethernet: source MAC, destination MAC, VLAN number/mask, Ethernet type, priority.
 IPv4: Source IP address/mask, destination address/mask, type of service, IP pro‐
tocol number.
 TCP/UPD: Source port, destination port, TCP flag.
 Packet format

For ACL details, see Chapter 7, “Access Control Lists.”
Summary of ACL Actions
Actions determine how the traffic is treated. The G8052 QoS actions include the following:

Pass or Drop

Redirect
Re‐mark a new DiffServ Code Point (DSCP)
 Re‐mark the 802.1p field
 Set the COS queue

© Copyright Lenovo 2016
Chapter 13: Quality of Service
227
ACL Metering and Re-Marking
You can define a profile for the aggregate traffic flowing through the G8052 by configuring a QoS meter (if desired) and assigning ACLs to ports. When you add ACLs to a port, make sure they are ordered correctly in terms of precedence.
Actions taken by an ACL are called In‐Profile actions. You can configure additional In‐Profile and Out‐of‐Profile actions on a port. Data traffic can be metered, and re‐marked to ensure that the traffic flow provides certain levels of service in terms of bandwidth for different types of network traffic.
Metering
QoS metering provides different levels of service to data streams through user‐configurable parameters. A meter is used to measure the traffic stream against a traffic profile, which you create. Thus, creating meters yields In‐Profile and Out‐of‐Profile traffic for each ACL, as follows:

In‐Profile–If there is no meter configured or if the packet conforms to the meter, the packet is classified as In‐Profile.

Out‐of‐Profile–If a meter is configured and the packet does not conform to the meter (exceeds the committed rate or maximum burst rate of the meter), the packet is classified as Out‐of‐Profile.
Using meters, you set a Committed Rate in Kbps (multiples of 64 Mbps). All traffic within this Committed Rate is In‐Profile. Additionally, you set a Maximum Burst Size that specifies an allowed data burst larger than the Committed Rate for a brief period. These parameters define the In‐Profile traffic.
Meters keep the sorted packets within certain parameters. You can configure a meter on an ACL, and perform actions on metered traffic, such as packet re‐marking.
Re-Marking
Re‐marking allows for the treatment of packets to be reset based on new network specifications or desired levels of service. You can configure the ACL to re‐mark a packet as follows:
228

Change the DSCP value of a packet, used to specify the service level traffic receives.

Change the 802.1p priority of a packet.
G8052 Application Guide for ENOS 8.4
Using DSCP Values to Provide QoS
The switch uses the Differentiated Services (DiffServ) architecture to provide QoS functions. DiffServ is described in IETF RFCs 2474 and 2475. The six most significant bits in the TOS byte of the IP header are defined as DiffServ Code Points (DSCP). Packets are marked with a certain value depending on the type of treatment the packet must receive in the network device. DSCP is a measure of the Quality of Service (QoS) level of the packet.
The switch can classify traffic by reading the DiffServ Code Point (DSCP) or IEEE 802.1p priority value, or by using filters to match specific criteria. When network traffic attributes match those specified in a traffic pattern, the policy instructs the switch to perform specified actions on each packet that passes through it. The packets are assigned to different Class of Service (COS) queues and scheduled for transmission. Differentiated Services Concepts
To differentiate between traffic flows, packets can be classified by their DSCP value. The Differentiated Services (DS) field in the IP header is an octet, and the first six bits, called the DS Code Point (DSCP), can provide QoS functions. Each packet carries its own QoS state in the DSCP. There are 64 possible DSCP values (0‐63). Figure 23. Layer 3 IPv4 packet Version
Length
ID
Length
ToS
Offset
TTL
Differentiated Services Code Point (DSCP)
unused
7
1
6
5
4
3
2
FCS
Proto
SIP
DIP
Data
0
The switch can perform the following actions to the DSCP: Read the DSCP value of ingress packets.  Re‐mark the DSCP value to a new value
 Map the DSCP value to a Class of Service queue (COSq). 
The switch can use the DSCP value to direct traffic prioritization. With DiffServ, you can establish policies to direct traffic. A policy is a traffic‐controlling mechanism that monitors the characteristics of the traffic, (for example, its source, destination, and protocol) and performs a controlling action on the traffic when certain characteristics are matched. © Copyright Lenovo 2016
Chapter 13: Quality of Service
229
Trusted/Untrusted Ports
By default, all ports on the G8052 are trusted. To configure untrusted ports, re‐mark the DSCP value of the incoming packet to a lower DSCP value using the following commands:
RS
RS
RS
RS
RS
230
G8052(config)# interface port 1
G8052(config­if)# dscp­marking
G8052(config­if)# exit
G8052(config)# qos dscp dscp­mapping <DSCP value (0‐63)> <new value>
G8052(config)# qos dscp re­marking
G8052 Application Guide for ENOS 8.4
Per Hop Behavior
The DSCP value determines the Per Hop Behavior (PHB) of each packet. The PHB is the forwarding treatment given to packets at each hop. QoS policies are built by applying a set of rules to packets, based on the DSCP value, as they hop through the network. The default settings are based on the following standard PHBs, as defined in the IEEE standards: 
Expedited Forwarding (EF)—This PHB has the highest egress priority and lowest drop precedence level. EF traffic is forwarded ahead of all other traffic. EF PHB is described in RFC 2598. 
Assured Forwarding (AF)—This PHB contains four service levels, each with a different drop precedence, as shown in the following table. Routers use drop precedence to determine which packets to discard last when the network becomes congested. AF PHB is described in RFC 2597. Drop
Precedence
Class 1
Class 3
Class 4
Low
AF11 (DSCP 10)
AF21 (DSCP 18)
AF31 (DSCP 26)
AF41 (DSCP 34)
Medium
AF12 (DSCP 12)
AF22 (DSCP 20)
AF32 (DSCP 28)
AF42 (DSCP 36)
High
AF13 (DSCP 14)
AF23 (DSCP 22)
AF33 (DSCP 30)
AF43 (DSCP 38)

Class Selector (CS)—This PHB has eight priority classes, with CS7 representing the highest priority, and CS0 representing the lowest priority, as shown in the following table. CS PHB is described in RFC 2474. Priority
Class Selector
DSCP
Highest
CS7
56
CS6
48
CS5
40
CS4
32
CS3
24
CS2
16
CS1
8
CS0
0
Lowest
© Copyright Lenovo 2016
Class 2
Chapter 13: Quality of Service
231
QoS Levels
Table 17 shows the default service levels provided by the switch, listed from highest to lowest importance: Table 17. Default QoS Service Levels
Service Level
Default PHB
802.1p Priority
Critical
CS7
7
Network Control
CS6
6
Premium
EF, CS5
5
Platinum
AF41, AF42, AF43, CS4
4
Gold
AF31, AF32, AF33, CS3
3
Silver
AF21, AF22, AF23, CS2
2
Bronze
AF11, AF12, AF13, CS1
1
Standard
DF, CS0
0
DSCP Re-Marking and Mapping
The switch can use the DSCP value of ingress packets to re‐mark the DSCP to a new value, and to set an 802.1p priority value. Use the following command to view the default settings. RS G8052# show qos dscp
Current DSCP Remarking Configuration: OFF
DSCP New DSCP New 802.1p Prio
­­­­­­­­ ­­­­­­­­ ­­­­­­­­­­­­­­­
0 0 0
1 1 0
2 2 0
3 3 0
4 4 0
5 5 0
6 6 0
7 7 0
8 8 1
9 9 0
10 10 1
...
54 54 0
55 55 0
56 56 7
57 57 0
58 58 0
59 59 0
60 60 0
61 61 0
62 62 0
63 63 0
232
G8052 Application Guide for ENOS 8.4
Use the following command to turn on DSCP re‐marking globally: RS G8052(config)# qos dscp re­marking
Then you must enable DSCP re‐marking on any port that you wish to perform this function (Interface Port mode). Note: If an ACL meter is configured for DSCP re‐marking, the meter function takes precedence over QoS re‐marking.
DSCP Re-Marking Configuration Examples
DSCP Re-Marking Configuration Example 1
The following example includes the basic steps for re‐marking DSCP value and mapping DSCP value to 802.1p.
1. Turn DSCP re‐marking on globally, and define the DSCP‐DSCP‐802.1p mapping. You can use the default mapping. RS G8052(config)# qos dscp re­marking
RS G8052(config)# qos dscp dscp­mapping <DSCP value (0‐63)> <new value>
RS G8052(config)# qos dscp dot1p­mapping <DSCP value (0‐63)> <802.1p value>
2. Enable DSCP re‐marking on a port.
RS G8052(config)# interface port 1
RS G8052(config­if)# qos dscp re­marking
RS G8052(config­if)# exit
DSCP Re-Marking Configuration Example 2
The following example assigns strict priority to VoIP traffic and a lower priority to all other traffic.
1. Create an ACL to re‐mark DSCP value and COS queue for all VoIP packets. RS
RS
RS
RS
RS
RS
G8052(config)# access­control list 2 tcp­udp source­port 5060 0xffff
G8052(config)# access­control list 2 meter committed­rate 10000000
G8052(config)# access­control list 2 meter enable
G8052(config)# access­control list 2 re­mark in­profile dscp 56
G8052(config)# access­control list 2 re­mark dot1p 7
G8052(config)# access­control list 2 action permit
2. Create an ACL to set a low priority to all other traffic.
RS G8052(config)# access­control list 3 action set­priority 1
RS G8052(config)# access­control list 3 action permit
3. Apply the ACLs to a port and enable DSCP marking.
RS G8052(config)# interface port 5
RS G8052(config­if)# access­control list 2
RS G8052(config­if)# access­control list 3 ethernet source­mac­address 00:00:00:00:00:00 00:00:00:00:00:00
RS G8052(config­if)# dscp­marking
RS G8052(config­if)# exit
© Copyright Lenovo 2016
Chapter 13: Quality of Service
233
4. Enable DSCP re‐marking globally. RS G8052(config)# qos dscp re­marking
5. Assign the DSCP re‐mark value.
RS G8052(config)# qos dscp dscp­mapping 40 9
RS G8052(config)# qos dscp dscp­mapping 46 9
6. Assign strict priority to VoIP COS queue.
RS G8052(config)# qos transmit­queue weight­cos 7 0
7. Map priority value to COS queue for non‐VoIP traffic.
RS G8052(config)# qos transmit­queue mapping 1 1
8. Assign weight to the non‐VoIP COS queue.
RS G8052(config)# qos transmit­queue weight­cos 1 2
234
G8052 Application Guide for ENOS 8.4
Using 802.1p Priority to Provide QoS
The G8052 provides Quality of Service functions based on the priority bits in a packet’s VLAN header. (The priority bits are defined by the 802.1p standard within the IEEE 802.1Q VLAN header.) The 802.1p bits, if present in the packet, specify the priority to be given to packets during forwarding. Packets with a numerically higher (non‐zero) priority are given forwarding preference over packets with lower priority value. The IEEE 802.1p standard uses eight levels of priority (0‐7). Priority 7 is assigned to highest priority network traffic, such as OSPF or RIP routing table updates, priorities 5‐6 are assigned to delay‐sensitive applications such as voice and video, and lower priorities are assigned to standard applications. A value of 0 (zero) indicates a “best effort” traffic prioritization, and this is the default when traffic priority has not been configured on your network. The switch can filter packets based on the 802.1p values. Figure 24. Layer 2 802.1q/802.1p VLAN tagged packet DMAC SMAC
SFD
Preamble
Priority
7
6
Tag
FCS
E Type Data
VLAN Identifier (VID)
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Ingress packets receive a priority value, as follows: 
Tagged packets—switch reads the 802.1p priority in the VLAN tag. 
Untagged packets—switch tags the packet and assigns an 802.1p priority value, based on the port’s default 802.1p priority. Egress packets are placed in a COS queue based on the priority value, and scheduled for transmission based on the scheduling weight of the COS queue.
To configure a port’s default 802.1p priority value, use the following commands: RS G8052(config)# interface port 1
RS G8052(config­if)# dot1p <802.1p value (0‐7)>
RS G8052(config­if)# exit
© Copyright Lenovo 2016
Chapter 13: Quality of Service
235
Queuing and Scheduling
The G8052 has 8 output Class of Service (COS) queues per port. If CEE is enabled, this is changed to 3 queues per port and ETS is then used to configure the scheduling in a manner different than what is described in this section. Each packet’s 802.1p priority determines its COS queue, except when an ACL action sets the COS queue of the packet.
You can configure the following attributes for COS queues:

Map 802.1p priority value to a COS queue

Define the scheduling weight of each COS queue
You can map 802.1p priority value to a COS queue, as follows: RS G8052(config)# qos transmit­queue mapping <802.1p priority value (0‐7)> <COS queue (0‐7)>
To set the COS queue scheduling weight, use the following command:
RS G8052(config)# qos transmit­queue weight­cos <COSq number> <COSq weight (0‐15)>
Control Plane Protection
Control plane receives packets that are required for the internal protocol state machines. This type of traffic is usually received at low rate. However, in some situations such as DOS attacks, the switch may receive this traffic at a high rate. If the control plane protocols are unable to process the high rate of traffic, the switch may become unstable.
The control plane receives packets that are channeled through protocol‐specific packet queues. Multiple protocols can be channeled through a common packet queue. However, one protocol cannot be channeled through multiple packet queues. These packet queues are applicable only to the packets received by the software and does not impact the regular switching or routing traffic. Packet queue with a higher number has higher priority. You can configure the bandwidth for each packet queue. Protocols that share a packet queue will also share the bandwidth.
Use the following commands to configure the control plane protection (CoPP) feature: RS G8052(config)# qos protocol­packet­control packet­queue­map <0‐47>
<protocol> (Configure a queue for a protocol)
RS G8052(config)# qos protocol­packet­control rate­limit­packet­queue
<0‐47> <1‐10000> (Set the bandwidth for the queue,
in packets per second)
236
G8052 Application Guide for ENOS 8.4
WRED with ECN
Weighted Random Early Detection (WRED) is a congestion avoidance algorithm that helps prevent a TCP collapse, where a congested port indiscriminately drops packets from all sessions. The transmitting hosts wait to retransmit resulting in a dramatic drop in throughput. Often times, this TCP collapse repeats in a cycle, which results in a saw‐tooth pattern of throughput. WRED selectively drops packets before the queue gets full, allowing majority of the traffic to flow smoothly. WRED discards packets based on the CoS queues. Packets marked with lower priorities are discarded first. Explicit Congestion Notification (ECN) is an extension to WRED. For packets that are ECN‐aware, the ECN bit is marked to signal impending congestion instead of dropping packets. The transmitting hosts then slow down sending packets.
How WRED/ECN work together
For implementing WRED, you must define a profile with minimum threshold, maximum threshold, and a maximum drop probability. The profiles can be defined on a port or a CoS.
For implementing ECN, you require ECN‐specific field that has two bits—the ECN‐capable Transport (ECT) bit and the CE (Congestion Experienced) bit—in the IP header. ECN is identified and defined by the values in these bits in the Differentiated Services field of IP Header. Table 18 shows the combination values of the ECN bits.
Table 18. ECN Bit Setting
© Copyright Lenovo 2016
ECT Bit
CE Bit
Description
0
0
Not ECN‐capable
0
1
Endpoints of the transport protocol are ECN‐capable
1
0
Endpoints of the transport protocol are ECN‐capable
1
1
Congestion experienced
Chapter 13: Quality of Service
237
WRED and ECN work together as follows:

If the number of packets in the queue is less than the minimum threshold, packets are transmitted. This happens irrespective of the ECN bit setting, and on networks where only WRED (without ECN) is enabled.

If the number of packets in the queue is between the minimum threshold and the maximum threshold, one of the following occurs:


If the ECN field on the packet indicates that the endpoints are ECN‐capable and the WRED algorithm determines that the packet has likely been dropped based on the drop probability, the ECT and CE bits for the packet are changed to 1, and the packet is transmitted.

If the ECN field on the packet indicates that neither endpoint is ECN‐capable, the packet may be dropped based on the WRED drop probability. This is true even in cases where only WRED (without ECN) is enabled.

If the ECN field on the packet indicates that the network is experiencing congestion, the packet is transmitted. No further marking is required.
If the number of packets in the queue is greater than the maximum threshold, packets are dropped based on the drop probability. This is the identical treatment a packet receives when only WRED (without ECN) is enabled.
Configuring WRED/ECN
For configuring WRED, you must define a TCP profile and a non‐TCP profile. WRED prioritizes TCP traffic over non‐TCP traffic.
For configuring ECN, you must define a TCP profile. You don’t need a non‐TCP profile as ECN can be enabled only for TCP traffic.
If you do not configure the profiles, the profile thresholds are set to maximum value of 0x3FFF to avoid drops.
Note: WRED/ECN can be configured only on physical ports and not on LAG. WRED and ECN are applicable only to unicast traffic.
Consider the following guidelines for configuring WRED/ECN:
Profiles can be configured globally or per port. Global profiles are applicable to all ports.
 Always enable the global profile before applying the port‐level profile.

Note: You can enable the global profile and disable the port‐level profile. However, you must not enable the port‐level profile if the global profile is disabled.
WRED settings are dependent on Memory Management Unit (MMU) Settings. If you change the MMU setting, it could impact WRED functionality.
 You cannot enable WRED if you have QoS buffer settings such as Converged Enhanced Ethernet (CEE), Priority‐based Flow Control (PFC), or Enhanced Transmission Selection (ETS).  The number of WRED profiles per‐port must match the total number of COS Queues configured in the system.

238
G8052 Application Guide for ENOS 8.4

If you have configured a TCP profile and enabled ECN, ECN marking happens when traffic experiencing congestion is TCP, or a mix of TCP and non‐TCP traffic.
Configure a TCP profile only after enabling ECN on the interface.
 You can apply TCP and non‐TCP profile configurations irrespective of ECN status (enabled/disabled).

WRED/ECN Configuration Example
Follow these steps to enable WRED/ECN and configure a global and/or port‐level profile. If you configure global and port‐level profile, WRED/ECN uses the port‐level profile to make transmit/drop decisions when experiencing traffic congestion.
Configure Global Profile for WRED
1. Enable WRED globally.
RS G8052(config)# qos random­detect enable
2. Enable a transmit queue.
RS G8052(config)# qos random­detect transmit­queue 0 enable
3. Configure WRED thresholds (minimum, maximum, and drop rate) for TCP traffic.
RS G8052(config)# qos random­detect transmit­queue 0 tcp min­threshold 1 max­threshold 2 drop­rate 3
Note: Percentages are of Average Queue available in hardware and not percentages of traffic.
4. Configure WRED thresholds (minimum, maximum, and drop rate) for non‐TCP traffic.
RS G8052(config)# qos random­detect transmit­queue 0 non­tcp min­threshold 4 max­threshold 5 drop­rate 6
5. Select the port.
RS G8052(config)# interface port 1
6. Enable WRED for the port.
RS G8052(config­if)# random­detect enable
RS G8052(config­if)# exit
© Copyright Lenovo 2016
Chapter 13: Quality of Service
239
Configure Port-level Profile for WRED
1. Enable WRED globally.
RS G8052(config)# qos random­detect enable
2. Select the port.
RS G8052(config)# interface port 1
3. Enable WRED for the port .
RS G8052(config­if)# random­detect enable
4. Enable a transmit queue.
RS G8052(config­if)# random­detect transmit­queue 0 enable
5. Configure WRED thresholds (minimum, maximum, and drop rate) for TCP traffic.
RS G8052(config­if)# random­detect transmit­queue 0 tcp min­threshold 11 max­threshold 22 drop­rate 33
Note: Percentages are of Average Queue available in hardware and not percentages of traffic.
6. Configure WRED thresholds (minimum, maximum, and drop rate) for non‐TCP traffic.
RS G8052(config­if)# random­detect transmit­queue 0 non­tcp min­threshold 44 max­threshold 55 drop­rate 66
RS G8052(config­if)# exit
Configure Global Profile for ECN
1. Enable ECN globally.
RS G8052(config)# qos random­detect ecn enable
2. Enable a transmit queue.
RS G8052(config)# qos random­detect transmit­queue 0 enable
3. Configure ECN thresholds (minimum, maximum, and drop rate) for TCP traffic.
RS G8052(config)# qos random­detect transmit­queue 0 tcp min­threshold 1 max­threshold 2 drop­rate 3
Note: Percentages are of Average Queue available in hardware and not percentages of traffic.
240
G8052 Application Guide for ENOS 8.4
4. Select the port.
RS G8052(config)# interface port 1
5. Enable ECN for the port.
RS G8052(config­if)# random­detect ecn enable
RS G8052(config­if)# exit
Configure Port-level Profile for ECN
1. Enable ECN globally.
RS G8052(config)# qos random­detect ecn enable
2. Select the port.
RS G8052(config)# interface port 1
3. Enable ECN for the port.
RS G8052(config­if)# random­detect ecn enable
4. Enable a transmit queue.
RS G8052(config­if)# random­detect transmit­queue 0 enable
5. Configure ECN thresholds (minimum, maximum, and drop rate) for TCP traffic.
RS G8052(config­if)# random­detect transmit­queue 0 tcp min­threshold 11 max­threshold 22 drop­rate 33
RS G8052(config­if)# exit
Note: Percentages are of Average Queue available in hardware and not percentages of traffic.
© Copyright Lenovo 2016
Chapter 13: Quality of Service
241
Verify WRED/ECN
Use the following command to view global WRED/ECN information: RS G8052(config)# show qos random­detect
Current wred and ecn configuration:
Global ECN: Enable
Global WRED: Enable
TQ0:­WRED­TcpMinThr­TcpMaxThr­TcpDrate­NonTcpMinThr­NonTcpMaxThr­NonTcpDrate­
Ena 10 20 30 10 20 30
TQ1:­WRED­TcpMinThr­TcpMaxThr­TcpDrate­NonTcpMinThr­NonTcpMaxThr­NonTcpDrate­
Dis 0 0 0 0 0 0
TQ2:­WRED­TcpMinThr­TcpMaxThr­TcpDrate­NonTcpMinThr­NonTcpMaxThr­NonTcpDrate­
Dis 0 0 0 0 0 0
TQ3:­WRED­TcpMinThr­TcpMaxThr­TcpDrate­NonTcpMinThr­NonTcpMaxThr­NonTcpDrate­
Dis 0 0 0 0 0 0
TQ4:­WRED­TcpMinThr­TcpMaxThr­TcpDrate­NonTcpMinThr­NonTcpMaxThr­NonTcpDrate­
Dis 0 0 0 0 0 0
TQ5:­WRED­TcpMinThr­TcpMaxThr­TcpDrate­NonTcpMinThr­NonTcpMaxThr­NonTcpDrate­
Dis 0 0 0 0 0 0
TQ6:­WRED­TcpMinThr­TcpMaxThr­TcpDrate­NonTcpMinThr­NonTcpMaxThr­NonTcpDrate­
Dis 0 0 0 0 0 0
TQ7:­WRED­TcpMinThr­TcpMaxThr­TcpDrate­NonTcpMinThr­NonTcpMaxThr­NonTcpDrate­
Dis 0 0 0 0 0 0
Use the following command to view port‐level WRED/ECN information:
RS G8052(config)# show interface port 1 random­detect
Port: 1
ECN: Enable
WRED: Enable
TQ0:­WRED­TcpMinThr­TcpMaxThr­TcpDrate­NonTcpMinThr­NonTcpMaxThr­NonTcpDrate­
Dis 0 0 0 0 0 0
TQ1:­WRED­TcpMinThr­TcpMaxThr­TcpDrate­NonTcpMinThr­NonTcpMaxThr­NonTcpDrate­
Ena 4 5 6 1 2 3
TQ2:­WRED­TcpMinThr­TcpMaxThr­TcpDrate­NonTcpMinThr­NonTcpMaxThr­NonTcpDrate­
Dis 0 0 0 0 0 0
TQ3:­WRED­TcpMinThr­TcpMaxThr­TcpDrate­NonTcpMinThr­NonTcpMaxThr­NonTcpDrate­
Dis 0 0 0 0 0 0
TQ4:­WRED­TcpMinThr­TcpMaxThr­TcpDrate­NonTcpMinThr­NonTcpMaxThr­NonTcpDrate­
Dis 0 0 0 0 0 0
TQ5:­WRED­TcpMinThr­TcpMaxThr­TcpDrate­NonTcpMinThr­NonTcpMaxThr­NonTcpDrate­
Dis 0 0 0 0 0 0
TQ6:­WRED­TcpMinThr­TcpMaxThr­TcpDrate­NonTcpMinThr­NonTcpMaxThr­NonTcpDrate­
Dis 0 0 0 0 0 0
TQ7:­WRED­TcpMinThr­TcpMaxThr­TcpDrate­NonTcpMinThr­NonTcpMaxThr­NonTcpDrate­
Dis 0 0 0 0 0 0
242
G8052 Application Guide for ENOS 8.4
Part 4: Advanced Switching
Features
© Copyright Lenovo 2016
243
244
G8052 Application Guide for ENOS 8.4
Chapter 14. OpenFlow
This document describes how you can create an OpenFlow Switch instance on the Lenovo RackSwitch G8052.
The following topics are discussed in this document: © Copyright Lenovo 2016

“OpenFlow Overview” on page 246

“Switch Profiles” on page 247

“OpenFlow Versions” on page 248

“OpenFlow Instance” on page 249

“Flow Tables” on page 250

“Static Flows” on page 252

“Table‐Miss” on page 257

“Fail Secure Mode” on page 258

“Emergency Mode” on page 259

“OpenFlow Ports” on page 261

“sFlow Compatibility” on page 264

“OpenFlow Groups” on page 265

“Configuring OpenFlow” on page 266

“Feature Limitations” on page 271
245
OpenFlow Overview
OpenFlow architecture consists of a control plane residing outside of the switch (typically on a server) and a data plane residing in the switch. The control plane is called OpenFlow controller. The data plane which resides in the switch consists of a set of flows which determine the forwarding of data packets.
The OpenFlow protocol is described in the OpenFlow Switch Specification 1.0.0 and OpenFlow Switch Specification 1.3.1.
An OpenFlow network consists of simple flow‐based switches in the data path, with a remote controller to manage all switches in the OpenFlow network.
OpenFlow maintains a TCP channel for communication of flow management between the controller and the switch. All controller‐switch communication takes place over the switchʹs management network. 246
G8052 Application Guide for ENOS 8.4
Switch Profiles
The RackSwitch G8052 can be used for configuring OpenFlow and legacy switching features simultaneously. However, Layer 2 and Layer 3 switching features can be configured only on the ports that are not OpenFlow ports. Legacy switching ports and OpenFlow ports do not communicate with each other. Alternately, the switch can be configured as an OpenFlow‐only switch if you do not need to configure legacy switching features. Based on your requirement, select the switch boot profile using the following commands:

OpenFlow‐only: RS G8052(config)# boot profile openflow
The switch will operate only in OpenFlow environment. None of the legacy switching features will be supported.

OpenFlow and Legacy Switching: RS G8052(config)# boot profile default
Legacy switching features can be configured on the non‐OpenFlow ports. By default, the switch boots in this profile.
Reload the switch to apply boot profile changes. © Copyright Lenovo 2016
Chapter 14: OpenFlow
247
OpenFlow Versions
The RackSwitch G8052 can be configured to run either version 1.0 or version 1.3 of the OpenFlow standard. By default, the switch uses OpenFlow 1.0. To shift between versions, use the following commands:

RS G8052(config)# boot openflow v1
The switch will run OpenFlow 1.0 after reboot. This version does not support the use of groups, static portchannels, or static LACP LAGs in OpenFlow instances (see “Configuring OpenFlow” on page 266).

RS G8052(config)# boot openflow v13
The switch will run OpenFlow 1.3 after reboot. This version does not support emergency flow tables (see “Emergency Mode” on page 259).
OpenFlow 1.3 includes (but not limited to) the following key features:
248

Static portchannels and static LACP LAGs

MAC address/IP address masking

Flexible Table Miss and Fail Secure

Static CLI for Flow Programming

OpenFlow Groups

FDB aging timer

OpenFlow 1.0 backwards compatibility
G8052 Application Guide for ENOS 8.4
OpenFlow Instance
The G8052 supports up to two instances of the OpenFlow protocol. Each instance appears as a switch to the controller. Instances on the same switch can be connected to different networks. Each instance maintains a separate TCP channel for communication of flow management between controller and switch. Each instance supports up to four controllers. However, only one controller per instance is active at any time.
Global OpenFlow configuration applies to all instances. OpenFlow parameters for an instance can be configured using the command: RS G8052(config)# openflow instance <instance ID>.
OpenFlow ports cannot be shared between instances. © Copyright Lenovo 2016
Chapter 14: OpenFlow
249
Flow Tables
A set of a flow identification condition and an action towards a flow is called flow entry, and the database that stores the entries is called the flow table. A flow is defined as all the packets matching a flow entry in an OpenFlow flow table. Each flow entry includes:

Qualifiers ‐ These are header fields that are matched with a packet.

Actions to be performed when a packet matches the qualifiers.
The controller decides which flows to admit and the path their packets follow.
The switch classifies the flows as ACL‐based, or FDB‐based. When the switch operates in OpenFlow boot profile (See “Switch Profiles” on page 247), a maximum of 2000 ACL‐based flows, 1024 FDB multicast flows, 30976 FDB unicast flows. When the switch operates in default boot profile, a maximum of 1500 ACL‐based flows, 1024 FDB multicast flows, and 30976 FDB unicast flows are available. The instances share these flows dynamically. To guarantee a specific number of flows to an instance, use the following commands:

OpenFlow boot profile: RS
RS
RS
RS

G8052(config)# openflow instance <instance ID>
G8052(config­openflow­instance)# max­flow­acl <0‐2000> G8052(config­openflow­instance)# max­flow­mcast­fdb <0‐1024>
G8052(config­openflow­instance)# max­flow­ucast­fdb <0‐30976>
Default boot profile: RS G8052(config)# openflow instance <instance ID>
RS G8052(config­openflow­instance)# max­flow­acl <0‐1500> RS G8052(config­openflow­instance)# max­flow­mcast­fdb <0‐30976>
Note: When the switch operates in default boot profile, the number of FDB flows to an instance cannot be guaranteed.
In version 1.0 of the OpenFlow standard, the G8052 supports two flow tables per switch instance; basic flow table and emergency flow table. Actions are applied to packets that match the flow entry. This is done in the data path.
This system identifies packets as a flow by matching parameters in the following fields: 250

Ingress port

Source MAC (SMAC)

Destination MAC (DMAC)

Ether Type

VLAN TAG – Single VLAN tag – VLAN ID and Priority

IP address (source IP and destination IP)

IP Protocol

DSCP bits
G8052 Application Guide for ENOS 8.4

Layer 4 Port (TCP, UDP)

ICMP code and type

If EtherType is ARP, the specified ARP type (request/reply) or SIP in the ARP payload can be used to match a packet. Once a packet arrives, the switch searches the flow table. When a flow entry is hit in the search, the packet is processed according to the action specified in the flow entry. © Copyright Lenovo 2016
Chapter 14: OpenFlow
251
Static Flows
You can configure static flow entries for OpenFlow instances. The switch forwards traffic based on these entries even if it is not connected to a controller. Up to 1000 static ACL entries across all instances can be configured. An OpenFlow controller cannot modify or delete these entries. Static flow entries can replace entries installed by a controller. Static flow entries are not lost when the switch is reloaded.
Static flow entries are based on the following qualifiers, actions, and options: Table 19. Static Flow Entry Qualifiers in OpenFlow 1.0
Qualifier
Description
ingress‐port
port of the instance
src‐mac
source MAC address
dst‐mac
destination MAC address
vlan‐priority
802.1p(0‐7)
src‐ip
source IP address
dst‐ip
destination IP address
src‐port
Layer 4 source port (0‐65535)
dst‐port
Layer 4 destination port (0‐65535)
ether‐type
ʺarpʺ/ʺ0806ʺ or ʺipʺ/ʺ0800ʺ or (hex‐value < = 65535)
protocol
ʺtcpʺ or ʺudpʺ or 0‐255
tos
IP TOS (0‐255)
type
ʺrequestʺ or ʺreplyʺ (can be set only if ether type is ARP)
all
all qualifiers or any qualifier
Table 20. Static Flow Entry Qualifiers in OpenFlow 1.3
252
Qualifier
Description
in‐port
switch input port
in‐portchannel
switch input static LAG (portchannel) or static LACP LAG
in‐phy‐port
switch physical input port, valid only when in‐port is specified
eth‐src
source MAC address and mask
eth‐dst
destination MAC address and mask
vlan‐vid
VLAN identifier (untagged, tagged or <0‐4094>)
G8052 Application Guide for ENOS 8.4
Table 20. Static Flow Entry Qualifiers in OpenFlow 1.3
Qualifier
Description
vlan‐pcp
802.1p(0‐7)
ipv4‐src
source IPv4 address and mask
ipv4‐dst
destination IPv4 address and mask
tcp‐src
TCP source port (0‐65535)
tcp‐dst
TCP destination port (0‐65535)
udp‐src
UDP source port (0‐65535)
udp‐dst
UDP destination port (0‐65535)
icmpv4‐type
ICMPv4 type
icmpv4‐code
ICMPv4 code
eth‐type
ʺarpʺ/ʺ0806ʺ or ʺipʺ/ʺ0800ʺ or (hex‐value < =65535)
ip‐proto
ʺtcpʺ or ʺudpʺ or 0‐255
ip‐dscp
IP DSCP (6 bits in ToS field)
arp‐op
ʺrequestʺ or ʺreplyʺ (can be set only if eth‐type is ARP)
all
all qualifiers or any qualifier
Table 21. Static Flow Entry Actions in OpenFlow 1.0
Action
Description
out‐put
ʺallʺ,ʺin‐portʺ,ʺfloodʺ,ʺcontrollerʺ or a valid port
set‐src‐mac
change source MAC address
set‐dst‐mac
change destination MAC address
strip‐vlan‐id
strip VLAN
set‐vlan‐id
set VLAN ID
set‐vlan‐priority
set 802.1p priority (0‐7)
set‐nw‐tos
set IP TOS (0‐255)
drop
drop the packet
Table 22. Static Flow Entry Actions in OpenFlow 1.3
© Copyright Lenovo 2016
Action
Description
output
physical ports
reserved ports: all, controller, in‐port
output‐portchannel
Logical ports: static LAG (portchannel) or static LACP LAG
set‐eth‐src
change source MAC address
set‐eth‐dst
change destination MAC address
Chapter 14: OpenFlow
253
Table 22. Static Flow Entry Actions in OpenFlow 1.3
Action
Description
push‐vlan
push a new VLAN tag, 0x8100
pop‐vlan
pop the VLAN tag
set‐vlan‐vid
set VLAN ID, <0‐4094>
set‐vlan‐pcp
set 802.1p priority (0‐7)
set‐ip‐dscp
Set IP DSCP (0‐63), 6 highest bits in TOS
drop
drop the packet
The set‐field action includes set‐eth‐src, set‐eth‐dst, set‐vlan‐vid, set‐vlan‐pcp, set‐ip‐dscp. They may be used in any order.
The output action includes output and output‐portchannel. They may be used in any order.
Table 23. Static Flow Entry Options
Option
Description
max‐len
maximum length of flow to send to controller
Port Membership
When static flow entries are configured, port membership changes are handled as follows: 
If a port is the “in‐port” or “out‐port” in a static flow entry, the port membership cannot be changed.

When a port membership changes, the ingress bitmap of static entries with in‐port ANY will be updated.

When a port membership changes, the egress bitmap of static entries with redirect output FlOOD/ANY will be updated.
FDB Aging and ECMP with OpenFlow
You can enable FDB aging in OpenFlow using the following commands:
RS G8052(config)# interface port <port number>
RS G8052(config­if)# openflow fdb­aging
To enable Layer 2 ECMP for OpenFlow station moves, use the following commands:
RS G8052(config)# interface port <port number>
RS G8052(config­if)# openflow static­station­move
254
G8052 Application Guide for ENOS 8.4
Static Flow Examples
Following are examples of static flow entries for OpenFlow 1.0:

Basic ACL flow: RS G8052(config­openflow­instance)# static­table add index 1 match ingress­port=1 actions out­put=10 priority 12345

Flow with multiple qualifiers and actions: RS G8052(config­openflow­instance)# static­table add index 2 match vlan­id=1,dst­mac=00:00:00:00:00:01 actions set­vlan­priority=3,out­put=20 priority 1000

Flow with action: output to controller: RS G8052(config­openflow­instance)# static­table add index 3 match all actions out­put=controller options max­len=65534 priority 1000
Static ACL flow entries can be deleted using the command: RS G8052(config­openflow­instance)# static­table remove index <index number>
Following are examples of static flow entries for OpenFlow 1.3:

Basic ACL flow: RS G8052(config­openflow­instance)# static­table add index 1 match in­port=41 actions output=50 priority 12345

Flow with multiple qualifiers and actions: RS G8052(config­openflow­instance)# static­table add index 2 match vlan­vid=1,eth­dst=00:00:00:00:00:01 actions set­vlan­pcp=3,output=50 priority 1000
Static ACL flow entries can be deleted using the command: RS G8052(config­openflow­instance)# static­table remove index <index number>
© Copyright Lenovo 2016
Chapter 14: OpenFlow
255
Static flow table information can be viewed using the following commands: In OpenFlow version 1.0: RS G8052(config­openflow­instance)# show openflow table
Openflow Instance Id: 1
BASIC FLOW TABLE
STATIC FLOWS
Flow:1 Index:1
Filter Based, priority:12345
QUALIFIERS: ingress­port:1
ACTION: output:10
STATS: packets=0, bytes=0
Flow:2 Index:2
Filter Based, priority: 1000
QUALIFIERS: vlan­id: 1
dst­mac:00­00­00­00­00­01
ACTION: set­vlan­priority=3, output:20
STATS: packets=0, bytes=0
Flow:3 Index:3
Filter Based, priority: 1000
QUALIFIERS:
ACTION: output:CONTROLLER [Max Len: 65534 / ­ bytes (C/S)]
STATS: packets=26, bytes=1776
Openflow Instance Id: 2
BASIC FLOW TABLE is Empty
In OpenFlow version 1.3: RS G8052(config­openflow­instance)# show openflow table
Openflow Instance Id: 1
STATIC FLOWs
Flow 1, Index:2, Filter Based, priority:1000
QUALIFIERS: eth­dst:00:00:00:00:00:01
vlan­vid:1
Instruction: apply_action
ACTION: set­vlan­pcp=3, output:50
STATS: packets=0, bytes=0
Flow 2, Index:1, Filter Based, priority:12345
QUALIFIERS: in­port:41
Instruction: apply_action
ACTION: output:50
STATS: packets=0, bytes=0
Openflow instance 2 is currently disabled
256
G8052 Application Guide for ENOS 8.4
Table-Miss
In OpenFlow 1.3, if a match is not found for an arriving packet, the packet is either dropped or sent to the controller. If sent to the controller, the controller decides which action(s) to perform on all packets from the same flow. The decision is then sent to the switch and cached as an entry in the switch instance’s flow table. If the controller decides to add the flow, it sends a flow add message to the switch. The switch then adds the flow in its flow table. The next arriving packet that belongs to the same flow is then forwarded at line‐rate through the switch without consulting the controller.
By default, packets that don’t match any of the existing flow entries are dropped. To set up an OpenFlow instance to send non‐matching packets to the controller instead of dropping them, use the following commands:
RS G8052(config)# openflow instance <instance ID>
RS G8052(config­openflow­instance)# table­miss controller
© Copyright Lenovo 2016
Chapter 14: OpenFlow
257
Fail Secure Mode
In OpenFlow 1.3, if contact with all controllers is lost, the switch automatically enters a fail secure mode. In this mode, the switch continues to operate based on the existing flow entries until they expire (according to the configured flow timeout value), while packets and messages destined to the controllers are dropped. When a connection to a controller is reestablished, the controller has the option to either delete or keep any remaining flow entries.
258
G8052 Application Guide for ENOS 8.4
Emergency Mode
Note: Emergency Mode is supported only in version 1.0 of the OpenFlow standard.
By default, Emergency mode is disabled. In this state, if the connection to the controller fails, the switch will behave as described in Fail Secure mode for Openflow 1.3.
To enable Emergency mode, use the following command: RS G8052(config)# openflow instance <instance ID>
RS G8052(config­openflow­instance)# emergency
In Emergency mode enabled state, if the connection to the controller fails, the switch tries to establish connection with any of the other configured controllers. If it is unable to connect with any controller, it enters Emergency mode. It replaces the flow entries with the entries from the emergency flow table.
The switch stays in the Emergency mode for the time configured as the Emergency timeout interval (default value is 30 seconds), after which the switch tries to establish connection with any configured controller. 
If connection with a controller is established, the switch exits Emergency mode. Entries in the Emergency flow table are retained. If desired, the controller may delete all the emergency flow entries. 
If connection with a controller is not established, the switch stays in Emergency mode and continues to forward packets based on the Emergency flows. It retries to establish a connection with a controller every time the Emergency timeout interval expires.
Emergency mode can be activated or deactivated per instance. To activate Emergency mode on an instance, use the following command: RS G8052# openflow instance <instance ID> enter­emergency
To deactivate Emergency mode on an instance, use the following command: RS G8052# no openflow instance <instance ID> enter­emergency
© Copyright Lenovo 2016
Chapter 14: OpenFlow
259
Table 24 displays an example of emergency flows created: Table 24. Emergency Flows
RS G8052(config)# show openflow table Openflow Instance Id: 1
BASIC FLOW TABLE
Flow:1 FDB Based, priority: 1000, hard­time­out: 0
QUALIFIERS: dst­mac:01­02­03­05­06­00, vlan­id: 100 ACTION: out­port:21
Flow:2 Filter Based, priority:32768, hard­time­out: 0, idle­time­out: 0
QUALIFIERS: vlan­id: 100
dst­mac:01­02­03­66­76­00
ACTION: output:22
STATS: packets=0, bytes=0 EMERGENCY FLOW TABLE
Flow:1 FDB Based, priority: 1000, hard­time­out: 0
QUALIFIERS: dst­mac:01­02­03­66­06­00, vlan­id: 100 ACTION: out­port:21
Flow:2 Filter Based, priority:32768, hard­time­out: 0, idle­time­out: 0
QUALIFIERS: vlan­id: 100
dst­mac:01­02­03­66­06­00
ACTION: output:22
Openflow Instance Id: 2
BASIC FLOW TABLE
Flow:1 FDB Based, priority: 1000, hard­time­out: 0
QUALIFIERS: dst­mac:01­55­03­11­96­00, vlan­id: 200 ACTION: out­port:31
EMERGENCY FLOW TABLE
Flow:1 FDB Based, priority: 1000, hard­time­out: 0
QUALIFIERS: dst­mac:01­55­03­11­16­00, vlan­id: 200 ACTION: out­port:31
260
G8052 Application Guide for ENOS 8.4
OpenFlow Ports
When OpenFlow is enabled, all OpenFlow instance member ports become OpenFlow ports. OpenFlow ports have the following characteristics: 
Learning is turned off.

Flood blocking is turned on.

Spanning Tree Protocol (STP) is disabled.
The switch communicates with OpenFlow controllers through controller management ports or through dedicated out‐of‐band management ports on the switch. All OpenFlow ports, except controller management ports, must be members of VLAN 1. Controller management ports can be members of any VLAN except VLAN 1.
Note: When the switch operates in the default boot profile, we recommend that you use a non‐OpenFlow port to connect the switch with the controller. Use the following command to view port information: RS G8052(config)# show interface information
For each OpenFlow instance, when you configure the controller IP address and port, the switch establishes a TCP connection with the controller for flow control and management. See Step 3 on page 266. The switch supports up to four controllers per instance. The default controller port is 6633 and is reachable via any in‐band port configured as management port or through dedicated out‐of‐band management port (MGT). The controller management ports must not be members of an OpenFlow instance. You can use a controller to manage and control multiple instances. Use the following command to configure a data port as a controller management port (available only in OpenFlow boot profile): RS G8052(config)# openflow mgmtport <port number>
Note: In default boot profile, when you disable OpenFlow, the OpenFlow ports become legacy switch ports and are added to the default VLAN 1.
OpenFlow Edge Ports
You can configure a port as an OpenFlow edge port. Edge ports are connected to either non‐OpenFlow switches or servers. OpenFlow edge ports have the following characteristics:

Flood blocking is turned on.

MAC learning is turned on.
Use the following command to configure a port as an edge port: RS G8052(config)# openflow instance <instance ID>
RS G8052(config­openflow­instance)# edgeport <port number>
Note: Edge ports are not OpenFlow standard ports. You must configure edge ports only if the controller supports it.
© Copyright Lenovo 2016
Chapter 14: OpenFlow
261
You may also add an existing LAG to the edge ports list. To add either a static LAG (portchannel) or a static LACP LAG, use the following command:
RS G8052(config­openflow­instance)# edgeport portchannel <LAG ID>
where the LAG ID is derived from the original LAG configuration:

Static LAG (portchannel)
RS G8052(config)# portchannel <LAG ID> port <port list>

Static LACP LAG
RS G8052(config)# portchannel <LAG ID> lacp key <LACP admin key>
For more information about LAGs, see Chapter 10, “Ports and Link Aggregation.”
Link Aggregation
In OpenFlow 1.3, port LAGs can be added to OpenFlow instances. A LAG aggregates its member ports to form a logical port with increased bandwidth. You can add an existing static LAG (portchannel) or static LACP LAG to an OpenFlow instance using the following commands: RS G8052(config)# openflow instance <instance ID>
RS G8052(config­openflow­instance)# member portchannel <LAG ID>
where the LAG ID (the logical port ID) is derived from the original LAG configuration, based on the LAG type:

Static LAG (portchannel)
RS G8052(config)# portchannel <LAG ID> port <port list>

Static LACP LAG
RS G8052(config)# portchannel <LAG ID> lacp key <LACP admin key>
Note: For more information about configuring LAGs, see Chapter 10, “Ports and Link Aggregation.”
Once added to the instance, the LAG ports inherit the OpenFlow data properties such as MAC learning turned off, flood blocking turned on, and STP disabled.
The LAG link remains active as long as at least one member port is up. The LAG link speed is an aggregation of the speed of the individual member ports. If any port in the LAG goes down, the overall LAG link speed is decreased accordingly.
To add a static LAG or static LACP LAG to the edge ports list, use the following command:
RS G8052(config­openflow­instance)# edgeport portchannel <LAG ID>
262
G8052 Application Guide for ENOS 8.4
Data Path ID
The data path ID—automatically computed—is a combination of two bytes of the instance ID and six bytes of the switch MAC address. Alternately, the data path ID can be manually configured using the following command. Each instance on the switch must have a unique data path ID: RS G8052(config)# openflow instance <instance ID>
RS G8052(config­openflow­instance)# dpid <Data path ID>
0x)
(Hex string starting with Note: If the data path ID is changed, the switch instance closes the active connection and reconnects with the modified data path ID.
© Copyright Lenovo 2016
Chapter 14: OpenFlow
263
sFlow Compatibility
OpenFlow ports that are set for sFlow sampling will send incoming sample packets to both the sFlow server or analyzer and the OpenFlow controller as “packet‐in.” sFlow servers must be configured as reachable over a management port or a non‐OpenFlow data port.
Unicast FDB flows support ingress and egress sampling.
ACL‐based flows, multicast FDB‐based flows, packet‐in, send‐to‐controller, and mirror‐to‐controller flows support only ingress sampling.
264
G8052 Application Guide for ENOS 8.4
OpenFlow Groups
In OpenFlow 1.3, the RackSwitch G8052 supports OpenFlow groups based on the OpenFlow 1.3.1 specification. The following OpenFlow group features are supported:
© Copyright Lenovo 2016

Group types: ALL and INDIRECT

Up to 256 groups per instance

Group operations: ADD, MODIFY, and DELETE

Support for group multipart messages: group counter statistics, group description, and group features

Flows: ACL and FDB

Port types: Physical port, logical port (static portchannel or static LACP LAG)
Chapter 14: OpenFlow
265
Configuring OpenFlow
The RackSwitch G8052 is capable of operating both in normal switching environment (default boot profile) and in OpenFlow switch environment (OpenFlow boot profile). Note: If you disable OpenFlow, you must reboot the switch to resume normal switch environment operations.
Perform the following steps to configure an OpenFlow switch instance. 1. Enable OpenFlow:
RS G8052(config)# openflow enable
2. Create an OpenFlow switch instance and add data ports: RS G8052(config)# openflow instance <1‐2>
RS G8052(config­openflow­instance)# member <port number or range>
In version 1.3 of the OpenFlow standard, you can also add static portchannels or static LACP LAGs to the instance:
RS G8052(config­openflow­instance)# member portchannel <1‐104>
3. Configure a controller for the OpenFlow switch instance: RS G8052(config­openflow­instance)# controller <1‐4> address <IP address> RS G8052(config­openflow­instance)# controller <1‐4> port <1‐65535>
4. Enable the OpenFlow switch instance: RS G8052(config­openflow­instance)# enable
The switch is ready to perform switching functions in an OpenFlow environment. 5. Verify OpenFlow configuration: RS G8052(config)# show openflow instance <instance ID> information
Configuration Example 1 - OpenFlow Boot Profile
The following example includes steps to configure an OpenFlow switch instance when the switch operates in OpenFlow boot profile. Configure OpenFlow instance 1, which connects with two controllers via in‐band management ports, and OpenFlow instance 2, which connects with two controllers via in‐band management ports.
266
G8052 Application Guide for ENOS 8.4
1. Configure IP interface 1 for in‐band connection: RS
RS
RS
RS
RS
RS
G8052(config)# vlan 3000
G8052(config­vlan)# exit
G8052(config)# interface port 3
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 3000
G8052(config­if)# exit
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip address 172.21.100.1 255.255.0.0 enable
G8052(config­ip­if)# vlan 3000
G8052(config­ip­if)# exit
2. Configure IP interface 2 for in‐band connection: RS
RS
RS
RS
RS
RS
G8052(config)# vlan 4000
G8052(config­vlan)# exit
G8052(config)# interface port 4
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 4000
G8052(config­if)# exit
RS
RS
RS
RS
G8052(config)# interface ip 2
G8052(config­ip­if)# ip address 172.22.100.1 255.255.0.0 enable
G8052(config­ip­if)# vlan 4000
G8052(config­ip­if)# exit
3. Enable OpenFlow globally:
RS G8052(config)# openflow enable
4. Configure OpenFlow in‐band management ports: RS G8052(config)# openflow mgmtport 3,4(Switch can connect with the controllers via port 3 and 4, which are connected to the controller networks)
Note: Step 5 is not required when the switch operates in default boot profile.
5. Create OpenFlow switch instance 1 and add ports: RS G8052(config)# openflow instance 1
(Create OpenFlow instance 1)
RS G8052(config­openflow­instance)# member 17,18,19­25(Add ports 17,18, andport range 19 through 25 as members of OpenFlow instance 1)
6. Configure controller 1 IP address using in‐band management port: RS G8052(config­openflow­instance)# controller 1 address 172.21.100.73
(Switch connects with controller 1 via the in‐band management port configured in Step 4; default controller port is used in this example)
© Copyright Lenovo 2016
Chapter 14: OpenFlow
267
7. Enable OpenFlow instance 1: RS G8052(config­openflow­instance)# enable
RS G8052(config­openflow­instance)# exit
8. Create OpenFlow switch instance 2 and add member ports: RS G8052(config)# openflow instance 2
(Create OpenFlow instance 2)
RS G8052(config­openflow­instance)# member 26,27,28­30
(Addports 26,27, andport range 28 through 30 as members of OpenFlow instance 2)
9. Configure controller 1 IP address using in‐band management port: RS G8052(config­openflow­instance)# controller 1 address 172.21.100.73
(Switch connects with controller 1 via the in‐band management port configured in Step 4; default controller port is used in this example)
10. Enable OpenFlow instance 2: RS G8052(config­openflow­instance)# enable
11. View OpenFlow Configuration: RS G8052(config)# show running­config
268
G8052 Application Guide for ENOS 8.4
Configuration Example 2 - Default Boot Profile
The following example includes steps to configure an OpenFlow switch instance when the switch operates in Default boot profile.
1. Configure IP interface 1 for in‐band connection: RS
RS
RS
RS
RS
RS
G8052(config)# vlan 3000
G8052(config­vlan)# exit
G8052(config)# interface port 3
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 3000
G8052(config­if)# exit
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip address 172.21.100.1 255.255.0.0 enable
G8052(config­ip­if)# vlan 3000
G8052(config­ip­if)# exit
2. Configure IP interface 2 for in‐band connection: RS
RS
RS
RS
RS
RS
G8052(config)# vlan 4000
G8052(config­vlan)# exit
G8052(config)# interface port 6
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 4000
G8052(config­if)# exit
RS
RS
RS
RS
G8052(config)# interface ip 2
G8052(config­ip­if)# ip address 172.22.100.1 255.255.0.0 enable
G8052(config­ip­if)# vlan 4000
G8052(config­ip­if)# exit
3. Enable OpenFlow globally:
RS G8052(config)# openflow enable
4. Create OpenFlow switch instance 1 and add data ports: RS G8052(config)# openflow instance 1
(Create OpenFlow instance 1)
RS G8052(config­openflow­instance)# member 17,18,19­25(Addports 17,18, andport range 19 through 25 as members of OpenFlow instance 1)
5. Configure controller 2 IP address using in‐band management port: RS G8052(config­openflow­instance)# controller 2 address 172.21.100.73
(Switch connects with controller 2 via the in‐band management port; default controller port is used in this example)
6. Enable OpenFlow instance 1: RS G8052(config­openflow­instance)# enable
RS G8052(config­openflow­instance)# exit
© Copyright Lenovo 2016
Chapter 14: OpenFlow
269
7. Create OpenFlow switch instance 2 and add data ports: RS G8052(config)# openflow instance 2
(Create OpenFlow instance 2)
RS G8052(config­openflow­instance)# member 26,27,28­32
(Addports 26,27, andport range 28 through 32 as members of OpenFlow instance 2)
8. Configure controller 1 IP address using in‐band management port: RS G8052(config­openflow­instance)# controller 1 address 172.21.100.73
(Switch connects with controller 1 via the in‐band management port; default controller port is used in this example)
9. Configure controller 2 IP address using in‐band management port: RS G8052(config­openflow­instance)# controller 2 address 172.22.100.73
Switch connects with controller 2 via in‐band management port; default controller port is used in this example)
10. Enable OpenFlow instance 2: RS G8052(config­openflow­instance)# enable
RS G8052(config­openflow­instance)# exit
View OpenFlow Configuration: RS G8052(config)# show running­config
270
G8052 Application Guide for ENOS 8.4
Feature Limitations
When the switch is booted in the OpenFlow profile, it operates only in OpenFlow switch environment. None of the normal switching environment features are supported.
If the switch is booted in default profile, normal switching environment features can be configured on the non‐OpenFlow ports. However, the following features are not supported: © Copyright Lenovo 2016

ACLs

FCoE/CEE

Dynamic PBR

IPMC with IP options

IPv6

Management ACL

VLAG

VMap

VMready

vNIC
Chapter 14: OpenFlow
271
272
G8052 Application Guide for ENOS 8.4
Chapter 15. Virtualization
Virtualization allows resources to be allocated in a fluid manner based on the logical needs of the data center, rather than on the strict, physical nature of components. The following virtualization features are included in Lenovo Enterprise Network Operating System 8.4 on the RackSwitch G8052 (G8052):

Virtual Local Area Networks (VLANs)
VLANs are commonly used to split groups of networks into manageable broadcast domains, create logical segmentation of workgroups, and to enforce security policies among logical network segments.
For details on this feature, see Chapter 9, “VLANs.”

Link aggregation
A port LAG pools multiple physical switch ports into a single, high‐bandwidth logical link to other devices. In addition to aggregating capacity, LAGs provides link redundancy.
For details on this feature, see Chapter 10, “Ports and Link Aggregation.”

Virtual Link Aggregation (VLAGs)
With VLAGs, two switches can act as a single logical device for the purpose of establishing port aggregation. Active LAG links from one device can lead to both VLAG peer switches, providing enhanced redundancy, including active‐active VRRP configuration.
For details on this feature, see Chapter 12, “Virtual Link Aggregation Groups.”

VMready
The switch’s VMready software makes it virtualization aware. Servers that run hypervisor software with multiple instances of one or more operating systems can present each as an independent virtual machine (VM). With VMready, the switch automatically discovers virtual machines (VMs) connected to switch.
For details on this feature, see Chapter 17, “VMready.”

Edge Virtual Bridging (EVB)
An IEEE 802.1Qbg standard that simplifies network management by providing a standards‐based protocol that defines how virtual Ethernet bridges exchange configuration information. EVB bridges the gap between physical and virtual network resources by allowing networks to become virtual machine (VM)‐aware.
For details on this feature, see Chapter 18, “Edge Virtual Bridging.”
ENOS virtualization features provide a highly‐flexible framework for allocating and managing switch resources.
© Copyright Lenovo 2016
273
274
G8052 Application Guide for ENOS 8.4
Chapter 16. Stacking
This chapter describe how to implement the stacking feature in the Lenovo RackSwitch G8052. The following concepts are covered:
© Copyright Lenovo 2016

“Stacking Overview” on page 276

“Stack Membership” on page 278

“Configuring a Stack” on page 282

“Managing the Stack” on page 288

“Upgrading Software in an Existing Stack” on page 290

“Replacing or Removing Stacked Switches” on page 292

“Saving Syslog Messages” on page 296

“ISCLI Stacking Commands” on page 298
275
Stacking Overview
A stack is a group of up to eight RackSwitch G8052 switches with Lenovo Enterprise Network Operating System that work together as a unified system. A stack has the following properties, regardless of the number of switches included:

The network views the stack as a single entity.

The stack can be accessed and managed as a whole using standard switch IP interfaces configured with IPv4 addresses.

To get CLI access to Individual Member switches, a serial console cable must be plugged into the member switch. Telnet/SSH access to a member can then be obtained by connecting from the Master using the command:
connect <attached switch number>

Once the stacking links have been established (see the next section), the number of ports available in a stack equals the total number of remaining ports of all the switches that are part of the stack.

The number of available IP interfaces, VLANs, LAGs, LAG Links, and other switch attributes are not aggregated among the switches in a stack. A maximum of 128 IP interfaces can be configured, a maximum of 4095 VLANs are supported in stand‐alone mode, and a maximum of 1024 VLANs are supported in stacking mode.
Stacking Requirements
Before Enterprise NOS switches can form a stack, they must meet the following requirements:
276

All switches must be the same model (RackSwitch G8052).

Each switch must be installed with ENOS, version 8.4 or later. The same release version is not required, as the Master switch will push a firmware image to each differing switch which is part of the stack.

The recommended stacking topology is a bidirectional ring (see Figure 25 on page 284). To achieve this, two 10Gb Ethernet ports on each switch must be reserved for stacking. By default, 10Gb Ethernet ports 49‐50 are used.

The cables used for connecting the switches in a stack carry low‐level, inter‐switch communications as well as cross‐stack data traffic critical to shared switching functions. Always maintain the stability of stack links to avoid internal stack reconfiguration. G8052 Application Guide for ENOS 8.4
Stacking Limitations
The G8052 with ENOS 8.4 can operate in one of two modes:


Default mode, which is the regular stand‐alone (or non‐stacked) mode.
Stacking mode, in which multiple physical switches aggregate functions as a single switching device.
Note: There are two distinct software images for the G8052. One supports standalone operation only, and the other supports stacking only.
When in stacking mode, the following standalone features are not supported:





























ACL Logging
BCM Rate Control
Border Gateway Protocol (BGP)
Edge Control Protocol (ECP)
Equal‐Cost Multi‐Path (ECMP)
IGMP Relay, IGMP Querier, and IGMPv3
Internet Key Exchange version 2 (IKEv2)
IP Security (IPsec)
IP version 6 (IPv6)
Loop Guard
Loopback Interfaces
MAC address notification
MSTP
Network Configuration (NETCONF) Protocol
Operation, Administration, and Maintenance (OAM)
OSPF and OSPFv3
Port flood blocking
Precision Time Protocol (PTP)
Protocol‐based VLANs
RIP
Root Guard
Router IDs
Route maps
sFlow port monitoring
Static MAC address adding
Static multicast
Uni‐Directional Link Detection (UDLD)
VLAG
Virtual Router Redundancy Protocol (VRRP)
Note: In stacking mode, switch menus and command for unsupported features may be unavailable, or may have no effect on switch operation.
© Copyright Lenovo 2016
Chapter 16: Stacking
277
Stack Membership
A stack contains up to eight switches, interconnected by a stack LAG in a local ring topology (see Figure 25 on page 284). With this topology, only a single stack link failure is allowed.
An operational stack must contain one Master and one or more Members, as follows: 
Master
One switch controls the operation of the stack and is called the Master. The Master provides a single point to manage the stack. A stack must have one and only one Master. The firmware image, configuration information, and run‐time data are maintained by the Master and pushed to each switch in the stack as necessary. 
Member
Member switches provide additional port capacity to the stack. Members receive configuration changes, run‐time information, and software updates from the Master.

Backup
One member switch can be designated as a Backup to the Master. The Backup takes over control of the stack if the Master fails. Configuration information and run‐time data are synchronized with the Master.
The Master Switch
An operational stack can have only one active Master at any given time. In a normal stack configuration, one switch is configured as a Master and all others are configured as Members.
When adding new switches to an existing stack, the administrator must explicitly configure each new switch for its intended role as a Master (only when replacing a previous Master) or as a Member. All stack configuration procedures in this chapter depict proper role specification.
However, although uncommon, there are scenarios in which a stack may temporarily have more than one Master switch. If this occurs, the switch with the lowestMAC address will be chosen as the active Master for the entire stack. The selection process is designed to promote stable, predictable stack operation and minimize stack reboots and other disruptions.
Splitting and Merging One Stack
If stack links or Member switches fail, any Member which cannot access either the Master or Backup is considered isolated and will not process network traffic (see “No Backup” on page 281). Members which have access to a Master or Backup (or both), despite other link or Member failures, will continue to operate as part of their active stack. A Member that is isolated due to link failure resets itself. After it is up, if the link failure still exits, the Member stays in isolated state keeping all its data links disabled. Only the management and stacking links are enabled. If the Member was not configured when it went to isolated state, the Master pushes the configuration when the Member joins back the stack.
278
G8052 Application Guide for ENOS 8.4
If multiple stack links or stack Member switches fail, thereby separating the Master and Backup into separate sub‐stacks, the Backup automatically becomes an active Master for the partial stack in which it resides. Later, if the topology failures are corrected, the partial stacks will merge, and the two active Masters will come into contact.
In this scenario, if both the (original) Master and the Backup (acting as Master) are in operation when the merger occurs, the original Master will reassert its role as active Master for the entire stack. If any configuration elements were changed and applied on the Backup during the time it acted as Master (and forwarded to its connected Members), the Backup and its affected Members will reboot and will be reconfigured by the returning Master before resuming their regular roles.
However, if the original Master switch is disrupted (powered down or in the process of rebooting) when it is reconnected with the active stack, the Backup (acting as Master) will retain its acting Master status to avoid disruption to the functioning stack. The deferring Master will temporarily assume a role as Backup.
If both the Master and Backup are rebooted, all member switches in the stack will also reboot. When the switches resume operation, they will assume their originally configured roles.
If, while the stack is still split, the Backup (acting as Master) is explicitly reconfigured to become a regular Master, then when the split stacks are finally merged, the Master with the lowest MAC address will become the new active Master for the entire stack.
Merging Independent Stacks
If switches from different stacks are linked together in a stack topology without first reconfiguring their roles as recommended, it is possible that more than one switch in the stack might be configured as a Master.
Although all switches which are configured for stacking and joined by stacking links are recognized as potential stack participants by any operational Master switches, they are not brought into operation within the stack until explicitly assigned (or “bound”) to a specific Master switch.
Consider two independent stacks, Stack A and Stack B, which are merged into one stacking topology. The stacks will behave independently until the switches in Stack B are bound to Master A (or vice versa). In this example, once the Stack B switches are bound to Master A, Master A will automatically reconfigure them to operate as Stack A Members, regardless of their original status within Stack B.
However, for purposes of future Backup selection, reconfigured Masters retain their identity as configured Masters, even though they otherwise act as Members. In case the configured Master goes down and the Backup takes over as the new Master, these reconfigured Masters become the new Backup. When the original configured Master of the stack boots up again, it acts as a Member. This is one way to have multiple backups in a stack.
© Copyright Lenovo 2016
Chapter 16: Stacking
279
Backup Switch Selection
An operational stack can have one optional Backup at any given time. Only the Backup specified in the active Master’s configuration is eligible to take over current stack control when the Master is rebooted or fails. The Master automatically synchronizes configuration settings with the specified Backup to facilitate the transfer of control functions.
The Backup retains its status until one of the following occurs:

The Backup setting is deleted or changed using the following commands from the active Master:
RS G8052(config)# no stack backup
‐or‐
RS G8052(config)# stack backup <csnum 1‐8>

A new Master assumes operation as active Master in the stack, and uses its own configured Backup settings.

The active Master is rebooted with the boot configuration set to factory defaults (clearing the Backup setting).
Master Failover
When the Master switch is present, it controls the operation of the stack and pushes configuration information to the other switches in the stack. If the active Master fails, then the designated Backup (if one is defined in the Master’s configuration) becomes the new acting Master and the stack continues to operate normally.
Secondary Backup
When a Backup takes over stack control operations, if any other configured Masters (acting as Member switches) are available within the stack, the Backup will select one as a secondary Backup. The primary Backup automatically reconfigures the secondary Backup and specifies itself (the primary Backup) as the new Backup in case the secondary fails. This prevents the chain of stack control from migrating too far from the original Master and Backup configuration intended by the administrator.
Master Recovery
If the prior Master recovers in a functioning stack where the Backup has assumed stack control, the prior Master does not reassert itself as the stack Master. Instead, the prior Master will assume a role as a secondary Backup to avoid further stack disruption.
Upon stack reboot, the Master and Backup will resume their regular roles.
280
G8052 Application Guide for ENOS 8.4
No Backup
If a Backup is not configured on the active Master, or the specified Backup is not operating, then if the active Master fails, the stack will reboot without an active Master.
When a group of stacked switches are rebooted without an active Master present, the switches are considered to be isolated. All isolated switches in the stack are placed in a WAITING state until a Master appears. During this WAITING period, all the ports, except the management port and stacking ports, of these Member switches are placed into operator‐disabled state. Without the Master, a stack cannot respond correctly to networking events.
Stack Member Identification
Each switch in the stack has two numeric identifiers, as follows: 
Attached Switch Number (asnum)
An asnum is automatically assigned by the Master switch, based on each Member switch’s physical connection in relation to the Master. The asnum is mainly used as an internal ID by the Master switch and is not user‐configurable.

Configured Switch Number (csnum):
The csnum is the logical switch ID assigned by the stack administrator. The csnum is used in most stacking‐related configuration commands and switch information output. It is also used as a port prefix to distinguish the relationship between the ports on different switches in the stack.
It is recommended that asnum 1 and csnum 1 be used for identifying the Master switch. By default, csnum 1 is assigned to the Master. If csnum 1 is not available, the lowest available csnum is assigned to the Master.
© Copyright Lenovo 2016
Chapter 16: Stacking
281
Configuring a Stack
Notes:

When stacking mode is enabled on the switch, the configuration is reset to factory default and the port numbering changes.

When a switch mode is changed from standalone to stack or from stack to standalone, the active and backup configuration will be erased. We recommended that you save the configuration to an external device before changing the switch mode.

There are two distinct software images for the G8052. One supports standalone operation only, and the other supports stacking only.
Configuration Overview
This section provides procedures for creating a stack of switches. The high‐level procedure is as follows: 
Configure the stack settings to be available after the next reboot:

Choose one Master switch for the entire stack.

Configure the same stacking VLAN for all switches in the stack.

Configure the desired stacking interlinks.

Configure a management interface.

Reboot the Master switch.

Configure the stack after the reboot:

Bind Member switches to the Master.

Assign a Backup switch.
These tasks are covered in detail in the following sections.
Best Configuration Practices
The following are guidelines for building an effective switch stack:
282

Always connect the stack switches in a complete ring topology (see Figure 25 on page 284).

Avoid disrupting the stack connections unnecessarily while the stack is in operation.

For enhanced redundancy when creating port LAGs, include ports from different stack members in the LAGs.

Avoid changing the csnum definitions unnecessarily while the stack is in operation.

Avoid rebooting the switches unnecessarily.

When in stacking mode, the highest QoS priority queue is reserved for internal stacking requirements. Therefore, only seven priority queues will be available for regular QoS use.
G8052 Application Guide for ENOS 8.4

Configure only as many QoS levels as necessary. This allows the best use of packet buffers.

Before configuring the stack:

Identify the VLAN to be used as the stacking VLAN. 
Save the current configuration to an external device. The port numbering will change once stacking is enabled. Use the saved configuration to reassign ports/interfaces as per the new port numbering scheme. Once a stack is configured, port numbers are displayed using the csnum to identify the switch, followed by the switch port number. For example: Stacking VLANs
VLAN 4090 is the default VLAN reserved for internal traffic on stacking ports. You can change the VLAN, if required. Note: Do not use VLAN 4090 (or the configured VLAN) for any purpose other than internal stacking traffic. Configuring Each Switch for the Stack
To configure each switch for stacking, connect to each switch via its console or management interface and perform the following steps.
Note: IPv6 is not supported in stacking mode. IP interfaces must use IPv4 addressing for proper stack configuration.
1. On each switch, set the stacking membership mode.
By default, each switch is set to Member mode. However, one switch must be set to Master mode. Use the following command on only the designated Master switch:
RS G8052(config)# boot stack mode master
Note: If any Member switches are incorrectly set to Master mode, use the mode member option to set them back to Member mode.
2. On each switch, configure the stacking VLAN (or use the default setting).
Although any VLAN (except VLAN 1) may be defined for stack traffic, it is highly recommended that the default, VLAN 4090 as shown in the following example, be reserved for stacking.
RS G8052(config)# boot stack vlan 4090
3. On each switch, designate the stacking links.
To create the recommended topology, dedicate at least two 10Gb ports on each switch to stacking. By default, 10Gb Ethernet ports 49 and 50 are used. © Copyright Lenovo 2016
Chapter 16: Stacking
283
Use the following command to specify the links to be used in the stacking LAG:
RS G8052(config)# boot stack higig­trunk <list of port names or aliases>
Note: Ports configured as Server ports for use with VMready cannot be designated as stacking links.
4. On each switch, perform a reboot:
RS G8052(config)# reload
5. Physically connect the stack LAGs.
To create the recommended topology, attach the two designated stacking links in a bidirectional ring. As shown in Figure 25, connect each switch in turn to the next, starting with the Master switch. To complete the ring, connect the last Member switch back to the Master.
Figure 25. Example of Stacking Connections
Master
Switch
Switches
connected in
bidirectional
ring topology
Member
Switch
Member
Switch
Member
Switch
Note: The stacking feature is designed such that the stacking links in a ring topology do not result in broadcast loops. The stacking ring is thus valid (no stacking links are blocked), even when Spanning Tree protocol is enabled.
When two units are connected with multiple stacking links, the links are automatically added as members of a higig LAG.
Once the stack LAGs are connected, the switches will perform low‐level stacking configuration.
Note: Although stack link failover/failback is accomplished on a sub‐second basis, to maintain the best stacking operation and avoid traffic disruption, it is recommended not to disrupt stack links after the stack is formed.
284
G8052 Application Guide for ENOS 8.4
Additional Master Configuration
Once the stack links are connected, complete the configuration.
Configuring an External IPv4 Address for the Stack
In addition to the internal management IP interface assigned to the Master switch, a standard switch IP interface can be used for connecting to and managing the stack externally. Configure an IP interface with the following:

Stack IPv4 address and mask

IPv4 default gateway address

VLAN number used for external access to the stack (rather than the internal VLAN 4090 used for inter‐stack traffic)
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface ip <IP interface number>
G8052(config­ip­if)# ip address <stack IPv4 address>
G8052(config­ip­if)# ip netmask <IPv4 subnet mask>
G8052(config­ip­if)# vlan <VLAN ID>
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
G8052(config)# ip gateway <gateway number> address <gateway IPv4 address>
G8052(config)# ip gateway <gateway number> enable
Once completed, stack management can be performed via Telnet or BBI (if enabled) from any point in the configured VLAN, using the IPv4 address of the configured IP interface.
In the event that the Master switch fails, if a Backup switch is configured (see “Assigning a Stack Backup Switch” on page 287), the external IP interface for the stack will still be available.
Locating an External Stack Interface
If the IPv4 address and VLAN of an external IP interface for the stack is unknown, connect to the Master switch using the serial console and execute the following command:
RS G8052(config)# show interface ip
© Copyright Lenovo 2016
Chapter 16: Stacking
285
Viewing Stack Connections
To view information about the switches in a stack, execute the following command: RS G8052(config)# show stack switch
Stack name: GP_STK
Local switch is the master.
Local switch:
csnum ­ 2
MAC ­ fc:cf:62:9d:4f:00
Switch Type ­ 10 (G8052)
Switch Mode (cfg) ­ Master
Priority ­ 225
Stack MAC ­ fc:cf:62:9d:4f:1f
Master switch:
csnum ­ 2
MAC ­ fc:cf:62:9d:4f:00
Backup switch:
csnum ­ 3
MAC ­ 34:40:b5:3f:0b:00 Configured Switches: ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
csnum MAC asnum ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
C1 34:40:b5:3f:1d:00 A2 C2 fc:cf:62:9d:4f:00 A1 C3 34:40:b5:3f:0b:00 A5 C4 34:40:b5:41:76:00 A4 C5 34:40:b5:40:bc:00 A3 Attached Switches in Stack: ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
asnum MAC csnum State
­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
A1 fc:cf:62:9d:4f:00 C2 IN_STACK
A2 34:40:b5:3f:1d:00 C1 IN_STACK
A3 34:40:b5:40:bc:00 C5 IN_STACK
A4 34:40:b5:41:76:00 C4 IN_STACK
A5 34:40:b5:3f:0b:00 C3 IN_STACK
RS G8052(config)#
RS G8052(config)# show stack attached­switches
Attached Switches in Stack: ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
asnum MAC csnum State
­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
A1 74:99:75:d1:fc:00 C1 IN_STACK A2 74:99:75:d0:99:00 C2 IN_STACK A3 74:99:75:d1:e9:00 C3 IN_STACK RS G8052(config)#
286
G8052 Application Guide for ENOS 8.4
Binding Members to the Stack
You can bind Member switches to a stack csnum using either their asnum or MAC address :
RS G8052(config)# stack switch­number <csnum> mac <MAC address>
‐or‐
RS G8052(config)# stack switch­number <csnum> bind <asnum>
To remove a Member switch, execute the following command:
RS G8052(config)# no stack switch­number <csnum>
To bind all units of a stack, use the command:
RS G8052(config)# stack bind
The stack bind command automatically assigns switch numbers to all attached switches in the stack that do not yet have a number assigned.
Assigning a Stack Backup Switch
To define a Member switch as a Backup (optional) which will assume the Master role if the Master switch fails, execute the following command:
RS G8052(config)# stack backup <csnum>
© Copyright Lenovo 2016
Chapter 16: Stacking
287
Managing the Stack
The stack is managed primarily through the Master switch. The Master switch then pushes configuration changes and run‐time information to the Member switches. Accessing the Master Switch CLI
To access the Master switch, use Telnet or the Browser‐Based Interface (BBI) as follows: 
Use the serial console.

On any switch in the stack, connect to any port that is not part of an active LAG and is a member of a VLAN. To access the stack, use the IP address of any IP interface that is member of the VLAN.
Rebooting Stacked Switches via the Master
Rebooting Stacked Switches using the ISCLI
The administrator can reboot individual switches in the stack, or the entire stack using the following commands:
(Reboot all switches in the stack)
(Reboot only the stack Master)
RS G8052(config)# reload switch <csnum list>(Reboot only the listed switches)
RS G8052(config)# reload
RS G8052(config)# reload master
Rebooting Stacked Switches using the BBI
The Configure > System > Config/Image Control window allows the administrator to perform a reboot of individual switches in the stack, or the entire stack. The following table describes the stacking Reboot buttons. Table 25. Stacking Boot Management buttons
Field
Description
Reboot Stack
Performs a software reboot/reset of all switches in the stack. The software image specified in the Image To Boot drop‐down list becomes the active image. Reboot Master
Performs a software reboot/reset of the Master switch. The software image specified in the Image To Boot drop‐down list becomes the active image. Reboot Switches Performs a reboot/reset on selected switches in the stack. Select one or more switches in the drop‐down list, and click Reboot Switches. The software image specified in the Image To Boot drop‐down list becomes the active image. The Update Image/Cfg section of the window applies to the Master. When a new software image or configuration file is loaded, the file first loads onto the Master, and the Master pushes the file to all other switches in the stack, placing it in the 288
G8052 Application Guide for ENOS 8.4
same software or configuration bank as that on the Master. For example, if the new image is loaded into image 1 on the Master switch, the Master will push the same firmware to image 1 on each Member switch.
© Copyright Lenovo 2016
Chapter 16: Stacking
289
Upgrading Software in an Existing Stack
Upgrade all stacked switches at the same time. The Master controls the upgrade process. Use the following procedure to perform a software upgrade for a stacked system. 1. Load new software on the Master (see “Loading New Software to Your Switch” on page 76). The Master pushes the new software image to all Members in the stack, as follows:

If the new software is loaded into image 1, the Master pushes the software into image 1 on all Members. 
If loaded into image 2, the Master pushes the software into image 2 on all Members. The software push can take several minutes to complete. 2. Verify that the software push is complete. Use either the BBI or the ISCLI:

From the BBI, go to Dashboard > Stacking > Push Status and view the Image Push Status Information, or

From the ISCLI, use following command to verify the software push:
RS G8052(config)# show stack push­status
Image 1 transfer status info:
Switch 00:16:60:f9:33:00:
last receive successful
Switch 00:17:ef:c3:fb:00:
not received ­ file not sent or transfer in progress
Image 2 transfer status info:
Switch 00:16:60:f9:33:00:
last receive successful
Switch 00:17:ef:c3:fb:00:
last receive successful
Boot image transfer status info:
Switch 00:16:60:f9:33:00:
last receive successful
Switch 00:17:ef:c3:fb:00:
last receive successful
Config file transfer status info:
Switch 00:16:60:f9:33:00:
last receive successful
Switch 00:17:ef:c3:fb:00:
last receive successful
3. Reboot all switches in the stack. Use either the ISCLI or the BBI.

From the BBI, select Configure > System > Config/Image Control. Click Reboot Stack.

From the ISCLI, use the following command:
RS G8052(config)# reload
290
G8052 Application Guide for ENOS 8.4
4. Once the switches in the stack have rebooted, verify that all of them are using the same version of firmware. Use either the ISCLI or the BBI.

From the BBI, open Dashboard > Stacking > Stack Switches and view the Switch Firmware Versions Information from the Attached Switches in Stack.

From the ISCLI, use the following command:
RS G8052(config)# show stack version
Switch Firmware Versions: ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
asnum csnum MAC S/W Version Serial # ­­­­­ ­­­­­ ­­­­­ ­­­­­­ ­­­­­­­­­­ ­­­­­­­­­­­­ A1 C2 fc:cf:62:9d:4f:00 image1 8.4.0.1 US7042001C A2 C1 34:40:b5:3f:1d:00 image1 8.4.0.1 Y250VT215167 A3 C5 34:40:b5:40:bc:00 image1 8.4.0.1 Y250VT21S410 A4 C4 34:40:b5:41:76:00 image1 8.4.0.1 Y250VT21S409 A5 C3 34:40:b5:3f:0b:00 image1 8.4.0.1 Y250VT215168
© Copyright Lenovo 2016
Chapter 16: Stacking
291
Replacing or Removing Stacked Switches
Stack switches may be replaced or removed while the stack is in operation. However, the following conditions must be met to avoid unnecessary disruption:

If removing an active Master switch, make sure that a valid Backup exists in the stack.

It is best to replace only one switch at a time.

If replacing or removing multiple switches in a ring topology, when one switch has been properly disconnected (see the procedures that follow), any adjacent switch can also be removed.

Removing any two, non‐adjacent switches in a ring topology will divide the ring and disrupt the stack.
Use the following procedures to replace a stack switch.
Removing a Switch from the Stack
1. Make sure the stack is configured in a ring topology.
Note: When an open‐ended daisy‐chain topology is in effect (either by design or as the result of any failure of one of the stacking links in a ring topology), removing a stack switch from the interior of the chain can divide the chain and cause serious disruption to the stack operation.
2. If removing a Master switch, make sure that a Backup switch exists in the stack, then turn off the Master switch.
This will force the Backup switch to assume Master operations for the stack.
3. Remove the stack link cables from the old switch only.
4. Disconnect all network cables from the old switch only.
5. Remove the old switch.
Installing the New Switch or Healing the Topology
If using a ring topology, but not installing a new switch for the one removed, close the ring by connecting the open stack links together, essentially bypassing the removed switch.
Otherwise, if replacing the removed switch with a new unit, use the following procedure:
1. Make sure the new switch meets the stacking requirements on page 276.
2. Place the new switch in its determined place according to the RackSwitch G8052 Installation Guide.
3. Connect to the ISCLI of the new switch (not the stack interface).
4. Set the stacking mode.
292
G8052 Application Guide for ENOS 8.4
By default, each switch is set to Member mode. However, if the incoming switch has been used in another stacking configuration, it may be necessary to ensure the proper mode is set.

If replacing a Member or Backup switch:
RS G8052(config)# boot stack mode member

If replacing a Master switch:
RS G8052(config)# boot stack mode master
5. Configure the stacking VLAN on the new switch, or use the default setting.
Although any VLAN may be defined for stack traffic, it is highly recommended that the default, VLAN 4090, be reserved for stacking, as shown in the following command.
RS G8052(config)# boot stack vlan 4090
6. Designate the stacking links.
It is recommended that you designate the same number of 10Gb ports for stacking as the switch being replaced. By default, 10Gb Ethernet ports 49 and 50 are used. At least one 10Gb port is required. Use the following command to specify the links to be used in the stacking LAG:
RS G8052(config)# boot stack higig­trunk <list of port names or aliases>
7. Attach the required stack link cables to the designated stack links on the new switch.
8. Attach the desired network cables to the new switch.
9. Reboot the new switch:
RS G8052(config)# reload
When the new switch boots, it will join the existing stack. Wait for this process to complete.
© Copyright Lenovo 2016
Chapter 16: Stacking
293
Binding the New Switch to the Stack
1. Log in to the stack interface.
Note: If replacing the Master switch, be sure to log in to the stack interface (hosted temporarily on the Backup switch) rather than logging in directly to the newly installed Master.
2. From the stack interface, assign the csnum for the new switch.
You can bind Member switches to a stack csnum using either the new switch’s asnum or MAC address :
RS G8052(config)# stack switch­number <csnum> mac <MAC address>
‐or‐
RS G8052(config)# stack switch­number <csnum> bind <asnum>
Note: If replacing the Master switch, the Master will not assume control from the Backup unless the Backup is rebooted or fails.
Performing a Rolling Reload or Upgrade
You can perform a sequential reload or upgrade, otherwise known as a staggered or rolling reload or upgrade, to avoid the need for an overall outage. With a rolling reload or upgrade, some of the hardware stays up at all times. This approach differs from the traditional image upgrade that requires manual image downloads and install to individual switches, which then requires the entire logical switch reboot.
After the firmware is copied to all members of the stack, the rolling reload or upgrade process automatically reboots all switches sequentially in the following order:

Backup switch

Master switch

Other stack members, from lowest to highest csnum
During the rolling firmware reload or upgrade process, there will be continuous connectivity to the upstream network. From the point of view of the stack, it is as though a series of switch and uplink failures are occurring. When the design is cabled and configured properly, the environment redirects traffic.
For detailed instructions on upgrading and rebooting, see Chapter 3, “Switch Software Management.”
Starting a Rolling Reload
To start a rolling reload, use the command:
RS G8052(config)# reload staggered [delay <minutes>]
where delay is an integer from 2 to 20 representing the time delay in minutes between switch reboots. The default value is one minute between switch reboots.
294
G8052 Application Guide for ENOS 8.4
Starting a Rolling Upgrade
To start a rolling upgrade, use the command:
RS G8052(config)# copy {tftp|ftp|sftp} {image1|image2} {address <IP address>} {filename <image filename>} staggered­upgrade [delay <minutes>]
where:

tftp, ftp, sftp
is the protocol for copying

image1, image2
is the image to which the firmware is being copied

address
is the IP address from which the firmware is being copied

delay
is the delay between each reload, in minutes
To upgrade both the boot and the firmware images:
1. Load the boot image with a non‐staggered copy:
RS G8052(config)# copy {tftp|ftp|sftp} boot­image {address <IP address>} {filename <image filename>}
2. Load the firmware image with a staggered copy:
RS G8052(config)# copy {tftp|ftp|sftp} {image1|image2} {address <IP address>} {filename <image filename>} staggered­upgrade [delay <minutes>]
© Copyright Lenovo 2016
Chapter 16: Stacking
295
Saving Syslog Messages
By default, syslog messages on each member of a stack are saved to flash memory on that stack member. You may want to preserve stacking‐related errors. To accomplish this, in console mode, use the following command
RS G8052(config)# [no] logging log stacking
The master switch can display the syslog messages originated on any stack member as long as the specified stack element is currently an active member of the stack using the command:
RS G8052(config)# show logging [swn <configured‐switch‐number>] [{messages | reverse | severity <0‐7>}]
where:
<configured‐switch‐number>
The configured switch number. If no number is supplied, the command applies to the master switch.
messages
show last 2000 syslog messages
reverse
show syslog information in reverse priority order
severity <0‐7>
show messages of a specific severity level
For example, to retrieve the last 2000 syslog messages of severity 4 or greater from switch 3, enter:
RS G8052(config)# show logging swn 3 severity 4
To retrieve the contents of the log files stored on flash on a specified switch in the stack and copy that information to an external host using the specified protocol (SFTP or TFTP). In case the feature of saving log to flash is disabled, this command must be rejected.
To copy syslog content to an external host using SFTP or TFTP, use the command:
RS G8052(config)# copy log {swn <switch number>] stfp | {tftp [address <address>] [filename <file>]
where:
296
<switch number>
The configured switch number. If no number is supplied, the command applies to the master switch.
address
The IP address of the TFTP host
file
The filename on the TFTP host
G8052 Application Guide for ENOS 8.4
For example:
RS G8052(config)# copy log tftp 192.168.1.85 // Copy logs from clients on the master
RS G8052(config)# copy log swn 3 tftp 10.10.10.1 // Copy logs from stack member 3
To configure up to two external hosts to log stack errors, use the command:
RS G8052(config)# logging host <host instance> {address <address> | facility <facility> | severity <severity>
where
<host instance>
the host instance; either 1 or 2.
<address>
the IP address of the host being logged
<facility>
the facility (0‐7) of the logs being written to external syslog servers
<severity>
the severity (0‐7) of the logs being written to external syslog servers
To enable console output of syslog messages, use the command: RS G8052(config)# logging console severity <severity>
where <severity> configures the severity of logs to be sent to the console.
To configure the severity of syslogs written to flash, use the command:
RS G8052(config)# logging buffer severity <severity>
where <severity> configures the severity of logs to be written to flash.
© Copyright Lenovo 2016
Chapter 16: Stacking
297
ISCLI Stacking Commands
Stacking‐related ISCLI commands are listed here. For details on specific commands, see the RackSwitch G8052 ISCLI Command Reference Guide.
boot stack higig­trunk <port list>
boot stack mode {master|member} [<asnum>|master|backup|all]
 boot stack push­image {boot­image|image1|image2} <asnum>
 boot stack vlan <VLAN>



copy log [swn <switch number>] stfp

copy log [swn <switch number>] tftp address <address> filename <file>

default boot stack {<asnum>|master|backup|all}
logging buffer severity <severity>
logging console severity <severity>
logging host <host instance> {address <address> | facility <facility> | severity <severity>
[no] logging log stacking
no stack backup
no stack name
no stack switch­number <csnum>
show boot stack [<asnum>|master|backup|all]









show logging [swn <configured‐switch‐number>] [ { messages | reverse | severity <0‐7>}]

show stack attached­switches
show stack backup
show stack dynamic
show stack link
show stack name
show stack path­map [<csnum>]
show stack push­status
show stack switch
show stack switch­number [<csnum>]
show stack version
stack backup <csnum>
stack name <word>
stack switch­number <csnum> bind <asnum>
stack switch­number <csnum> mac <MAC address>













298
G8052 Application Guide for ENOS 8.4
Chapter 17. VMready
Virtualization is used to allocate server resources based on logical needs, rather than on strict physical structure. With appropriate hardware and software support, servers can be virtualized to host multiple instances of operating systems, known as virtual machines (VMs). Each VM has its own presence on the network and runs its own service applications.
Software known as a hypervisor manages the various virtual entities (VEs) that reside on the host server: VMs, virtual switches, and so on. Depending on the virtualization solution, a virtualization management server may be used to configure and manage multiple hypervisors across the network. With some solutions, VMs can even migrate between host hypervisors, moving to different physical hosts while maintaining their virtual identity and services.
The Lenovo Enterprise Network Operating System 8.4 VMready feature supports up to 1024 VEs in a virtualized data center environment. The switch automatically discovers the VEs attached to switch ports, and distinguishes between regular VMs, Service Console Interfaces, and Kernel/Management Interfaces in a VMware® environment.
VEs may be placed into VM groups on the switch to define communication boundaries: VEs in the same VM group may communicate with each other, while VEs in different groups may not. VM groups also allow for configuring group‐level settings such as virtualization policies and ACLs.
The administrator can also pre‐provision VEs by adding their MAC addresses (or their IPv4 address or VM name in a VMware environment) to a VM group. When a VE with a pre‐provisioned MAC address becomes connected to the switch, the switch will automatically apply the appropriate group membership configuration.
The G8052 with VMready also detects the migration of VEs across different hypervisors. As VEs move, the G8052 NMotion™ feature automatically moves the appropriate network configuration as well. NMotion gives the switch the ability to maintain assigned group membership and associated policies, even when a VE moves to a different port on the switch.
VMready also works with VMware Virtual Center (vCenter) management software. Connecting with a vCenter allows the G8052 to collect information about more distant VEs, synchronize switch and VE configuration, and extend migration properties.
© Copyright Lenovo 2016
299
VE Capacity
When VMready is enabled, the switch will automatically discover VEs that reside in hypervisors directly connected on the switch ports. Enterprise NOS 8.4 supports up to 1024 VEs. Once this limit is reached, the switch will reject additional VEs.
Note: In rare situations, the switch may reject new VEs prior to reaching the supported limit. This can occur when the internal hash corresponding to the new VE is already in use. If this occurs, change the MAC address of the VE and retry the operation. The MAC address can usually be changed from the virtualization management server console (such as the VMware Virtual Center).
Defining Server Ports
Before you configure VMready features, you must first define whether ports are connected to servers or are used as uplink ports. Use the following ISCLI configuration command to define a port as a server port: RS G8052(config)# system server­ports port <port alias or number>
Ports that are not defined as server ports are automatically considered uplink ports.
VM Group Types
VEs, as well as switch server ports, switch uplink ports, static LAGs, and LACP LAGs, can be placed into VM groups on the switch to define virtual communication boundaries. Elements in a given VM group are permitted to communicate with each other, while those in different groups are not. The elements within a VM group automatically share certain group‐level settings.
ENOS 8.4 supports up to 1024 VM groups. There are two different types:
Local VM groups are maintained locally on the switch. Their configuration is not synchronized with hypervisors.
 Distributed VM groups are automatically synchronized with a virtualization management server (see “Assigning a vCenter” on page 310).

Each VM group type is covered in detail in the following sections.
300
G8052 Application Guide for ENOS 8.4
Local VM Groups
The configuration for local VM groups is maintained on the switch (locally) and is not directly synchronized with hypervisors. Local VM groups may include only local elements: local switch ports and LAGs, and only those VEs connected to one of the switch ports or pre‐provisioned on the switch.
Local VM groups support limited VE migration: as VMs and other VEs move to different hypervisors connected to different ports on the switch, the configuration of their group identity and features moves with them. However, VE migration to and from more distant hypervisors (those not connected to the G8052, may require manual configuration when using local VM groups.
Configuring a Local VM Group
Use the following ISCLI configuration commands to assign group properties and membership:
RS G8052(config)# virt vmgroup <VM group number> ?
cpu
(Enable sending unregistered IPMC to CPU)
flood
(Enable flooding unregistered IPMC)
key <LACP LAG key>
(Add LACP LAG to group)
optflood
(Enable optimized flooding)
port <port alias or number>
(Add port member to group)
portchannel <LAG number>
(Add static LAG to group)
profile <profile name>
(Not used for local groups)
stg <Spanning Tree group>
(Add STG to group)
tag
(Set VLAN tagging on ports)
validate <advanced|basic>
(Validate mode for the group)
vlan <VLAN number>
(Specify the group VLAN)
vm <MAC>|<index>|<UUID>|<IPv4 address>|<name>(Add VM member to group)
vmap <VMAP number> [intports|extports](Specify VMAP number)
© Copyright Lenovo 2016
Chapter 17: VMready
301
The following rules apply to the local VM group configuration commands:

cpu: Enable sending unregistered IPMC to CPU.

flood: Enable flooding unregistered IPMC.

key: Add LACP LAGs to the group.

optflood: Enable optimized flooding to allow sending unregistered IPMC to the Mrouter ports without having any packet loss during the learning period; This option is disabled by default; When optflood is enabled, the flood and cpu settings are ignored.

port: Add switch server ports or switch uplink ports to the group.

portchannel: Add static port LAGs to the group.

profile: The profile options are not applicable to local VM groups. Only distributed VM groups may use VM profiles (see “VM Profiles” on page 303).

stg: The group may be assigned to a Spanning‐Tree group for broadcast loop control (see Chapter 11, “Spanning Tree Protocols”).

tag: Enable VLAN tagging for the VM group. If the VM group contains ports which also exist in other VM groups, enable tagging in both VM groups.

validate: Set validation mode for the group.

vlan: Each VM group must have a unique VLAN number. This is required for local VM groups. If one is not explicitly configured, the switch will automatically assign the next unconfigured VLAN when a VE or port is added to the VM group.

vmap: Each VM group may optionally be assigned a VLAN‐based ACL (see “VLAN Maps” on page 314).

vm: Add VMs.
VMs and other VEs are primarily specified by MAC address. They can also be specified by UUID, IP address, or by the index number as shown in various VMready information output (see “VMready Information Displays” on page 317).
Use the no variant of the commands to remove or disable VM group configuration settings:
RS G8052(config)# no virt vmgroup <VM group number> [?]
302
G8052 Application Guide for ENOS 8.4
Distributed VM Groups
Distributed VM groups allow configuration profiles to be synchronized between the G8052 and associated hypervisors and VEs. This allows VE configuration to be centralized, and provides for more reliable VE migration across hypervisors.
Using distributed VM groups requires a virtualization management server. The management server acts as a central point of access to configure and maintain multiple hypervisors and their VEs (VMs, virtual switches, and so on).
The G8052 must connect to a virtualization management server before distributed VM groups can be used. The switch uses this connection to collect configuration information about associated VEs, and can also automatically push configuration profiles to the virtualization management server, which in turn configures the hypervisors and VEs. See “Virtualization Management Servers” on page 310 for more information.
VM Profiles
VM profiles are required for configuring distributed VM groups. They are not used with local VM groups. A VM profile defines the VLAN and virtual switch bandwidth shaping characteristics for the distributed VM group. The switch distributes these settings to the virtualization management server, which in turn distributes them to the appropriate hypervisors for VE members associated with the group.
Creating VM profiles is a two part process. First, the VM profile is created as shown in the following command on the switch:
RS G8052(config)# virt vmprofile <profile name>
Next, the profile must be edited and configured using the following configuration commands:
RS G8052(config)# virt vmprofile edit <profile name> ?
eshaping <average bandwidth> <burst size> <peak>
shaping <average bandwidth> <burst size> <peak>
vlan <VLAN number>
For virtual switch bandwidth shaping parameters, average and peak bandwidth are specified in kilobits per second (a value of 1000 represents 1 Mbps). Burst size is specified in kilobytes (a value of 1000 represents 1 MB). Eshaping (egress shaping) is used for distributed virtual switch.
Note: The bandwidth shaping parameters in the VM profile are used by the hypervisor virtual switch software. To set bandwidth policies for individual VEs, see “VM Policy Bandwidth Control” on page 315.
Once configured, the VM profile may be assigned to a distributed VM group as shown in the following section.
© Copyright Lenovo 2016
Chapter 17: VMready
303
Initializing a Distributed VM Group
Note: A VM profile is required before a distributed VM group may be configured. See “VM Profiles” on page 303 for details.
Once a VM profile is available, a distributed VM group may be initialized using the following configuration command:
RS G8052(config)# virt vmgroup <VM group number> profile <VM profile name>
Only one VM profile can be assigned to a given distributed VM group. To change the VM profile, the old one must first be removed using the following ISCLI configuration command:
RS G8052(config)# no virt vmgroup <VM group number> profile
Note: The VM profile can be added only to an empty VM group (one that has no VLAN, VMs, or port members). Any VM group number currently configured for a local VM group (see “Local VM Groups” on page 301) cannot be converted and must be deleted before it can be used for a distributed VM group.
Assigning Members
VMs, ports, and LAGs may be added to the distributed VM group only after the VM profile is assigned. Group members are added, pre‐provisioned, or removed from distributed VM groups in the same manner as with local VM groups (“Local VM Groups” on page 301), with the following exceptions:
304

VMs: VMs and other VEs are not required to be local. Any VE known by the virtualization management server can be part of a distributed VM group.

The VM group vlan option (see page 302) cannot be used with distributed VM groups. For distributed VM groups, the VLAN is assigned in the VM profile.
G8052 Application Guide for ENOS 8.4
Synchronizing the Configuration
When the configuration for a distributed VM group is modified, the switch updates the assigned virtualization management server. The management server then distributes changes to the appropriate hypervisors.
For VM membership changes, hypervisors modify their internal virtual switch port groups, adding or removing server port memberships to enforce the boundaries defined by the distributed VM groups. Virtual switch port groups created in this fashion can be identified in the virtual management server by the name of the VM profile, formatted as follows: Lenovo_<VM profile name>
(or)
Lenovo_<VM profile name> <index number>
(for vDS)
Adding a server host interface to a distributed VM group does not create a new port group on the virtual switch or move the host. Instead, because the host interface already has its own virtual switch port group on the hypervisor, the VM profile settings are applied to its existing port group.
Note: When applying the distributed VM group configuration, the virtualization management server and associated hypervisors must take appropriate actions. If a hypervisor is unable to make requested changes, an error message will be displayed on the switch. Be sure to evaluate all error message and take the appropriate actions for the expected changes to apply.
Removing Member VEs
Removing a VE from a distributed VM group on the switch will have the following effects on the hypervisor:
© Copyright Lenovo 2016

The VE will be moved to the Lenovo_Default port group in VLAN 0 (zero).

Traffic shaping will be disabled for the VE.

All other properties will be reset to default values inherited from the virtual switch.
Chapter 17: VMready
305
VMcheck
The G8052 primarily identifies virtual machines by their MAC addresses. An untrusted server or a VM could identify itself by a trusted MAC address leading to MAC spoofing attacks. Sometimes, MAC addresses get transferred to another VM, or they get duplicated.
The VMcheck solution addresses these security concerns by validating the MAC addresses assigned to VMs. The switch periodically sends hello messages on server ports. These messages include the switch identifier and port number. The hypervisor listens to these messages on physical NICs and stores the information, which can be retrieved using the VMware Infrastructure Application Programming Interface (VI API). This information is used to validate VM MAC addresses. Two modes of validation are available: Basic and Advanced.
Use the following command to select the validation mode or to disable validation: RS G8052(config)# [no] virt vmgroup <VM group number> validate {basic|advanced}
Basic Validation
This mode provides port‐based validation by identifying the port used by a hypervisor. It is suitable for environments in which MAC reassignment or duplication cannot occur.
The switch, using the hello message information, identifies a hypervisor port. If the hypervisor port is found in the hello message information, it is deemed to be a trusted port. Basic validation should be enabled when:

A VM is added to a VM group, and the MAC address of the VM interface is in the Layer 2 table of the switch.

A VM interface that belongs to a VM group experiences a “source miss” i.e. is not able to learn new MAC address.

A trusted port goes down. Port validation must be performed to ensure that the port does not get connected to an untrusted source when it comes back up.
Use the following command to set the action to be performed if the switch is unable to validate the VM MAC address: RS G8052(config)# virt vmcheck action basic {log|link}
log ­ generates a log
link ­ disables the port
306
G8052 Application Guide for ENOS 8.4
Advanced Validation
This mode provides VM‐based validation by mapping a switch port to a VM MAC address. It is suitable for environments in which spoofing, MAC reassignment, or MAC duplication is possible.
When the switch receives frames from a VM, it first validates the VM interface based on the VM MAC address, VM Universally Unique Identifier (UUID), Switch port, and Switch ID available in the hello message information. Only if all the four parameters are matched, the VM MAC address is considered valid.
In advanced validation mode, if the VM MAC address validation fails, an ACL can be automatically created to drop the traffic received from the VM MAC address on the switch port. Use the following command to specify the number of ACLs to be automatically created for dropping traffic: RS G8052(config)# virt vmcheck acls max <1‐640>
Use the following command to set the action to be performed if the switch is unable to validate the VM MAC address: RS G8052(config)# virt vmcheck action advanced {log|link|acl}
Following are the other VMcheck commands: Table 26. VMcheck Commands
© Copyright Lenovo 2016
Command
Description
RS G8052(config)# virt vmware hello {ena|
hport <port number>|haddr|htimer}
Hello messages setting: enable/add port/advertise this IP address in the hello messages instead of the default management IP address/set the timer to send the hello messages
RS G8052(config)# no virt vmware hello {enable|hport <port number>}
Disable hello mes‐
sages/remove port
RS G8052(config)# [no] virt vmcheck trust <port number or range>
Mark a port as trusted; Use the no form of the command to mark port as untrusted
RS G8052# no virt vmcheck acls
ACLs cannot be used for VMcheck
Chapter 17: VMready
307
Virtual Distributed Switch
A virtual Distributed Switch (vDS ) allows the hypervisor’s NIC to be attached to the vDS instead of its own virtual switch. The vDS connects to the vCenter and spans across multiple hypervisors in a datacenter. The administrator can manage virtual machine networking for the entire data center from a single interface. The vDS enables centralized provisioning and administration of virtual machine networking in the data center using the VMware vCenter server.
When a member is added to a distributed VM group, a distributed port group is created on the vDS. The member is then added to the distributed port group. Distributed port groups on a vDS are available to all hypervisors that are connected to the vDS. Members of a single distributed port group can communicate with each other.
Note: vDS works with ESX 4.0 or higher versions.
To add a vDS, use the command: RS G8052# virt vmware dvswitch add <datacenter name> <dvSwitch name> [<dvSwitch‐version>]
Prerequisites
Before adding a vDS on the G8052, ensure the following:
VMware vCenter is fully installed and configured and includes a “bladevm” administration account and a valid SSL certificate.
 A virtual distributed switch instance has been created on the vCenter. The vDS version must be higher or the same as the hypervisor version on the hosts.
 At least two hypervisors are configured. 
Guidelines
Before migrating VMs to a vDS, consider the following:

At any one time, a VM NIC can be associated with only one virtual switch: to the hypervisor’s virtual switch, or to the vDS.

Management connection to the server must be ensured during the migration. The connection is via the Service Console or the Kernel/Management Interface.

The vDS configuration and migration can be viewed in vCenter at the following locations:

vDS: Home> Inventory > Networking

vDS Hosts: Home > Inventory > Networking > vDS > Hosts
Note: These changes will not be displayed in the running configuration on the G8052. 308
G8052 Application Guide for ENOS 8.4
Migrating to vDS
You can migrate VMs to the vDS using vCenter. The migration may also be accomplished using the operational commands on the G8052 available in the following CLI menus: For VMware vDS operations: RS G8052# virt vmware dvswitch ?
add Add a dvSwitch to a DataCenter
addhost Add a host to a dvSwitch
adduplnk Add a physical NIC to dvSwitch uplink ports
del Remove a dvSwitch from a DataCenter
remhost Remove a host from a dvSwitch
remuplnk Remove a physical NIC from dvSwitch uplink ports
For VMware distributed port group operations: RS G8052# virt vmware dpg ?
add Add a port group to a dvSwitch
del Delete a port group from a dvSwitch
update Update a port group on a dvSwitch
vmac Change a VM NIC's port group
© Copyright Lenovo 2016
Chapter 17: VMready
309
Virtualization Management Servers
The G8052 can connect with a virtualization management server to collect configuration information about associated VEs. The switch can also automatically push VM group configuration profiles to the virtualization management server, which in turn configures the hypervisors and VEs, providing enhanced VE mobility.
One virtual management server must be assigned on the switch before distributed VM groups may be used. ENOS 8.4 currently supports only the VMware Virtual Center (vCenter).
Assigning a vCenter
Assigning a vCenter to the switch requires the following:
The vCenter must have a valid IPv4 address which is accessible to the switch (IPv6 addressing is not supported for the vCenter).
 A user account must be configured on the vCenter to provide access for the switch. The account must have (at a minimum) the following vCenter user privi‐
leges:
 Network
 Host Network > Configuration
 Virtual Machine > Modify Device Settings

Once vCenter requirements are met, the following configuration command can be used on the G8052 to associate the vCenter with the switch:
RS G8052(config)# virt vmware vcspec <vCenter IPv4 address> <username> [noauth]
This command specifies the IPv4 address and account username that the switch will use for vCenter access. Once entered, the administrator will be prompted to enter the password for the specified vCenter account.
The noauth option causes to the switch to ignores SSL certificate authentication. This is required when no authoritative SSL certificate is installed on the vCenter.
Note: By default, the vCenter includes only a self‐signed SSL certificate. If using the default certificate, the noauth option is required.
Once the vCenter configuration has been applied on the switch, the G8052 will connect to the vCenter to collect VE information.
310
G8052 Application Guide for ENOS 8.4
vCenter Scans
Once the vCenter is assigned, the switch will periodically scan the vCenter to collect basic information about all the VEs in the datacenter, and more detailed information about the local VEs that the switch has discovered attached to its own ports.
The switch completes a vCenter scan approximately every two minutes. Any major changes made through the vCenter may take up to two minutes to be reflected on the switch. However, you can force an immediate scan of the vCenter by using one of the following ISCLI privileged EXEC commands:
RS G8052# virt vmware scan
(Scan the vCenter)
‐or‐
RS G8052# show virt vm ­v ­r
(Scan vCenter and display result)
Deleting the vCenter
To detach the vCenter from the switch, use the following configuration command:
RS G8052(config)# no virt vmware vcspec
Note: Without a valid vCenter assigned on the switch, any VE configuration changes must be manually synchronized.
Deleting the assigned vCenter prevents synchronizing the configuration between the G8052 and VEs. VEs already operating in distributed VM groups will continue to function as configured, but any changes made to any VM profile or distributed VM group on the switch will affect only switch operation; changes on the switch will not be reflected in the vCenter or on the VEs. Likewise, any changes made to VE configuration on the vCenter will no longer be reflected on the switch.
© Copyright Lenovo 2016
Chapter 17: VMready
311
Exporting Profiles
VM profiles for discovered VEs in distributed VM groups are automatically synchronized with the virtual management server and the appropriate hypervisors. However, VM profiles can also be manually exported to specific hosts before individual VEs are defined on them.
By exporting VM profiles to a specific host, virtual machine port groups will be available to the host’s internal virtual switches so that new VMs may be configured to use them.
VM migration requires that the target hypervisor includes all the virtual switch port groups to which the VM connects on the source hypervisor. The VM profile export feature can be used to distribute the associated port groups to all the potential hosts for a given VM.
A VM profile can be exported to a host using the following ISCLI privileged EXEC command:
RS G8052# virt vmware export <VM profile name> <host list> <virtual switch name>
The host list can include one or more target hosts, specified by host name, IPv4 address, or UUID, with each list item separated by a space.
Once executed, the requisite port group will be created on the specified virtual switch. If the specified virtual switch does not exist on the target host, the port group will not be created.
VMware Operational Commands
The G8052 may be used as a central point of configuration for VMware virtual switches and port groups using the following ISCLI privileged EXEC commands:
RS G8052# virt vmware ?
dpg
Distributed port group operations
dvswitch VMWare dvSwitch operations export
Create or update a vm profile on one host
pg
Add a port group to a host
scan
Perform a VM Agent scan operation now
updpg
Update a port group on a host
vmacpg
Change a vnic's port group
vsw
Add a vswitch to a host
312
G8052 Application Guide for ENOS 8.4
Pre-Provisioning VEs
VEs may be manually added to VM groups in advance of being detected on the switch ports. By pre‐provisioning the MAC address of VEs that are not yet active, the switch will be able to later recognize the VE when it becomes active on a switch port, and immediately assign the proper VM group properties without further configuration.
Undiscovered VEs are added to or removed from VM groups using the following configuration commands:
RS G8052(config)# [no] virt vmgroup <VM group number> vm <VE MAC address>
For the pre‐provisioning of undiscovered VEs, a MAC address is required. Other identifying properties, such as IPv4 address or VM name permitted for known VEs, cannot be used for pre‐provisioning.
© Copyright Lenovo 2016
Chapter 17: VMready
313
VLAN Maps
A VLAN map (VMAP) is a type of Access Control List (ACL) that is applied to a VLAN or VM group rather than to a switch port as with regular ACLs (see Chapter 7, “Access Control Lists”). In a virtualized environment, VMAPs allow you to create traffic filtering and metering policies that are associated with a VM group VLAN, allowing filters to follow VMs as they migrate between hypervisors.
ENOS 8.4 supports up to 128 VMAPs. Individual VMAP filters are configured in the same fashion as regular ACLs, except that VLANs cannot be specified as a filtering criteria (unnecessary, since VMAPs are assigned to a specific VLAN or associated with a VM group VLAN).
VMAPs are configured using the following ISCLI configuration command path:
RS G8052(config)# access­control vmap <VMAP ID> ?
action Set filter action
egress­port Set to filter for packets egressing this port
ethernet Ethernet header options
ipv4 IP version 4 header options
meter ACL metering configuration
mirror Mirror options
packet­format Set to filter specific packet format types
re­mark ACL re­mark configuration
statistics Enable access control list statistics
tcp­udp TCP and UDP filtering options
Once a VMAP filter is created, it can be assigned or removed using the following commands:

For regular VLANs, use config‐vlan mode:
RS G8052(config)# vlan <VLAN ID>
RS G8052(config­vlan)# [no] vmap <VMAP ID> [serverports| non­serverports]

For a VM group, use the global configuration mode:
RS G8052(config)# [no] virt vmgroup <ID> vmap <VMAP ID> [serverports|non­serverports]
Note: Each VMAP can be assigned to only one VLAN or VM group. However, each VLAN or VM group may have multiple VMAPs assigned to it.
The optional serverports or non­serverports parameter can be specified to apply the action (to add or remove the VMAP) for either the switch server ports (serverports) or switch uplink ports (non­serverports). If omitted, the operation will be applied to all ports in the associated VLAN or VM group.
Note: VMAPs have a lower priority than port‐based ACLs. If both an ACL and a VMAP match a particular packet, both filter actions will be applied as long as there is no conflict. In the event of a conflict, the port ACL will take priority, though switch statistics will count matches for both the ACL and VMAP.
314
G8052 Application Guide for ENOS 8.4
VM Policy Bandwidth Control
In a virtualized environment where VEs can migrate between hypervisors and thus move among different ports on the switch, traffic bandwidth policies must be attached to VEs, rather than to a specific switch port.
VM Policy Bandwidth Control allows the administrator to specify the amount of data the switch will permit to flow from a particular VE, without defining a complicated matrix of ACLs or VMAPs for all port combinations where a VE may appear.
VM Policy Bandwidth Control Commands
VM Policy Bandwidth Control can be configured using the following configuration commands:
RS G8052(config)# virt vmpolicy vmbwidth <VM MAC>|<index>|<UUID>| <IPv4 address>|<name>?
txrate <committed rate> <burst> [<ACL number>] (Set the VM transmit bandwidth – ingress for switch)
rxrate <committed rate> <burst>
(Set the VM receive bandwidth – egress
for switch)
bwctrl
(Enable bandwidth control)
Bandwidth allocation can be defined for transmit (TX) traffic or receive (RX) traffic. Because bandwidth allocation is specified from the perspective of the VE, the switch command for TX Rate Control (txrate) sets the data rate to be sent from the VM to the switch, and the RX rate sets the data rate to be received by the VM from the switch.
The committed rate is specified in multiples of 64 kbps, from 64 to 40,000,000. The maximum burst rate is specified as 32, 64, 128, 256, 1024, 2048, or 4096 kb. If both the committed rate and burst are set to 0, bandwidth control will be disabled.
When txrate is specified, the switch automatically selects an available ACL for internal use with bandwidth control. Optionally, if automatic ACL selection is not desired, a specific ACL may be selected. If there are no unassigned ACLs available, txrate cannot be configured.
© Copyright Lenovo 2016
Chapter 17: VMready
315
Bandwidth Policies vs. Bandwidth Shaping
VM Profile Bandwidth Shaping differs from VM Policy Bandwidth Control.
VM Profile Bandwidth Shaping (see “VM Profiles” on page 303) is configured per VM group and is enforced on the server by a virtual switch in the hypervisor. Shaping is unidirectional and limits traffic transmitted from the virtual switch to the G8052. Shaping is performed prior to transmit VM Policy Bandwidth Control. If the egress traffic for a virtual switch port group exceeds shaping parameters, the traffic is dropped by the virtual switch in the hypervisor. Shaping uses server CPU resources, but prevents extra traffic from consuming bandwidth between the server and the G8052.
VM Policy Bandwidth Control is configured per VE, and can be set independently for transmit traffic. Bandwidth policies are enforced by the G8052. VE traffic that exceeds configured levels is dropped by the switch upon ingress. Setting txrate uses ACL resources on the switch.
Bandwidth shaping and bandwidth policies can be used separately or in concert.
316
G8052 Application Guide for ENOS 8.4
VMready Information Displays
The G8052 can be used to display a variety of VMready information.
Note: Some displays depict information collected from scans of a VMware vCenter and may not be available without a valid vCenter. If a vCenter is assigned (see “Assigning a vCenter” on page 310), scan information might not be available for up to two minutes after the switch boots or when VMready is first enabled. Also, any major changes made through the vCenter may take up to two minutes to be reflected on the switch unless you force an immediate vCenter scan (see “vCenter Scans” on page 311.
Local VE Information
A concise list of local VEs and pre‐provisioned VEs is available with the following ISCLI privileged EXEC command: RS G8052# show virt vm
IP Address VMAC Address Index Port VM Group (Profile) Check status ­­­­­­­­­­­­­­­­ ­­­­­­­­­­­­­­­­­ ­­­­­ ­­­­­­­­ ­­­­­­­­­­­­­­­­­­ ­­­­­­­­­­­­
0.0.0.0 00:50:56:55:47:0c 5 17.3 ~0.0.0.0 00:50:56:b3:1e:7b 2 17.3 1 test ~0.0.0.0 00:50:56:b3:1f:16 1 17.3 1 test ~0.0.0.0 00:50:56:b3:2c:b9 4 18 2 ~0.0.0.0 00:50:56:b3:5f:32 3 18 1 test ~0.0.0.0 00:50:56:b3:69:5a 0 19.3 1 test VMReady ports: 17­21
Number of entries: 6
~ indicates inactive VMs
0.0.0.0 indicates IP address not yet available
Note: The Index numbers shown in the VE information displays can be used to specify a particular VE in configuration commands.
© Copyright Lenovo 2016
Chapter 17: VMready
317
If a vCenter is available, more verbose information can be obtained using the following ISCLI privileged EXEC command option: RS G8052# show virt vm ­v
Index MAC Address, Name (VM or Host), Port, Group Vswitch,
IP Address @Host (VMs only) VLAN Port Group
­­­­­ ­­­­­­­­­­­­ ­­­­­­­­­­­­­­­­­­ ­­­­­ ­­­­­ ­­­­­­­­­­
0 00:50:56:ba:1b:23 New Virtual Machine ST 1ST 1 100 vSwitch2
10.10.10.101 @10.241.5.49 100 Lenovo_vlan100
2 00:50:56:ba:25:8a VmForGaborII 26 vSwitch1
10.10.10.101 @10.241.5.49 0 IBM_Default
3 00:50:56:ba:1b:00 New Virtual Machine 2626 vSwitch1
0.0.0.0 @10.241.5.49 100 VM Network 2
­­
3 of 3 entries printed
0.0.0.0 indicates IP Address is not available
Use the "­v ­r" options to refresh data before displaying results
EVB Virtual Station Interface Information:
Total number of VM Association entries : To view additional detail regarding any specific VE, see “vCenter Switchport Mapping Details” on page 320).
vCenter Hypervisor Hosts
If a vCenter is available, the following ISCLI privileged EXEC command displays the name and UUID of all VMware hosts, providing an essential overview of the data center:
RS G8052# show virt vmware hosts
UUID Name(s), IP Address
­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
00a42681­d0e5­5910­a0bf­bd23bd3f7800 172.16.41.30
002e063c­153c­dd11­8b32­a78dd1909a00 172.16.46.10
00f1fe30­143c­dd11­84f2­a8ba2cd7ae00 172.16.44.50
0018938e­143c­dd11­9f7a­d8defa4b8300 172.16.46.20
...
318
G8052 Application Guide for ENOS 8.4
Using the following command, the administrator can view more detailed vCenter host information, including a list of virtual switches and their port groups, as well as details for all associated VEs:
RS G8052# show virt vmware showhost {<UUID>|<IPv4 address>|<host name>}
Vswitches available on the host:
vSwitch0
Port Groups and their Vswitches on the host:
Lenovo_Default vSwitch0
VM Network vSwitch0
Service Console vSwitch0
VMkernel vSwitch0
­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
MAC Address 00:50:56:9c:21:2f
Port 4
Type Virtual Machine
VM vCenter Name halibut
VM OS hostname localhost.localdomain
VM IP Address 172.16.46.15
VM UUID 001c41f3­ccd8­94bb­1b94­6b94b03b9200
Current VM Host 172.16.46.10
Vswitch vSwitch0
Port Group Lenovo_Default
VLAN ID 0
...
vCenter VEs
If a vCenter is available, the following ISCLI privileged EXEC command displays a list of all known VEs:
RS G8052# show virt vmware vms
UUID Name(s), IP Address
­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
001cdf1d­863a­fa5e­58c0­d197ed3e3300 30vm1
001c1fba­5483­863f­de04­4953b5caa700 VM90
001c0441­c9ed­184c­7030­d6a6bc9b4d00 VM91
001cc06e­393b­a36b­2da9­c71098d9a700 vm_new
001c6384­f764­983c­83e3­e94fc78f2c00 sturgeon
001c7434­6bf9­52bd­c48c­a410da0c2300 VM70
001cad78­8a3c­9cbe­35f6­59ca5f392500 VM60
001cf762­a577­f42a­c6ea­090216c11800 30VM6
001c41f3­ccd8­94bb­1b94­6b94b03b9200 halibut, localhost.localdomain,
172.16.46.15
001cf17b­5581­ea80­c22c­3236b89ee900 30vm5
001c4312­a145­bf44­7edd­49b7a2fc3800 vm3
001caf40­a40a­de6f­7b44­9c496f123b00 30VM7
© Copyright Lenovo 2016
Chapter 17: VMready
319
vCenter VE Details
If a vCenter is available, the following ISCLI privileged EXEC command displays detailed information about a specific VE:
RS G8052# show virt vmware showvm {<VM UUID>|<VM IPv4 address>|<VM name>}
­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
MAC Address 00:50:56:9c:21:2f
Port 4
Type Virtual Machine
VM vCenter Name halibut
VM OS hostname localhost.localdomain
VM IP Address 172.16.46.15
VM UUID 001c41f3­ccd8­94bb­1b94­6b94b03b9200
Current VM Host 172.16.46.10
Vswitch vSwitch0
Port Group Lenovo_Default
VLAN ID 0
vCenter Switchport Mapping Details
If a vCenter is available, the following ISCLI privileged EXEC command displays detailed information about VE switchport mapping:
RS G8052# show virt vmware switchport­mapping
ST 5 ==> 10.241.32.133 vmnic5
ST 5 ==> 10.241.32.133 vmnic5
23 ==> 10.241.32.131 vmnic3
320
G8052 Application Guide for ENOS 8.4
VMready Configuration Example
This example has the following characteristics:
A VMware vCenter is fully installed and configured prior to VMready configura‐
tion and includes a “bladevm” administration account and a valid SSL certifi‐
cate.
 The distributed VM group model is used.
 The VM profile named “Finance” is configured for VLAN 30, and specifies NIC‐to‐switch bandwidth shaping for 1Mbps average bandwidth, 2MB bursts, and 3Mbps maximum bandwidth.
 The VM group includes four discovered VMs on switch server ports 1 and 2, and one static LAG (previously configured) that includes switch uplink ports 3 and 4.

1. Define the server ports. RS G8052(config)# system server­ports port 1­2
2. Enable the VMready feature.
RS G8052(config)# virt enable
3. Specify the VMware vCenter IPv4 address.
RS G8052(config)# virt vmware vmware vcspec 172.16.100.1 bladevm
When prompted, enter the user password that the switch must use for access to the vCenter.
4. Create the VM profile.
RS G8052(config)# virt vmprofile Finance
RS G8052(config)# virt vmprofile edit Finance vlan 30
RS G8052(config)# virt vmprofile edit Finance shaping 1000 2000 3000
5. Define the VM group.
RS
RS
RS
RS
RS
RS
G8052(config)# virt vmgroup 1 profile Finance
G8052(config)# virt vmgroup 1 vm arctic
G8052(config)# virt vmgroup 1 vm monster
G8052(config)# virt vmgroup 1 vm sierra
G8052(config)# virt vmgroup 1 vm 00:50:56:4f:f2:00
G8052(config)# virt vmgroup 1 portchannel 1
When VMs are added, the server ports on which they appear are automatically added to the VM group. In this example, there is no need to manually add ports 1 and 2.
6. If necessary, enable VLAN tagging for the VM group:
RS G8052(config)# virt vmgroup 1 tag
Note: If the VM group contains ports that also exist in other VM groups, make sure tagging is enabled in both VM groups. In this example configuration, no ports exist in more than one VM group.
© Copyright Lenovo 2016
Chapter 17: VMready
321
322
G8052 Application Guide for ENOS 8.4
Chapter 18. Edge Virtual Bridging
The 802.1Qbg/Edge Virtual Bridging (EVB) is an emerging IEEE standard for allowing networks to become virtual machine (VM)‐aware. EVB bridges the gap between physical and virtual network resources. The IEEE 802.1Qbg simplifies network management by providing a standards‐based protocol that defines how virtual Ethernet bridges exchange configuration information. In EVB environments, physical end stations, containing multiple virtual end stations, use a bridge to form a LAN. The virtual NIC (vNIC) configuration information of a virtual machine is available to these EVB devices. This information is generally not available to an 802.1Q bridge.
Lenovo Enterprise Network Operating System EVB features are compliant with the IEEE 802.1Qbg Authors Group Draft 0.2. For a list of documents on this feature, see: http://www.ieee802.org/1/pages/802.1bg.html.
The Lenovo RackSwitch G8052 performs the role of a 802.1Qbg bridge in an EVB environment.
Enterprise NOS implementation of EVB supports the following protocols:
© Copyright Lenovo 2016

Virtual Ethernet Bridging (VEB) and Virtual Ethernet Port Aggregator (VEPA): VEB and VEPA are mechanisms for switching between VMs on the same hypervisor. VEB enables switching with the server, either in the software (vSwitch), or in the hardware (using single root I/O virtualization capable NICs). VEPA requires the edge switch to support “Reflective Relay”— an operation where the switch forwards a frame back to the port on which it arrived if the destination MAC address is on the same port.

Edge Control Protocol (ECP): ECP is a transport protocol that operates between two peers over an IEEE 802 LAN. ECP provides reliable, in‐order delivery of ULP (Upper Layer Protocol) PDUs (Protocol Data Units). 
Virtual Station Interface (VSI) Discovery and Configuration Protocol (VDP): VDP allows hypervisors to advertise VSIs to the physical network. This protocol also allows centralized configuration of network policies that will persist with the VM, independent of its location.

EVB Type‐Length‐Value (TLV): EVB TLV is a Link Layer Discovery protocol (LLDP)‐based TLV used to discover and configure VEPA, ECP, and VDP.
Chapter 18: Edge Virtual Bridging
323
EVB Operations Overview
The ENOS includes a pre‐standards VSI Type Database (VSIDB) implemented through the System Networking Switch Center (SNSC), the IBM Flex System Manager (FSM), or the IBM System Networking Distributed Switch 5000V. The VSIDB is the central repository for defining sets of network policies that apply to VM network ports. You can configure only one VSIDB.
Note: This document does not include the VSIDB configuration details. Please see the SNSC, FSM, or IBM System Networking Distributed Switch 5000V guide for details on how to configure VSIDB.
The VSIDB operates in the following sequence:
1. Define VSI types in the VSIDB. The VSIDB exports the database when the G8052 metering sends a request.
2. Create a VM. Specify VSI type for each VM interface. See the SNSC, FSM, or IBM System Networking Distributed Switch 5000V guide for details on how to specify the VSI type.
The hypervisor sends a VSI ASSOCIATE, which contains the VSI type ID, to the switch port after the VM is started. The switch updates its configuration based on the requested VSI type. The switch configures the per‐VM bandwidth using the VMpolicy.
The ENOS supports the following policies for VMs:

ACLs

Bandwidth VSIDB Synchronization
The switch periodically checks for VSIDB changes based on the configured interval. You can configure this interval using the following command: RS G8052(config)# virt evb vsidb <number>
RS G8052(conf­vsidb)# [no] update­interval <time in seconds>
To disable periodic updates, use the “no update­interval” command.
If the switch finds that the VSIDB has changed, it updates the local VSIDB cache. When the cache is successfully updated, it sends a syslog message.
After updating the local VSIDB cache, the switch disassociates any VM whose type ID or VLAN no longer exists in the updated cache.
The switch updates the local VSIDB cache when any of the following takes place:
324

When, at the configured refresh interval, the switch finds that the VSIDB configuration has changed since the last poll. 
When a VM sends an ASSOCIATE message, but the VSI type does not exist in the local VSIDB cache.

When a VM sends an ASSOCIATE message, and the VSI type exists but the VSI type’s VLAN ID does not exist in the local VSIDB cache.
G8052 Application Guide for ENOS 8.4
When you update the VSIDB using the following command:

RS G8052# virt evb update vsidb <number>
When the management port link status changes from down to up

VLAN Behavior
When a VM gets associated, the corresponding VLAN is dynamically created on the switch port if the VLAN does not already exist. VLANs that are dynamically created will be automatically removed from the switch port when there are no VMs using that VLAN on the port.
Dynamic VLAN information will not be displayed in the running configuration. However, the VLAN, port, and STP commands display the dynamic VLAN information with a “*”. If you configure any Layer 2/Layer 3 features on dynamically created VLANs, the VLAN information is displayed in the running configuration.
Deleting a VLAN
If you delete a VLAN that has a VM associated with it, you will see a warning message similar to the following: Warning: Vlan 10 is used by VM and can't be removed.
The VMs will not get disassociated.
If a VM is associated with a port, and you remove this port from a VLAN, you will see a warning message similar to the following: Warning: Port 23 in Vlan 10 is used by VM and can't be removed.
The VMs will not get disassociated.
Manual Reflective Relay
Reflective Relay (RR) is an operation where the switch forwards a frame back to the port on which it arrived if the destination MAC address is on the same port. When an EVB profile is configured on a port, RR is automatically enabled on the port after capability exchange with the peer, using the IEEE802.1QBG protocol. This is the usual mode of operation.
When the switch interoperates with devices that do not support IEEE 802.1QBG protocols, RR can be manually configured using the following command:
RS G8052(config­if)# reflective­relay force
Manual RR and EVB profile cannot be configured on a port at the same time.
If a port belongs to an isolated VLAN, Manual RR will not work for the respective port.
© Copyright Lenovo 2016
Chapter 18: Edge Virtual Bridging
325
EVB Configuration
This section includes the steps to configure EVB based on the following values:

Profile number: 1

Port number: 1

Retry interval: 8000 milliseconds

VSI Database: 
Manager IP: 172.31.37.187

Port: 80
Note: VSI Database can be accessed via HTTP or HTTPS. The manager IP can be configured with an IPv4 or IPv6 address. 1. Create an EVB profile. RS G8052(config)# virt evb profile 1 (Enter number from 1‐16)
2. Enable Reflective Relay. RS G8052(conf­evbprof)# reflective­relay 3. Enable VSI discovery. RS G8052(conf­evbprof)# vsi­discovery
RS G8052(conf-evbprof)# exit 4. Enable a server port.
RS G8052(config)# system server­ports port <port‐number>
5. Add EVB profile to port. RS G8052(config)# interface port 1
RS G8052(config-if)# evb profile 1 (Enter EVB profile ID)
RS G8052(config­if)# exit
6. Configure ECP retransmission interval. RS G8052(config)# ecp retransmit­interval 8000 (Enter retransmission interval in milliseconds (100‐9000)
326
G8052 Application Guide for ENOS 8.4
7. Set VSI database information. RS
RS
RS
RS
RS
RS
RS
G8052(config)# virt evb vsidb 1
G8052(conf­vsidb)# host 172.31.37.187 (Set VSI database Manager IP)
G8052(conf­vsidb)# port 80 (Set VSI database Manager port)
G8052(conf­vsidb)# filepath “vsidb” (Set VSI database document path)
G8052(conf­vsidb)# filename “all.xml”(Set VSI database file name)
G8052(conf­vsidb)# update­interval 30(Set update interval in seconds) G8052(conf­vsidb)# exit
Note: When you connect to an SNSC VSIDB, the port/docpath configuration is as follows:
HTTP:

Port: 40080

Docpath: snsc/rest/vsitypes
HTTPS:

Port: 40443

Docpath: snsc/rest/vsitypes
When you connect to a 5000v VSIDB, the port/docpath configuration is as follows:

Port: 80

Docpath: vsitypes
8. Enable LLDP. © Copyright Lenovo 2016
Chapter 18: Edge Virtual Bridging
327
Limitations

If both ACL and egress bandwidth metering are enabled, traffic will first be matched with the ACL and will not be limited by bandwidth metering.

ACLs based on a source MAC or VLAN must match the source MAC and VLAN of the VM. If not, the policy will be ignored and you will see the following warning message:
"vm: VSI Type ID 100 Associated mac 00:50:56:b6:c0:ff on port 6, ignore 1 mismatched ACL"
Unsupported features
The following features are not supported with EVB:
328

LAG/VLAG

vNIC

Stacking
G8052 Application Guide for ENOS 8.4
Chapter 19. Static Multicast ARP
The Microsoft Windows operating system includes Network Load Balancing (NLB) technology that helps to balance incoming IP traffic among multi‐node clusters. In multicast mode, NLB uses a shared multicast MAC address with a unicast IP address. Since the address resolution protocol (ARP) can map an IP address to only one MAC address, port, and VLAN, the packet reaches only one of the servers (the one attached to the port on which the ARP was learnt).
To avoid the ARP resolution, you must create a static ARP entry with multicast MAC address. You must also specify the list of ports through which the multicast packet must be sent out from the gateway or Layer 2/Layer 3 node.
With these configurations, a packet with a unicast IPv4 destination address and multicast MAC address can be sent out as per the multicast MAC address configuration. NLB maps the unicast IP address and multicast MAC address as follows:
Cluster multicast MAC address: 03‐BF‐W‐X‐Y‐Z; where W.X.Y.Z is the cluster unicast IP address.
You must configure the static multicast ARP entry only at the Layer 2/Layer 3 or Router node, and not at the Layer 2‐only node.
Lenovo Enterprise Network Operating System supports a maximum of 20 static multicast ARP entries. When the ARP table is full, an error message appears in the syslog.
Note: If you use the ACL profile, an ACL entry is consumed for each Static Multicast ARP entry that you configure. Hence, you can configure a maximum of 896 ACLs and multicast MAC entries together when using the ACL profile.The ACL entries have a higher priority. In the default profile, the number of static multicast ARP entries that you configure does not affect the total number of ACL entries.
© Copyright Lenovo 2016
Chapter 19: Static Multicast ARP
329
Configuring Static Multicast ARP
To configure multicast MAC ARP, you must perform the following steps:

Configure the static multicast forwarding database (FDB) entry: Since there is no port list specified for static multicast ARP, and the associated MAC address is multicast, you must specify a static multicast FDB entry for the cluster MAC address to limit the multicast domain. If there is no static multicast FDB entry defined for the cluster MAC address, traffic will not be forwarded. Use the following command: RS G8052(config)# mac­address­table multicast <cluster MAC address> <port(s)>

Configure the static multicast ARP entry: Multicast ARP static entries should be configured without specifying the list of ports to be used. Use the following command: RS G8052(config)# ip arp <destination unicast IP address> <destination multicast MAC address> vlan <cluster VLAN number>
Configuration Example
Consider the following example:

Cluster unicast IP address: 10.10.10.42

Cluster multicast MAC address: 03:bf:0A:0A:0A:2A 
Cluster VLAN: 42

List of individual or port LAGs to which traffic should be forwarded: 54 and 56
Following are the steps to configure the static multicast ARP based on the given example:
1. Configure the static multicast FDB entry. RS G8052(config)# mac­address­table multicast 03:bf:0A:0A:0A:2A 42 54,56
2. Configure the static multicast ARP entry: RS G8052(config)# ip arp 10.10.10.42 03:bf:0A:0A:0A:2A vlan 42
You can verify the configuration using the following commands:

Verify static multicast FDB entry: RS G8052(config)# show mac­address­table multicast address 03:bf:0A:0A:0A:2A
Multicast Address VLAN Port(s)
­­­­­­­­­­­­­­­­­ ­­­­ ­­­­­­­­­
03:bf:0A:0A:0A:2A 42 54 56
330
G8052 Application Guide for ENOS 8.4

Verify static multicast ARP entry: RS G8052(config)# show ip arp
Current ARP configuration:
rearp 5
Current static ARP:
ip mac port vlan
­­­­­­­­­­­­­­­ ­­­­­­­­­­­­­­­­­ ­­­­­ ­­­­
10.10.10.42 03:bf:0A:0A:0A:2A 42
­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
Total number of arp entries : 2
IP address Flags MAC address VLAN Age Port
­­­­­­­­­­­­­­­ ­­­­­ ­­­­­­­­­­­­­­­­­ ­­­­ ­­­ ­­­­
10.10.10.1 P fc:cf:62:9d:74:00 42 10.10.10.42 P 03:bf:0A:0A:0A:2A 42 0 © Copyright Lenovo 2016
Chapter 19: Static Multicast ARP
331
Limitations
332

You must configure the ARP only in the Layer 2/Layer 3 node or the router node but not in the Layer 2‐only node. Enterprise NOS cannot validate if the node is Layer 2‐only. 
The packet is always forwarded to all the ports as specified in the Multicast MAC address configuration. If VLAN membership changes for the ports, you must update this static multicast MAC entry. If not, the ports, whose membership has changed, will report discards.

ACLs take precedence over static multicast ARP. If an ACL is configured to match and permit ingress of unicast traffic, the traffic will be forwarded based on the ACL rule, and the static multicast ARP will be ignored. G8052 Application Guide for ENOS 8.4
Chapter 20. Dynamic ARP Inspection
Address Resolution Protocol (ARP) provides IP communication within a Layer 2 broadcast domain by mapping an IP address to a MAC address. Network devices maintain this mapping in a cache that they consult when forwarding packets to other devices. If the ARP cache does not contain an entry for the destination device, the host broadcasts an ARP request for that deviceʹs address and stores the response in the cache.
Understanding ARP Spoofing Attacks
ARP spoofing (also referred to as ARP cache poisoning) is one way to initiate man‐in‐the‐middle attacks. A malicious user could poison the ARP caches of connected systems (hosts, switches, routers) by sending forged ARP responses and could intercept traffic intended for other hosts on the LAN segment.
For example, in Figure 26, the attacker (Host C) can send an ARP Reply to Host A pretending to be Host B. As a result, Host A populates its ARP cache with a poisoned entry having IP address IB and MAC address MC. Host A will use the MAC address MC as the destination MAC address for traffic intended for Host B. Host C then intercepts that traffic. Because Host C knows the true MAC addresses associated with Host B, it forwards the intercepted traffic to that host by using the correct MAC address as the destination, keeping the appearance of regular behavior.
Figure 26. ARP Cache Poisoning
Host A
(IA, MA)
A
B
Host B
(IB, MB)
C
Host C (man-in-the-middle)
(IC, MC)
Understanding DAI
Dynamic ARP Inspection is a security feature that lets the switch intercept and examine all ARP request and response packets in a subnet, discarding those packets with invalid IP to MAC address bindings. This capability protects the network from man‐in‐the‐middle attacks.
A switch on which ARP Inspection is configured does the following:
© Copyright Lenovo 2016

Intercepts all ARP requests and responses on untrusted ports.

Verifies that each of these intercepted packets has a valid IP/MAC/VLAN/port binding before updating the local ARP cache or before forwarding the packet to the appropriate destination.
333

Drops invalid ARP packets and sends a syslog message with details about each dropped packet.
DAI determines the validity of an ARP packet based on valid IP‐to‐MAC address bindings stored in a trusted database, the DHCP snooping binding database. This database is built by DHCP snooping if DHCP snooping is enabled on the VLANs and on the switch. As shown in Figure 27, if the ARP packet is received on a trusted interface, the switch forwards the packet without any checks. On untrusted interfaces, the switch forwards the packet only if it is valid.
For hosts with statically configured IP addresses, static DHCP snooping binding entries can be configured with a big lease time.
Figure 27. Dynamic ARP inspection at work
Valid
Packets
ARP
Packets
ARP
Packets
Trusted
Interface
Untrusted
Interface
DAI
DHCP
Snooping/
Binding
DB
Invalid
Packet
Interface Trust States and Network Security
DAI associates a trust state with each interface on the switch.
In a typical network configuration, you configure all switch ports connected to host ports as untrusted and configure all switch ports connected to switches as trusted. With this configuration, all ARP packets entering the network from a given switch bypass the security check. The trust state configuration should be done carefully: configuring interfaces as untrusted when they should be trusted can result in a loss of connectivity.
In Figure 28, assume that both Switch A and Switch B are running DAI on the VLAN that includes Host 1 and Host 2. If Host 1 and Host 2 acquire their IP addresses from the DHCP server connected to Switch A, only Switch A has the DHCP IP‐to‐MAC binding of Host 1. Therefore, if the interface between Switch A and Switch B is untrusted, the ARP packets from Host 1 are dropped by Switch B. Connectivity between Host 1 and Host 2 is lost.
334
G8052 Application Guide for ENOS 8.4
Figure 28. ARP Packet Validation on a VLAN Enabled for DAI
DHCP server
Port 1
Switch A
Port 2
Port 3
Host 1
Switch B
Port 2
Port 3
Host 2
If Switch A is not running DAI, Host 1 can easily poison the ARP caches of Switch B and Host 2, if the link between the switches is configured as trusted. This condition can occur even though Switch B is running DAI.
The best option for the setup from Figure 28 is to have DAI running on both switches and to have the link between the switches configured as trusted.
In cases in which some switches in a VLAN run DAI and other switches do not, configure the interfaces connecting such switches as untrusted. However, to validate the bindings of packets from switches where DAI is not configured, configure static DHCP snooping binding entries on the switch running DAI. When you cannot determine such bindings, isolate switches running DAI at Layer 3 from switches not running DAI.
DAI ensures that hosts (on untrusted interfaces) connected to a switch running DAI do not poison the ARP caches of other hosts in the network. However, DAI does not prevent hosts in other portions of the network connected through a trusted interface from poisoning the caches of the hosts that are connected to a switch running DAI.
© Copyright Lenovo 2016
Chapter 20: Dynamic ARP Inspection
335
DAI Configuration Guidelines and Restrictions
When configuring DAI, follow these guidelines and restrictions:

DAI is an ingress security feature; it does not perform any egress checking.

DAI is not effective for hosts connected to switches that do not support DAI or that do not have this feature enabled. Because man‐in‐the‐middle attacks are limited to a single Layer 2 broadcast domain, separate the domain with DAI checks from the one with no checking. This action secures the ARP caches of hosts in the domain enabled for DAI.

DAI depends on the entries in the DHCP snooping binding database to verify IP‐to‐MAC address bindings in incoming ARP requests and ARP responses.

For non‐DHCP environments, for each static IP address add a static DHCP Snooping binding entry with the biggest lease time in order not to expire.

Ports belonging to a port‐channel must have the same trust state.
DAI Configuration Example
Following is the configuration for the example in Figure 28.
SwitchA(config)# interface port 1­3
SwitchA(config­if)# switchport access vlan 2
SwitchA(config)# interface port 1­2
SwitchA(config­if)# ip arp inspection trust
SwitchA(config­if)# exit
SwitchA(config)# interface port 3
SwitchA(config­if)# no ip arp inspection trust
SwitchA(config­if)# exit
SwitchA(config)# ip arp inspection vlan 2
SwitchB(config)# interface port 2­3
SwitchB(config­if)# switchport access vlan 2
SwitchB(config)# interface port 2
SwitchB(config­if)# ip arp inspection trust
SwitchB(config­if)# exit
SwitchB(config)# interface port 3
SwitchB(config­if)# no ip arp inspection trust
SwitchB(config­if)# exit
SwitchB(config)# ip arp inspection vlan 2
336
G8052 Application Guide for ENOS 8.4
The DHCP Snooping binding tables will be similar to the following: Mac Address IP Address Lease(seconds) Type VLAN Interface ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
­­­­­
00:00:00:00:00:01 Host1_IP 1000 Dynamic 2 3 00:00:00:00:00:02 Host2_IP 2000 Dynamic 2 2
Total number of bindings: 2
SwitchB#show ip dhcp snooping binding Mac Address IP Address Lease(seconds) Type VLAN Interface ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
­­­­­ 00:00:00:00:00:02 Host2_IP 2000 Dynamic 2 3
Total number of bindings: 1
SwitchA# show ip dhcp snooping binding Output of show commands:
SwitchA# show ip arp inspection vlan
Vlan
­­­­
Configuration ­­­­­­­­­­­­­
2
Enabled
SwitchA# show ip arp inspection interfaces
Interface
­­­­­­­­­
Trust State
­­­­­­­­­­­
1Trusted
2Trusted
3Untrusted
4Untrusted
...
SwitchA# show ip arp inspection statistics
Vlan
­­­­
ForwardedDropped
­­­­­­­­­­­­­­­­
2
100 200
When Host 1 tries to send an ARP with an IP address of 1.1.1.3 that is not present in the DHCP Binding table, the packet is dropped and an error message similar to the following is logged: “Dec 16 21:00:10 192.168.49.50 NOTICE ARP­Inspection: Invalid ARP Request on port 3, VLAN 2 ([00:02:00:02:00:02/1.1.1.3/00:00:00:00:00:00/1.1.1.4])”
© Copyright Lenovo 2016
Chapter 20: Dynamic ARP Inspection
337
338
G8052 Application Guide for ENOS 8.4
Part 5: IP Routing
This section discusses Layer 3 switching functions. In addition to switching traffic at near line rates, the application switch can perform multi‐protocol routing. This section discusses basic routing and advanced routing protocols:
 Basic IP Routing
 Policy‐Based Routing
 Routed Ports
 Internet Protocol Version 6
 IPsec with IPv6
 Routing Information Protocol
 Internet Group Management Protocol
 Multicast Listener Discovery
 Border Gateway Protocol
 Open Shortest Path First
 Protocol Independent Multicast
© Copyright Lenovo 2016
339
340
G8052 Application Guide for ENOS 8.4
Chapter 21. Basic IP Routing
This chapter provides configuration background and examples for using the G8052 to perform IP routing functions. The following topics are addressed in this chapter:
© Copyright Lenovo 2016

“IP Routing Benefits” on page 342

“Routing Between IP Subnets” on page 342

“Example of Subnet Routing” on page 343

“ECMP Static Routes” on page 347

“Dynamic Host Configuration Protocol” on page 349

“DHCP Relay Agent” on page 350
341
IP Routing Benefits
The switch uses a combination of configurable IP switch interfaces and IP routing options. The switch IP routing capabilities provide the following benefits:

Connects the server IP subnets to the rest of the backbone network.

Provides the ability to route IP traffic between multiple Virtual Local Area Networks (VLANs) configured on the switch.
Routing Between IP Subnets
The physical layout of most corporate networks has evolved over time. Classic hub/router topologies have given way to faster switched topologies, particularly now that switches are increasingly intelligent. The G8052 is intelligent and fast enough to perform routing functions at wire speed. The combination of faster routing and switching in a single device allows you to build versatile topologies that account for legacy configurations.
For example, consider a corporate campus that has migrated from a router‐centric topology to a faster, more powerful, switch‐based topology. As is often the case, the legacy of network growth and redesign has left the system with a mix of illogically distributed subnets.
This is a situation that switching alone cannot cure. Instead, the router is flooded with cross‐subnet communication. This compromises efficiency in two ways:

Routers can be slower than switches. The cross‐subnet side trip from the switch to the router and back again adds two hops for the data, slowing throughput considerably.

Traffic to the router increases, increasing congestion.
Even if every end‐station could be moved to better logical subnets (a daunting task), competition for access to common server pools on different subnets still burdens the routers.
This problem is solved by using switches with built‐in IP routing capabilities. Cross‐subnet LAN traffic can now be routed within the switches with wire speed switching performance. This eases the load on the router and saves the network administrators from reconfiguring every end‐station with new IP addresses.
342
G8052 Application Guide for ENOS 8.4
Example of Subnet Routing
Consider the role of the G8052 in the following configuration example: Figure 29. Switch‐Based Routing Topology Default router:
205.21.17.1
IF 1
VLAN 1
IF 2
VLAN 2
IF 4
VLAN 4
IF 3
VLAN 3
Server subnet 3:
206.30.15.2-254
Server subnet 1:
100.20.10.2-254
Server subnet 2:
131.15.15.2-254
The switch connects the Gigabit Ethernet and Fast Ethernet LAGs from various switched subnets throughout one building. Common servers are placed on another subnet attached to the switch. A primary and backup router are attached to the switch on yet another subnet.
Without Layer 3 IP routing on the switch, cross‐subnet communication is relayed to the default gateway (in this case, the router) for the next level of routing intelligence. The router fills in the necessary address information and sends the data back to the switch, which then relays the packet to the proper destination subnet using Layer 2 switching.
With Layer 3 IP routing in place on the switch, routing between different IP subnets can be accomplished entirely within the switch. This leaves the routers free to handle inbound and outbound traffic for this group of subnets.
© Copyright Lenovo 2016
Chapter 21: Basic IP Routing
343
Using VLANs to Segregate Broadcast Domains
If you want to control the broadcasts on your network, use VLANs to create distinct broadcast domains. Create one VLAN for each server subnet, and one for the router. Configuration Example
This section describes the steps used to configure the example topology shown in Figure 29 on page 343. 1. Assign an IP address (or document the existing one) for each router and each server. The following IP addresses are used:
Table 27. Subnet Routing Example: IP Address Assignments
Subnet
Devices
IP Addresses
1
Default router
205.21.17.1
2
Web servers
100.20.10.2-254
3
Database servers
131.15.15.2-254
4
Terminal Servers
206.30.15.2-254
2. Assign an IP interface for each subnet attached to the switch.
Since there are four IP subnets connected to the switch, four IP interfaces are needed:
Table 28. Subnet Routing Example: IP Interface Assignments
Interface
Devices
IP Interface Address
IF 1
Default router
205.21.17.3
IF 2
Web servers
100.20.10.1
IF 3
Database servers
131.15.15.1
IF 4
Terminal Servers
206.30.15.1
3. Determine which switch ports and IP interfaces belong to which VLANs.
The following table adds port and VLAN information:
Table 29. Subnet Routing Example: Optional VLAN Ports
Devices
344
IP Interface
Switch Ports
Default router
1
22
1
Web servers
2
1 and 2
2
Database servers
3
3 and 4
3
Terminal Servers
4
5 and 6
4
G8052 Application Guide for ENOS 8.4
VLAN #
Note: To perform this configuration, you must be connected to the switch Industry Standard Command Line Interface (ISCLI) as the administrator. 4. Add the switch ports to their respective VLANs.
The VLANs shown in Table 29 are configured as follows: RS
RS
RS
RS
RS
RS
G8052(config)# vlan 1
G8052(config­vlan)# exit
G8052(config)# interface port 22
(Add ports to VLAN 1)
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 1
G8052(config­if)# exit
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 2
G8052(config­vlan)# exit
G8052(config)# interface port 1,2 (Add ports to VLAN 2)
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 2
G8052(config­if)# exit
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 3
G8052(config­vlan)# exit
G8052(config)# interface port 3,4 (Add ports to VLAN 3)
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 3
G8052(config­if)# exit
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 4
G8052(config­vlan)# exit
G8052(config)# interface port 5,6 (Add ports to VLAN 4)
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 4
G8052(config­if)# exit
Each time you add a port to a VLAN, you may get the following prompt:
Port 4 is an untagged port and its PVID is changed from 1 to 3.
© Copyright Lenovo 2016
Chapter 21: Basic IP Routing
345
5. Assign a VLAN to each IP interface. Now that the ports are separated into VLANs, the VLANs are assigned to the appropriate IP interface for each subnet. From Table 29 on page 344, the settings are made as follows: RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface ip 1
(Select IP interface 1)
G8052(config­ip­if)# ip address 205.21.17.3
G8052(config­ip­if)# ip netmask 255.255.255.0
G8052(config­ip­if)# vlan 1
(Add VLAN 1)
G8052(config­ip­if)# enable
G8052(config­vlan)# exit
G8052(config)# interface ip 2
(Select IP interface 2)
G8052(config­ip­if)# ip address 100.20.10.1
G8052(config­ip­if)# ip netmask 255.255.255.0
G8052(config­ip­if)# vlan 2
(Add VLAN 2)
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
G8052(config)# interface ip 3
(Select IP interface 3)
G8052(config­ip­if)# ip address 131.15.15.1
G8052(config­ip­if)# ip netmask 255.255.255.0
G8052(config­ip­if)# vlan 3
(Add VLAN 3)
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
G8052(config)# interface ip 4
(Select IP interface 4)
G8052(config­ip­if)# ip address 206.30.15.1
G8052(config­ip­if)# ip netmask 255.255.255.0
G8052(config­ip­if)# vlan 4
(Add VLAN 4)
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
6. Configure the default gateway to the routers’ addresses. The default gateway allows the switch to send outbound traffic to the router: RS G8052(config)# ip gateway 1 address 205.21.17.1
RS G8052(config)# ip gateway 1 enable
7. Enable IP routing. RS G8052(config)# ip routing
8. Verify the configuration.
RS G8052(config)# show vlan
RS G8052(config)# show interface information
RS G8052(config)# show interface ip
Examine the resulting information. If any settings are incorrect, make the appropriate changes.
346
G8052 Application Guide for ENOS 8.4
ECMP Static Routes
Equal‐Cost Multi‐Path (ECMP) is a forwarding mechanism that routes packets along multiple paths of equal cost. ECMP provides equally‐distributed link load sharing across the paths. The hashing algorithm used is based on the destination IP and source IP (DIPSIP) addresses or only on the source IP address (SIP). ECMP routes allow the switch to choose between several next hops toward a given destination. The switch performs periodic health checks (ping) on each ECMP gateway. If a gateway fails, it is removed from the routing table, and an SNMP trap is sent. ECMP Route Hashing
You can configure the parameters used to perform ECMP route hashing, as follows: 

sip: Source IP address dipsip: Source IP address and destination IP address (default)
The ECMP hash setting applies to all ECMP routes. © Copyright Lenovo 2016
Chapter 21: Basic IP Routing
347
Configuring ECMP Static Routes
To configure ECMP static routes, add the same route multiple times, each with the same destination IP address, but with a different gateway IP address. These routes become ECMP routes. 1. Add a static route (IP address, subnet mask, gateway, and interface number). RS G8052(config)# ip route 10.10.1.1 255.255.255.255 100.10.1.1 1
2. Add another static route with the same IP address and mask, but a different gateway address. RS G8052(config)# ip route 10.10.1.1 255.255.255.255 200.20.2.2 1
3. Select an ECMP hashing method (optional). RS G8052(config)# ip route ecmphash [sip|dipsip]
You may add up to 5 gateways for each static route. Use the following commands to check the status of ECMP static routes: RS G8052(config)# show ip route static
Current static routes:
Destination Mask Gateway If ECMP ­­­­­­­­­­­­­­­ ­­­­­­­­­­­­­­­ ­­­­­­­­­­­­­­­ ­­­­ ­­­­­­
10.20.2.2 255.255.255.255 10.4.4.1 * 10.5.5.1 * 10.6.6.1 * ...
10.35.35.1 * ECMP health­check ping interval: 1
ECMP health­check retries number: 3
ECMP Hash Mechanism: dipsip
Gateway healthcheck: enabled
RS G8052(config)# show ip ecmp Current ecmp static routes:
Destination Mask Gateway If GW Status ­­­­­­­­­­­­­­­ ­­­­­­­­­­­­­­­ ­­­­­­­­­­­­­­­ ­­­­ ­­­­­­­­­­­ 10.20.2.2 255.255.255.255 10.4.4.1 up
10.5.5.1 up
10.6.6.1 up
...
10.34.34.1 up
10.35.35.1 up
348
G8052 Application Guide for ENOS 8.4
Dynamic Host Configuration Protocol
Dynamic Host Configuration Protocol (DHCP) is a transport protocol that provides a framework for automatically assigning IP addresses and configuration information to other IP hosts or clients in a large TCP/IP network. Without DHCP, the IP address must be entered manually for each network device. DHCP allows a network administrator to distribute IP addresses from a central point and automatically send a new IP address when a device is connected to a different place in the network. The switch accepts gateway configuration parameters if they have not been configured manually. The switch ignores DHCP gateway parameters if the gateway is configured. DHCP is an extension of another network IP management protocol, Bootstrap Protocol (BOOTP), with an additional capability of being able to allocate reusable network addresses and configuration parameters for client operation. Built on the client/server model, DHCP allows hosts or clients on an IP network to obtain their configurations from a DHCP server, thereby reducing network administration. The most significant configuration the client receives from the server is its required IP address; (other optional parameters include the “generic” file name to be booted, the address of the default gateway, and so forth).
To enable DHCP on a switch interface, use the following command: RS G8052(config)# system dhcp
© Copyright Lenovo 2016
Chapter 21: Basic IP Routing
349
DHCP Relay Agent
DHCP is described in RFC 2131, and the DHCP relay agent supported on the G8052 is described in RFC 1542. DHCP uses UDP as its transport protocol. The client sends messages to the server on port 67 and the server sends messages to the client on port 68.
DHCP defines the methods through which clients can be assigned an IP address for a finite lease period and allowing reassignment of the IP address to another client later. Additionally, DHCP provides the mechanism for a client to gather other IP configuration parameters it needs to operate in the TCP/IP network.
In the DHCP environment, the G8052 acts as a relay agent. The DHCP relay feature enables the switch to forward a client request for an IP address to two BOOTP servers with IP addresses that have been configured on the switch.
When a switch receives a UDP broadcast on port 67 from a DHCP client requesting an IP address, the switch acts as a proxy for the client, replacing the client source IP (SIP) and destination IP (DIP) addresses. The request is then forwarded as a UDP Unicast MAC layer message to two BOOTP servers whose IP addresses are configured on the switch. The servers respond as a UDP Unicast message back to the switch, with the default gateway and IP address for the client. The destination IP address in the server response represents the interface address on the switch that received the client request. This interface address tells the switch on which VLAN to send the server response to the client.
To enable the G8052 to be the BOOTP forwarder, you need to configure the DHCP/BOOTP server IP addresses on the switch. Generally, it is best to configure the switch IP interface on the client side to match the client’s subnet, and configure VLANs to separate client and server subnets. The DHCP server knows from which IP subnet the newly allocated IP address will come.
In G8052 implementation, there is no need for primary or secondary servers. The client request is forwarded to the BOOTP servers configured on the switch. The use of two servers provide failover redundancy. However, no health checking is supported.
Use the following commands to configure the switch as a DHCP relay agent:
RS
RS
RS
RS
G8052(config)# ip bootp­relay server 1 <IP address>
G8052(config)# ip bootp­relay server 2 <IP address>
G8052(config)# ip bootp­relay enable
G8052(config)# show ip bootp­relay Additionally, DHCP Relay functionality can be assigned on a per interface basis. Use the following commands to enable the Relay functionality: RS G8052(config)# interface ip <Interface number>
RS G8052(config­ip­if)# relay 350
G8052 Application Guide for ENOS 8.4
Chapter 22. Policy-Based Routing
Policy‐based routing (PBR) allows the Lenovo RackSwitch G8052 to forward traffic based on defined policies rather than entries in the routing table. Such policies are defined based on the protocol, source IP, or other information present in a packet header. PBR provides a mechanism for applying the defined policies based on access control lists (ACLs), and marking packets with a type of service (ToS) to provide preferential treatment. PBR can be applied only to the ingress traffic. You can configure a PBR policy using route maps and apply the route map to an ingress interface. You need to specify the match (using ACLs) and set (using route maps) criteria in the policy. Based on the defined rules, an action is triggered. If no match is found, or the policy rule specifies that the packet be denied, the packet is routed based on an entry in the routing table.
© Copyright Lenovo 2016
351
PBR Policies and ACLs
Up to 640 ACLs can be configured for networks that use IPv4 addressing. Regular ACLs and PBR ACLs together cannot exceed the maximum ACLs supported.
ACLs are prioritized based on the ACL number. Lower numbers have higher priority. You must configure regular ACLs with lower numbers and PBR ACLs with higher numbers.
Note: You cannot apply an ACL directly to an interface and using a PBR policy at the same time. Applying PBR ACLs
PBR ACLs must be applied to an IP interface that has a VLAN configured. In addition to the defined ACL rules, the Lenovo Enterprise Network Operating System uses the VLAN ID as a matching criterion. Traffic is filtered on a per‐VLAN basis rather than a per‐interface basis. If multiple IP interfaces have the same VLAN ID, route maps applied to each interface are used to filter traffic on the VLAN. For example: if interface IP 10 and interface IP 11 are members of VLAN 100; interface IP 10 uses PBR ACL 410 and interface IP 11 uses PBR ACL 411. Traffic on VLAN 100 will be filtered using PBR ACLs 410 and 411.
Note: You cannot apply the PBR ACL to a Layer 2‐only port.
352
G8052 Application Guide for ENOS 8.4
Configuring Route Maps
A route map is used to control and modify routing information. When PBR is enabled on an interface, all incoming packets are filtered based on the criteria defined in the route maps. For packets that match the filtering criteria, the precedence or Differentiated Services Code Point (DSCP) value can be changed, or the packets can be routed/forwarded to the appropriate next hop.
PBR and dynamic routing protocols, such as Border Gateway Protocol (BGP) and Open Shortest Path First (OSPF), use route maps. You can define a maximum of 255 route maps. Route maps used by a PBR policy cannot be used by a dynamic routing protocol. You can configure a maximum of 32 access list statements in a route map. You can assign only one route map to a non‐management IP interface.
You must define route map criteria using match and set commands. All sequential match clauses must be met by the packets for the set clauses to be applied. Match Clauses
IPv4 ACLs can be used to specify the match criteria. The following match criteria can be used in a PBR ACL:

Source IP

Destination IP

Protocol

ToS

TCP/UDP source port

TCP/UDP destination port
If criteria other than the above are used in a PBR ACL, the switch will display an error message.
If ingress packets do not meet any of the match criteria, or if a deny statement is configured in the ACL, then the packets are routed based on the entries in the routing table.
Set Clauses
When the match clause(s) is satisfied, one of the following set clauses can be used to specify the packet forwarding criteria:
© Copyright Lenovo 2016

Next hop IP address: This must be the IP address of an interface on the adjacent router. A remote router interface cannot be used to specify the next hop. Packets are forwarded to the next hop IP address. The PBR policy uses the next hops in the order you specify. If the first next hop is down, then the second next hop is used, and so on. If you specify the next hop addresses using separate statements, then the next hops are used in the order you specify, starting from top to down. A maximum of 64 unique next hops can be configured across all route maps. 
IP Differentiated Services Code Point (DSCP) value: A value used to set the DSCP value of the matching packets.
Chapter 22: Policy-Based Routing
353

IP precedence value: A value or keyword used to set the precedence value of the matching packets.
You can use a combination of set commands. However, you cannot use the set commands for DSCP and precedence together in the same route map.
Following are the basic steps and commands for configuring route maps.
1. Configure a route map. RS G8052(config)# route­map <route map number>
2. Define an access list statement and assign an ACL to the route map. RS G8052(config­route­map)# access­list <1‐32> match­access­control <IP ACL number>
3. Enable the access list. RS G8052(config­route­map)# access­list <1‐32> enable
4. Set next hop IP address i.e. IP address of an adjacent router. RS G8052(config­route­map)# set ip next­hop <IP address> [<nh2 IP address>] [<nh3 IP address>] [<nh4 IP address>] [access­list {<access list ID>|<access list range>}]
OR Set IP precedence value. RS G8052(config­route­map)# set ip precedence <value or keyword> [access­list {<access list ID>|<access list range>}]
OR Set IP DSCP value. RS G8052(config­route­map)# set ip dscp <value> [access­list {<access list ID>|<access list range>}]
5. Set next hop peer IP address. RS G8052(config­route­map)# set ip next­hop <peer IP address>
354
G8052 Application Guide for ENOS 8.4
Configuring Health Check
You can configure tracking/health check parameters for each of the next hop IP address you specify in the route map. By default, Address Resolution Protocol (ARP) resolves the next hop IP address. The ARP re‐try interval is two minutes. Use the following command to configure health check: RS G8052(config­route­map)# set ip next­hop verify­availability <next hop IP address> <priority> [icmp|arp] [interval] [retry] [access­list {<access list ID>|<access list range>}] Default values:
Protocol: ARP
Interval: 2 seconds
Retry: 3 times
You must configure a separate statement for verifying health check of each next hop. A maximum of four health check statements can be included in a route map.
Note: When you configure next hops using set ip next­hop command and health check using the set ip next­hop verify­availability command in the same route map, only the health check statements will be considered. Following is an example of a route map health check statement: RS G8052(config­route­map)# set ip next­hop verify­availability 12.1.1.1 10 icmp access­list 4
Similarly, if there are inconsistent tracking parameters for a particular next hop IP address among multiple route maps, the route map with the lowest route map number is considered.
Note: We strongly recommend that you configure health check if all or multiple next hops specified in the route map belong to the same Spanning Tree Group (STG). This is required in case of an STP topology change where all forwarding database (FDB) entries on all the ports in an STG are cleared. In such a scenario, the associated ARP entries are purged and the next hop specified in the PBR policy will not get resolved. When health check is configured, the PBR policy will route the traffic based on the second next hop that you have specified.
© Copyright Lenovo 2016
Chapter 22: Policy-Based Routing
355
Example PBR Configuration
Note: Use only the ISCLI to configure PBR. Configurations using the BBI are not supported.
Following is an example of configuring PBR to match packets with a destination network address of 3.0.0.0. The PBR is applied to ingress packets on the IP interface 11. The next hop IP address is configured as 5.5.5.5 or 10.10.10.10.
1. Configure an ACL and specify the match criteria. RS G8052(config)# access­control list 100 action permit
RS G8052(config)# access­control list 100 ipv4 destination­ip­address 3.0.0.0 255.0.0.0
2. Configure a route map. RS G8052(config)# route­map 126
3. Apply the ACL to the route map. RS G8052(config­route­map)# access­list 1 match­access­control 100
4. Set the next hop IP addresses. RS G8052(config­route­map)# set ip next­hop 5.5.5.5 10.10.10.10
RS G8052(config­route­map)# exit
5. Apply the route map to an IP interface that has a VLAN configured. RS
RS
RS
RS
G8052(config)# interface ip 11
G8052(config­ip­if)# ip policy route­map 126
G8052(config­ip­if)# exit
G8052(config)# exit
6. Verify PBR configuration. RS G8052# show ip policy
IP Interface Route map
11 126
RS G8052# show route­map 126
126: PBR, enabled
Match clauses:
alist 1: access­control list 100, enabled
Set clauses:
ip next­hop 5.5.5.5 10.10.10.10, alist all
Policy routing matches: 0 packets
356
G8052 Application Guide for ENOS 8.4
Configuring PBR with other Features
Consider the following PBR behavior when configured with the features given below:

DSCP: PBR ACLs can be used to remark an IP packet with a new precedence/DSCP value. PBR ACL remark statements have higher priority than the DSCP remark commands configured on ports.

Virtual Router Redundancy Protocol (VRRP): If PBR is enabled on a VRRP IP interface, the PBR becomes effective on the interface when the switch becomes the VRRP master on that IP interface.

Virtual Link Aggregation Group (VLAG): When configuring PBR on VLAG ports, you must configure the same PBR policy on both the VLAG peers. You cannot configure the next hop to be on a remote switch or on the VLAG ports.
Unsupported Features
PBR cannot be configured for:
© Copyright Lenovo 2016

Routed ports

Multicast traffic

IPv6 packets

Simple Network Management Protocol (SNMP)

Stacking

Virtual Network Interface Card (vNIC)

Loopback Interface
Chapter 22: Policy-Based Routing
357
358
G8052 Application Guide for ENOS 8.4
Chapter 23. Routed Ports
By default, all ports on the Lenovo RackSwitch G8052 behave as switch ports, which are capable of performing Layer 2 switch functions, such as VLANs, STP, or bridging. Switch ports also provide a physical point of access for the switch IP interfaces, which can perform global Layer 3 functions, such as routing for BGP or OSPF.
However, G8052 ports can also be configured as routed ports. Routed ports are configured with their own IP address belonging to a unique Layer 3 network, and behave similar to a port on a conventional router. Routed ports are typically used for connecting to a server or to a router.
When a switch port is configured as a routed port, it forwards Layer 3 traffic and no longer performs Layer 2 switching functions.
© Copyright Lenovo 2016
359
Overview
A routed port has the following characteristics:

Does not participate in bridging.

Does not belong to any user‐configurable VLAN.

Does not implement any Layer 2 functionality, such as Spanning Tree Protocol (STP).

Is always in a forwarding state.

Can participate in IPv4 routing.

Can be configured with basic IP protocols, such as Internet Control Message Protocol (ICMP), and with Layer 3 protocols, such as Protocol‐Independent Multicast (PIM), Routing Information Protocol (RIP), Open Shortest Path First (OSPF), and Border Gateway Protocol (BGP).

Can be configured with Internet Group Management Protocol (IGMP) querier and snooping functionality.

Layer 3 configuration is saved even when the interface is shutdown. 
MAC address learning is always enabled.

Tagging and port VLAN ID (PVID) tagging is disabled.

Flooding is disabled.

Bridge Protocol Data Unit (BPDU)‐guard is disabled.

Link Aggregation Control Protocol (LACP) is disabled.

Multicast threshold is disabled.

Static Multicast MAC and static unicast MAC can be configured.
Notes:

Ports on which LACP or portchannel is enabled cannot be changed to routed ports.

Ports that have Static MAC addresses configured cannot be changed to routed ports.
When a switch port is configured as a routed port, the following configuration changes are automatically implemented:

The port is removed from all the VLANs it belonged to.

The port is added to an internal VLAN on which flooding is disabled. The ID of this internal VLAN could be 4094 or lower. The internal VLAN is assigned to Spanning Tree Group (STG) 1, if RSTP/PVRST is configured; or to Common Internal Spanning Tree (CIST), if MSTP is configured. You cannot change the VLAN number assigned to the routed port. 
STP is disabled and the port is set to a forwarding state.
Note: The maximum number of VLANs you can configure on the RackSwitch G8052 is 2048. This maximum number will be reduced by the number of routed ports you configure.
360
G8052 Application Guide for ENOS 8.4

All the Layer 2 configuration is lost. When a routed port is changed back to a switch port, the following changes take place:

All the IP configuration is lost.

The ARP entry corresponding to the IP address is lost.

The switch port is added to the default VLAN and STG. In case of MSTP, it is added to the CIST.

STP is turned on.

The switch port can participate in STG and VLAN flooding.

Can participate in bridging.

LACP port attributes are set to default.

Multicast threshold remains disabled.

BPDU guard remains disabled.

IGMP configuration is lost.
Note: When you configure a routed port to back to a switch port, it does not restore the Layer 2 configuration it had before it was changed to a routed port.
© Copyright Lenovo 2016
Chapter 23: Routed Ports
361
Configuring a Routed Port
Note: Use only the ISCLI to configure routed ports. Configurations using the BBI are not supported. Configurations made using SNMP cannot be saved or applied.
Note: You cannot configure a management port to be a routed port.
Following are the basic steps for configuring a routed port:
1. Enter the interface configuration mode for the port. RS G8052(config)# interface port <port number>
Note: You must enter only one port number. If you need to change multiple ports to routed ports, repeat the configuration steps for each port.
2. Enable routing. RS G8052(config­if)# no switchport
3. Assign an IP address. RS G8052(config­if)# ip address <IP address> <Subnet Mask> enable
4. (Optional) Enable a Layer 3 routing protocol. RS G8052(config­if)# ip {<ospf>|<pim>|<rip>}
Note: Configure the Layer 3 routing protocol‐related parameters in the interface configuration mode.
Configuring OSPF on Routed Ports
The following OSPF configuration commands are supported on routed ports: RS G8052(config­if)# ip ospf ?
area Set area index
cost Set interface cost
dead­interval Set dead interval in seconds or milliseconds
enable Enable OSPF for this interface
hello­interval Set hello interval in seconds or milliseconds
key Set authentication key
message­digest­key Set MD5 key ID
passive­interface Enable passive interface
point­to­point Enable point­to­point interface
priority Set interface router priority
retransmit­interval Set retransmit interval in seconds
transit­delay Set transit delay in seconds
See Chapter 30, “Open Shortest Path First,” for details on the OSPF protocol and its configuration. OSPFv3 cannot be configured on routed ports.
362
G8052 Application Guide for ENOS 8.4
OSPF Configuration Example
The following example includes the basic steps for configuring OSPF on a routed port: RS G8052(config)# router ospf
RS G8052(config­router­ospf)# area 0 enable
RS G8052(config­router­ospf)# enable
RS G8052(config-router-ospf)# exit
RS G8052(config)# interface port 1
RS G8052(config­if)# no switchport
wait...
RS G8052(config­if)# ip address 11.1.12.1 255.255.255.0 enable
wait...
RS G8052(config­if)# ip ospf area 0
RS G8052(config­if)# ip ospf enable
RS G8052(config­if)# exit
Configuring RIP on Routed Ports
The following RIP configuration commands are supported on routed ports: RS G8052(config­if)# ip rip ?
authentication Set IP authentication
default­action Set default route action
enable Enable RIP interface
listen Enable listening to route updates
metric Set metric
multicast­updates Enable multicast updates
poison Enable poisoned reverse
split­horizon Enable split horizon
supply Enable supplying route updates
triggered Enable triggered updates
version RIP version
See Chapter 26, “Routing Information Protocol,” for details on the RIP protocol and its configuration. RIP Configuration Example
The following example includes steps for a basic RIP configuration on a routed port: RS G8052(config)# router rip
RS G8052(config­router­rip)# enable
RS G8052(config-router-rip)# exit
RS G8052(config)# interface port 1
RS G8052(config­if)# no switchport
wait...
RS G8052(config­if)# ip address 11.1.12.1 255.255.255.0 enable
wait...
RS G8052(config­if)# ip rip enable
RS G8052(config­if)# exit
© Copyright Lenovo 2016
Chapter 23: Routed Ports
363
Configuring PIM on Routed Ports
The following PIM configuration commands are supported on routed ports: RS G8052(config­if)# ip pim ?
border­bit Set interface as border interface
cbsr­preference Set preference for local interface as a candidate bootstrap router
component­id Add interface to the component
dr­priority Set designated router priority for the router interface
enable Enable PIM on this interface
hello­holdtime Set hello message holdtime for the interface
hello­interval Set the frequency of PIM hello messages on the interface
join­prune­interval Set frequency of PIM Join or Prune interval
lan­delay Set lan delay for the router interface
lan­prune­delay Enable lan delay advertisement on interface
neighbor­addr Neighbor address
neighbor­filter Enable neighbor filter
override­interval Set override interval for router interface
See Chapter 31, “Protocol Independent Multicast” for details on the PIM protocol and its configuration.
PIM Configuration Example
The following example includes the basic steps for configuring PIM on a routed port: RS G8052(config)# ip pim enable
RS G8052(config)# interface port 26
RS G8052(config­if)# no switchport
wait...
RS G8052(config­if)# ip address 26.26.26.1 255.255.255.0 enable
wait...
RS G8052(config­if)# ip pim enable
RS G8052(config­if)# exit
RS G8052(config)# ip pim component 1
RS G8052(config-ip-pim-component)# rp­candidate rp­address 224.0.0.0 240.0.0.0 26.26.26.1
RS G8052(config-ip-pim-component)# rp­candidate holdtime 200
RS G8052(config­ip­pim­component)# exit
RS G8052(config)# interface port 26
RS G8052(config­if)# ip pim cbsr­preference 200
RS G8052(config­if)# exit
Verify the configuration using the following command: RS G8052(config)# show ip pim interface port 26
Address IfName/IfId Ver/Mode Nbr Qry DR­Address DR­Prio
Count Interval
­­­­­­­ ­­­­­­­­­­­ ­­­­­­­­ ­­­­­ ­­­­­­­­ ­­­­­­­­­­ ­­­­­­­
26.26.26.1 Rport 26 2/Sparse 0 30 26.26.26.1 1 364
G8052 Application Guide for ENOS 8.4
Configuring BGP on Routed Ports
The routed port can be used to establish a TCP connection to form peer relationship with another BGP router. See Chapter 29, “Border Gateway Protocol,” for details on the BGP protocol and its configuration.
The following BGP configurations are not supported on routed ports:

Update source ‐ configuring a local IP interface
Configuring IGMP on Routed Ports
IGMP querier and snooping can be configured on routed ports. For details, see Chapter 27, “Internet Group Management Protocol.”
To configure IGMP snooping on a routed port, enter the following command in the Global Configuration mode: RS G8052(config)# ip igmp snoop port <routed port ID>
To configure fastleave on routed ports, enter the following command in the Global Configuration mode: RS G8052(config)# ip igmp fastleave port <routed port ID>
The following IGMP querier commands are supported on routed ports: RS G8052(config)# ip igmp querier port <routed port ID> ?
election­type Set IGMP querier type
enable Turn IGMP Querier on
max­response Set Queriers max response time
query­interval Set general query interval for IGMP Querier only
robustness Set IGMP robustness
source­ip Set source IP to be used for IGMP
startup­count Set startupcount for IGMP
startup­interval Set startup query interval for IGMP
version Sets the operating version of the IGMP snooping switch
© Copyright Lenovo 2016
Chapter 23: Routed Ports
365
Limitations
Following features/configurations are not supported on routed ports:
366

Subinterfaces

BPDU Guard

Broadcast Threshold

Multicast Threshold

Link Aggregation Control Protocol (LACP)

Static Aggregation

Fibre Channel over Ethernet (FCoE)

IPv6

IP Security (IPsec)

Internet Key Exchange version 2 (IKEv2)

Virtual Router Redundancy Protocol (VRRP)

Policy‐based Routing (PBR)

Hotlinks

Failover

802.1X

Dynamic Host Configuration Protocol (DHCP)

BOOTP

Simple Network Management Protocol (SNMP)

IGMP Relay

Static Multicast Routes

Static Mrouter Port
G8052 Application Guide for ENOS 8.4
Chapter 24. Internet Protocol Version 6
Internet Protocol version 6 (IPv6) is a network layer protocol intended to expand the network address space. IPv6 is a robust and expandable protocol that meets the need for increased physical address space. The switch supports the following RFCs for IPv6‐related features:










RFC 1981
RFC 2404
RFC 2410
RFC 2451
RFC 2460
RFC 2474
RFC 2526
RFC 2711
RFC 2740
RFC 3289










RFC 3306
RFC 3307
RFC 3411
RFC 3412
RFC 3413
RFC 3414
RFC 3484
RFC 3602
RFC 3810
RFC 3879










RFC 4007
RFC 4213
RFC 4291
RFC 4292
RFC 4293
RFC 4301
RFC 4302
RFC 4303
RFC 4306
RFC 4307









RFC 4443
RFC 4552
RFC 4718
RFC 4835
RFC 4861
RFC 4862
RFC 5095
RFC 5114
RFC 5340
This chapter describes the basic configuration of IPv6 addresses and how to manage the switch via IPv6 host management.
© Copyright Lenovo 2016
367
IPv6 Limitations
The following IPv6 features are not supported in this release: Dynamic Host Control Protocol for IPv6 (DHCPv6)
Border Gateway Protocol for IPv6 (BGP)
 Routing Information Protocol for IPv6 (RIPng)


Most other Lenovo Enterprise Network Operating System 8.4 features permit IP addresses to be configured using either IPv4 or IPv6 address formats. However, the following switch features support IPv4 only:








368
Bootstrap Protocol (BOOTP) and DHCP
RADIUS, TACACS+ and LDAP
Stacking
VMware Virtual Center (vCenter) for VMready
Routing Information Protocol (RIP)
Border Gateway Protocol (BGP)
Virtual Router Redundancy Protocol (VRRP)
sFlow
G8052 Application Guide for ENOS 8.4
IPv6 Address Format
The IPv6 address is 128 bits (16 bytes) long and is represented as a sequence of eight 16‐bit hex values, separated by colons. Each IPv6 address has two parts: 
Subnet prefix representing the network to which the interface is connected 
Local identifier, either derived from the MAC address or user‐configured
The preferred hexadecimal format is as follows: xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx
Example IPv6 address: FEDC:BA98:7654:BA98:FEDC:1234:ABCD:5412
Some addresses can contain long sequences of zeros. A single contiguous sequence of zeros can be compressed to :: (two colons). For example, consider the following IPv6 address:
FE80:0:0:0:2AA:FF:FA:4CA2 The address can be compressed as follows:
FE80::2AA:FF:FA:4CA2 Unlike IPv4, a subnet mask is not used for IPv6 addresses. IPv6 uses the subnet prefix as the network identifier. The prefix is the part of the address that indicates the bits that have fixed values or are the bits of the subnet prefix. An IPv6 prefix is written in address/prefix‐length notation. For example, in the following address, 64 is the network prefix:
21DA:D300:0000:2F3C::/64 IPv6 addresses can be either user‐configured or automatically configured. Automatically configured addresses always have a 64‐bit subnet prefix and a 64‐bit interface identifier. In most implementations, the interface identifier is derived from the switchʹs MAC address, using a method called EUI‐64.
Most Enterprise NOS 8.4 features permit IP addresses to be configured using either IPv4 or IPv6 address formats. Throughout this manual, IP address is used in places where either an IPv4 or IPv6 address is allowed. In places where only one type of address is allowed, the type (IPv4 or IPv6) is specified.
© Copyright Lenovo 2016
Chapter 24: Internet Protocol Version 6
369
IPv6 Address Types
IPv6 supports three types of addresses: unicast (one‐to‐one), multicast (one‐to‐many), and anycast (one‐to‐nearest). Multicast addresses replace the use of broadcast addresses. Unicast Address
Unicast is a communication between a single host and a single receiver. Packets sent to a unicast address are delivered to the interface identified by that address. IPv6 defines the following types of unicast address: 
Global Unicast address: An address that can be reached and identified globally. Global Unicast addresses use the high‐order bit range up to FF00, therefore all non‐multicast and non‐link‐local addresses are considered to be global unicast. A manually configured IPv6 address must be fully specified. Autoconfigured IPv6 addresses are comprised of a prefix combined with the 64‐bit EUI. RFC 4291 defines the IPv6 addressing architecture. The interface ID must be unique within the same subnet.

Link‐local unicast address: An address used to communicate with a neighbor on the same link. Link‐local addresses use the format FE80::EUI
Link‐local addresses are designed to be used for addressing on a single link for purposes such as automatic address configuration, neighbor discovery, or when no routers are present.
Routers must not forward any packets with link‐local source or destination addresses to other links.
Multicast
Multicast is communication between a single host and multiple receivers. Packets are sent to all interfaces identified by that address. An interface may belong to any number of multicast groups. A multicast address (FF00 ‐ FFFF) is an identifier for a group interface. The multicast address most often encountered is a solicited‐node multicast address using prefix FF02::1:FF00:0000/104 with the low‐order 24 bits of the unicast or anycast address.
The following well‐known multicast addresses are pre‐defined. The group IDs defined in this section are defined for explicit scope values, as follows:
FF00:::::::0 through FF0F:::::::0 Anycast
Packets sent to an anycast address or list of addresses are delivered to the nearest interface identified by that address. Anycast is a communication between a single sender and a list of addresses. Anycast addresses are allocated from the unicast address space, using any of the defined unicast address formats. Thus, anycast addresses are syntactically indistinguishable from unicast addresses. When a unicast address is assigned to 370
G8052 Application Guide for ENOS 8.4
more than one interface, thus turning it into an anycast address, the nodes to which the address is assigned must be explicitly configured to know that it is an anycast address. © Copyright Lenovo 2016
Chapter 24: Internet Protocol Version 6
371
IPv6 Address Autoconfiguration
IPv6 supports the following types of address autoconfiguration: 
Stateful address configuration
Address configuration is based on the use of a stateful address configuration protocol, such as DHCPv6, to obtain addresses and other configuration options.

Stateless address configuration
Address configuration is based on the receipt of Router Advertisement messages that contain one or more Prefix Information options. ENOS 8.4 supports stateless address configuration. Stateless address configuration allows hosts on a link to configure themselves with link‐local addresses and with addresses derived from prefixes advertised by local routers. Even if no router is present, hosts on the same link can configure themselves with link‐local addresses and communicate without manual configuration.
372
G8052 Application Guide for ENOS 8.4
IPv6 Interfaces
Each IPv6 interface supports multiple IPv6 addresses. You can manually configure up to two IPv6 addresses for each interface, or you can allow the switch to use stateless autoconfiguration.
You can manually configure two IPv6 addresses for each interface, as follows: 
Initial IPv6 address is a global unicast or anycast address.
RS G8052(config)# interface ip <interface number>
RS G8052(config­ip­if)# ipv6 address <IPv6 address>
Note that you cannot configure both addresses as anycast. If you configure an anycast address on the interface you must also configure a global unicast address on that interface.

Second IPv6 address can be a unicast or anycast address.
RS G8052(config­ip­if)# ipv6 secaddr6 <IPv6 address>
RS G8052(config­ip­if)# exit
You cannot configure an IPv4 address on an IPv6 management interface. Each interface can be configured with only one address type: either IPv4 or IPv6, but not both. When changing between IPv4 and IPv6 address formats, the prior address settings for the interface are discarded.
Each IPv6 interface can belong to only one VLAN. Each VLAN can support only one IPv6 interface. Each VLAN can support multiple IPv4 interfaces. Use the following commands to configure the IPv6 gateway: RS G8052(config)# ip gateway6 1 address <IPv6 address>
RS G8052(config)# ip gateway6 1 enable
IPv6 gateway 1 is reserved for IPv6 data interfaces.
© Copyright Lenovo 2016
Chapter 24: Internet Protocol Version 6
373
Neighbor Discovery
The switch uses Neighbor Discovery protocol (ND) to gather information about other router and host nodes, including the IPv6 addresses. Host nodes use ND to configure their interfaces and perform health detection. ND allows each node to determine the link‐layer addresses of neighboring nodes and to keep track of each neighbor’s information. A neighboring node is a host or a router linked directly to the switch. The switch supports Neighbor Discovery as described in RFC 4861. Neighbor Discovery Overview
Neighbor Discover messages allow network nodes to exchange information, as follows: 
Neighbor Solicitations allow a node to discover information about other nodes. 
Neighbor Advertisements are sent in response to Neighbor Solicitations. The Neighbor Advertisement contains information required by nodes to determine the link‐layer address of the sender, and the sender’s role on the network. 
IPv6 hosts use Router Solicitations to discover IPv6 routers. When a router receives a Router Solicitation, it responds immediately to the host.

Routers uses Router Advertisements to announce its presence on the network, and to provide its address prefix to neighbor devices. IPv6 hosts listen for Router Advertisements, and uses the information to build a list of default routers. Each host uses this information to perform autoconfiguration of IPv6 addresses. 
Redirect messages are sent by IPv6 routers to inform hosts of a better first‐hop address for a specific destination. Redirect messages are only sent by routers for unicast traffic, are only unicast to originating hosts, and are only processed by hosts.
ND configuration for general advertisements, flags, and interval settings, as well as for defining prefix profiles for router advertisements, is performed on a per‐interface basis using the following commands: RS G8052(config)# interface ip <interface number>
RS G8052(config­ip­if)# [no] ipv6 nd ?
RS G8052(config­ip­if)# exit
To add or remove entries in the static neighbor cache, use the following command:
RS G8052(config)# [no] ip neighbors ?
To view the neighbor cache table, use the following command:
RS G8052(config)# show ipv6 neighbors ?
To view the neighbor cache counters, use the following command:
RS G8052(config)# show ipv6 neighbors counters
374
G8052 Application Guide for ENOS 8.4
To clear the neighbor cache counters, use the following command:
RS G8052(config)# clear ipv6 neighbors counters
Host vs. Router
Each IPv6 interface can be configured as a router node or a host node, as follows: 
A router node’s IP address is configured manually. Router nodes can send Router Advertisements. 
A host node’s IP address can be autoconfigured. Host nodes listen for Router Advertisements that convey information about devices on the network. Note: When IP forwarding is turned on, all IPv6 interfaces configured on the switch can forward packets.
You can configure each IPv6 interface as either a host node or a router node. You can manually assign an IPv6 address to an interface in host mode, or the interface can be assigned an IPv6 address by an upstream router, using information from router advertisements to perform stateless auto‐configuration. To set an interface to host mode, use the following command:
RS G8052(config)# interface ip <interface number>
RS G8052(config­ip­if)# ip6host
RS G8052(config­ip­if)# exit
The G8052 supports up to 1156 IPv6 routes.
© Copyright Lenovo 2016
Chapter 24: Internet Protocol Version 6
375
Supported Applications
The following applications have been enhanced to provide IPv6 support. 
Ping
The ping command supports IPv6 addresses. Use the following format to ping an IPv6 address: ping <host name>|<IPv6 address> [­n <tries (0‐4294967295)>] [­w <msec delay (0‐4294967295)>] [­l <length (0/32‐65500/2080)>] [­s <IP source>] [­v <TOS (0‐255)>] [­f] [­t]
To ping a link‐local address (begins with FE80), provide an interface index, as follows: ping <IPv6 address>%<Interface index> [­n <tries (0‐4294967295)>] [­w <msec delay (0‐4294967295)>] [­l <length (0/32‐65500/2080)>] [­s <IP source>] [­v <TOS (0‐255)>] [­f] [­t]

Traceroute
The traceroute command supports IPv6 addresses (but not link‐local addresses). Use the following format to perform a traceroute to an IPv6 address: traceroute <host name>| <IPv6 address> [<max‐hops (1‐32)> [<msec delay (1‐4294967295)>]] 
Telnet server
The telnet command supports IPv6 addresses (but not link‐local addresses). Use the following format to Telnet into an IPv6 interface on the switch: telnet <host name>| <IPv6 address> [<port>] 
Telnet client
The telnet command supports IPv6 addresses (but not link‐local addresses). Use the following format to Telnet to an IPv6 address: telnet <host name>| <IPv6 address> [<port>] 
HTTP/HTTPS
The HTTP/HTTPS servers support both IPv4 and IPv6 connections. 
SSH
Secure Shell (SSH) connections over IPv6 are supported (but not link‐local addresses). The following syntax is required from the client: ssh ­u <IPv6 address>
Example: ssh ­u 2001:2:3:4:0:0:0:142

TFTP
The TFTP commands support both IPv4 and IPv6 addresses. Link‐local addresses are not supported. 
FTP
The FTP commands support both IPv4 and IPv6 addresses. Link‐local addresses are not supported. 376
G8052 Application Guide for ENOS 8.4

DNS client
DNS commands support both IPv4 and IPv6 addresses. Link‐local addresses are not supported. Use the following command to specify the type of DNS query to be sent first:
RS G8052(config)# ip dns ipv6 request­version {ipv4|ipv6}
If you set the request version to ipv4, the DNS application sends an A query first, to resolve the hostname with an IPv4 address. If no A record is found for that hostname (no IPv4 address for that hostname) an AAAA query is sent to resolve the hostname with a IPv6 address. If you set the request version to ipv6, the DNS application sends an AAAA query first, to resolve the hostname with an IPv6 address. If no AAAA record is found for that hostname (no IPv6 address for that hostname) an A query is sent to resolve the hostname with an IPv4 address. Configuration Guidelines
When you configure an interface for IPv6, consider the following guidelines: © Copyright Lenovo 2016

Support for subnet router anycast addresses is not available. 
A single interface can accept either IPv4 or IPv6 addresses, but not both IPv4 and IPv6 addresses. 
A single interface can accept multiple IPv6 addresses. 
A single interface can accept only one IPv4 address. 
If you change the IPv6 address of a configured interface to an IPv4 address, all IPv6 settings are deleted. 
A single VLAN can support only one IPv6 interface. 
Health checks are not supported for IPv6 gateways. 
IPv6 interfaces support Path MTU Discovery. The CPU’s MTU is fixed at 1500 bytes. 
Support for jumbo frames (1,500 to 9,216 byte MTUs) is limited. Any jumbo frames intended for the CPU must be fragmented by the remote node. The switch can re‐assemble fragmented packets up to 9k. It can also fragment and transmit jumbo packets received from higher layers.
Chapter 24: Internet Protocol Version 6
377
IPv6 Configuration Examples
This section provides steps to configure IPv6 on the switch.
IPv6 Example 1
The following example uses IPv6 host mode to autoconfigure an IPv6 address for the interface. By default, the interface is assigned to VLAN 1.
1. Enable IPv6 host mode on an interface. RS
RS
RS
RS
G8052(config)# interface ip 2
G8052(config­ip­if)# ip6host
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
2. Configure the IPv6 default gateway. RS G8052(config)# ip gateway6 1 address 2001:BA98:7654:BA98:FEDC:1234:ABCD:5412
RS G8052(config)# ip gateway6 1 enable
3. Verify the interface address. RS G8052(config)# show interface ip 2
IPv6 Example 2
Use the following example to manually configure IPv6 on an interface. 1. Assign an IPv6 address and prefix length to the interface. RS G8052(config)# interface ip 3
RS G8052(config­ip­if)# ipv6 address 2001:BA98:7654:BA98:FEDC:1234:ABCD:5214
RS G8052(config­ip­if)# ipv6 prefixlen 64
RS G8052(config­ip­if)# ipv6 seccaddr6 2003::1 32
RS G8052(config­ip­if)# vlan 2
RS G8052(config­ip­if)# enable
RS G8052(config­ip­if)# exit
The secondary IPv6 address is compressed, and the prefix length is 32. 2. Configure the IPv6 default gateway. RS G8052(config)# ip gateway6 1 address 2001:BA98:7654:BA98:FEDC:1234:ABCD:5412
RS G8052(config)# ip gateway6 1 enable
3. Configure router advertisements for the interface (optional) RS G8052(config)# interface ip 3
RS G8052(config­ip­if)# no ipv6 nd suppress­ra
378
G8052 Application Guide for ENOS 8.4
4. Verify the configuration.
RS G8052(config­ip­if)# show layer3
© Copyright Lenovo 2016
Chapter 24: Internet Protocol Version 6
379
380
G8052 Application Guide for ENOS 8.4
Chapter 25. IPsec with IPv6
Internet Protocol Security (IPsec) is a protocol suite for securing Internet Protocol (IP) communications by authenticating and encrypting each IP packet of a communication session. IPsec also includes protocols for establishing mutual authentication between agents at the beginning of the session and negotiation of cryptographic keys to be used during the session.
Since IPsec was implemented in conjunction with IPv6, all implementations of IPv6 must contain IPsec. To support the National Institute of Standards and Technology (NIST) recommendations for IPv6 implementations, Lenovo Enterprise Network Operating System IPv6 feature compliance has been extended to include the following IETF RFCs, with an emphasis on IP Security (IPsec), Internet Key Exchange version 2, and authentication/confidentiality for OSPFv3:

RFC 4301 for IPv6 security

RFC 4302 for the IPv6 Authentication Header

RFCs 2404, 2410, 2451, 3602, and 4303 for IPv6 Encapsulating Security Payload (ESP), including NULL encryption, CBC‐mode 3DES and AES ciphers, and HMAC‐SHA‐1‐96.

RFCs 4306, 4307, 4718, and 4835 for IKEv2 and cryptography

RFC 4552 for OSPFv3 IPv6 authentication

RFC 5114 for Diffie‐Hellman groups
Note: This implementation of IPsec supports DH groups 1, 2, 5, 14, and 24.
The following topics are discussed in this chapter:
© Copyright Lenovo 2016

“IPsec Protocols” on page 382 
“Using IPsec with the Lenovo RackSwitch G8052” on page 383
Chapter 25: IPsec with IPv6
381
IPsec Protocols
The Enterprise NOS implementation of IPsec supports the following protocols:

Authentication Header (AH)
AHs provide connectionless integrity out and data origin authentication for IP packets. They also provide protection against replay attacks. In IPv6, the AH protects the AH itself, the Destination Options extension header after the AH, and the IP payload. It also protects the fixed IPv6 header and all extension headers before the AH, except for the mutable fields DSCP, ECN, Flow Label, and Hop Limit. AH is defined in RFC 4302.

Encapsulating Security Payload (ESP)
ESPs provide confidentiality, data origin authentication, integrity, an anti‐replay service (a form of partial sequence integrity), and some traffic flow confidentiality. ESPs may be applied alone or in combination with an AH. ESP is defined in RFC 4303.

Internet Key Exchange Version 2 (IKEv2)
IKEv2 is used for mutual authentication between two network elements. An IKE establishes a security association (SA) that includes shared secret information to efficiently establish SAs for ESPs and AHs, and a set of cryptographic algorithms to be used by the SAs to protect the associated traffic. IKEv2 is defined in RFC 4306.
Using IKEv2 as the foundation, IPsec supports ESP for encryption and/or authentication, and/or AH for authentication of the remote partner.
Both ESP and AH rely on security associations. A security association (SA) is the bundle of algorithms and parameters (such as keys) that encrypt and authenticate a particular flow in one direction.
382
G8052 Application Guide for ENOS 8.4
Using IPsec with the Lenovo RackSwitch G8052
IPsec supports the fragmentation and reassembly of IP packets that occurs when data goes to and comes from an external device. The Lenovo RackSwitch G8052 acts as an end node that processes any fragmentation and reassembly of packets but does not forward the IPsec traffic. :You must authenticate the IKEv2 key following the directions in “Setting up Authentication” on page 383 before you can use IPsec.
The security protocol for the session key is either ESP or AH. Outgoing packets are labeled with the SA SPI (Security Parameter Index), which the remote device will use in its verification and decryption process. Every outgoing IPv6 packet is checked against the IPsec policies in force. For each outbound packet, after the packet is encrypted, the software compares the packet size with the MTU size that it either obtains from the default minimum maximum transmission unit (MTU) size (1500) or from path MTU discovery. If the packet size is larger than the MTU size, the receiver drops the packet and sends a message containing the MTU size to the sender. The sender then fragments the packet into smaller pieces and retransmits them using the correct MTU size.
The maximum traffic load for each IPsec packet is limited to the following:

IKEv2 SAs: 5

IPsec SAs: 10 (5 SAs in each direction)

SPDs: 20 (10 policies in each direction)
IPsec is implemented as a software cryptography engine designed for handling control traffic, such as network management. IPsec is not designed for handling data traffic, such as a VPN.
Setting up Authentication
Before you can use IPsec, you need to have key policy authentication in place. There are two types of key policy authentication:

Preshared key (default)
The parties agree on a shared, secret key that is used for authentication in an IPsec policy. During security negotiation, information is encrypted before transmission by using a session key created by using a Diffie‐Hellman calculation and the shared, secret key. Information is decrypted on the receiving end using the same key. One IPsec peer authenticates the other peerʹs packet by decryption and verification of the hash inside the packet (the hash inside the packet is a hash of the preshared key). If authentication fails, the packet is discarded.

Digital certificate (using RSA algorithms)
The peer being validated must hold a digital certificate signed by a trusted Certificate Authority and the private key for that digital certificate. The side performing the authentication only needs a copy of the trusted certificate authorities digital certificate. During IKEv2 authentication, the side being validated sends a copy of the digital certificate and a hash value signed using the private key. The certificate can be either generated or imported.
© Copyright Lenovo 2016
Chapter 25: IPsec with IPv6
383
Note: During the IKEv2 negotiation phase, the digital certificate takes precedence over the preshared key.
Creating an IKEv2 Proposal
With IKEv2, a single policy can have multiple encryption and authentication types, as well as multiple integrity algorithms.
To create an IKEv2 proposal:
1. Enter IKEv2 proposal mode.
RS G8052(config)# ikev2 proposal
2. Set the DES encryption algorithm.
RS G8052(config-ikev2-prop)# encryption 3des|aes­cbc (default: 3des)
3. Set the authentication integrity algorithm type.
RS G8052(config­ikev2­prop)# integrity sha1 (default: sha1)
4. Set the Diffie‐Hellman group.
RS G8052(config-ikev2-prop)# group 1|2|5|14|24 (default: 24)
Importing an IKEv2 Digital Certificate
To import an IKEv2 digital certificate for authentication:
1. Import the CA certificate file. RS G8052(config)# copy tftp ca­cert address <hostname or IPv4 address>
Source file name: <path and filename of CA certificate file>
Confirm download operation [y/n]: y
2. Import the host key file. RS G8052(config)# copy tftp host­key address <hostname or IPv4 address>
Source file name: <path and filename of host private key file>
Confirm download operation [y/n]: y
3. Import the host certificate file. RS G8052(config)# copy tftp host­cert address <hostname or IPv4 address>
Source file name: <path and filename of host certificate file>
Confirm download operation [y/n]: y
Generating a Certificate Signing Request
Before a digital certificate can be signed by a Certificate Authority (CA), it needs to be created. The generation of a certificate involves creating a Certificate Signing Request (CSR). The CSR includes various information related to the device and a 384
G8052 Application Guide for ENOS 8.4
public key. The public key is included in the CSR file itself and the private key associated with the public key is generated separately and kept private. The CSR can then be exported to a remote device to be signed by a CA.
1. Create an HTTPS CSR defining the information you want to be used in the various fields: RS G8052(config)# access https generate­csr
Country Name (2 letter code) []: <country code>
State or Province Name (full name) []: <state>
Locality Name (eg, city) []: <city>
Organization Name (eg, company) []: <company>
Organizational Unit Name (eg, section) []: <org. unit>
Common Name (eg, YOUR name) []: <name>
Email (eg, email address) []: <email address>
Confirm Generate CSR? [y/n]: y
..............................................+++
..............+++
Cert Req generated successfully
© Copyright Lenovo 2016
Chapter 25: IPsec with IPv6
385
2. To verify the CSR you can use the following command:
show https host­csr [pem­format|txt­format] RS G8052> show https host­csr txt­format
Certificate Request:
Data:
Version: 0 (0x0)
Subject: C=US, ST=Cali, L=Santa Barbara, O=Lenovo, OU=Sales, CN=www.zagat.com
Subject Public Key Info:
Public Key Algorithm: rsaEncryption
RSA Public Key: (2048 bit)
Modulus (2048 bit):
00:b5:05:f6:d5:ad:ab:f2:1d:a9:57:c4:bc:84:1b:
c6:bc:cd:04:95:ea:ad:ec:4a:44:3a:6e:42:9f:39:
96:14:11:a7:8e:3e:6f:da:9a:42:c6:c4:62:a1:33:
0e:a8:d3:6a:21:ce:f3:3c:4f:c1:8d:d1:e7:9e:c7:
29:04:ea:c6:7d:54:9a:4e:10:24:10:38:45:c6:4b:
13:19:f2:dd:8a:83:3f:5c:cf:8b:85:a7:2a:b0:eb:
7a:26:1f:4c:94:47:01:81:6a:59:d5:f5:d6:7e:3b:
b5:bc:e4:3f:6d:dd:84:15:07:61:93:e0:d1:40:f8:
9d:15:d0:a6:e1:9b:a4:ab:85:b5:2b:f0:56:e9:ef:
36:43:2b:aa:be:1b:63:3c:fd:74:ab:78:76:53:12:
e6:65:4c:0d:07:91:df:b3:91:96:f4:55:f7:37:73:
8c:f6:77:d7:9d:2b:a5:bd:17:3f:11:f2:85:4b:d6:
b4:1d:3f:70:1f:13:bb:5e:2e:4c:a8:ad:6a:7f:11:
36:97:a6:25:0a:87:66:31:c9:92:59:03:31:5d:ff:
df:c6:aa:93:7c:51:9f:8e:1b:6f:2a:be:c4:4c:66:
d6:2c:4b:6d:e6:ae:4e:02:82:fc:fa:a1:de:3b:c9:
24:25:d5:6e:15:15:18:ce:9b:a6:98:ad:0c:32:1f:
94:01
Exponent: 65537 (0x10001)
Attributes:
a0:00
Signature Algorithm: sha256WithRSAEncryption
24:26:dd:96:49:47:9d:78:74:48:9b:63:4c:32:f0:78:da:7d:
82:c9:17:6d:7e:93:38:60:94:d5:02:c1:31:dc:42:69:f5:57:
46:a8:44:5a:99:ea:55:d3:99:bf:f0:48:3b:ef:60:fd:50:e6:
33:cd:89:86:d3:51:97:f2:d1:68:6f:88:8c:e7:0f:3e:19:2a:
f4:ea:6b:dc:05:24:d7:98:cd:a3:d3:c3:ef:03:93:8b:3f:fe:
75:5e:67:f1:48:b6:20:a6:ff:ae:5a:25:41:7f:e4:c8:48:d4:
63:37:16:98:9e:2d:1b:b6:65:7a:0d:90:87:07:19:f0:02:17:
3a:3e:fd:f0:40:3e:a4:0f:53:97:9b:d5:18:22:78:f3:07:94:
63:be:f9:f2:5c:23:6d:0f:22:d1:17:db:38:24:5c:6b:7b:e0:
41:a6:51:28:30:2c:f4:1d:62:6c:06:f2:4c:0c:5b:79:51:13:
73:f8:88:ba:2e:05:98:5d:41:5e:9d:58:b1:0c:8f:fc:f2:79:
d5:30:7c:95:e9:ff:9a:cc:dd:d9:4c:2e:98:32:5a:ab:cd:59:
a4:37:a5:38:03:4e:e7:27:dc:14:c8:75:9d:ca:e0:62:37:02:
19:17:16:e3:92:c0:c3:16:13:26:c9:40:d7:ec:f2:8c:8e:fc:
1a:dc:27:4c
386
G8052 Application Guide for ENOS 8.4
RS G8052> show https host­csr pem­format
­­­­­BEGIN CERTIFICATE REQUEST­­­­­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­­­­­END CERTIFICATE REQUEST­­­­­
3. Export the CSR file to an external server: RS G8052(config)# copy cert­request tftp
Port type ["DATA"/"MGT"/"EXTM"]: <port type>
Address or name of remote host: <hostname or IPv4 address>
Destination file name: <path and filename on the remote server>
Certificate request successfully tftp'd to...
4. Import the signed certificate from an external server: RS G8052(config)# copy sftp host­cert­only mgt­port Address or name of remote host: 10.241.3.32
Enter SFTP server port [22]: Source file name: mars.crt
User name: admin
Password: Confirm download operation (y/n) ? y
Connecting to 10.241.3.32...via port 22
SFTP: User platformlinux logged in.
Download in progress
SFTP: Read 985 bytes
Certificate file download complete (985 bytes)
Restart the HTTPS server manually to make the switch use the certificate
5. Reset HTTPS server. RS G8052(config)# no access https enable
access https enable Generating certificate. Please wait (approx 30 seconds)
© Copyright Lenovo 2016
Chapter 25: IPsec with IPv6
387
Generating an IKEv2 Digital Certificate
To create an IKEv2 digital certificate for authentication:
1. Create an HTTPS certificate defining the information you want to be used in the various fields. RS G8052(config)# access https generate­certificate
Country Name (2 letter code) [US]:
State or Province Name (full name) [CA]:
Locality Name (eg, city) [Santa Clara]:
Organization Name (eg, company) [Lenovo]:
Organizational Unit Name (eg, section) [Engineering]:
Common Name (eg, YOUR name) [10.240.226.241]:
Email (eg, email address) []:
Confirm generat‘eywing certificate? [y/n]: y
Generating certificate. Please wait (approx 30 seconds)
restarting SSL agent
2. Save the HTTPS certificate.
The certificate is valid only until the switch is rebooted. To save the certificate so that it is retained beyond reboot or power cycles, use the following command: RS G8052(config)# access https save­certificate
3. Enable IKEv2 RSA‐signature authentication: RS G8052(config)# access https enable
Enabling IKEv2 Preshared Key Authentication
To set up IKEv2 preshared key authentication:
1. Enter the local preshared key. RS G8052(config)# ikev2 preshare­key local <preshared key, a string of 1‐256 chars>
2. If asymmetric authentication is supported, enter the remote key: RS G8052(config)# ikev2 preshare­key remote <preshared key> <IPv6 host>
where the following parameters are used:

preshared key
A string of 1‐256 characters

IPv6 host
An IPv6‐format host, such as “3000::1”
3. Set up the IKEv2 identification type by entering one of the following commands:
RS G8052(config)# ikev2 identity local address (use an IPv6 address)
RS G8052(config)# ikev2 identity local email <email address>
RS G8052(config)# ikev2 identity local fqdn <domain name>
To disable IKEv2 RSA‐signature authentication method and enable preshared key authentication, enter: RS G8052(config)# access https disable
388
G8052 Application Guide for ENOS 8.4
Setting Up a Key Policy
When configuring IPsec, you must define a key policy. This key policy can be either manual or dynamic. Either way, configuring a policy involves the following steps:

Create a transform set—This defines which encryption and authentication algo‐
rithms are used.

Create a traffic selector—This describes the packets to which the policy applies.

Establish an IPsec policy.

Apply the policy.
1. To define which encryption and authentication algorithms are used, create a transform set: RS G8052(config)# ipsec transform­set <transform ID> <encryption method> <integrity algorithm> <AH authentication algorithm> where the following parameters are used:

transform ID
A number from 1‐10

encryption method
One of the following: esp­3des | esp­aes­cbc | esp­null

integrity algorithm
One of the following: esp­sha1 | none

AH authentication algorithm
One of the following: ah­sha1 | ah­md5 | none
2. Decide whether to use tunnel or transport mode. The default mode is transport. RS G8052(config)# ipsec transform­set tunnel|transport
3. To describe the packets to which this policy applies, create a traffic selector using the following command: RS G8052(config)# ipsec traffic­selector <traffic selector number> permit|deny any|icmp <type|any> |tcp > <source IP address|any> <destination IP address|any> [<prefix length>]
where the following parameters are used:
© Copyright Lenovo 2016

traffic selector number
an integer from 1‐10

permit|deny
whether or not to permit IPsec encryption of traffic that meets the criteria specified in this command

any
apply the selector to any type of traffic

icmp <type>|any
only apply the selector only to ICMP traffic of the specified type (an integer from 1‐255) or to any ICMP traffic

tcp
only apply the selector to TCP traffic

source IP address|any
the source IP address in IPv6 format or “any” source
Chapter 25: IPsec with IPv6
389

destination IP address|any
the destination IP address in IPv6 format or “any” destination

prefix length
(Optional) the length of the destination IPv6 prefix; an integer from 1‐128
Permitted traffic that matches the policy in force is encrypted, while denied traffic that matches the policy in force is dropped. Traffic that does not match the policy bypasses IPsec and passes through clear (unencrypted).
4. Choose whether to use a manual or a dynamic policy. Using a Manual Key Policy
A manual policy involves configuring policy and manual SA entries for local and remote peers.
To configure a manual key policy, you need:


The IP address of the peer in IPv6 format (for example, “3000::1”).
Inbound/Outbound session keys for the security protocols.
You can then assign the policy to an interface. The peer represents the other end of the security association. The security protocol for the session key can be either ESP or AH.
To create and configure a manual policy:
1. Enter a manual policy to configure. RS G8052(config)#ipsec manual­policy <policy number>
2. Configure the policy. RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config­ipsec­manual)#peer <peer’s IPv6 address>
G8052(config­ipsec­manual)#traffic­selector <IPsec traffic selector>
G8052(config­ipsec­manual)#transform­set <IPsec transform set>
G8052(config­ipsec­manual)#in­ah auth­key <inbound AH IPsec key>
G8052(config­ipsec­manual)#in­ah auth­spi <inbound AH IPsec SPI>
G8052(config­ipsec­manual)#in­esp cipher­key <inbound ESP cipher key>
G8052(config­ipsec­manual)#in­esp auth­spi <inbound ESP SPI>
G8052(config­ipsec­manual)#in­esp auth­key <inbound ESP authenticator key>
G8052(config­ipsec­manual)#out­ah auth­key <outbound AH IPsec key>
G8052(config­ipsec­manual)#out­ah auth­spi <outbound AH IPsec SPI>
G8052(config­ipsec­manual)#out­esp cipher­key <outbound ESP cipher key>
G8052(config­ipsec­manual)#out­esp auth­spi <outbound ESP SPI>
G8052(config­ipsec­manual)#out­esp auth­key <outbound ESP authenticator key>
where the following parameters are used:
390

peer’s IPv6 address
The IPv6 address of the peer (for example, 3000::1)

IPsec traffic‐selector
A number from1‐10

IPsec of transform‐set
A number from1‐10

inbound AH IPsec key
The inbound AH key code, in hexadecimal

inbound AH IPsec SPI
A number from 256‐4294967295
G8052 Application Guide for ENOS 8.4

inbound ESP cipher key
The inbound ESP key code, in hexadecimal

inbound ESP SPI
A number from 256‐4294967295

inbound ESP authenticator key The inbound ESP authenticator key code, in hexadecimal

outbound AH IPsec key
The outbound AH key code, in hexadecimal

outbound AH IPsec SPI
A number from 256‐4294967295

outbound ESP cipher key
The outbound ESP key code, in hexadecimal

outbound ESP SPI
A number from 256‐4294967295
 outbound ESP authenticator key
The outbound ESP authenticator key code, in hexadecimal
Note:

When configuring a manual policy ESP, the ESP authenticator key is optional.

If using third‐party switches, the IPsec manual policy session key must be of fixed length as follows:

For AH key: SHA1 is 20 bytes; MD5 is 16 bytes

For ESP cipher key: 3DES is 24 bytes; AES‐cbc is 24 bytes; DES is 8 bytes

For ESP auth key: SHA1 is 20 bytes; MD5 is 16 bytes
3. After you configure the IPSec policy, you need to apply it to the interface to enforce the security policies on that interface and save it to keep it in place after a reboot. To accomplish this, enter: RS
RS
RS
RS
RS
© Copyright Lenovo 2016
G8052(config­ip)#interface ip <IP interface number, 1‐128>
G8052(config­ip­if)#address <IPv6 address>
G8052(config­ip­if)#ipsec manual­policy <policy index, 1‐10>
G8052(config­ip­if)#enable (enable the IP interface)
G8052#write (save the current configuration)
Chapter 25: IPsec with IPv6
391
Using a Dynamic Key Policy
When you use a dynamic key policy, the first packet triggers IKE and sets the IPsec SA and IKEv2 SA. The initial packet negotiation also determines the lifetime of the algorithm, or how long it stays in effect. When the key expires, a new key is automatically created. This helps prevent break‐ins.
To configure a dynamic key policy:
1. Choose a dynamic policy to configure. RS G8052(config)#ipsec dynamic­policy <policy number>
2. Configure the policy. RS
RS
RS
RS
RS
G8052(config­ipsec­dynamic)#peer <peer’s IPv6 address>
G8052(config­ipsec­dynamic)#traffic­selector <index of traffic selector>
G8052(config­ipsec­dynamic)#transform­set <index of transform set>
G8052(config­ipsec­dynamic)#sa­lifetime <SA lifetime, in seconds>
G8052(config­ipsec­dynamic)#pfs enable|disable
where the following parameters are used:

peer’s IPv6 address
The IPv6 address of the peer (for example, 3000::1)

index of traffic‐selector
A number from1‐10

index of transform‐set
A number from1‐10

SA lifetime, in seconds
The length of time the SA is to remain in effect; an integer from120‐86400 
pfs enable|disable
Whether to enable or disable the perfect forward security feature. The default is disable.
Note: In a dynamic policy, the AH and ESP keys are created by IKEv2.
3. After you configure the IPSec policy, you need to apply it to the interface to enforce the security policies on that interface and save it to keep it in place after a reboot. To accomplish this, enter: RS
RS
RS
RS
RS
392
G8052(config­ip)#interface ip <IP interface number, 1‐128>
G8052(config­ip­if)#address <IPv6 address>
G8052(config­ip­if)#ipsec dynamic­policy <policy index, 1‐10>
G8052(config­ip­if)#enable (enable the IP interface)
G8052#write (save the current configuration)
G8052 Application Guide for ENOS 8.4
Chapter 26. Routing Information Protocol
In a routed environment, routers communicate with one another to keep track of available routes. Routers can learn about available routes dynamically using the Routing Information Protocol (RIP). Lenovo Enterprise Network Operating System software supports RIP version 1 (RIPv1) and RIP version 2 (RIPv2) for exchanging TCP/IPv4 route information with other routers. Note: Enterprise NOS 8.4 does not support IPv6 for RIP.
© Copyright Lenovo 2016
393
Distance Vector Protocol
RIP is known as a distance vector protocol. The vector is the network number and next hop, and the distance is the metric associated with the network number. RIP identifies network reachability based on metric, and metric is defined as hop count. One hop is considered to be the distance from one switch to the next, which typically is 1. When a switch receives a routing update that contains a new or changed destination network entry, the switch adds 1 to the metric value indicated in the update and enters the network in the routing table. The IPv4 address of the sender is used as the next hop.
Stability
RIP includes a number of other stability features that are common to many routing protocols. For example, RIP implements the split horizon and hold‐down mechanisms to prevent incorrect routing information from being propagated. RIP prevents routing loops from continuing indefinitely by implementing a limit on the number of hops allowed in a path from the source to a destination. The maximum number of hops in a path is 15. The network destination network is considered unreachable if increasing the metric value by 1 causes the metric to be 16 (that is infinity). This limits the maximum diameter of a RIP network to less than 16 hops.
RIP is often used in stub networks and in small autonomous systems that do not have many redundant paths.
Routing Updates
RIP sends routing‐update messages at regular intervals and when the network topology changes. Each router “advertises” routing information by sending a routing information update every 30 seconds. If a router doesn’t receive an update from another router for 180 seconds, those routes provided by that router are declared invalid. The routes are removed from the routing table, but they remain in the RIP routes table. After another 120 seconds without receiving an update for those routes, the routes are removed from respective regular updates. When a router receives a routing update that includes changes to an entry, it updates its routing table to reflect the new route. The metric value for the path is increased by 1, and the sender is indicated as the next hop. RIP routers maintain only the best route (the route with the lowest metric value) to a destination. For more information, see the Configuration section, Routing Information Protocol Configuration in the Lenovo Enterprise Network Operating System Command Reference. 394
G8052 Application Guide for ENOS 8.4
RIPv1
RIP version 1 use broadcast User Datagram Protocol (UDP) data packets for the regular routing updates. The main disadvantage is that the routing updates do not carry subnet mask information. Hence, the router cannot determine whether the route is a subnet route or a host route. It is of limited usage after the introduction of RIPv2. For more information about RIPv1 and RIPv2, refer to RFC 1058 and RFC 2453. RIPv2
RIPv2 is the most popular and preferred configuration for most networks. RIPv2 expands the amount of useful information carried in RIP messages and provides a measure of security. For a detailed explanation of RIPv2, refer to RFC 1723 and RFC 2453. RIPv2 improves efficiency by using multicast UDP (address 224.0.0.9) data packets for regular routing updates. Subnet mask information is provided in the routing updates. A security option is added for authenticating routing updates, by using a shared password. ENOS supports using clear password for RIPv2. RIPv2 in RIPv1 Compatibility Mode
ENOS allows you to configure RIPv2 in RIPv1compatibility mode, for using both RIPv2 and RIPv1 routers within a network. In this mode, the regular routing updates use broadcast UDP data packet to allow RIPv1 routers to receive those packets. With RIPv1 routers as recipients, the routing updates have to carry natural or host mask. Hence, it is not a recommended configuration for most network topologies. Note: When using both RIPv1 and RIPv2 within a network, use a single subnet mask throughout the network. © Copyright Lenovo 2016
Chapter 26: Routing Information Protocol
395
RIP Features
ENOS provides the following features to support RIPv1 and RIPv2: 
Poison
Simple split horizon in RIP scheme omits routes learned from one neighbor in updates sent to that neighbor. That is the most common configuration used in RIP, that is setting this Poison to DISABLE. Split horizon with poisoned reverse includes such routes in updates, but sets their metrics to 16. The disadvantage of using this feature is the increase of size in the routing updates. 
Triggered Updates
Triggered updates are an attempt to speed up convergence. When Triggered Updates is enabled, whenever a router changes the metric for a route, it sends update messages almost immediately, without waiting for the regular update interval. It is recommended to enable Triggered Updates. 
Multicast
RIPv2 messages use IPv4 multicast address (224.0.0.9) for periodic broadcasts. Multicast RIPv2 announcements are not processed by RIPv1 routers. IGMP is not needed since these are inter‐router messages which are not forwarded. To configure RIPv2 in RIPv1 compatibility mode, set multicast to disable, and set version to both. 
Default
The RIP router can listen and supply a default route, usually represented as IPv4 0.0.0.0 in the routing table. When a router does not have an explicit route to a destination network in its routing table, it uses the default route to forward those packets.

Metric
The metric field contains a configurable value between 1 and 15 (inclusive) which specifies the current metric for the interface. The metric value typically indicates the total number of hops to the destination. The metric value of 16 represents an unreachable destination.

Authentication
RIPv2 authentication uses plaintext password for authentication. If configured using Authentication password, then it is necessary to enter an authentication key value. The following method is used to authenticate an RIP message: 
If the router is not configured to authenticate RIPv2 messages, then RIPv1 and unauthenticated RIPv2 messages are accepted; authenticated RIPv2 messages are discarded. 
If the router is configured to authenticate RIPv2 messages, then RIPv1 messages and RIPv2 messages which pass authentication testing are accepted; unauthenticated and failed authentication RIPv2 messages are discarded. For maximum security, RIPv1 messages are ignored when authentication is enabled; otherwise, the routing information from authenticated messages is propagated by RIPv1 routers in an unauthenticated manner.
396
G8052 Application Guide for ENOS 8.4
RIP Configuration Example
The following is an example of RIP configuration.
Note: An interface with RIP disabled uses all the default values of the RIP, no matter how the RIP parameters are configured for that interface. RIP sends out RIP regular updates to include an UP interface, but not a DOWN interface. 1. Add VLANs for routing interfaces. >> (config)# vlan 2
>> (config­vlan)# exit
>> (config)# interface port 2
>> (config­if)# switchport mode trunk
>> (config­if)# switchport trunk allowed vlan add 2
Port 2 is an UNTAGGED port and its current PVID is 1.
Confirm changing PVID from 1 to 2 [y/n]: y
>> (config­if)# exit
>> (config)# vlan 3
>> (config­vlan)# exit
>> (config)# interface port 3
>> (config­if)# switchport mode trunk
>> (config­if)# switchport trunk allowed vlan add 3
>> (config­if)# exit
Port 3 is an UNTAGGED port and its current PVID is 1.
Confirm changing PVID from 1 to 3 [y/n]: y
2. Add IP interfaces with IPv4 addresses to VLANs. >> # interface ip 2
>> (config­ip­if)# enable
>> (config­ip­if)# ip address 102.1.1.1
>> (config­ip­if)# vlan 2
>> (config­ip­if)# exit
>> # interface ip 3
>> (config­ip­if)# enable
>> (config­ip­if)# ip address 103.1.1.1
>> (config­ip­if)# vlan 3
3. Turn on RIP globally and enable RIP for each interface. >> # router rip
>> (config­router­rip)# enable
>> (config­router­rip)# exit
>> # interface ip 2
>> (config­ip­if)# ip rip enable
>> (config­ip­if)# exit
>> # interface ip 3
>> (config­ip­if)# ip rip enable
>> (config­ip­if)# exit
Use the following command to check the current valid routes in the routing table of the switch: >> # show ip route
© Copyright Lenovo 2016
Chapter 26: Routing Information Protocol
397
For those RIP routes learned within the garbage collection period, that are routes phasing out of the routing table with metric 16, use the following command: >> # show ip rip routes
Locally configured static routes do not appear in the RIP Routes table. 398
G8052 Application Guide for ENOS 8.4
Chapter 27. Internet Group Management Protocol
Internet Group Management Protocol (IGMP) is used by IPv4 Multicast routers (Mrouters) to learn about the existence of host group members on their directly attached subnet. The IPv4 Mrouters get this information by broadcasting IGMP Membership Queries and listening for IPv4 hosts reporting their host group memberships. This process is used to set up a client/server relationship between an IPv4 multicast source that provides the data streams and the clients that want to receive the data. The switch supports three versions of IGMP:

IGMPv1: Defines the method for hosts to join a multicast group. However, this version does not define the method for hosts to leave a multicast group. See RFC 1112 for details.

IGMPv2: Adds the ability for a host to signal its desire to leave a multicast group. See RFC 2236 for details.

IGMPv3: Adds support for source filtering by which a host can report interest in receiving packets only from specific source addresses, or from all but specific source addresses, sent to a particular multicast address. See RFC 3376 for details.
The G8052 can perform IGMP Snooping, and connect to static Mrouters. The G8052 can act as a Querier, and participate in the IGMP Querier election process.
The following topics are discussed in this chapter:
© Copyright Lenovo 2016

“IGMP Terms” on page 400

“How IGMP Works” on page 401

“IGMP Capacity and Default Values” on page 402

“IGMP Snooping” on page 404

“IGMP Relay” on page 417

“Additional IGMP Features” on page 426
399
IGMP Terms
The following are commonly used IGMP terms:
400

Multicast traffic: Flow of data from one source to multiple destinations.

Group: A multicast stream to which a host can join. Multicast groups have IP addresses in the range: 224.0.1.0 to 239.255.255.255.

IGMP Querier: A router or switch in the subnet that generates Membership Queries.

IGMP Snooper: A Layer 3 device that forwards multicast traffic only to hosts that are interested in receiving multicast data. This device can be a router or a Layer 3 switch.

Multicast Router: A router configured to make routing decisions for multicast traffic. The router identifies the type of packet received (unicast or multicast) and forwards the packet to the intended destination.

IGMP Proxy: A device that filters Join messages and Leave messages sent upstream to the Mrouter to reduce the load on the Mrouter.

Membership Report: A report sent by the host that indicates an interest in receiving multicast traffic from a multicast group.

Leave: A message sent by the host when it wants to leave a multicast group.

FastLeave: A process by which the switch stops forwarding multicast traffic to a port as soon as it receives a Leave message.

Membership Query: Message sent by the Querier to verify if hosts are listening to a group.

General Query: A Membership Query sent to all hosts. The Group address field for general queries is 0.0.0.0 and the destination address is 224.0.0.1.

Group‐specific Query: A Membership Query sent to all hosts in a multicast group.
G8052 Application Guide for ENOS 8.4
How IGMP Works
When IGMP is not configured, switches forward multicast traffic through all ports, increasing network load. When IGMPv2 is configured on a switch, multicast traffic flows as follows:

A server sends multicast traffic to a multicast group.

The Mrouter sends Membership Queries to the switch, which forwards them to all ports in a given VLAN.

Hosts respond with Membership Reports if they want to join a group. The switch forwards these reports to the Mrouter.
Any new IGMP report which causes the IGMP entries limit to be exceeded will still be sent to the multicast router(s).

The switch forwards multicast traffic only to hosts that have joined a group.

The Mrouter periodically sends Membership Queries to ensure that a host wants to continue receiving multicast traffic. If a host does not respond, the IGMP Snooper stops sending traffic to the host.

The host can initiate the Leave process by sending an IGMP Leave packet to the IGMP Snooper.

When a host sends an IGMPv2 Leave packet, the IGMP Snooper queries to find out if any other host connected to the port is interested in receiving the multicast traffic. If it does not receive a Join message in response, the IGMP Snooper removes the group entry and passes on the information to the Mrouter.
The G8052 supports the following: IGMP version 1, 2, and 3
 128 static Mrouters and 128 dynamic Mrouters

Note: Unknown multicast traffic is sent to all ports if the flood option is enabled and no Membership Report was learned for that specific IGMP group. If the flood option is disabled, unknown multicast traffic is discarded if no hosts or Mrouters are learned on a switch.
To enable or disable IGMP flood, use the following command:
RS G8052(config)# vlan <vlan ID>
RS G8052(config-vlan)# [no] flood
© Copyright Lenovo 2016
Chapter 27: Internet Group Management Protocol
401
IGMP Capacity and Default Values
The following table lists the maximum and minimum values of the G8052 variables.
Note: When having maximum number of IGMP entries installed, any received GMP Reports/Leaves are sent to mrouter (if it exists). Table 30. G8052 Capacity Table
Variable
Maximum
IGMP Entries ‐ Snoop
4096
IGMP Entries ‐ Relay
1000
VLANs ‐ Snoop
1024
VLANs ‐ Relay
8
Static Mrouters
128
Dynamic Mrouters
128
Number of IGMP Filters
16
IPMC Groups (IGMP Relay)
1000
The following table lists the default settings for IGMP features and variables. Table 31. IGMP Default Configuration Settings
402
Field
Default Value
Global IGMP State
Disabled
IGMP Querier
Disabled
IGMP Snooping
Disabled
IGMP Filtering
Disabled
IP Multicast (IPMC) Flood
Enabled
IGMP FastLeave
Disabled for all VLANs
IGMP Mrouter Timeout
255 Seconds
IGMP Report Timeout Variable
10 Seconds
IGMP Query‐Interval Variable
125 Seconds
IGMP Robustness Variable
2
IGMPv3
Disabled
G8052 Application Guide for ENOS 8.4
Table 31. IGMP Default Configuration Settings (continued)
Field
Default Value
IGMPv3 number of sources
8 (The switch processes only the first eight sources listed in the IGMPv3 group record.)
Valid range: 1 ‐ 64
IGMPv3 ‐ allow v1v2 Snooping
© Copyright Lenovo 2016
Enabled
Chapter 27: Internet Group Management Protocol
403
IGMP Snooping
IGMP Snooping allows a switch to listen to the IGMP conversation between hosts and Mrouters. By default, a switch floods multicast traffic to all ports in a broadcast domain. With IGMP Snooping enabled, the switch learns the ports interested in receiving multicast data and forwards it only to those ports. IGMP Snooping conserves network resources.
The switch can sense IGMP Membership Reports from attached hosts and acts as a proxy to set up a dedicated path between the requesting host and a local IPv4 Mrouter. After the path is established, the switch blocks the IPv4 multicast stream from flowing through any port that does not connect to a host member, thus conserving bandwidth.
IGMP Querier
For IGMP Snooping to function, you must have an Mrouter on the network that generates IGMP Query packets. Enabling the IGMP Querier feature on the switch allows it to participate in the Querier election process. If the switch is elected as the Querier, it will send IGMP Query packets for the LAN segment.
Querier Election
If multiple Mrouters exist on the network, only one can be elected as a Querier. The Mrouters elect the one with the lowest source IPv4 address or MAC address as the Querier. The Querier performs all periodic membership queries. All other Mrouters (non‐Queriers) do not send IGMP Query packets.
Note: When IGMP Querier is enabled on a VLAN, the switch performs the role of an IGMP Querier only if it meets the IGMP Querier election criteria.
Each time the Querier switch sends an IGMP Query packet, it initializes a general query timer. If a Querier receives a General Query packet from an Mrouter with a lower IP address or MAC address, it transitions to a non‐Querier state and initializes an other querier present timer. When this timer expires, the Mrouter transitions back to the Querier state and sends a General Query packet.
Follow this procedure to configure IGMP Querier.
1. Enable IGMP and configure the source IPv4 address for IGMP Querier on a VLAN. RS G8052(config)# ip igmp enable
RS G8052(config)# ip igmp querier vlan 2 source­ip 10.10.10.1
2. Enable IGMP Querier on the VLAN. RS G8052(config)# ip igmp querier vlan 2 enable
3. Configure the querier election type and define the address. RS G8052(config)# ip igmp querier vlan 2 election­type ipv4
404
G8052 Application Guide for ENOS 8.4
4. Verify the configuration. RS G8052# show ip igmp querier vlan 2
Current IGMP snooping Querier information:
IGMP Querier information for vlan 2:
Other IGMP querier ­ none
Switch­querier enabled, current state: Querier
Switch­querier type: Ipv4, address 10.10.10.1,
Switch­querier general query interval: 125 secs,
Switch­querier max­response interval: 100 'tenths of secs',
Switch­querier startup interval: 31 secs, count: 2
Switch­querier robustness: 2
IGMP configured version is v3
IGMP Operating version is v3
IGMP Groups
One IGMP entry is allocated for each unique join request, based on the VLAN and IGMP group address. If multiple ports join the same IGMP group using the same VLAN, only a single IGMP entry is used.
IGMPv3 Snooping
IGMPv3 includes new Membership Report messages that extend IGMP functionality. The switch provides snooping capability for all types of IGMPv3 Membership Reports.
IGMPv3 is supported in stand‐alone (non‐stacking) mode only.
IGMPv3 supports Source‐Specific Multicast (SSM). SSM identifies session traffic by both source and group addresses. The IGMPv3 implementation keeps records on the multicast hosts present in the network. If a host is already registered, when it receives a new IS_INC, TO_INC, IS_EXC, or TO_EXC report from same host, the switch makes the correct transition to new (port‐host‐group) registration based on the IGMPv3 RFC. The registrations of other hosts for the same group on the same port are not changed.
The IGMPv3 implementation keeps records on the multicast hosts present in the network. If a host is already registered, when it sends an IS_INC/TO_INC/IS_EXC/TO_EXC report, the switch overwrites the existing (port‐host‐group) registration with the new registration; the registrations of other hosts on the same group, same port are not changed. IS_INCLUDE/TO_INCLUDE reports with no source are not registered.
The G8052 supports the following IGMPv3 filter modes:
INCLUDE mode: The host requests membership to a multicast group and pro‐
vides a list of IPv4 addresses from which it wants to receive traffic.
 EXCLUDE mode: The host requests membership to a multicast group and provides a list of IPv4 addresses from which it does not want to receive traffic. This indicates that the host wants to receive traffic only from sources that are not part of the Exclude list. To disable snooping on EXCLUDE mode reports, use the following command: 
RS G8052(config)# no ip igmp snoop igmpv3 exclude
© Copyright Lenovo 2016
Chapter 27: Internet Group Management Protocol
405
By default, the G8052 snoops the first eight sources listed in the IGMPv3 Group Record. Use the following command to change the number of snooping sources: RS G8052(config)# ip igmp snoop igmpv3 sources <1‐64>
IGMPv3 Snooping is compatible with IGMPv1 and IGMPv2 Snooping. To disable snooping on version 1 and version 2 reports, use the following command: RS G8052(config)# no ip igmp snoop igmpv3 v1v2 406
G8052 Application Guide for ENOS 8.4
IGMP Snooping Configuration Guidelines
Consider the following guidelines when you configure IGMP Snooping:
© Copyright Lenovo 2016

IGMP operation is independent of the routing method. You can use RIP, OSPF, or static routes for Layer 3 routing.

When multicast traffic flood is disabled, the multicast traffic sent by the multicast server is discarded if no hosts or Mrouters are learned on the switch.

The Mrouter periodically sends IGMP Queries.

The switch learns the Mrouter on the port connected to the router when it sees Query messages. The switch then floods the IGMP queries on all other ports including a LAG, if any.

Multicast hosts send IGMP Reports as a reply to the IGMP Queries sent by the Mrouter.

The switch can also learn an Mrouter when it receives a PIM hello packet from another device. However, an Mrouter learned from a PIM packet has a lower priority than an Mrouter learned from an IGMP Query. A switch overwrites an Mrouter learned from a PIM packet when it receives an IGMP Query on the same port.

A host sends an IGMP Leave message to its multicast group. The expiration timer for this group is updated to 10 seconds. The Layer 3 switch sends IGMP Group‐Specific Query to the host that had sent the Leave message. If the host does not respond with an IGMP Report during these 10 seconds, all the groups expire and the switch deletes the host from the IGMP groups table. The switch then proxies the IGMP Leave messages to the Mrouter.
Chapter 27: Internet Group Management Protocol
407
IGMP Snooping Configuration Example
This section provides steps to configure IGMP Snooping on the G8052.
1. Configure port and VLAN membership on the switch.
2. Add VLANs to IGMP Snooping. RS G8052(config)# ip igmp snoop vlan 1 3. Enable IGMP Snooping. RS G8052(config)# ip igmp snoop enable
4. Enable IGMPv3 Snooping (optional). RS G8052(config)# ip igmp snoop igmpv3 enable
5. Enable the IGMP feature. RS G8052(config)# ip igmp enable
6. View dynamic IGMP information. RS G8052# show ip igmp groups
Total entries: 5 Total IGMP groups: 2
Note: The <Total IGMP groups> number is computed as
the number of unique (Group, Vlan) entries!
Note: Local groups (224.0.0.x) are not snooped/relayed and will not appear.
Source Group VLAN Port Version Mode Expires Fwd
­­­­­­­­­­ ­­­­­­­­­­­­­­­ ­­­­­­­ ­­­­­­ ­­­­­­­­ ­­­­­ ­­­­­­­ ­­­
10.1.1.1 232.1.1.1 2 4 V3 INC 4:16 Yes
10.1.1.5 232.1.1.1 2 4 V3 INC 4:16 Yes
* 232.1.1.1 2 4 V3 INC ­ No
10.10.10.43 235.0.0.1 9 1 V3 EXC 2:26 No
* 235.0.0.1 9 1 V3 EXC ­ Yes
RS G8052# show ip igmp mrouter
Total entries: 3 Total number of dynamic mrouters: 2
Total number of installed static mrouters: 1
SrcIP VLAN Port Version Expires MRT QRV QQIC ­­­­­­­ ­­­­­­­ ­­­­­­­ ­­­­­­­­­ ­­­­­­­­ ­­­­­­­ ­­­­ ­­­­ 10.1.1.1 2 21 V3 4:09 128 2 125
10.1.1.5 2 23 V2 4:09 125 ­ ­
* 9 24 V2 static ­ ­ ­
These commands display information about IGMP Groups and Mrouters learned by the switch. 408
G8052 Application Guide for ENOS 8.4
Advanced Configuration Example: IGMP Snooping
Figure 30 shows an example topology. Switches B and C are configured with IGMP Snooping.
Figure 30. Topology
Multicast
Host 1
Multicast
Host 2
VLAN 2
VLANs 2,3
Switch B
5
6
1
Multicast
Host 3
2
Multicast
Router
VLAN 3
Switch C
LAG 3
VLANs 2, 3
3
4
VLANs 2,3
3
4
5
6
1
2
Switch A
LAG 1
LAG 2
VLANs 2, 3
VLANs 2, 3
2
1
5
4
3
VLANs 2,3
Multicast
Server
Devices in this topology are configured as follows:
© Copyright Lenovo 2016

STG2 includes VLAN2; STG3 includes VLAN3.

The multicast server sends IP multicast traffic for the following groups:

VLAN 2, 225.10.0.11 – 225.10.0.12, Source: 22.10.0.11

VLAN 2, 225.10.0.13 – 225.10.0.15, Source: 22.10.0.13

VLAN 3, 230.0.2.1 – 230.0.2.2, Source: 22.10.0.1

VLAN 3, 230.0.2.3 – 230.0.2.5, Source: 22.10.0.3

The Mrouter sends IGMP Query packets in VLAN 2 and VLAN 3. The Mrouter’s IP address is 10.10.10.10.

The multicast hosts send the following IGMP Reports:

IGMPv2 Report, VLAN 2, Group: 225.10.0.11, Source: *

IGMPv2 Report, VLAN 3, Group: 230.0.2.1, Source: *

IGMPv3 IS_INCLUDE Report, VLAN 2, Group: 225.10.0.13, Source: 22.10.0.13

IGMPv3 IS_INCLUDE Report, VLAN 3, Group: 230.0.2.3, Source: 22.10.0.3
Chapter 27: Internet Group Management Protocol
409
The hosts receive multicast traffic as follows:


Host 1 receives multicast traffic for groups (*, 225.10.0.11), (22.10.0.13, 225.10.0.13)

Host 2 receives multicast traffic for groups (*, 225.10.0.11), (*, 230.0.2.1), (22.10.0.13, 225.10.0.13), (22.10.0.3, 230.0.2.3)

Host 3 receives multicast traffic for groups (*, 230.0.2.1), (22.10.0.3, 230.0.2.3)
The Mrouter receives all the multicast traffic.

Prerequisites
Before you configure IGMP Snooping, ensure you have performed the following actions:

Configured VLANs.

Enabled IGMP.

Added VLANs to IGMP Snooping. 
Configured a switch or Mrouter as the Querier.

Identified the IGMP version(s) you want to enable.

Disabled IGMP flooding.
Configuration
This section provides the configuration details of the switches shown in Figure 30.
Switch A Configuration
1. Configure VLANs and tagging.
RS
RS
RS
RS
G8052(config)# interface port 1­5
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 2,3
G8052(config­if)# exit
2. Configure an IP interface with IPv4 address, and assign a VLAN.
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip address 10.10.10.1 enable
G8052(config­ip­if)# vlan 2
G8052(config­ip­if)# exit
3. Assign a bridge priority lower than the default bridge priority to enable the switch to become the STP root in STG 2 and 3.
RS G8052(config)# spanning­tree stp 2 bridge priority 4096
RS G8052(config)# spanning­tree stp 3 bridge priority 4096
410
G8052 Application Guide for ENOS 8.4
4. Configure LACP dynamic LAGs (portchannels).
RS
RS
RS
RS
G8052(config)# interface port 1
G8052(config­if)# lacp key 100
G8052(config­if)# lacp mode active
G8052(config­if)# exit
RS
RS
RS
RS
G8052(config)# interface port 2
G8052(config­if)# lacp key 100
G8052(config­if)# lacp mode active
G8052(config­if)# exit
RS
RS
RS
RS
G8052(config)# interface port 3
G8052(config­if)# lacp key 200
G8052(config­if)# lacp mode active
G8052(config­if)# exit
RS G8052(config)# interface port 4
RS G8052(config­if)# lacp key 200
RS G8052(config­if)# lacp mode active
Switch B Configuration
1. Configure VLANs and tagging.
RS
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 2,3
G8052(config­vlan)# interface port 1­4,6
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 2,3
G8052(config­if)# exit
G8052(config)# interface port 5
G8052(config­if)# switchport access vlan 2
2. Configure an IP interface with IPv4 address, and assign a VLAN.
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip address 10.10.10.2 enable
G8052(config­ip­if)# vlan 2
G8052(config­ip­if)# exit
3. Configure STP. Reset the ports to make the edge configuration operational.
RS
RS
RS
RS
RS
G8052(config)# interface port 5,6
G8052(config­if)# spanning­tree portfast
G8052(config­if)# shutdown
G8052(config­if)# no shutdown
G8052(config­if)# exit
4. Configure an LACP dynamic LAG (portchannel).
RS
RS
RS
RS
G8052(config)# interface port 1,2
G8052(config­if)# lacp key 300
G8052(config­if)# lacp mode active
G8052(config­if)# exit
5. Configure a static LAG (portchannel).
RS G8052(config)# portchannel 1 port 3,4 enable
© Copyright Lenovo 2016
Chapter 27: Internet Group Management Protocol
411
6. Configure IGMP Snooping.
RS
RS
RS
RS
RS
RS
G8052(config)# ip igmp enable
G8052(config)# ip igmp snoop vlan 2,3
G8052(config)# ip igmp snoop source­ip 10.10.10.2
G8052(config)# ip igmp snoop igmpv3 enable
G8052(config)# ip igmp snoop igmpv3 sources 64
G8052(config)# ip igmp snoop enable
RS G8052(config)# vlan 2
RS G8052(config­vlan)# no flood
RS G8052(config­vlan)# exit
RS G8052(config)# vlan 3
RS G8052(config­vlan)# no flood
RS G8052(config­vlan)# exit
Switch C Configuration
1. Configure VLANs and tagging.
RS
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 2,3
G8052(config­vlan)# interface port 1­4,6
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 2,3
G8052(config­if)# exit
G8052(config)# interface port 5
G8052(config­if)# switchport access vlan 3
2. Configure an IP interface with IPv4 address, and assign a VLAN.
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip address 10.10.10.3 enable
G8052(config­ip­if)# vlan 2
G8052(config­ip­if)# exit
3. Configure STP. Reset the ports to make the edge configuration operational.
RS
RS
RS
RS
RS
G8052(config)# interface port 5,6
G8052(config­if)# spanning­tree portfast
G8052(config­if)# shutdown
G8052(config­if)# no shutdown
G8052(config­if)# exit
4. Configure an LACP dynamic LAG (portchannel).
RS
RS
RS
RS
G8052(config)# interface port 1,2
G8052(config­if)# lacp key 400
G8052(config­if)# lacp mode active
G8052(config­if)# exit
5. Configure a static LAG (portchannel).
RS G8052(config)# portchannel 1 port 3,4 enable
412
G8052 Application Guide for ENOS 8.4
6. Configure IGMP Snooping.
RS
RS
RS
RS
RS
RS
G8052(config)# ip igmp enable
G8052(config)# ip igmp snoop vlan 2,3
G8052(config)# ip igmp snoop source­ip 10.10.10.3
G8052(config)# ip igmp snoop igmpv3 enable
G8052(config)# ip igmp snoop igmpv3 sources 64
G8052(config)# ip igmp snoop enable
RS G8052(config)# vlan 2
RS G8052(config­vlan)# no flood
RS G8052(config­vlan)# exit
RS G8052(config)# vlan 3
RS G8052(config­vlan)# no flood
RS G8052(config­vlan)# exit
© Copyright Lenovo 2016
Chapter 27: Internet Group Management Protocol
413
Troubleshooting IGMP Snooping
This section provides the steps to resolve common IGMP Snooping configuration issues. The topology described in Figure 30 is used as an example.

Multicast traffic from non‐member groups reaches the host or Mrouter

Check if traffic is unregistered. For unregistered traffic, an IGMP entry is not displayed in the IGMP groups table.
RS G8052# show ip igmp groups

Ensure IPMC flooding is disabled and CPU is enabled.
RS G8052(config)# vlan <vlan id>
RS G8052(config­vlan)# no flood
RS G8052(config­vlan)# cpu

Check the egress port’s VLAN membership. The ports to which the hosts and Mrouter are connected must be used only for VLAN 2 and VLAN 3.
RS G8052# show vlan
Note: To avoid such a scenario, disable IPMC flooding for all VLANs enabled on the switches (if this is an acceptable configuration).

Check IGMP Reports on switches B and C for information about the IGMP groups.
RS G8052# show ip igmp groups
If the non‐member IGMP groups are displayed in the table, close the application that may be sending the IGMP Reports for these groups. Identify the traffic source by using a sniffer on the hosts and reading the source IP/MAC address. If the source IP/MAC address is unknown, check the port statistics to find the ingress port.
RS G8052# show interface port <port id> interface­counters
414

Ensure no static multicast MACs, static multicast groups, or static Mrouters are configured.

Ensure IGMP Relay and PIM are not configured.
G8052 Application Guide for ENOS 8.4

Not all multicast traffic reaches the appropriate receivers.

Ensure hosts are sending IGMP Reports for all the groups. Check the VLAN on which the groups are learned.
RS G8052# show ip igmp groups
If some of the groups are not displayed, ensure the multicast application is running on the host device and the generated IGMP Reports are correct.

Ensure multicast traffic reaches the switch to which the host is connected.
Close the application sending the IGMP Reports. Clear the IGMP groups by disabling, then re‐enabling the port.
Note: To clear all IGMP groups, use the following command:
RS G8052(config)# clear ip igmp groups
However, this will clear all the IGMP groups and will influence other hosts.
Check if the multicast traffic reaches the switch.
RS G8052# show ip igmp ipmcgrp
If the multicast traffic group is not displayed in the table, check the link state, VLAN membership, and STP convergence.


Ensure multicast server is sending all the multicast traffic.

Ensure no static multicast MACs, static multicast groups, or static multicast routes are configured.
IGMP queries sent by the Mrouter do not reach the host.

Ensure the Mrouter is learned on switches B and C.
RS G8052# show ip igmp mrouter
If it is not learned on switch B but is learned on switch C, check the link state of the LAG, VLAN membership, and STP convergence.
If it is not learned on any switch, ensure the multicast application is running and is sending correct IGMP Query packets.
If it is learned on both switches, check the link state, VLAN membership, and STP port states for the ports connected to the hosts.
© Copyright Lenovo 2016
Chapter 27: Internet Group Management Protocol
415

IGMP Reports/Leaves sent by the hosts do not reach the Mrouter

Ensure IGMP Queries sent by the Mrouter reach the hosts.

Ensure the Mrouter is learned on both switches. Note that the Mrouter may not be learned on switch B immediately after a LAG failover/failback.
RS G8052# show ip igmp mrouter

Ensure the host’s multicast application is started and is sending correct IGMP Reports/Leaves.
RS G8052# show ip igmp groups
RS G8052# show ip igmp counters



A host receives multicast traffic from the incorrect VLAN

Check port VLAN membership.

Check IGMP Reports sent by the host.

Check multicast data sent by the server.
The Mrouter is learned on the incorrect LAG

Check link state. LAG 1 might be down or in STP discarding state.

Check STP convergence.

Check port VLAN membership.
Hosts receive multicast traffic at a lower rate than normal
Note: This behavior is expected if IPMC flood is disabled and CPU is enabled. As soon as the IGMP/IPMC entries are installed on ASIC, the IPMC traffic recovers and is forwarded at line rate. This applies to unregistered IPMC traffic. 
Ensure a storm control is not configured on the LAGs.
RS G8052(config)# interface port <port id>
RS G8052(config­if)# no storm­control multicast

416
Check link speeds and network congestion.
G8052 Application Guide for ENOS 8.4
IGMP Relay
The G8052 can act as an IGMP Relay (or IGMP Proxy) device that relays IGMP multicast messages and traffic between an Mrouter and end stations. IGMP Relay allows the G8052 to participate in network multicasts with no configuration of the various multicast routing protocols, so you can deploy it in the network with minimal effort.
To an IGMP host connected to the G8052, IGMP Relay appears to be an IGMP Mrouter. IGMP Relay sends Membership Queries to hosts, which respond by sending an IGMP response message. A host can also send an unsolicited Join message to the IGMP Relay.
To an Mrouter, IGMP Relay appears as a host. The Mrouter sends IGMP host queries to IGMP Relay, and IGMP Relay responds by forwarding IGMP host reports and unsolicited Join messages from its attached hosts.
IGMP Relay also forwards multicast traffic between the Mrouter and end stations, similar to IGMP Snooping.
You can configure up to two Mrouters to use with IGMP Relay. One Mrouter acts as the primary Mrouter, and one is the backup Mrouter. The G8052 uses health checks to select the primary Mrouter.
Configuration Guidelines
Consider the following guidelines when you configure IGMP Relay:
IGMP Relay and IGMP Snooping are mutually exclusive—if you enable IGMP Relay, you must turn off IGMP Snooping/Querier.
 Add the upstream Mrouter VLAN to the IGMP Relay list, using the following command:

RS G8052(config)# ip igmp relay vlan <VLAN number>

If IGMP hosts reside on different VLANs, you must: 
Disable IGMP flooding. RS G8052(config)# vlan <vlan id>
RS G8052(config­vlan)# no flood

Ensure CPU forwarding is enabled; Ensure that multicast data is forwarded across the VLANs. RS G8052(config)# vlan <vlan id>
RS G8052(config­vlan)# cpu
© Copyright Lenovo 2016
Chapter 27: Internet Group Management Protocol
417
Configure IGMP Relay
Use the following procedure to configure IGMP Relay.
1. Configure IP interfaces with IPv4 addresses, and assign VLANs.
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface ip 2
G8052(config­ip­if)# ip address 10.10.1.1
G8052(config­ip­if)# ip netmask 255.255.255.0
G8052(config­ip­if)# vlan 2
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
G8052(config)# interface ip 3
G8052(config­ip­if)# ip address 10.10.2.1
G8052(config­ip­if)# ip netmask 255.255.255.0
G8052(config­ip­if)# vlan 3
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
2. Turn IGMP on.
RS G8052(config)# ip igmp enable
3. Configure the upstream Mrouters with IPv4 addresses.
RS
RS
RS
RS
G8052(config)# ip igmp relay mrouter 1 address 100.0.1.2
G8052(config)# ip igmp relay mrouter 1 enable
G8052(config)# ip igmp relay mrouter 2 address 100.0.2.4
G8052(config)# ip igmp relay mrouter 2 enable
4. Enable IGMP Relay and add VLANs to the downstream network.
RS G8052(config)# ip igmp relay vlan 2
RS G8052(config)# ip igmp relay vlan 3
RS G8052(config)# ip igmp relay enable
418
G8052 Application Guide for ENOS 8.4
Advanced Configuration Example: IGMP Relay
Figure 31 shows an example topology. Switches B and C are configured with IGMP Relay.
Figure 31. Topology
Multicast
Host 1
VLAN 3
VLANs 2,3
Switch B
5
1
2
VLAN 5
VLAN 2
VLAN 2
3
4
Multicast
Router 2
Switch C
LAG 3
6
Multicast
Router 1
Multicast
Host 3
Multicast
Host 2
3
4
5
6
7 VLAN 5
1
2
Switch A
LAG 1
LAG 2
VLAN 2
VLAN 2
2
1
5
4
3
VLAN 2
Multicast
Server
Devices in this topology are configured as follows:

The IP address of Multicast Router 1 is 5.5.5.5

The IP address of Multicast Router 2 is 5.5.5.6

STG 2 includes VLAN2; STG 3 includes VLAN 3; STG 5 includes VLAN 5.

The multicast server sends IP multicast traffic for the following groups:



VLAN 2, 225.10.0.11 – 225.10.0.15
The multicast hosts send the following IGMP Reports:

Host 1: 225.10.0.11 – 225.10.0.12, VLAN 3

Host 2: 225.10.0.12 – 225.10.0.13, VLAN 2; 225.10.0.14 – 225.10.0.15, VLAN 3

Host 3: 225.10.0.13 – 225.10.0.14, VLAN 2
The Mrouter receives all the multicast traffic.
Prerequisites
Before you configure IGMP Relay, ensure you have performed the following actions:
© Copyright Lenovo 2016

Configured VLANs.

Enabled IGMP.
Chapter 27: Internet Group Management Protocol
419

Disabled IGMP flooding.

Disabled IGMP Snooping.
Configuration
This section provides the configuration details of the switches in Figure 31.
Switch A Configuration
1. Configure a VLAN.
RS G8052(config)# interface port 1­5
RS G8052(config­if)# switchport access vlan 2
2. Configure an IP interface with IPv4 address, and assign a VLAN..
RS
RS
RS
RS
G8052(config)# interface ip 2
G8052(config­ip­if)# ip address 2.2.2.10 enable
G8052(config­ip­if)# vlan 2
G8052(config­ip­if)# exit
3. Assign a bridge priority lower than the default bridge priority to enable the switch to become the STP root in STG 2 and 3.
RS G8052(config)# spanning­tree stp 2 bridge priority 4096
4. Configure LACP dynamic LAGs (portchannels).
RS
RS
RS
RS
G8052(config)# interface port 1,2
G8052(config­if)# lacp key 100
G8052(config­if)# lacp mode active
G8052(config­if)# exit
RS G8052(config)# interface port 3,4
RS G8052(config­if)# lacp key 200
RS G8052(config­if)# lacp mode active
420
G8052 Application Guide for ENOS 8.4
Switch B Configuration
1. Configure VLANs and tagging.
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 2,3
G8052(config­vlan)# interface port 1­4
G8052(config­if)# switchport access vlan 2
G8052(config­if)# exit
G8052(config)# interface port 5
G8052(config­if)# switchport access vlan 3
G8052(config­if)# exit
G8052(config)# interface port 6
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 2,3
G8052(config­if)# exit
2. Configure IP interfaces with IPv4 addresses, and assign VLANs.
RS
RS
RS
RS
G8052(config)# interface ip 2
G8052(config­ip­if)# ip address 2.2.2.20 enable
G8052(config­ip­if)# vlan 2
G8052(config­ip­if)# exit
RS
RS
RS
RS
G8052(config)# interface ip 3
G8052(config­ip­if)# ip address 3.3.3.20 enable
G8052(config­ip­if)# vlan 3
G8052(config­ip­if)# exit
RS G8052(config)# ip gateway 2 address 2.2.2.30 enable
3. Configure STP.
RS
RS
RS
RS
RS
G8052(config)# interface port 5,6
G8052(config­if)# spanning­tree portfast
G8052(config­if)# shutdown
G8052(config­if)# no shutdown
G8052(config­if)# exit
4. Configure an LACP dynamic LAG (portchannel). RS
RS
RS
RS
G8052(config)# interface port 1,2
G8052(config­if)# lacp key 300
G8052(config­if)# lacp mode active
G8052(config­if)# exit
5. Configure a static LAG (portchannel).
RS G8052(config)# portchannel 1 port 3,4 enable
© Copyright Lenovo 2016
Chapter 27: Internet Group Management Protocol
421
6. Configure IGMP Relay.
RS
RS
RS
RS
RS
G8052(config)# ip igmp enable
G8052(config)# ip igmp relay vlan 2,3
G8052(config)# ip igmp relay mrouter 1 address 5.5.5.5 enable
G8052(config)# ip igmp relay mrouter 2 address 5.5.5.6 enable
G8052(config)# ip igmp relay enable
RS G8052(config)# vlan 2
RS G8052(config­vlan)# no flood
RS G8052(config­vlan)# exit
RS G8052(config)# vlan 3
RS G8052(config­vlan)# no flood
RS G8052(config­vlan)# exit
Switch C Configuration
1. Configure VLANs.
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 2,3,5
G8052(config­vlan)# interface port 1­5
G8052(config­if)# switchport access vlan 2
G8052(config­if)# interface port 6,7
G8052(config­if)# switchport access vlan 5
G8052(config­if)# exit
2. Configure IP interfaces with IPv4 addresses and assign VLANs.
RS
RS
RS
RS
G8052(config)# interface ip 2
G8052(config­ip­if)# ip address 2.2.2.30 enable
G8052(config­ip­if)# vlan 2
G8052(config­ip­if)# exit
RS
RS
RS
RS
G8052(config)# interface ip 3
G8052(config­ip­if)# ip address 5.5.5.30 enable
G8052(config­ip­if)# vlan 5
G8052(config­ip­if)# exit
RS G8052(config)# ip gateway 2 address 2.2.2.20 enable
3. Configure STP.
RS
RS
RS
RS
RS
G8052(config)# interface port 5,6,7
G8052(config­if)# spanning­tree portfast
G8052(config­if)# shutdown
G8052(config­if)# no shutdown
G8052(config­if)# exit
4. Configure LACP dynamic LAG (portchannel).
RS
RS
RS
RS
422
G8052(config)# interface port 1,2
G8052(config­if)# lacp key 400
G8052(config­if)# lacp mode active
G8052(config­if)# exit
G8052 Application Guide for ENOS 8.4
5. Configure a static LAG (portchannel).
RS G8052(config)# portchannel 1 port 3,4 enable
6. Enable IGMP.
RS G8052(config)# ip igmp enable
7. Configure IGMP Relay.
RS
RS
RS
RS
G8052(config)# ip igmp relay vlan 2,5
G8052(config)# ip igmp relay mrouter 1 address 5.5.5.5 enable
G8052(config)# ip igmp relay mrouter 2 address 5.5.5.6 enable
G8052(config)# ip igmp relay enable
RS G8052(config)# vlan 2
RS G8052(config­vlan)# no flood
RS G8052(config­vlan)# exit
RS G8052(config)# vlan 5
RS G8052(config­vlan)# no flood
RS G8052(config­vlan)# exit
Troubleshooting IGMP Relay
This section provides the steps to resolve common IGMP Relay configuration issues. The topology described in Figure 31 is used as an example.

Multicast traffic from non‐member groups reaches the hosts or the Mrouter

Ensure IPMC flood is disabled.
RS G8052(config)# vlan <vlan id>
RS G8052(config­vlan)# no flood

Check the egress port’s VLAN membership. The ports to which the hosts and Mrouter are connected must be used only for VLAN 2, VLAN 3, or VLAN 5.
RS G8052(config)# show vlan
© Copyright Lenovo 2016
Chapter 27: Internet Group Management Protocol
423
Note: To avoid such a scenario, disable IPMC flooding for all VLANs enabled on the switches (if this is an acceptable configuration).

Check IGMP Reports on switches B and C for information about IGMP groups.
RS G8052(config)# show ip igmp groups
If non‐member IGMP groups are displayed in the table, close the application that may be sending the IGMP Reports for these groups. Identify the traffic source by using a sniffer on the hosts and reading the source IP address/MAC address. If the source IP address/MAC address is unknown, check the port statistics to find the ingress port.
RS G8052(config)# show interface port <port id> interface­counters


Ensure no static multicast MACs and static Mrouters are configured.
Not all multicast traffic reaches the appropriate receivers
Ensure hosts are sending IGMP Reports for all the groups. Check the VLAN on which the groups are learned.
RS G8052(config)# show ip igmp groups
If some of the groups are not displayed, ensure the multicast application is running on the host device and the generated IGMP Reports are correct.

Ensure the multicast traffic reaches the switch to which the host is connected.
Close the application sending the IGMP Reports. Clear the IGMP groups by flapping (disabling, then re‐enabling) the port.
Note: To clear all IGMP groups, you can use the following command
RS G8052(config)# clear ip igmp groups
However, this will clear all the IGMP groups and will influence other hosts.
Check if the multicast traffic reaches the switch.
RS G8052(config)# show ip igmp ipmcgrp
If the multicast traffic group is not displayed in the table, check the link state, VLAN membership, and STP convergence.
424

Ensure the multicast server is sending all the multicast traffic.

Ensure no static multicast MACs or static multicast routes are configured.

Ensure PIM is not enabled on the switches.
G8052 Application Guide for ENOS 8.4

IGMP Reports/Leaves sent by the hosts do not reach the Mrouter

Ensure that the primary or secondary Mrouter is reachable. If not, the IGMP Reports/Leaves are not forwarded. Note that the Mrouter may not be reachable immediately after a LAG failover/failback.
RS G8052(config)# show ip igmp groups

Ensure the host’s multicast application is started and is sending correct IGMP Reports/Leaves.
RS G8052(config)# show ip igmp groups
RS G8052(config)# show ip igmp counters


The Mrouter is reachable on the incorrect LAG

Check link state. LAG 1 may be down or in STP discarding state.

Check STP convergence and port VLAN membership.

Check IP connectivity between the switch and the configured Mrouter (primary or secondary).
Hosts receive multicast traffic at a lower rate than normal

Ensure a multicast threshold is not configured on the LAGs.
RS G8052(config)# interface port <port id>
RS G8052(config­if)# no storm­control multicast

© Copyright Lenovo 2016
Check link speeds and network congestion.
Chapter 27: Internet Group Management Protocol
425
Additional IGMP Features
The following topics are discussed in this section: 
“FastLeave” on page 426

“IGMP Filtering” on page 426

“Static Multicast Router” on page 427
FastLeave
In normal IGMP operation, when the switch receives an IGMPv2 Leave message, it sends a Group‐Specific Query to determine if any other devices in the same group (and on the same port) are still interested in the specified multicast group traffic. The switch removes the affiliated port from that particular group, if the switch does not receive an IGMP Membership Report within the query‐response‐interval.
With FastLeave enabled on the VLAN, a port can be removed immediately from the port list of the group entry when the IGMP Leave message is received. Note: Only IGMPv2 supports FastLeave. Enable FastLeave on ports that have only one host connected. If more than one host is connected to a port, you may lose some hosts unexpectedly.
Use the following command to enable FastLeave. IGMP Filtering
With IGMP filtering, you can allow or deny certain IGMP groups to be learned on a port.
If access to a multicast group is denied, IGMP Membership Reports from the port are dropped, and the port is not allowed to receive IPv4 multicast traffic from that group. If access to the multicast group is allowed, Membership Reports from the port are forwarded for normal processing.
To configure IGMP filtering, you must globally enable IGMP filtering, define an IGMP filter, assign the filter to a port, and enable IGMP filtering on the port. To define an IGMP filter, you must configure a range of IPv4 multicast groups, choose whether the filter will allow or deny multicast traffic for groups within the range, and enable the filter.
Configuring the Range
Each IGMP filter allows you to set a start and end point that defines the range of IPv4 addresses upon which the filter takes action. Each IPv4 address in the range must be between 224.0.0.0 and 239.255.255.255.
426
G8052 Application Guide for ENOS 8.4
Configuring the Action
Each IGMP filter can allow or deny IPv4 multicasts to the range of IPv4 addresses configured. If you configure the filter to deny IPv4 multicasts, then IGMP Membership Reports from multicast groups within the range are dropped. You can configure a secondary filter to allow IPv4 multicasts to a small range of addresses within a larger range that a primary filter is configured to deny. The two filters work together to allow IPv4 multicasts to a small subset of addresses within the larger range of addresses.
Note: Lower‐numbered filters take precedence over higher‐number filters. For example, the action defined for IGMP filter 1 supersedes the action defined for IGMP filter 2.
Configure IGMP Filtering
1. Enable IGMP filtering on the switch.
RS G8052(config)# ip igmp filtering
2. Define an IGMP filter with IPv4 information.
RS G8052(config)# ip igmp profile 1 range 224.0.0.0 226.0.0.0
RS G8052(config)# ip igmp profile 1 action deny
RS G8052(config)# ip igmp profile 1 enable
3. Assign the IGMP filter to a port.
RS G8052(config)# interface port 3
RS G8052(config­if)# ip igmp profile 1
RS G8052(config­if)# ip igmp filtering
Static Multicast Router
A static Mrouter can be configured for a particular port on a particular VLAN. A static Mrouter does not have to be learned through IGMP Snooping. Any data port can accept a static Mrouter. When you configure a static Mrouter on a VLAN, it replaces any dynamic Mrouters learned through IGMP Snooping. To configure a static multicast router
1. For each Mrouter, configure a port, VLAN, and IGMP version of the multicast router. RS G8052(config)# ip igmp mrouter 5 1 2
2. Verify the configuration. RS G8052(config)# show ip igmp mrouter
© Copyright Lenovo 2016
Chapter 27: Internet Group Management Protocol
427
428
G8052 Application Guide for ENOS 8.4
Chapter 28. Multicast Listener Discovery
Multicast Listener Discovery (MLD) is an IPv6 protocol that a host uses to request multicast data for a multicast group. An IPv6 router uses MLD to discover the presence of multicast listeners (nodes that want to receive multicast packets) on its directly attached links, and to discover specifically the multicast addresses that are of interest to those neighboring nodes.
MLD version 1 is derived from Internet Group Management Protocol version 2 (IGMPv2) and MLDv2 is derived from IGMPv3. MLD uses ICMPv6 (IP Protocol 58) message types. See RFC 2710 and RFC 3810 for details.
MLDv2 protocol, when compared to MLDv1, adds support for source filtering—
the ability for a node to report interest in listening to packets only from specific source addresses, or from all but specific source addresses, sent to a particular multicast address. MLDv2 is interoperable with MLDv1. See RFC 3569 for details on Source‐Specific Multicast (SSM).
The following topics are discussed in this chapter:
© Copyright Lenovo 2016

“MLD Terms” on page 430

“How MLD Works” on page 431

“MLD Capacity and Default Values” on page 434

“Configuring MLD” on page 435
429
MLD Terms
Following are the commonly used MLD terms:

Multicast traffic: Flow of data from one source to multiple destinations.

Group: A multicast stream to which a host can join.

Multicast Router (Mrouter): A router configured to make routing decisions for multicast traffic. The router identifies the type of packet received (unicast or multicast) and forwards the packet to the intended destination.

Querier: An Mrouter that sends periodic query messages. Only one Mrouter on the subnet can be elected as the Querier.

Multicast Listener Query: Messages sent by the Querier. There are three types of queries:

General Query: Sent periodically to learn multicast address listeners from an attached link. G8052 uses these queries to build and refresh the Multicast Address Listener state. General Queries are sent to the link‐scope all‐nodes multicast address (FF02::1), with a multicast address field of 0, and a maximum response delay of query response interval.

Multicast Address Specific Query: Sent to learn if a specific multicast address has any listeners on an attached link. The multicast address field is set to the IPv6 multicast address.

Multicast Address and Source Specific Query: Sent to learn if, for a specified multicast address, there are nodes still listening to a specific set of sources. Supported only in MLDv2.
Note: Multicast Address Specific Queries and Multicast Address and Source Specific Queries are sent only in response to State Change Reports, and never in response to Current State Reports.


430
Multicast Listener Report: Sent by a host when it joins a multicast group, or in response to a Multicast Listener Query sent by the Querier. Hosts use these reports to indicate their current multicast listening state, or changes in the multicast listening state of their interfaces. These reports are of two types:

Current State Report: Contains the current Multicast Address Listening State of the host.

State Change Report: If the listening state of a host changes, the host immediately reports these changes through a State Change Report message. These reports contain either Filter Mode Change records and/or Source List Change records. State Change Reports are retransmitted several times to ensure all Mrouters receive it.
Multicast Listener Done: Sent by a host when it wants to leave a multicast group. This message is sent to the link‐scope all‐routers IPv6 destination address of FF02::2. When an Mrouter receives a Multicast Listener Done message from the last member of the multicast address on a link, it stops forwarding traffic to this multicast address.
G8052 Application Guide for ENOS 8.4
How MLD Works
The software uses the information obtained through MLD to maintain a list of multicast group memberships for each interface and forwards the multicast traffic only to interested listeners.
Without MLD, the switch forwards IPv6 multicast traffic through all ports, increasing network load. Following is an overview of operations when MLD is configured on the G8052:

The switch acts as an Mrouter when MLDv1/v2 is configured and enabled on each of its directly attached links. If the switch has multiple interfaces connected to the same link, it operates the protocol on any one of the interfaces.

If there are multiple Mrouters on the subnet, the Mrouter with the numerically lowest IPv6 address is elected as the Querier.

The Querier sends general queries at short intervals to learn multicast address listener information from an attached link.

Hosts respond to these queries by reporting their per‐interface Multicast Address Listening state, through Current State Report messages sent to a specific multicast address that all MLD routers on the link listen to.

If the listening state of a host changes, the host immediately reports these changes through a State Change Report message.

The Querier sends a Multicast Address Specific Query to verify if hosts are listening to a specified multicast address or not. Similarly, if MLDv2 is configured, the Querier sends a Multicast Address and Source Specific Query to verify, for a specified multicast address, if hosts are listening to a specific set of sources, or not. MLDv2 listener report messages consists of Multicast Address Records:


INCLUDE: to receive packets from source specified in the MLDv2 message

EXCLUDE: to receive packets from all sources except the ones specified in the MLDv2 message
A host can send a State Change Report to indicate its desire to stop listening to a particular multicast address (or source in MLDv2). The Querier then sends a multicast address specific query to verify if there are other listeners of the multicast address. If there aren’t any, the Mrouter deletes the multicast address from its Multicast Address Listener state and stops sending multicast traffic. Similarly in MLDv2, the Mrouter sends a Multicast Address and Source Specific Query to verify if, for a specified multicast address, there are hosts still listening to a specific set of sources.
G8052 supports MLD versions 1 and 2.
Note: MLDv2 operates in version 1 compatibility mode when, in a specific network, not all hosts are configured with MLDv2.
© Copyright Lenovo 2016
Chapter 28: Multicast Listener Discovery
431
How Flooding Impacts MLD
When flood option is disabled, the unknown multicast traffic is discarded if no Mrouters are learned on the switch. You can set the flooding behavior by configuring the flood and cpu options. You can optimize the flooding to ensure that unknown IP multicast (IPMC) data packets are not dropped during the learning phase.
The flooding options include:

flood: Enable hardware flooding in VLAN for the unregistered IPMC; This option is enabled by default.

cpu: Enable sending unregistered IPMC to the Mrouter ports. However, during the learning period, there will be some packet loss. The cpu option is enabled by default. You must ensure that the flood and optflood options are disabled.

optflood: Enable optimized flooding to allow sending the unregistered IPMC to the Mrouter ports without having any packet loss during the learning period; This option is disabled by default; When optflood is enabled, the flood and cpu settings are ignored.
The flooding parameters must be configured per VLAN. Enter the following command to set the flood or cpu option:
RS
RS
RS
RS
G8052(config)# vlan <vlan number>
G8052(config­vlan)# [no] flood
G8052(config­vlan)# [no] cpu
G8052(config­vlan)# [no] optflood
MLD Querier
An Mrouter acts as a Querier and periodically (at short query intervals) sends query messages in the subnet. If there are multiple Mrouters in the subnet, only one can be the Querier. All Mrouters on the subnet listen to the messages sent by the multicast address listeners, and maintain the same multicast listening information state.
All MLDv2 queries are sent with the FE80::/64 link‐local source address prefix.
Querier Election
Only one Mrouter can be the Querier per subnet. All other Mrouters will be non‐Queriers. MLD versions 1 and 2 elect the Mrouter with the numerically lowest IPv6 address as the Querier. If the switch is configured as an Mrouter on a subnet, it also acts as a Querier by default and sends multiple general queries. If the switch receives a general query from another Querier with a numerically lower IPv6 address, it sets the other querier present timer to the other querier present timeout, and changes its state to non‐Querier. When the other querier present timer expires, it regains the Querier state and starts sending general queries.
Note: When MLD Querier is enabled on a VLAN, the switch performs the role of an MLD Querier only if it meets the MLD Querier election criteria.
432
G8052 Application Guide for ENOS 8.4
Dynamic Mrouters
The switch learns Mrouters on the ingress VLANs of the MLD‐enabled interface. All report or done messages are forwarded to these Mrouters. By default, the option of dynamically learning Mrouters is disabled. To enable it, use the following command:
RS G8052(config)# interface ip <interface number>
RS G8052(config­ip­if)# ipv6 mld dmrtr enable
© Copyright Lenovo 2016
Chapter 28: Multicast Listener Discovery
433
MLD Capacity and Default Values
Table 32 lists the maximum and minimum values of the G8052 variables. Table 32. G8052 Capacity Table
Variable
Maximum Value
IPv6 Multicast Entries
256
IPv6 Interfaces for MLD
8
Table 33 lists the default settings for MLD features and variables. Table 33. MLD Timers and Default Values
Field
Default Value
Robustness Variable (RV) 2
Query Interval (QI)
125 seconds
Query Response Interval (QRI)
10 seconds
Multicast Address Listeners Interval (MALI)
260 seconds [derived: RV*QI+QRI]
Other Querier Present Interval [OQPT]
255 seconds [derived: RV*QI + ½ QRI]
Start up Query Interval [SQI]
31.25 seconds [derived: ¼ * QI]
Startup Query Count [SQC]
2 [derived: RV]
Last Listener Query Interval [LLQI] 1 second Last Listener Query Count [LLQC]
2 [derived: RV]
Last Listener Query Time [LLQT]
2 seconds [derived: LLQI * LLQT]
Older Version Querier Present Timeout: 260 seconds [derived: RV*QI+ QRI]
[OVQPT]
Older Version Host Present Interval [OVHPT]
434
G8052 Application Guide for ENOS 8.4
260 seconds [derived: RV* QI+QRI]
Configuring MLD
Following are the steps to enable MLD and configure the interface parameters:
1. Turn on MLD globally.
RS G8052(config)# ipv6 mld
RS G8052(config­router­mld)# enable
RS G8052(config­router­mld)# exit
2. Create an IPv6 interface.
RS
RS
RS
RS
G8052(config)# interface ip 2
G8052(config­ip­if)# enable
G8052(config­ip­if)# ipv6 address 2002:1:0:0:0:0:0:3
G8052(config­ip­if)# ipv6 prefixlen 64
3. Enable MLD on the IPv6 interface. RS G8052(config­ip­if)# ipv6 mld enable
4. Configure the MLD parameters on the interface: version, robustness, query response interval, MLD query interval, and last listener query interval.
© Copyright Lenovo 2016
RS G8052(config­ip­if)# ipv6 mld version <1‐2>
(MLD version)
RS G8052(config­ip­if)# ipv6 mld robust <1‐10>
(Robustness)
RS G8052(config­ip­if)# ipv6 mld qri <1‐256>
(In seconds)
RS G8052(config­ip­if)# ipv6 mld qintrval <1‐608>
(In seconds)
RS G8052(config­ip­if)# ipv6 mld llistnr <1‐32>
(In seconds)
Chapter 28: Multicast Listener Discovery
435
436
G8052 Application Guide for ENOS 8.4
Chapter 29. Border Gateway Protocol
Border Gateway Protocol (BGP) is an Internet protocol that enables routers on an IPv4 network to share and advertise routing information with each other about the segments of the IPv4 address space they can access within their network and with routers on external networks. BGP allows you to decide what is the “best” route for a packet to take from your network to a destination on another network rather than simply setting a default route from your border router(s) to your upstream provider(s). BGP is defined in RFC 1771.
RackSwitch G8052es can advertise their IP interfaces and IPv4 addresses using BGP and take BGP feeds from as many as 12 BGP router peers. This allows more resilience and flexibility in balancing traffic from the Internet.
Note: Lenovo Enterprise Network Operating System 8.4 does not support IPv6 for BGP.
The following topics are discussed in this section:
© Copyright Lenovo 2016

“Internal Routing Versus External Routing” on page 438

“Forming BGP Peer Routers” on page 443

“Loopback Interfaces” on page 444

“What is a Route Map?” on page 444

“Aggregating Routes” on page 448

“Redistributing Routes” on page 448

“BGP Attributes” on page 450

“Selecting Route Paths in BGP” on page 452

“BGP Failover Configuration” on page 453

“Default Redistribution and Route Aggregation Example” on page 455
437
Internal Routing Versus External Routing
To ensure effective processing of network traffic, every router on your network needs to know how to send a packet (directly or indirectly) to any other location/destination in your network. This is referred to as internal routing and can be done with static routes or using active, internal dynamic routing protocols, such as RIP, RIPv2, and OSPF.
Static routes must have a higher degree of precedence than dynamic routing protocols. If the destination route is not in the route cache, the packets are forwarded to the default gateway which may be incorrect if a dynamic routing protocol is enabled.
It is also useful to tell routers outside your network (upstream providers or peers) about the routes you can access in your network. External networks (those outside your own) that are under the same administrative control are referred to as autonomous systems (AS). Sharing of routing information between autonomous systems is known as external routing.
External BGP (eBGP) is used to exchange routes between different autonomous systems whereas internal BGP (iBGP) is used to exchange routes within the same autonomous system. An iBGP is a type of internal routing protocol you can use to do active routing inside your network. It also carries AS path information, which is important when you are an ISP or doing BGP transit.
The iBGP peers have to maintain reciprocal sessions to every other iBGP router in the same AS (in a full‐mesh manner) to propagate route information throughout the AS. If the iBGP session shown between the two routers in AS 20 was not present (as indicated in Figure 32), the top router would not learn the route to AS 50, and the bottom router would not learn the route to AS 11, even though the two AS 20 routers are connected via the RackSwitch G8052.
Figure 32. iBGP and eBGP
Internet
When there are many iBGP peers, having a full‐mesh configuration results in large number of sessions between the iBGP peers. In such situations, configuring a route reflector eliminates the full‐mesh configuration requirement, prevents route propagation loops, and provides better scalability to the peers. For details, see “Route Reflector” on page 439.
438
G8052 Application Guide for ENOS 8.4
Typically, an AS has one or more border routers—peer routers that exchange routes with other ASs—and an internal routing scheme that enables routers in that AS to reach every other router and destination within that AS. When you advertise routes to border routers on other autonomous systems, you are effectively committing to carry data to the IPv4 space represented in the route being advertised. For example, if you advertise 192.204.4.0/24, you are declaring that if another router sends you data destined for any address in 192.204.4.0/24, you know how to carry that data to its destination.
Route Reflector
The Enterprise NOS implementation conforms to the BGP Route Reflection specification defined in RFC 4456.
As per RFC 1771 specification, a route received from an iBGP peer cannot be advertised to another iBGP peer. This makes it mandatory to have full‐mesh iBGP sessions between all BGP routers within an AS. A route reflector—a BGP router—
breaks this iBGP loop avoidance rule. It does not affect the eBGP behavior. A route reflector is a BGP speaker that advertises a route learnt from an iBGP peer to another iBGP peer. The advertised route is called the reflected route.
A route reflector has two groups of internal peers: clients and non‐clients. A route reflector reflects between these groups and among the clients. The non‐client peers must be fully meshed. The route reflector and its clients form a cluster.
When a route reflector receives a route from an iBGP peer, it selects the best path based on its path selection rule. It then does the following based on the type of peer it received the best path from:
© Copyright Lenovo 2016

A route received from a non‐client iBGP peer is reflected to all clients.

A route received from an iBGP client peer is reflected to all iBGP clients and iBGP non‐clients. Chapter 29: Border Gateway Protocol
439
In Figure 33, the G8052 is configured as a route reflector. All clients and non‐clients are in the same AS. Figure 33. iBGP Route Reflector
Cluster
RR Client
RR Client
iBGP
iBGP
Route Reflector
iBGP
iBGP
iBGP
RR Non-Client
RR Non-Client
The following attributes are used by the route reflector functionality:
440

ORIGINATOR ID: BGP identifier (BGP router ID) of the route originator in the local AS. If the route does not have the ORIGINATOR ID attribute (it has not been reflected before), the router ID of the iBGP peer from which the route has been received is copied into the Originator ID attribute.This attribute is never modified by subsequent route reflectors. A router that identifies its own ID as the ORIGINATOR ID, it ignores the route. 
CLUSTER LIST: Sequence of the CLUSTER ID (the router ID) values representing the reflection path that the route has passed. The value configured with the cluster­id command (or the router ID of the route reflector if the cluster­id is not configured) is prepended to the Cluster list attribute. If a route reflector detects its own CLUSTER ID in the CLUSTER LIST, it ignores the route. Up to 10 CLUSTER IDs can be added to a CLUSTER LIST.
G8052 Application Guide for ENOS 8.4
Configuring Route Reflection
Route reflection functionality can be configured as follows:
1. Configure an AS. RS G8052(config)# router bgp
RS G8052(config­router­bgp)# as 22
RS G8052(config­router­bgp)# enable
2. Configure a route reflector client. RS
RS
RS
RS
G8052(config­router­bgp)# neighbor 2 remote­address 10.1.50.1
G8052(config­router­bgp)# neighbor 2 remote­as 22
G8052(config­router­bgp)# neighbor 2 route­reflector­client
G8052(config­router­bgp)# no neighbor 2 shutdown
Note: When a client is configured on the G8052, the switch automatically gets configured as a route reflector.
3. Verify configuration. RS G8052(config)# show ip bgp neighbor 2 information
BGP Peer 2 Information:
2: 10.1.50.1 , version 0, TTL 255, TTL Security hops 0
Remote AS: 0, Local AS: 22, Link type: IBGP
Remote router ID: 0.0.0.0, Local router ID: 9.9.9.9
next­hop­self disabled
RR client enabled BGP status: connect, Old status: connect
Total received packets: 0, Total sent packets: 0
Received updates: 0, Sent updates: 0
Keepalive: 0, Holdtime: 0, MinAdvTime: 60
LastErrorCode: unknown(0), LastErrorSubcode: unspecified(0)
Established state transitions: 0
Once configured as a route reflector, the switch, by default, passes routes between clients. If required, you can disable this by using the following command: RS G8052(config­router­bgp)# no client­to­client reflection
You can view the route reflector BGP attributes attached to a BGP route using the following command: RS G8052(config­router­bgp)# show ip bgp information 5.0.0.0 255.255.255.0
BGP routing table entry for 5.0.0.0/255.255.255.0
Paths: (1 available, best #1)
Multipath: eBGP
Local
30.1.1.1 (metric 0) from 22.22.1.1(17.17.17.17)
Origin: IGP, localpref 0, valid, internal, best
Originator: 1.16.0.195
Cluster list: 17.17.17.17
© Copyright Lenovo 2016
Chapter 29: Border Gateway Protocol
441
You can view BGP advertised routes to a specific neighbor or to all neighbors using the command:
[Prompt](config)# show ip bgp neighbor advertised­routes
Restrictions
Consider the following restrictions when configuring route reflection functionality:
442

When a CLUSTER ID is changed, all iBGP sessions are restarted.

When a route reflector client is enabled/disabled, the session is restarted.
G8052 Application Guide for ENOS 8.4
Forming BGP Peer Routers
Two BGP routers become peers or neighbors once you establish a TCP connection between them.
For each new route, if a peer is interested in that route (for example, if a peer would like to receive your static routes and the new route is static), an update message is sent to that peer containing the new route. For each route removed from the route table, if the route has already been sent to a peer, an update message containing the route to withdraw is sent to that peer.
For each Internet host, you must be able to send a packet to that host, and that host has to have a path back to you. This means that whoever provides Internet connectivity to that host must have a path to you. Ultimately, this means that they must “hear a route” which covers the section of the IPv4 space you are using; otherwise, you will not have connectivity to the host in question.
© Copyright Lenovo 2016
Chapter 29: Border Gateway Protocol
443
Loopback Interfaces
In many networks, multiple connections may exist between network devices. In such environments, it may be useful to employ a loopback interface for a common BGP router address, rather than peering the switch to each individual interface.
Note: To ensure that the loopback interface is reachable from peer devices, it must be advertised using an interior routing protocol (such as OSPF), or a static route must be configured on the peer.
To configure an existing loopback interface for BGP neighbor, use the following commands:
RS G8052(config)# router bgp
RS G8052(config­router­bgp)# neighbor <#> update­source loopback <1‐5>
RS G8052(config­router­bgp)# exit
What is a Route Map?
A route map is used to control and modify routing information. Route maps define conditions for redistributing routes from one routing protocol to another or controlling routing information when injecting it in and out of BGP. For example, a route map is used to set a preference value for a specific route from a peer router and another preference value for all other routes learned via the same peer router. For example, the following command is used to enter the Route Map mode for defining a route map:
RS G8052(config)# route­map <map number>(Select a route map)
A route map allows you to match attributes, such as metric, network address, and AS number. It also allows users to overwrite the local preference metric and to append the AS number in the AS route. See “BGP Failover Configuration” on page 453.
Enterprise NOS allows you to configure 255 route maps. Each route map can have up to 32 access lists. Each access list consists of a network filter. A network filter defines an IPv4 address and subnet mask of the network that you want to include in the filter. Figure 34 illustrates the relationship between route maps, access lists, and network filters.
444
G8052 Application Guide for ENOS 8.4
Figure 34. Distributing Network Filters in Access Lists and Route Maps Route Maps
Network Filter
(rmap)
(nwf)
Access Lists
(alist)
Route Map 1
Route Map 2
----------------------------Route Map 255
1
-------
1
32
8
1
------32
9
16
1
-------
249
32
256
Next Hop Peer IP Address
Next hop peer IP address can be configured only for route maps used in BGP. When a route map is applied on ingress, the next hop of learnt routes is replaced with peer IP address. When applied on egress, the next hop of the redistributed routes is replaced with the local IP address. RS G8052(config)# route­map <map number>
RS G8052(config­router­map)# set ip next­hop <peer IP address>
Incoming and Outgoing Route Maps
You can have two types of route maps: incoming and outgoing. A BGP peer router can be configured to support up to eight route maps in the incoming route map list and outgoing route map list.
If a route map is not configured in the incoming route map list, the router imports all BGP updates. If a route map is configured in the incoming route map list, the router ignores all unmatched incoming updates. If you set the action to deny, you must add another route map to permit all unmatched updates.
Route maps in an outgoing route map list behave similar to route maps in an incoming route map list. If a route map is not configured in the outgoing route map list, all routes are advertised or permitted. If a route map in the outgoing route map list is set to permit, matched routes are advertised and unmatched routes are ignored.
© Copyright Lenovo 2016
Chapter 29: Border Gateway Protocol
445
Precedence
You can set a priority to a route map by specifying a precedence value with the following command (Route Map mode): RS G8052(config)# route­map <map number>(Select a route map)
RS G8052(config­route­map)# precedence <1‐255>(Specify a precedence)
RS G8052(config­route­map)# exit
The smaller the value the higher the precedence. If two route maps have the same precedence value, the smaller number has higher precedence.
Configuration Overview
To configure route maps, you need to do the following:
1. Define a network filter. RS G8052(config)# ip match­address 1 <IPv4 address> <IPv4 subnet mask> RS G8052(config)# ip match­address 1 enable
Enter a filter number from 1 to 256. Specify the IPv4 address and subnet mask of the network that you want to match. Enable the network filter. You can distribute up to 256 network filters among 64 route maps each containing 32 access lists.
Steps 2 and 3 are optional, depending on the criteria that you want to match. In Step 2, the network filter number is used to match the subnets defined in the network filter. In Step 3, the autonomous system number is used to match the subnets. Or, you can use both (Step 2 and Step 3) criteria: access list (network filter) and access path (AS filter) to configure the route maps.
2. (Optional) Define the criteria for the access list and enable it.
Specify the access list and associate the network filter number configured in Step 1.
RS
RS
RS
RS
RS
G8052(config)# route­map 1
G8052(config­route­map)# access­list 1 match­address 1
G8052(config­route­map)# access­list 1 metric <metric value> G8052(config­route­map)# access­list 1 action deny
G8052(config­route­map)# access­list 1 enable
3. (Optional) Configure the AS filter attributes. RS G8052(config­route­map)# as­path­list 1 as 1
RS G8052(config­route­map)# as­path­list 1 action deny
RS G8052(config­route­map)# as­path­list 1 enable
4. Set up the BGP attributes.
If you want to overwrite the attributes that the peer router is sending, define the following BGP attributes:
446

Specify up to 32 AS numbers that you want to prepend to a matched route. Use one space between each of the entries in the list.

Specify the local preference for the matched route.
G8052 Application Guide for ENOS 8.4

Specify the Multi Exit Discriminator (MED) metric for the matched route. RS G8052(config­route­map)# as­path­preference <AS number list (up to 32 entries)>
RS G8052(config­route­map)# local­preference <local preference value>
RS G8052(config­route­map)# metric <metric value>
5. Enable the route map.
RS G8052(config­route­map)# enable
RS G8052(config­route­map)# exit
6. Turn BGP on.
RS G8052(config)# router bgp
RS G8052(config­router­bgp)# enable
7. Assign the route map to a peer router.
Select the peer router and then add the route map to the incoming route map list,
RS G8052(config­router­bgp)# neighbor 1 route­map in <1‐255>
or to the outgoing route map list.
RS G8052(config­router­bgp)# neighbor 1 route­map out <1‐255
8. Exit Router BGP mode.
RS G8052(config­router­bgp)# exit
© Copyright Lenovo 2016
Chapter 29: Border Gateway Protocol
447
Aggregating Routes
Aggregation is the process of combining several different routes in such a way that a single route can be advertised, which minimizes the size of the routing table. You can configure aggregate routes in BGP either by redistributing an aggregate route into BGP or by creating an aggregate entry in the BGP routing table.
To define an aggregate route in the BGP routing table, use the following commands: RS G8052(config)# router bgp
RS G8052(config­router­bgp)# aggregate­address <1‐16> <IPv4 address> <mask>
RS G8052(config­router­bgp)# aggregate­address <1‐16> enable
An example of creating a BGP aggregate route is shown in “Default Redistribution and Route Aggregation Example” on page 455.
Redistributing Routes
In addition to running multiple routing protocols simultaneously, ENOS software can redistribute information from one routing protocol to another. For example, you can instruct the switch to use BGP to re‐advertise static routes. This applies to all of the IP‐based routing protocols.
You can also conditionally control the redistribution of routes between routing domains by defining a method known as route maps between the two domains. For more information on route maps, see “What is a Route Map?” on page 444. Redistributing routes is another way of providing policy control over whether to export OSPF routes, fixed routes, and static routes. For an example configuration, see “Default Redistribution and Route Aggregation Example” on page 455.
Default routes can be configured using the following methods:
448

Import

Originate—The router sends a default route to peers if it does not have any default routes in its routing table.

Redistribute—Default routes are either configured through the default gateway or learned via other protocols and redistributed to peer routers. If the default routes are from the default gateway, enable the static routes because default routes from the default gateway are static routes. Similarly, if the routes are learned from another routing protocol, make sure you enable that protocol for redistribution.

None
G8052 Application Guide for ENOS 8.4
BGP Communities
BGP communities are attribute tags that allow controlled distribution of routing information based on an agreement between BGP peers. Communities are commonly used by transit service providers to enable peering customers to choose specific routing destinations for their outgoing routes. The transit service provider would typically publish a list of well‐known or proprietary communities along with their descriptions, and take it upon itself to advertise incoming routes accordingly. For instance, an ISP may advertise that incoming routes tagged with community XY:01 will be advertised only to European peers while incoming routes tagged with community XY:02 will be advertised only to Asian peers.
The RackSwitch G8052 can be configured to manage the community tags applied to the outgoing route updates. It does not, however, modify any routing decisions based on the community tags.
Up to 32 community tags can be applied to prefixes that pass a route‐map. Valid values are between 0:0 and 65535:65535. Newly added communities will be appended to any existing configured communities. To append communities to prefixes that pass the route‐map, use the following commands:
RS G8052(config)# route­map <map number>
RS G8052(config­route­map)# set community {aa:nn [aa:nn]}
To remove all community tags from prefixes that pass the route‐map, use the following command:
RS G8052(config­route­map)# set community none
To remove configured communities on a routemap, use the following command:
RS G8052(config­route­map)# no set community
Prefixes with communities are propagated unchanged if there is no routemap that alters the community attribute and if the neighbor has community tags forwarding enabled.
To enable or disable community tags forwarding for specific neighbors or neighbor groups, use the following commands:
RS G8052(config)# router bgp
RS G8052(config­router­bgp)# neighbor 5 send­community
RS G8052(config­router­bgp)# no neighbor 6 send­community
RS G8052(config­router­bgp)# neighbor group 1 send­community
RS G8052(config­router­bgp)# no neighbor group 2 send­community
© Copyright Lenovo 2016
Chapter 29: Border Gateway Protocol
449
BGP Attributes
The following BGP attributes are discussed in this section: Local preference, metric (Multi‐Exit Discriminator), and Next hop.
Local Preference Attribute
When there are multiple paths to the same destination, the local preference attribute indicates the preferred path. The path with the higher preference is preferred (the default value of the local preference attribute is 100). Unlike the weight attribute, which is only relevant to the local router, the local preference attribute is part of the routing update and is exchanged among routers in the same AS.
The local preference attribute can be set in one of two ways:

The following commands use the BGP default local preference method, affecting the outbound direction only. RS G8052(config)# router bgp
RS G8052(config_router_bgp)# local­preference
RS G8052(config_router_bgp)# exit

The following commands use the route map local preference method, which affects both inbound and outbound directions. RS G8052(config)# route­map 1
RS G8052(config_route_map)# local­preference
RS G8052(config_router_map)# exit
Metric (Multi-Exit Discriminator) Attribute
This attribute is a hint to external neighbors about the preferred path into an AS when there are multiple entry points. A lower metric value is preferred over a higher metric value. The default value of the metric attribute is 0.
Unlike local preference, the metric attribute is exchanged between ASs; however, a metric attribute that comes into an AS does not leave the AS.
When an update enters the AS with a certain metric value, that value is used for decision making within the AS. When BGP sends that update to another AS, the metric is reset to 0.
Unless otherwise specified, the router compares metric attributes for paths from external neighbors that are in the same AS.
450
G8052 Application Guide for ENOS 8.4
Next Hop Attribute
BGP routing updates sent to a neighbor contain the next hop IP address used to reach a destination. In eBGP, the edge router, by default, sends its own IP address as the next hop address. However, this can sometimes cause routing path failures in Non‐Broadcast Multiaccess Networks (NBMA) and when the edge router sends iBGP updates.
To avoid routing failures, you can manually configure the next hop IP address. In case of NBMA networks, you can configure the external BGP speaker to advertise its own IP address as the next hop. In case of iBGP updates, you can configure the edge iBGP router to send its IP address as the next hop. Next hop can be configured on a BGP peer. Use the following command: 
Next Hop for a BGP Peer RS G8052(config)# router bgp
RS G8052(config­router­bgp)# neighbor <number> next­hop­self
© Copyright Lenovo 2016
Chapter 29: Border Gateway Protocol
451
Selecting Route Paths in BGP
BGP selects only one path as the best path. It does not rely on metric attributes to determine the best path. When the same network is learned via more than one BGP peer, BGP uses its policy for selecting the best route to that network. The BGP implementation on the G8052 uses the following criteria to select a path when the same route is received from multiple peers.
1. Local fixed and static routes are preferred over learned routes.
2. With iBGP peers, routes with higher local preference values are selected.
3. In the case of multiple routes of equal preference, the route with lower AS path weight is selected.
AS path weight = 128 x AS path length (number of autonomous systems traversed).
4. In the case of equal weight and routes learned from peers that reside in the same AS, the lower metric is selected.
Note: A route with a metric is preferred over a route without a metric.
5. The lower cost to the next hop of routes is selected.
6. In the case of equal cost, the eBGP route is preferred over iBGP.
7. If all routes have same route type (eBGP or iBGP), the route with the lower router ID is selected.
When the path is selected, BGP puts the selected path in its routing table and propagates the path to its neighbors.
Equal Cost Multi-Path
BGP can be configured to load balance the traffic over multiple paths if first six steps in path selection are identical and the next‐hop of the route differs.
Multipath Relax
BGP multipath relax functionality allows load balancing across routes with different autonomous system paths, but equal in length (same as‐path length). With this option disabled, both autonomous system paths and as‐path length must be identical for load sharing. This functionality can be enabled using the command: RS G8052(config­router­bgp)# bestpath as­path multipath­relax
Note: The BGP multipath relax feature does not apply to the G8052 in stacking mode..
452
G8052 Application Guide for ENOS 8.4
BGP Failover Configuration
Use the following example to create redundant default gateways for a G8052 at a Web Host/ISP site, eliminating the possibility, if one gateway goes down, that requests will be forwarded to an upstream router unknown to the switch.
As shown in Figure 35, the switch is connected to ISP 1 and ISP 2. The customer negotiates with both ISPs to allow the switch to use their peer routers as default gateways. The ISP peer routers will then need to announce themselves as default gateways to the G8052.
Figure 35. BGP Failover Configuration Example
Switch
IP: 200.200.200.1
IP: 210.210.210.1
BladeCenter
Server 1
IP: 200.200.200.10
Server 2
IP: 200.200.200.11
On the G8052, one peer router (the secondary one) is configured with a longer AS path than the other, so that the peer with the shorter AS path will be seen by the switch as the primary default gateway. ISP 2, the secondary peer, is configured with a metric of “3,” thereby appearing to the switch to be three router hops away.
1. Define the VLANs.
For simplicity, both default gateways are configured in the same VLAN in this example. The gateways could be in the same VLAN or different VLANs.
RS G8052(config)# vlan 1
© Copyright Lenovo 2016
Chapter 29: Border Gateway Protocol
453
2. Define the IP interfaces with IPv4 addresses.
The switch will need an IP interface for each default gateway to which it will be connected. Each interface must be placed in the appropriate VLAN. These interfaces will be used as the primary and secondary default gateways for the switch.
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip address 200.200.200.1
G8052(config­ip­if)# ip netmask 255.255.255.0
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
G8052(config)# interface ip 2
G8052(config­ip­if)# ip address 210.210.210.1
G8052(config­ip­if)# ip netmask 255.255.255.0
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
3. Enable IP forwarding.
IP forwarding is turned on by default and is used for VLAN‐to‐VLAN (non‐BGP) routing. Make sure IP forwarding is on if the default gateways are on different subnets or if the switch is connected to different subnets and those subnets need to communicate through the switch (which they almost always do).
RS G8052(config)# ip routing
Note: To help eliminate the possibility for a Denial of Service (DoS) attack, the forwarding of directed broadcasts is disabled by default.
4. Configure BGP peer router 1 and 2 with IPv4 addresses.
RS G8052(config)# router bgp
RS G8052RS G8052(config­router­bgp)# neighbor 1 remote­address 200.200.200.2
RS G8052(config­router­bgp)# neighbor 1 remote­as 100
RS G8052(config­router­bgp)# no neighbor 1 shutdown
RS G8052RS G8052(config­router­bgp)# neighbor 2 remote­address 210.210.210.2
RS G8052(config­router­bgp)# neighbor 2 remote­as 200
RS G8052(config­router­bgp)# no neighbor 2 shutdown
454
G8052 Application Guide for ENOS 8.4
Default Redistribution and Route Aggregation Example
This example shows you how to configure the switch to redistribute information from one routing protocol to another and create an aggregate route entry in the BGP routing table to minimize the size of the routing table.
As illustrated in Figure 36, you have two peer routers: an internal and an external peer router. Configure the G8052 to redistribute the default routes from AS 200 to AS 135. At the same time, configure for route aggregation to allow you to condense the number of routes traversing from AS 135 to AS 200.
Figure 36. Route Aggregation and Default Route Redistribution
Switch
10.1.1.135
1. Configure the IP interface.
2. Configure the AS number (AS 135) and router ID (10.1.1.135).
RS
RS
RS
RS
G8052(config)# router bgp
G8052(config­router­bgp)# as 135
G8052(config­router­bgp)# exit
G8052(config)# ip router­id 10.1.1.135 3. Configure internal peer router 1 and external peer router 2 with IPv4 addresses.
RS
RS
RS
RS
RS
RS
RS
G8052(config)# router bgp
G8052RS G8052(config­router­bgp)# neighbor 1 remote­address 10.1.1.4
G8052(config­router­bgp)# neighbor 1 remote­as 135
G8052(config­router­bgp)# no neighbor 1 shutdown
G8052RS G8052(config­router­bgp)# neighbor 2 remote­address 20.20.20.2
G8052(config­router­bgp)# neighbor 2 remote­as 200
G8052(config­router­bgp)# no neighbor 2 shutdown
4. Configure redistribution for Peer 1.
RS G8052(config­router­bgp)# neighbor 1 redistribute default­action redistribute
RS G8052(config­router­bgp)# neighbor 1 redistribute fixed
© Copyright Lenovo 2016
Chapter 29: Border Gateway Protocol
455
5. Configure aggregation policy control.
Configure the IPv4 routes that you want aggregated.
RS G8052(config­router­bgp)# aggregate­address 1 135.0.0.0 255.0.0.0
RS G8052(config­router­bgp)# aggregate­address 1 enable
456
G8052 Application Guide for ENOS 8.4
Chapter 30. Open Shortest Path First
Lenovo Enterprise Network Operating System supports the Open Shortest Path First (OSPF) routing protocol. The Enterprise NOS implementation conforms to the OSPF version 2 specifications detailed in Internet RFC 1583, and OSPF version 3 specifications in RFC 5340. The following sections discuss OSPF support for the RackSwitch G8052:

“OSPFv2 Overview” on page 458. This section provides information on OSPFv2 concepts, such as types of OSPF areas, types of routing devices, neighbors, adjacencies, link state database, authentication, and internal versus external routing.

“OSPFv2 Implementation in Enterprise NOS” on page 463. This section describes how OSPFv2 is implemented in ENOS, such as configuration parameters, electing the designated router, summarizing routes, defining route maps and so forth.

“OSPFv2 Configuration Examples” on page 473. This section provides step‐by‐step instructions on configuring different OSPFv2 examples:

© Copyright Lenovo 2016

Creating a simple OSPF domain

Creating virtual links

Summarizing routes
“OSPFv3 Implementation in Enterprise NOS” on page 482. This section describes differences and additional features found in OSPFv3.
457
OSPFv2 Overview
OSPF is designed for routing traffic within a single IP domain called an Autonomous System (AS). The AS can be divided into smaller logical units known as areas.
All routing devices maintain link information in their own Link State Database (LSDB). OSPF allows networks to be grouped together into an area. The topology of an area is hidden from the rest of the AS, thereby reducing routing traffic. Routing within an area is determined only by the area’s own topology, thus protecting it from bad routing data. An area can be generalized as an IP subnetwork. The following sections describe key OSPF concepts.
Types of OSPF Areas
An AS can be broken into logical units known as areas. In any AS with multiple areas, one area must be designated as area 0, known as the backbone. The backbone acts as the central OSPF area. All other areas in the AS must be connected to the backbone. Areas inject summary routing information into the backbone, which then distributes it to other areas as needed.
As shown in Figure 37, OSPF defines the following types of areas:
458

Stub Area—an area that is connected to only one other area. External route information is not distributed into stub areas.

Not‐So‐Stubby‐Area (NSSA)—similar to a stub area with additional capabilities. Routes originating from within the NSSA can be propagated to adjacent transit and backbone areas. External routes from outside the AS can be advertised within the NSSA but can be configured to not be distributed into other areas.

Transit Area—an area that carries data traffic which neither originates nor terminates in the area itself.
G8052 Application Guide for ENOS 8.4
Figure 37. OSPF Area Types
Backbone
Area 0
(Also a Transit Area)
ABR
ABR
ABR
Internal LSA
Routes
Stub Area
Not-So-Stubby Area
(NSSA)
No External Routes
from Backbone
Transit Area
Virtual
Link
ABR
External LSA
Routes
ASBR
Non-OSPF Area
RIP/BGP AS
ABR = Area Border Router
ASBR = Autonomous System
Boundary Router
Stub Area, NSSA,
or Transit Area
Connected to Backbone
via Virtual Link
Types of OSPF Routing Devices
As shown in Figure 38, OSPF uses the following types of routing devices:
© Copyright Lenovo 2016

Internal Router (IR)—a router that has all of its interfaces within the same area. IRs maintain LSDBs identical to those of other routing devices within the local area.

Area Border Router (ABR)—a router that has interfaces in multiple areas. ABRs maintain one LSDB for each connected area and disseminate routing information between areas.

Autonomous System Boundary Router (ASBR)—a router that acts as a gateway between the OSPF domain and non‐OSPF domains, such as RIP, BGP, and static routes.
Chapter 30: Open Shortest Path First
459
Figure 38. OSPF Domain and an Autonomous System
OSPF Autonomous System
Backbone
Area 0
BGP
External
Routes
Area 3
Inter-Area Routes
(Summary Routes)
ASBR
ABR
RIP
ABR
ASBR
Area 1
ABR
Internal
Router
Area 2
Neighbors and Adjacencies
In areas with two or more routing devices, neighbors and adjacencies are formed.
Neighbors are routing devices that maintain information about each others’ state. To establish neighbor relationships, routing devices periodically send hello packets on each of their interfaces. All routing devices that share a common network segment, appear in the same area, and have the same health parameters (hello and dead intervals) and authentication parameters respond to each other’s hello packets and become neighbors. Neighbors continue to send periodic hello packets to advertise their health to neighbors. In turn, they listen to hello packets to determine the health of their neighbors and to establish contact with new neighbors.
The hello process is used for electing one of the neighbors as the network segment’s Designated Router (DR) and one as the network segment’s Backup Designated Router (BDR). The DR is adjacent to all other neighbors on that specific network segment and acts as the central contact for database exchanges. Each neighbor sends its database information to the DR, which relays the information to the other neighbors.
The BDR is adjacent to all other neighbors (including the DR). Each neighbor sends its database information to the BDR just as with the DR, but the BDR merely stores this data and does not distribute it. If the DR fails, the BDR will take over the task of distributing database information to the other neighbors.
The Link-State Database
OSPF is a link‐state routing protocol. A link represents an interface (or routable path) from the routing device. By establishing an adjacency with the DR, each routing device in an OSPF area maintains an identical Link‐State Database (LSDB) describing the network topology for its area.
Each routing device transmits a Link‐State Advertisement (LSA) on each of its active interfaces. LSAs are entered into the LSDB of each routing device. OSPF uses flooding to distribute LSAs between routing devices. Interfaces may also be passive. Passive interfaces send LSAs to active interfaces, but do not receive LSAs, hello 460
G8052 Application Guide for ENOS 8.4
packets, or any other OSPF protocol information from active interfaces. Passive interfaces behave as stub networks, allowing OSPF routing devices to be aware of devices that do otherwise participate in OSPF (either because they do not support it, or because the administrator chooses to restrict OSPF traffic exchange or transit).
When LSAs result in changes to the routing device’s LSDB, the routing device forwards the changes to the adjacent neighbors (the DR and BDR) for distribution to the other neighbors.
OSPF routing updates occur only when changes occur, instead of periodically. For each new route, if a neighbor is interested in that route (for example, if configured to receive static routes and the new route is indeed static), an update message containing the new route is sent to the adjacency. For each route removed from the route table, if the route has already been sent to a neighbor, an update message containing the route to withdraw is sent.
© Copyright Lenovo 2016
Chapter 30: Open Shortest Path First
461
The Shortest Path First Tree
The routing devices use a link‐state algorithm (Dijkstra’s algorithm) to calculate the shortest path to all known destinations, based on the cumulative cost required to reach the destination.
The cost of an individual interface in OSPF is an indication of the overhead required to send packets across it.
Internal Versus External Routing
To ensure effective processing of network traffic, every routing device on your network needs to know how to send a packet (directly or indirectly) to any other location/destination in your network. This is referred to as internal routing and can be done with static routes or using active internal routing protocols, such as OSPF, RIP, or RIPv2.
It is also useful to tell routers outside your network (upstream providers or peers) about the routes you have access to in your network. Sharing of routing information between autonomous systems is known as external routing.
Typically, an AS will have one or more border routers (peer routers that exchange routes with other OSPF networks) as well as an internal routing system enabling every router in that AS to reach every other router and destination within that AS.
When a routing device advertises routes to boundary routers on other autonomous systems, it is effectively committing to carry data to the IP space represented in the route being advertised. For example, if the routing device advertises 192.204.4.0/24, it is declaring that if another router sends data destined for any address in the 192.204.4.0/24 range, it will carry that data to its destination.
462
G8052 Application Guide for ENOS 8.4
OSPFv2 Implementation in Enterprise NOS
ENOS supports a single instance of OSPF and up to 4K routes on the network. The following sections describe OSPF implementation in ENOS:









“Configurable Parameters” on page 463
“Defining Areas” on page 464
“Interface Cost” on page 466
“Electing the Designated Router and Backup” on page 466
“Summarizing Routes” on page 466
“Default Routes” on page 467
“Virtual Links” on page 467
“Router ID” on page 468
“Authentication” on page 469
Configurable Parameters
In ENOS, OSPF parameters can be configured through the Industry Standard Command Line Interfaces (ISCLI), Browser‐Based Interface (BBI), or through SNMP. For more information, see Chapter 1, “Switch Administration.”
The ISCLI supports the following parameters: interface output cost, interface priority, dead and hello intervals, retransmission interval, and interface transmit delay.
In addition to the preceding parameters, you can specify the following:
© Copyright Lenovo 2016

Shortest Path First (SPF) interval—Time interval between successive calculations of the shortest path tree using the Dijkstra’s algorithm.

Stub area metric—A stub area can be configured to send a numeric metric value such that all routes received via that stub area carry the configured metric to potentially influence routing decisions.

Default routes—Default routes with weight metrics can be manually injected into transit areas. This helps establish a preferred route when multiple routing devices exist between two areas. It also helps route traffic to external networks.

Passive—When enabled, the interface sends LSAs to upstream devices, but does not otherwise participate in OSPF protocol exchanges.

Point‐to‐Point—For LANs that have only two OSPF routing agents (the G8052 and one other device), this option allows the switch to significantly reduce the amount of routing information it must carry and manage.
Chapter 30: Open Shortest Path First
463
Defining Areas
If you are configuring multiple areas in your OSPF domain, one of the areas must be designated as area 0, known as the backbone. The backbone is the central OSPF area and is usually physically connected to all other areas. The areas inject routing information into the backbone which, in turn, disseminates the information into other areas.
Since the backbone connects the areas in your network, it must be a contiguous area. If the backbone is partitioned (possibly as a result of joining separate OSPF networks), parts of the AS will be unreachable, and you will need to configure virtual links to reconnect the partitioned areas (see “Virtual Links” on page 467).
Up to 20 OSPF areas can be connected to the G8052 with ENOS software. To configure an area, the OSPF number must be defined and then attached to a network interface on the switch. The full process is explained in the following sections.
An OSPF area is defined by assigning two pieces of information: an area index and an area ID. The commands to define and enable an OSPF area are as follows:
RS G8052(config)# router ospf
RS G8052(config­router­ospf)# area <area index> area­id <n.n.n.n>
RS G8052(config­router­ospf)# area <area index> enable
RS G8052(config­router­ospf)# exit
Note: The area option is an arbitrary index used only on the switch and does not represent the actual OSPF area number. The actual OSPF area number is defined in the area portion of the command as explained in the following sections.
Assigning the Area Index
The area <area index> option is actually just an arbitrary index (0‐19) used only by the G8052. This index number does not necessarily represent the OSPF area number, though for configuration simplicity, it ought to where possible.
For example, both of the following sets of commands define OSPF area 0 (the backbone) and area 1 because that information is held in the area ID portion of the command. However, the first set of commands is easier to maintain because the arbitrary area indexes agree with the area IDs:


464
Area index and area ID agree
area 0 area­id 0.0.0.0
(Use index 0 to set area 0 in ID octet format)
area 1 area­id 0.0.0.1
(Use index 1 to set area 1 in ID octet format)
Area index set to an arbitrary value
area 1 area­id 0.0.0.0
(Use index 1 to set area 0 in ID octet format)
area 2 area­id 0.0.0.1
(Use index 2 to set area 1 in ID octet format)
G8052 Application Guide for ENOS 8.4
Using the Area ID to Assign the OSPF Area Number
The OSPF area number is defined in the areaid <IP address> option. The octet format is used to be compatible with two different systems of notation used by other OSPF network vendors. There are two valid ways to designate an area ID:

Single Number
Most common OSPF vendors express the area ID number as a single number. For example, the Cisco IOS‐based router command “network 1.1.1.0 0.0.0.255 area 1” defines the area number simply as “area 1.” 
Multi‐octet (IP address): Placing the area number in the last octet (0.0.0.n)
Some OSPF vendors express the area ID number in multi‐octet format. For example, “area 0.0.0.2” represents OSPF area 2 and can be specified directly on the G8052 as “area­id 0.0.0.2”.
On the G8052, using the last octet in the area ID, “area 1” is equivalent to “area­id 0.0.0.1”.
Note: Although both types of area ID formats are supported, be sure that the area IDs are in the same format throughout an area.
Attaching an Area to a Network
Once an OSPF area has been defined, it must be associated with a network. To attach the area to a network, you must assign the OSPF area index to an IP interface that participates in the area. The format for the command is as follows:
RS G8052(config)# interface ip <interface number>
RS G8052(config­ip­if)# ip ospf area <area index>
RS G8052(config­ip­if)# exit
For example, the following commands could be used to configure IP interface 14 to use 10.10.10.1 on the 10.10.10.0/24 network, to define OSPF area 1, and to attach the area to the network:
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# router ospf
G8052(config­router­ospf)# area 1 area­id 0.0.0.1
G8052(config­router­ospf)# area 1 enable
G8052(config­router­ospf)# enable
G8052(config­router­ospf)# exit
G8052(config)# interface ip 14
G8052(config­ip­if)# ip address 10.10.10.1
G8052(config­ip­if)# ip netmask 255.255.255.0
G8052(config­ip­if)# enable
G8052(config­ip­if)# ip ospf area 1
G8052(config­ip­if)# ip ospf enable
Note: OSPFv2 supports IPv4 only. IPv6 is supported in OSPFv3 (see “OSPFv3 Implementation in Enterprise NOS” on page 482).
© Copyright Lenovo 2016
Chapter 30: Open Shortest Path First
465
Interface Cost
The OSPF link‐state algorithm (Dijkstra’s algorithm) places each routing device at the root of a tree and determines the cumulative cost required to reach each destination. You can manually enter the cost for the output route with the following command (Interface IP mode):
RS G8052(config­ip­if)# ip ospf cost <cost value (1‐65535)>
Electing the Designated Router and Backup
In any broadcast type subnet, a Designated Router (DR) is elected as the central contact for database exchanges among neighbors. On subnets with more the one device, a Backup Designated Router (BDR) is elected in case the DR fails.
DR and BDR elections are made through the hello process. The election can be influenced by assigning a priority value to the OSPF interfaces on the G8052. The command is as follows: RS G8052(config­ip­if)# ip ospf priority <priority value (0‐255)>
A priority value of 255 is the highest, and 1 is the lowest. A priority value of 0 specifies that the interface cannot be used as a DR or BDR. In case of a tie, the routing device with the highest router ID wins. Interfaces configured as passive do not participate in the DR or BDR election process:
RS G8052(config­ip­if)# ip ospf passive­interface
RS G8052(config­ip­if)# exit
Summarizing Routes
Route summarization condenses routing information. Without summarization, each routing device in an OSPF network would retain a route to every subnet in the network. With summarization, routing devices can reduce some sets of routes to a single advertisement, reducing both the load on the routing device and the perceived complexity of the network. The importance of route summarization increases with network size.
Summary routes can be defined for up to 16 IP address ranges using the following command: RS G8052(config)# router ospf
RS G8052(config­router­ospf)# area­range <range number> address <IP address> <mask>
where <range number> is a number 1 to 16, <IP address> is the base IP address for the range, and <mask> is the IP address mask for the range. For a detailed configuration example, see “Example 3: Summarizing Routes” on page 480.
466
G8052 Application Guide for ENOS 8.4
Default Routes
When an OSPF routing device encounters traffic for a destination address it does not recognize, it forwards that traffic along the default route. Typically, the default route leads upstream toward the backbone until it reaches the intended area or an external router.
Each G8052 acting as an ABR automatically inserts a default route into stub and NSSA attached areas. In simple OSPF stub areas or NSSAs with only one ABR leading upstream (see Area 1 in Figure 39), any traffic for IP address destinations outside the area is forwarded to the switch’s IP interface, and then into the connected transit area (usually the backbone). Since this is automatic, no further configuration is required for such areas.
Figure 39. Injecting Default Routes
If the switch is in a transit area and has a configured default gateway, it can inject a default route into rest of the OSPF domain. Use the following command to configure the switch to inject OSPF default routes (Router OSPF mode): RS G8052(config­router­ospf)# default­information <metric value> <metric type (1 or 2)>
In this command, <metric value> sets the priority for choosing this switch for default route. The value none sets no default and 1 sets the highest priority for default route. Metric type determines the method for influencing routing decisions for external routes.
When the switch is configured to inject a default route, an AS‐external LSA with link state ID 0.0.0.0 is propagated throughout the OSPF routing domain. This LSA is sent with the configured metric value and metric type.
The OSPF default route configuration can be removed with the command:
RS G8052(config­router­ospf)# no default­information
© Copyright Lenovo 2016
Chapter 30: Open Shortest Path First
467
Virtual Links
Usually, all areas in an OSPF AS are physically connected to the backbone. In some cases where this is not possible, you can use a virtual link. Virtual links are created to connect one area to the backbone through another non‐backbone area (see Figure 37 on page 459).
The area which contains a virtual link must be a transit area and have full routing information. Virtual links cannot be configured inside a stub area or NSSA. The area type must be defined as transit using the following command:
RS G8052(config­router­ospf)# area <area index> type transit
The virtual link must be configured on the routing devices at each endpoint of the virtual link, though they may traverse multiple routing devices. To configure a G8052 as one endpoint of a virtual link, use the following command:
RS G8052(config­router­ospf)# area­virtual­link <link number> neighbor­router <router ID>
where <link number> is a value between 1 and 3, <area index> is the OSPF area index of the transit area, and <router ID> is the router ID of the virtual neighbor, the routing device at the target endpoint. Another router ID is needed when configuring a virtual link in the other direction. To provide the G8052 with a router ID, see the following section Router ID.
For a detailed configuration example on Virtual Links, see “Example 2: Virtual Links” on page 476.
Router ID
Routing devices in OSPF areas are identified by a router ID. The router ID is expressed in IP address format. The IP address of the router ID is not required to be included in any IP interface range or in any OSPF area, and may even use the G8052 loopback interface.
The router ID can be configured in one of the following two ways:
Dynamically—OSPF protocol configures the lowest IP interface IP address as the router ID (loopback interface has priority over the IP interface). This is the default.  Statically—Use the following command to manually configure the router ID:

RS G8052(config­router­ospf)# ip router­id <IPv4 address>
If there is a loopback interface, its IP address is always preferred as the router ID, instead of an IP interface address. The ip router­id command is the preferred method to set the router ID and it is always used in preference to the other methods.
To modify the router ID from static to dynamic, set the router ID to 0.0.0.0 and re‐initialize the OSPF process.  To view the router ID, use the following command: 
RS G8052(config­router­ospf)# show ip ospf
468
G8052 Application Guide for ENOS 8.4
Authentication
OSPF protocol exchanges can be authenticated so that only trusted routing devices can participate. This ensures less processing on routing devices that are not listening to OSPF packets.
OSPF allows packet authentication and uses IP multicast when sending and receiving packets. Routers participate in routing domains based on pre‐defined passwords. ENOS supports simple password (type 1 plain text passwords) and MD5 cryptographic authentication. This type of authentication allows a password to be configured per interface.
We strongly recommend that you implement MD5 cryptographic authentication as a best practice.
Figure 40 shows authentication configured for area 0 with the password test. Simple authentication is also configured for the virtual link between area 2 and area 0. Area 1 is not configured for OSPF authentication.
Figure 40. OSPF Authentication Switch 2
Switch 1
Switch 3
Switch 5
key=blade
Switch 4
© Copyright Lenovo 2016
Chapter 30: Open Shortest Path First
469
Configuring Plain Text OSPF Passwords
To configure simple plain text OSPF passwords on the switches shown in Figure 40 use the following commands:
1. Enable OSPF authentication for Area 0 on switches 1, 2, and 3.
RS G8052(config­router­ospf)# area 0 authentication­type password
RS G8052(config­router­ospf)# exit
2. Configure a simple text password up to eight characters for each OSPF IP interface in Area 0 on switches 1, 2, and 3. RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip ospf key test
G8052(config­ip­if)# exit
G8052(config)# interface ip 2
G8052(config­ip­if)# ip ospf key test
G8052(config­ip­if)# exit
G8052(config)# interface ip 3
G8052(config­ip­if)# ip ospf key test
G8052(config­ip­if)# exit
3. Enable OSPF authentication for Area 2 on switch 4.
RS G8052(config)# router ospf
RS G8052(config­router­ospf)# area 2 authentication­type password
4. Configure a simple text password up to eight characters for the virtual link between Area 2 and Area 0 on switches 2 and 4.
RS G8052(config­router­ospf)# area­virtual­link 1 key blade
Configuring MD5 Authentication
Use the following commands to configure MD5 authentication on the switches shown in Figure 40:
1. Enable OSPF MD5 authentication for Area 0 on switches 1, 2, and 3.
RS G8052(config­router­ospf)# area 0 authentication­type md5
2. Configure MD5 key ID for Area 0 on switches 1, 2, and 3.
RS G8052(config­router­ospf)# message­digest­key 1 md5­key test
RS G8052(config­router­ospf)# exit
470
G8052 Application Guide for ENOS 8.4
3. Assign MD5 key ID to OSPF interfaces on switches 1, 2, and 3.
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip ospf message­digest­key 1
G8052(config­ip­if)# exit
G8052(config)# interface ip 2
G8052(config­ip­if)# ip ospf message­digest­key 1
G8052(config­ip­if)# exit
G8052(config)# interface ip 3
G8052(config­ip­if)# ip ospf message­digest­key 1
G8052(config­ip­if)# exit
4. Enable OSPF MD5 authentication for Area 2 on switch 4.
RS G8052(config)# router ospf
RS G8052(config­router­ospf)# area 1 authentication­type md5
5. Configure MD5 key for the virtual link between Area 2 and Area 0 on switches 2 and 4.
RS G8052(config­router­ospf)# message­digest­key 2 md5­key test
6. Assign MD5 key ID to OSPF virtual link on switches 2 and 4.
RS G8052(config­router­ospf)# area­virtual­link 1 message­digest­key 2
RS G8052(config­router­ospf)# exit
Host Routes for Load Balancing
ENOS implementation of OSPF includes host routes. Host routes are used for advertising network device IP addresses to external networks, accomplishing the following goals:

ABR Load Sharing
As a form of load balancing, host routes can be used for dividing OSPF traffic among multiple ABRs. To accomplish this, each switch provides identical services but advertises a host route for a different IP address to the external network. If each IP address serves a different and equal portion of the external world, incoming traffic from the upstream router must be split evenly among ABRs.

ABR Failover
Complementing ABR load sharing, identical host routes can be configured on each ABR. These host routes can be given different costs so that a different ABR is selected as the preferred route for each server and the others are available as backups for failover purposes.

Equal Cost Multipath (ECMP)
With equal cost multipath, a router potentially has several available next hops towards any given destination. ECMP allows separate routes to be calculated for each IP Type of Service. All paths of equal cost to a given destination are calcu‐
lated, and the next hops for all equal‐cost paths are inserted into the routing table.
© Copyright Lenovo 2016
Chapter 30: Open Shortest Path First
471
Loopback Interfaces in OSPF
A loopback interface is an IP interface which has an IP address, but is not associated with any particular physical port. The loopback interface is thus always available to the general network, regardless of which specific ports are in operation. Because loopback interfaces are always available on the switch, loopback interfaces may present an advantage when used as the router ID.
If dynamic router ID selection is used (see “Router ID” on page 468) loopback interfaces can be used to force router ID selection. If a loopback interface is configured, its IP address is automatically selected as the router ID, even if other IP interfaces have lower IP addresses. If more than one loopback interface is configured, the lowest loopback interface IP address is selected.
Loopback interfaces can be advertised into the OSPF domain by specifying an OSPF host route with the loopback interface IP address.
To enable OSPF on an existing loopback interface:
RS
RS
RS
RS
G8052(config)# interface loopback <1‐5>
G8052(config­ip­loopback)# ip ospf area <area ID>
G8052(config­ip­loopback)# ip ospf enable
G8052(config­ip­loopback)# exit
OSPF Features Not Supported in This Release
The following OSPF features are not supported in this release:
472

Summarizing external routes

Filtering OSPF routes

Using OSPF to forward multicast routes

Configuring OSPF on non‐broadcast multi‐access networks (such as frame relay, X.25, or ATM)
G8052 Application Guide for ENOS 8.4
OSPFv2 Configuration Examples
A summary of the basic steps for configuring OSPF on the G8052 is listed here. Detailed instructions for each of the steps is covered in the following sections:
1. Configure IP interfaces.
One IP interface is required for each desired network (range of IP addresses) being assigned to an OSPF area on the switch.
2. (Optional) Configure the router ID.
3. Enable OSPF on the switch.
4. Define the OSPF areas.
5. Configure OSPF interface parameters.
IP interfaces are used for attaching networks to the various areas.
6. (Optional) Configure route summarization between OSPF areas.
7. (Optional) Configure virtual links.
8. (Optional) Configure host routes.
© Copyright Lenovo 2016
Chapter 30: Open Shortest Path First
473
Example 1: Simple OSPF Domain
In this example, two OSPF areas are defined—one area is the backbone and the other is a stub area. A stub area does not allow advertisements of external routes, thus reducing the size of the database. Instead, a default summary route of IP address 0.0.0.0 is automatically inserted into the stub area. Any traffic for IP address destinations outside the stub area will be forwarded to the stub area’s IP interface, and then into the backbone.
Figure 41. A Simple OSPF Domain
Network
10.10.7.0/24
Network
10.10.12.0/24
Follow this procedure to configure OSPF support as shown in Figure 41:
1. Configure IP interfaces on each network that will be attached to OSPF areas.
In this example, two IP interfaces are needed:

Interface 1 for the backbone network on 10.10.7.0/24

Interface 2 for the stub area network on 10.10.12.0/24
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip address 10.10.7.1
G8052(config­ip­if)# ip netmask 255.255.255.0
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
G8052(config)# interface ip 2
G8052(config­ip­if)# ip address 10.10.12.1
G8052(config­ip­if)# ip netmask 255.255.255.0
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
Note: OSPFv2 supports IPv4 only. IPv6 is supported in OSPFv3 (see “OSPFv3 Implementation in Enterprise NOS” on page 482).
2. Enable OSPF. RS G8052(config)# router ospf
RS G8052(config­router­ospf)# enable
3. Define the backbone.
The backbone is always configured as a transit area using areaid 0.0.0.0.
RS G8052(config­router­ospf)# area 0 area­id 0.0.0.0
RS G8052(config­router­ospf)# area 0 type transit
RS G8052(config­router­ospf)# area 0 enable
474
G8052 Application Guide for ENOS 8.4
4. Define the stub area.
RS
RS
RS
RS
G8052(config­router­ospf)# area 1 area­id 0.0.0.1
G8052(config­router­ospf)# area 1 type stub
G8052(config­router­ospf)# area 1 enable
G8052(config­router­ospf)# exit
5. Attach the network interface to the backbone.
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip ospf area 0
G8052(config­ip­if)# ip ospf enable
G8052(config­ip­if)# exit
6. Attach the network interface to the stub area.
RS
RS
RS
RS
© Copyright Lenovo 2016
G8052(config)# interface ip 2
G8052(config­ip­if)# ip ospf area 1
G8052(config­ip­if)# ip ospf enable
G8052(config­ip­if)# exit
Chapter 30: Open Shortest Path First
475
Example 2: Virtual Links
In the example shown in Figure 42, area 2 is not physically connected to the backbone as is usually required. Instead, area 2 will be connected to the backbone via a virtual link through area 1. The virtual link must be configured at each endpoint.
Figure 42. Configuring a Virtual Link
Switch 1
Switch 2
Note: OSPFv2 supports IPv4 only. IPv6 is supported in OSPFv3 (see “OSPFv3 Implementation in Enterprise NOS” on page 482).
Configuring OSPF for a Virtual Link on Switch #1
1. Configure IP interfaces on each network that will be attached to the switch.
In this example, two IP interfaces are needed:

Interface 1 for the backbone network on 10.10.7.0/24

Interface 2 for the transit area network on 10.10.12.0/24
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip address 10.10.7.1
G8052(config­ip­if)# ip netmask 255.255.255.0
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
G8052(config)# interface ip 2
G8052(config­ip­if)# ip address 10.10.12.1
G8052(config­ip­if)# ip netmask 255.255.255.0
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
2. Configure the router ID.
A router ID is required when configuring virtual links. Later, when configuring the other end of the virtual link on Switch 2, the router ID specified here will be used as the target virtual neighbor (nbr) address.
RS G8052(config)# ip router­id 10.10.10.1 3. Enable OSPF.
RS G8052(config)# router ospf
RS G8052(config­router­ospf)# enable
476
G8052 Application Guide for ENOS 8.4
4. Define the backbone.
RS G8052(config­router­ospf)# area 0 area­id 0.0.0.0
RS G8052(config­router­ospf)# area 0 type transit
RS G8052(config­router­ospf)# area 0 enable
5. Define the transit area.
The area that contains the virtual link must be configured as a transit area.
RS
RS
RS
RS
G8052(config­router­ospf)# area 1 area­id 0.0.0.1
G8052(config­router­ospf)# area 1 type transit
G8052(config­router­ospf)# area 1 enable
G8052(config­router­ospf)# exit
6. Attach the network interface to the backbone.
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip ospf area 0
G8052(config­ip­if)# ip ospf enable
G8052(config­ip­if)# exit
7. Attach the network interface to the transit area.
RS
RS
RS
RS
G8052(config)# interface ip 2
G8052(config­ip­if)# ip ospf area 1
G8052(config­ip­if)# ip ospf enable
G8052(config­ip­if)# exit
8. Configure the virtual link.
The nbr router ID configured in this step must be the same as the router ID that will be configured for Switch #2 in Step 2 on page 478.
RS G8052(config)# router ospf
RS G8052(config­router­ospf)# area­virtual­link 1 area 1
RS G8052(config­router­ospf)# area­virtual­link 1 neighbor­router 10.10.14.1
RS G8052(config­router­ospf)# area­virtual­link 1 enable
Configuring OSPF for a Virtual Link on Switch #2
1. Configure IP interfaces on each network that will be attached to OSPF areas.
In this example, two IP interfaces are needed:

© Copyright Lenovo 2016
Interface 1 for the transit area network on 10.10.12.0/24
Chapter 30: Open Shortest Path First
477

Interface 2 for the stub area network on 10.10.24.0/24
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip address 10.10.12.2
G8052(config­ip­if)# ip netmask 255.255.255.0
G8052(config­ip­if)# vlan 10
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
G8052(config)# interface ip 2
G8052(config­ip­if)# ip address 10.10.24.1
G8052(config­ip­if)# ip netmask 255.255.255.0
G8052(config­ip­if)# vlan 20
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
2. Configure the router ID.
A router ID is required when configuring virtual links. This router ID must be the same one specified as the target virtual neighbor (nbr) on switch 1 in Step 8 on page 477.
RS G8052(config)# ip router­id 10.10.14.1 3. Enable OSPF.
RS G8052(config)# router ospf
RS G8052(config­router­ospf)# enable
4. Define the backbone.
This version of ENOS requires that a backbone index be configured on the non‐backbone end of the virtual link as follows:
RS G8052(config­router­ospf)# area 0 area­id 0.0.0.0
RS G8052(config­router­ospf)# area 0 enable
5. Define the transit area.
RS G8052(config­router­ospf)# area 1 area­id 0.0.0.1
RS G8052(config­router­ospf)# area 1 type transit
RS G8052(config­router­ospf)# area 1 enable
6. Define the stub area.
RS
RS
RS
RS
G8052(config­router­ospf)# area 2 area­id 0.0.0.2
G8052(config­router­ospf)# area 2 type stub
G8052(config­router­ospf)# area 2 enable
G8052(config­router­ospf)# exit
7. Attach the network interface to the transmit area.
RS
RS
RS
RS
478
G8052(config)# interface ip 1
G8052(config­ip­if)# ip ospf area 1
G8052(config­ip­if)# ip ospf enable
G8052(config­ip­if)# exit
G8052 Application Guide for ENOS 8.4
8. Attach the network interface to the stub area.
RS
RS
RS
RS
G8052(config)# interface ip 2
G8052(config­ip­if)# ip ospf area 2
G8052(config­ip­if)# ip ospf enable
G8052(config­ip­if)# exit
9. Configure the virtual link.
The nbr router ID configured in this step must be the same as the router ID that was configured for switch #1 in Step 2 on page 476.
RS G8052(config)# router ospf
RS G8052(config­router­ospf)# area­virtual­link 1 area 1
RS G8052(config­router­ospf)# area­virtual­link 1 neighbor­router 10.10.10.1
RS G8052(config­router­ospf)# area­virtual­link 1 enable
Other Virtual Link Options
© Copyright Lenovo 2016

You can use redundant paths by configuring multiple virtual links.

Only the endpoints of the virtual link are configured. The virtual link path may traverse multiple routers in an area as long as there is a routable path between the endpoints.
Chapter 30: Open Shortest Path First
479
Example 3: Summarizing Routes
By default, ABRs advertise all the network addresses from one area into another area. Route summarization can be used for consolidating advertised addresses and reducing the perceived complexity of the network.
If network IP addresses in an area are assigned to a contiguous subnet range, you can configure the ABR to advertise a single summary route that includes all individual IP addresses within the area.
The following example shows one summary route from area 1 (stub area) injected into area 0 (the backbone). The summary route consists of all IP addresses from 36.128.192.0 through 36.128.254.255 except for the routes in the range 36.128.200.0 through 36.128.200.255.
Figure 43. Summarizing Routes Notes:

OSPFv2 supports IPv4 only. IPv6 is supported in OSPFv3 (see “OSPFv3 Implementation in Enterprise NOS” on page 482).

You can specify a range of addresses to prevent advertising by using the hide option. In this example, routes in the range 36.128.200.0 through 36.128.200.255 are kept private.
Use the following procedure to configure OSPF support as shown in Figure 43:
1. Configure IP interfaces for each network which will be attached to OSPF areas.
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip address 10.10.7.1
G8052(config­ip­if)# ip netmask 255.255.255.0
G8052(config­ip­if)# vlan 10
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
G8052(config)# interface ip 2
G8052(config­ip­if)# ip address 36.128.192.1
G8052(config­ip­if)# ip netmask 255.255.255.0
G8052(config­ip­if)# vlan 20
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
2. Enable OSPF.
RS G8052(config)# router ospf
RS G8052(config­router­ospf)# enable
480
G8052 Application Guide for ENOS 8.4
3. Define the backbone.
RS G8052(config­router­ospf)# area 0 area­id 0.0.0.0
RS G8052(config­router­ospf)# area 0 type transit
RS G8052(config­router­ospf)# area 0 enable
4. Define the stub area.
RS
RS
RS
RS
G8052(config­router­ospf)# area 1 area­id 0.0.0.1
G8052(config­router­ospf)# area 1 type stub
G8052(config­router­ospf)# area 1 enable
G8052(config­router­ospf)# exit
5. Attach the network interface to the backbone.
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip ospf area 0
G8052(config­ip­if)# ip ospf enable
G8052(config­ip­if)# exit
6. Attach the network interface to the stub area.
RS
RS
RS
RS
G8052(config)# interface ip 2
G8052(config­ip­if)# ip ospf area 1
G8052(config­ip­if)# ip ospf enable
G8052(config­ip­if)# exit
7. Configure route summarization by specifying the starting address and mask of the range of addresses to be summarized.
RS G8052(config)# router ospf
RS G8052(config­router­ospf)# area­range 1 address 36.128.192.0 255.255.192.0
RS G8052(config­router­ospf)# area­range 1 area 1
RS G8052(config­router­ospf)# area­range 1 enable
RS G8052(config­router­ospf)# exit
8. Use the hide command to prevent a range of addresses from advertising to the backbone.
RS G8052(config)# router ospf
RS G8052(config­router­ospf)# area­range 2 address 36.128.200.0 255.255.255.0
RS G8052(config­router­ospf)# area­range 2 area 1
RS G8052(config­router­ospf)# area­range 2 hide RS G8052(config­router­ospf)# exit
Verifying OSPF Configuration
Use the following commands to verify the OSPF configuration on your switch:
show ip ospf show ip ospf neighbor  show ip ospf database database­summary
 show ip ospf routes 

Refer to the Lenovo Enterprise Network Operating System Command Reference for information on the preceding commands.
© Copyright Lenovo 2016
Chapter 30: Open Shortest Path First
481
OSPFv3 Implementation in Enterprise NOS
OSPF version 3 is based on OSPF version 2, but has been modified to support IPv6 addressing. In most other ways, OSPFv3 is similar to OSPFv2: They both have the same packet types and interfaces, and both use the same mechanisms for neighbor discovery, adjacency formation, LSA flooding, aging, and so on. The administrator must be familiar with the OSPFv2 concepts covered in the preceding sections of this chapter before implementing the OSPFv3 differences as described in the following sections.
Although OSPFv2 and OSPFv3 are very similar, they represent independent features on the G8052. They are configured separately, and both can run in parallel on the switch with no relation to one another, serving different IPv6 and IPv4 traffic, respectively.
The Enterprise NOS implementation conforms to the OSPF version 3 authentication/confidentiality specifications in RFC 4552.
OSPFv3 Differences from OSPFv2
Note: When OSPFv3 is enabled, the OSPF backbone area (0.0.0.0) is created by default and is always active.
OSPFv3 Requires IPv6 Interfaces
OSPFv3 is designed to support IPv6 addresses. This requires IPv6 interfaces to be configured on the switch and assigned to OSPF areas, in much the same way IPv4 interfaces are assigned to areas in OSPFv2. This is the primary configuration difference between OSPFv3 and OSPFv2.
See Chapter 24, “Internet Protocol Version 6,” for configuring IPv6 interfaces.
OSPFv3 Uses Independent Command Paths
Though OSPFv3 and OSPFv2 are very similar, they are configured independently. OSPFv3 command paths are located as follows:
RS G8052(config)# ipv6 router ospf
RS G8052(config­router­ospf3)# ?
(OSPFv3 router config mode)
RS G8052(config)# interface ip <Interface number>(Configure OSPFv3)
482
RS G8052(config­ip­if)# ipv6 ospf ?
(OSPFv3 interface config)
RS G8052# show ipv6 ospf ?
(Show OSPFv3 information)
G8052 Application Guide for ENOS 8.4
OSPFv3 Identifies Neighbors by Router ID
Where OSPFv2 uses a mix of IPv4 interface addresses and Router IDs to identify neighbors, depending on their type, OSPFv3 configuration consistently uses a Router ID to identify all neighbors.
Although Router IDs are written in dotted decimal notation, and may even be based on IPv4 addresses from an original OSPFv2 network configuration, it is important to realize that Router IDs are not IP addresses in OSPFv3, and can be assigned independently of IP address space. However, maintaining Router IDs consistent with any legacy OSPFv2 IPv4 addressing allows for easier implementation of both protocols.
Other Internal Improvements
OSPFv3 has numerous improvements that increase the protocol efficiency in addition to supporting IPv6 addressing. These improvements change some of the behaviors in the OSPFv3 network and may affect topology consideration, but have little direct impact on configuration. For example:

Addressing fields have been removed from Router and Network LSAs.

Flexible treatment of unknown LSA types to make integration of OSPFv3 easier.

Interface network type can be specified using the command: RS G8052(config­ip­if)# ipv6 ospf network {broadcast|non­broadcast|point­to­multipoint|point­to­point}

For an interface network type that is not broadcast or NBMA, link LSA suppression can be enabled so link LSA is not originated for the interface. Use the command: RS G8052(config­ip­if)# ipv6 ospf linklsasuppress
OSPFv3 Limitations
ENOS 8.4 does not currently support multiple interfaces of OSPFv3 on the same link.
OSPFv3 Configuration Example
The following example depicts the OSPFv3 equivalent configuration of “Example 3: Summarizing Routes” on page 480 for OSPFv2.
In this example, one summary route from area 1 (stub area) is injected into area 0 (the backbone). The summary route consists of all IP addresses from the 36::0/32 portion of the 36::0/56 network, except for the routes in the 36::0/8 range.
Figure 44. Summarizing Routes Backbone
Stub Area
Area 0
(0.0.0.0)
Area 1
(0.0.0.1)
IF 3
10::1
Summary Route
10::0/56
Network
© Copyright Lenovo 2016
IF 4
36::1
ABR
36::0/32
(- 36::0/8)
36::0/56
Network
Chapter 30: Open Shortest Path First
483
Note: You can specify a range of addresses to prevent advertising by using the hide option. In this example, routes in the 36::0/8 range are kept private.
Use the following procedure to configure OSPFv3 support as shown in Figure 43:
1. Configure IPv6 interfaces for each link which will be attached to OSPFv3 areas.
RS G8052RS G8052(config)# interface ip 3
(config­ip­if)# ipv6 address 10:0:0:0:0:0:0:1
RS G8052(config­ip­if)# ipv6 prefixlen 56
RS G8052(config­ip­if)# vlan 10
RS G8052(config­ip­if)# enable
RS G8052(config­ip­if)# exit
RS G8052(config)# interface ip 4
RS G8052(config­ip­if)# ip address 36:0:0:0:0:0:1
RS G8052(config­ip­if)# ipv6 prefixlen 56
RS G8052(config­ip­if)# vlan 20
RS G8052(config­ip­if)# enable
RS G8052(config­ip­if)# exit
This is equivalent to configuring the IP address and netmask for IPv4 interfaces.
2. Enable OSPFv3.
RS G8052(config)# ipv6 router ospf
RS G8052(config­router­ospf3)# enable
This is equivalent to the OSPFv2 enable option in the router ospf command path.
3. Define the backbone.
RS G8052(config­router­ospf3)# area 0 area­id 0.0.0.0
RS G8052(config­router­ospf3)# area 0 type transit
RS G8052(config­router­ospf3)# area 0 enable
This is identical to OSPFv2 configuration.
4. Define the stub area.
RS
RS
RS
RS
G8052(config­router­ospf3)# area 1 area­id 0.0.0.1
G8052(config­router­ospf3)# area 1 type stub
G8052(config­router­ospf3)# area 1 enable
G8052(config­router­ospf3)# exit
This is identical to OSPFv2 configuration.
5. Attach the network interface to the backbone.
RS
RS
RS
RS
G8052(config)# interface ip 3
G8052(config­ip­if)# ipv6 ospf area 0
G8052(config­ip­if)# ipv6 ospf enable
G8052(config­ip­if)# exit
The ipv6 command path is used instead of the OSPFv2 ip command path 484
G8052 Application Guide for ENOS 8.4
6. Attach the network interface to the stub area.
RS
RS
RS
RS
G8052(config)# interface ip 4
G8052(config­ip­if)# ipv6 ospf area 1
G8052(config­ip­if)# ipv6 ospf enable
G8052(config­ip­if)# exit
The ipv6 command path is used instead of the OSPFv2 ip command path 7. Configure route summarization by specifying the starting address and prefix length of the range of addresses to be summarized.
RS
RS
RS
RS
G8052(config)# ipv6 router ospf
G8052(config­router­ospf3)# area­range 1 address 36:0:0:0:0:0:0:0 32
G8052(config­router­ospf3)# area­range 1 area 0
G8052(config­router­ospf3)# area­range 1 enable
This differs from OSPFv2 only in that the OSPFv3 command path is used, and the address and prefix are specified in IPv6 format.
8. Use the hide command to prevent a range of addresses from advertising to the backbone.
RS
RS
RS
RS
G8052(config­router­ospf)# area­range 2 address 36:0:0:0:0:0:0:0 8
G8052(config­router­ospf)# area­range 2 area 0
G8052(config­router­ospf)# area­range 2 hide G8052(config­router­ospf)# exit
This differs from OSPFv2 only in that the OSPFv3 command path is used, and the address and prefix are specified in IPv6 format.
Neighbor Configuration Example
When using NBMA or point to multipoint interfaces, you must manually configure neighbors. Following example includes the steps for neighbor configuration.
1. Configure IPv6 interface parameters: RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config# interface ip 10
G8052(config­ip­if)# ipv6 address 10:0:0:0:0:0:0:12 64
G8052(config­ip­if)# vlan 10
G8052(config­ip­if)# enable
G8052(config­ip­if)# ipv6 ospf area 0
G8052(config­ip­if)# ipv6 ospf retransmit­interval 5
G8052(config­ip­if)# ipv6 ospf transmit­delay 1
G8052(config­ip­if)# ipv6 ospf priority 1
G8052(config­ip­if)# ipv6 ospf hello­interval 10
G8052(config­ip­if)# ipv6 ospf dead­interval 40
G8052(config­ip­if)# ipv6 ospf network point­to­multipoint
G8052(config­ip­if)# ipv6 ospf poll­interval 120
G8052(config­ip­if)# ipv6 ospf enable
G8052(config­ip­if)# exit
2. Enable OSPFv3: RS G8052(config# ipv6 router ospf
RS G8052(config­router­ospf3)# router­id 12.12.12.12
RS G8052(config­router­ospf3)# enable
© Copyright Lenovo 2016
Chapter 30: Open Shortest Path First
485
3. Define the backbone.
RS
RS
RS
RS
RS
RS
RS
G8052(config­router­ospf3)# area 0 area­id 0.0.0.0
G8052(config­router­ospf3)# area 0 stability­interval 40
G8052(config­router­ospf3)# area 0 default­metric 1
G8052(config­router­ospf3)# area 0 default­metric type 1
G8052(config­router­ospf3)# area 0 translation­role candidate
G8052(config­router­ospf3)# area 0 type transit
G8052(config­router­ospf3)# area 0 enable
4. Configure neighbor entry: RS G8052(config­router­ospf3)# neighbor 1 address fe80:0:0:0:dceb:ff:fe00:9
RS G8052(config­router­ospf3)# neighbor 1 interface 10
RS G8052(config­router­ospf3)# neighbor 1 priority 1
RS G8052(config­router­ospf3)# neighbor 1 enable
486
G8052 Application Guide for ENOS 8.4
Chapter 31. Protocol Independent Multicast
Lenovo Enterprise Network Operating System supports Protocol Independent Multicast (PIM) in Sparse Mode (PIM‐SM) and Dense Mode (PIM‐DM).
Note: Enterprise NOS 8.4 does not support IPv6 for PIM.
The following sections discuss PIM support for the RackSwitch G8052:
© Copyright Lenovo 2016

“PIM Overview” on page 488

“Supported PIM Modes and Features” on page 489

“Basic PIM Settings” on page 490

“Additional Sparse Mode Settings” on page 493

“Using PIM with Other Features” on page 496

“PIM Configuration Examples” on page 497
487
PIM Overview
PIM is designed for efficiently routing multicast traffic across one or more IPv4 domains. This has benefits for application such as IP television, collaboration, education, and software delivery, where a single source must deliver content (a multicast) to a group of receivers that span both wide‐area and inter‐domain networks.
Instead of sending a separate copy of content to each receiver, a multicast derives efficiency by sending only a single copy of content toward its intended receivers. This single copy only becomes duplicated when it reaches the target domain that includes multiple receivers, or when it reaches a necessary bifurcation point leading to different receiver domains.
PIM is used by multicast source stations, client receivers, and intermediary routers and switches, to build and maintain efficient multicast routing trees. PIM is protocol independent; It collects routing information using the existing unicast routing functions underlying the IPv4 network, but does not rely on any particular unicast protocol. For PIM to function, a Layer 3 routing protocol (such as BGP, OSPF, RIP, or static routes) must first be configured on the switch.
PIM‐SM is a reverse‐path routing mechanism. Client receiver stations advertise their willingness to join a multicast group. The local routing and switching devices collect multicast routing information and forward the request toward the station that will provide the multicast content. When the join requests reach the sending station, the multicast data is sent toward the receivers, flowing in the opposite direction of the original join requests.
Some routing and switching devices perform special PIM‐SM functions. Within each receiver domain, one router is elected as the Designated Router (DR) for handling multicasts for the domain. DRs forward information to a similar device, the Rendezvous Point (RP), which holds the root tree for the particular multicast group.
Receiver join requests as well as sender multicast content initially converge at the RP, which generates and distributes multicast routing data for the DRs along the delivery path. As the multicast content flows, DRs use the routing tree information obtained from the RP to optimize the paths both to and from send and receive stations, bypassing the RP for the remainder of content transactions if a more efficient route is available.
DRs continue to share routing information with the RP, modifying the multicast routing tree when new receivers join, or pruning the tree when all the receivers in any particular domain are no longer part of the multicast group.
488
G8052 Application Guide for ENOS 8.4
Supported PIM Modes and Features
For each interface attached to a PIM network component, PIM can be configured to operate either in PIM Sparse Mode (PIM‐SM) or PIM Dense Mode (PIM‐DM).

PIM‐SM is used in networks where multicast senders and receivers comprise a relatively small (sparse) portion of the overall network. PIM‐SM uses a more complex process than PIM‐DM for collecting and optimizing multicast routes, but minimizes impact on other IP services and is more commonly used.

PIM‐DM is used where multicast devices are a relatively large (dense) portion of the network, with very frequent (or constant) multicast traffic. PIM‐DM requires less configuration on the switch than PIM‐SM, but uses broadcasts that can consume more bandwidth in establishing and optimizing routes.
The following PIM modes and features are not currently supported in ENOS 8.4:
© Copyright Lenovo 2016

Hybrid Sparse‐Dense Mode (PIM‐SM/DM). Sparse Mode and Dense Mode may be configured on separate IP interfaces on the switch, but are not currently supported simultaneously on the same IP interface.

PIM Source‐Specific Multicast (PIM‐SSM)

Anycast RP

PIM RP filters

Only configuration via the switch ISCLI is supported. PIM configuration is currently not available using the menu‐based CLI, the BBI, or via SNMP.
Chapter 31: Protocol Independent Multicast
489
Basic PIM Settings
To use PIM the following is required:

The PIM feature must be enabled globally on the switch.

PIM network components and PIM modes must be defined.

IP interfaces must be configured for each PIM component.

PIM neighbor filters may be defined (optional).

If PIM‐SM is used, define additional parameters:

Rendezvous Point

Designated Router preferences (optional)

Bootstrap Router preferences (optional)
Each of these tasks is covered in the following sections.
Note: In ENOS 8.4, PIM can be configured through the ISCLI only. PIM configuration and information are not available using the menu‐based CLI, the BBI, or via SNMP.
Globally Enabling or Disabling the PIM Feature
By default, PIM is disabled on the switch. PIM can be globally enabled or disabled using the following commands: RS G8052(config)# [no] ip pim enable
Defining a PIM Network Component
The G8052 can be attached to a maximum of two independent PIM network components. Each component represents a different PIM network, and can be defined for either PIM‐SM or PIM‐DM operation. Basic PIM component configuration is performed using the following commands: RS G8052(config)# ip pim component <1‐2>
RS G8052(config­ip­pim­comp)# mode {sparse|dense}
RS G8052(config­ip­pim­comp)# exit
The sparse option will place the component in Sparse Mode (PIM‐SM). The dense option will place the component in Dense Mode (PIM‐DM). By default, PIM component 1 is configured for Sparse Mode. PIM component 2 is unconfigured by default.
Note: A component using PIM‐SM must also be configured with a dynamic or static Rendezvous Point (see “Specifying the Rendezvous Point” on page 493). Defining an IP Interface for PIM Use
Each network attached to an IP interface on the switch may be assigned one of the available PIM components. The same PIM component can be assigned to multiple IP interfaces. The interfaces may belong to the same VLAN, and they may also belong to different VLANs as long as their member IP addresses do not overlap.
490
G8052 Application Guide for ENOS 8.4
To define an IP interface for use with PIM, first configured the interface with an IPv4 address and VLAN as follows: RS
RS
RS
RS
G8052(config)# interface ip <Interface number>
G8052(config­ip­if)# ip address <IPv4 address> <IPv4 mask>
G8052(config­ip­if)# vlan <VLAN number>
G8052(config­ip­if)# enable
Note: The PIM feature currently supports only one VLAN for each IP interface. Configurations where different interfaces on different VLANs share IP addresses are not supported.
Next, PIM must be enabled on the interface, and the PIM network component ID must be specified: RS G8052(config­ip­if)# ip pim enable
RS G8052(config­ip­if)# ip pim component­id <1‐2>
RS G8052(config­ip­if)# exit
By default, PIM component 1 is automatically assigned when PIM is enabled on the IP interface.
Note: While PIM is enabled on the interface, the interface VLAN cannot be changed. To change the VLAN, first disable PIM on the interface.
PIM Neighbor Filters
The G8052 accepts connection to up to 8 PIM interfaces. By default, the switch accepts all PIM neighbors attached to the PIM‐enabled interfaces, up to the maximum number. Once the maximum is reached, the switch will deny further PIM neighbors.
To ensure that only the appropriate PIM neighbors are accepted by the switch, the administrator can use PIM neighbor filters to specify which PIM neighbors may be accepted or denied on a per‐interface basis.
To turn PIM neighbor filtering on or off for a particular IP interface, use the following commands:
RS G8052(config)# interface ip <Interface number>
RS G8052(config­ip­if)# [no] ip pim neighbor­filter
When filtering is enabled, all PIM neighbor requests on the specified IP interface will be denied by default. To allow a specific PIM neighbor, use the following command:
RS G8052(config­ip­if)# ip pim neighbor­addr <neighbor IPv4 address> allow
To remove a PIM neighbor from the accepted list, use the following command.
RS G8052(config­ip­if)# ip pim neighbor­addr <neighbor IPv4 address> deny
RS G8052(config­ip­if)# exit
© Copyright Lenovo 2016
Chapter 31: Protocol Independent Multicast
491
You can view configured PIM neighbor filters globally or for a specific IP interface using the following commands:
RS G8052(config)# show ip pim neighbor­filters
RS G8052(config)# show ip pim interface <Interface number> neighbor­filters
492
G8052 Application Guide for ENOS 8.4
Additional Sparse Mode Settings
Specifying the Rendezvous Point
Using PIM‐SM, at least one PIM‐capable router must be a candidate for use as a Rendezvous Point (RP) for any given multicast group. If desired, the G8052 can act as an RP candidate. To assign a configured switch IP interface as a candidate, use the following procedure.
1. Select the PIM component that will represent the RP candidate:
RS G8052(config)# ip pim component <1‐2>
2. Configure the IPv4 address of the switch interface which will be advertised as a candidate RP for the specified multicast group:
RS G8052(config­ip­pim­comp)# rp­candidate rp­address <group address> <group address mask> <candidate IPv4 address>
The switch interface will participate in the election of the RP that occurs on the Bootstrap Router, or BSR (see “Specifying a Bootstrap Router” on page 494).
3. If using dynamic RP candidates, configure the amount of time that the elected interface will remain the RP for the group before a re‐election is performed:
RS G8052(config­ip­pim­comp)# rp­candidate holdtime <0‐255>
RS G8052(config­ip­pim­comp)# exit
Static RP
If RP no election is desired, the switch can provide a static RP. Use the following commands:
1. Enable static RP configuration. RS G8052(config)# ip pim static­rp enable
2. Select the PIM component that will represent the RP candidate:
RS G8052(config)# ip pim component <1‐2>
3. Configure the static IPv4 address. RS G8052(config­ip­pim­comp)# rp­static rp­address <group address> <group address mask> <static IPv4 address>
Influencing the Designated Router Selection
Using PIM‐SM, All PIM‐enabled IP interfaces are considered as potential Designate Routers (DR) for their domain. By default, the interface with the highest IP address on the domain is selected. However, if an interface is configured with a © Copyright Lenovo 2016
Chapter 31: Protocol Independent Multicast
493
DR priority value, it overrides the IP address selection process. If more than one interface on a domain is configured with a DR priority, the one with the highest number is selected.
Use the following commands to configure the DR priority value (Interface IP mode):
RS G8052(config)# interface ip <Interface number>
RS G8052(config­ip­if)# ip pim dr­priority <value (0‐4294967294)>
RS G8052(config­ip­if)# exit
Note: A value of 0 (zero) specifies that the G8052 will not act as the DR. This setting requires the G8052 to be connected to a peer that has a DR priority setting of 1 or higher to ensure that a DR will be present in the network.
Specifying a Bootstrap Router
Using PIM‐SM, a Bootstrap Router (BSR) is a PIM‐capable router that hosts the election of the RP from available candidate routers. For each PIM‐enabled IP interface, the administrator can set the preference level for which the local interface becomes the BSR:
RS G8052(config)# interface ip <Interface number>
RS G8052(config­ip­if)# ip pim cbsr­preference <0 to 255>
RS G8052(config­ip­if)# exit
A value of 255 highly prefers the local interface as a BSR. A value of ‐1 indicates that the PIM CBSR preference is not configured on the switch.
Configuring a Loopback Interface
Loopback interfaces can be used in PIM Sparse Mode for Rendezvous Points (RPs) and Bootstrap Routers (BSRs). For example:

As a static RP
interface loopback 1
ip address 55.55.1.1 255.255.255.0
enable
exit
ip pim static­rp enable
ip pim component 1
rp­static rp­address 224.0.0.0 240.0.0.0 55.55.1.1
interface loopback 1
ip pim enable
exit
494
G8052 Application Guide for ENOS 8.4

As a candidate RP
interface loopback 1
ip address 55.55.1.1 255.255.255.0
enable
exit
ip pim component 1
rp­candidate holdtime 60
rp­candidate rp­address 224.0.0.0 240.0.0.0 55.55.1.1
interface loopback 1
ip pim enable
exit

As a BSR
interface loopback 1
ip address 55.55.1.1 255.255.255.0
enable
exit
interface loopback 1
ip pim enable
ip pim cbsr­preference 2
exit
© Copyright Lenovo 2016
Chapter 31: Protocol Independent Multicast
495
Using PIM with Other Features
PIM with ACLs or VMAPs
If using ACLs or VMAPs, be sure to permit traffic for local hosts and routers.
PIM with IGMP
If using IGMP (see Chapter 27, “Internet Group Management Protocol”):

IGMP static joins can be configured with a PIM‐SM or PIM‐DM multicast group IPv4 address. Using the ISCLI:
RS G8052(config)# ip mroute <multicast group IPv4 address> <VLAN> <port>
496

IGMP Querier is disabled by default. If IGMP Querier is needed with PIM, be sure to enable the IGMP Query feature globally, as well as on each VLAN where it is needed.

If the switch is connected to multicast receivers and/or hosts, be sure to enable IGMP snooping globally, as well as on each VLAN where PIM receivers are attached.
G8052 Application Guide for ENOS 8.4
PIM Configuration Examples
The following are examples of configuring Protocol Independent Multicast with various options.
Example 1: PIM-SM with Dynamic RP
This example configures PIM Sparse Mode for one IP interface, with the switch acting as a candidate for dynamic Rendezvous Point (RP) selection.
1. Globally enable the PIM feature:
RS G8052(config)# ip pim enable
2. Configure a PIM network component with dynamic RP settings, and set it for PIM Sparse Mode:
RS G8052(config)# ip pim component 1
RS G8052(config­ip­pim­comp)# mode sparse
RS G8052(config­ip­pim­comp)# rp­candidate rp­address 225.1.0.0 255.255.0.0 10.10.1.1
RS G8052(config­ip­pim­comp)# rp­candidate holdtime <0‐255>
RS G8052(config­ip­pim­comp)# exit
Where 225.1.0.0 is the multicast group base IP address, 255.255.0.0 is the multicast group address mask, and 10.10.1.1 is the switch RP candidate address.
Note: Because, Sparse Mode is set by default for PIM component 1, the mode command is needed only if the mode has been previously changed.
3. Define an IP interface for use with PIM:
RS
RS
RS
RS
G8052(config)# interface ip 111
G8052(config­ip­if)# ip address 10.10.1.1 255.255.255.255
G8052(config­ip­if)# vlan 11
G8052(config­ip­if)# enable
The IP interface represents the PIM network being connected to the switch. The IPv4 addresses in the defined range must not be included in another IP interface on the switch under a different VLAN.
4. Enable PIM on the IP interface and assign the PIM component:
RS G8052(config­ip­if)# ip pim enable
RS G8052(config­ip­if)# ip pim component­id 1
Note: Because, PIM component 1 is assigned to the interface by default, the component­id command is needed only if the setting has been previously changed.
5. Set the Bootstrap Router (BSR) preference:
RS G8052(config­ip­if)# ip pim cbsr­preference 135
RS G8052(config­ip­if)# exit
© Copyright Lenovo 2016
Chapter 31: Protocol Independent Multicast
497
Example 2: PIM-SM with Static RP
The following commands can be used to modify the prior example configuration to use a static RP:
RS G8052(config)# ip pim static­rp enable
RS G8052(config)# ip pim component 1
RS G8052(config­ip­pim­comp)# rp­static rp­address 225.1.0.0 255.255.0.0 10.10.1.1
RS G8052(config­ip­pim­comp)# exit
Where 225.1.0.0 255.255.0.0 is the multicast group base address and mask, and 10.10.1.1 is the static RP address.
Note: The same static RP address must be configured for all switches in the group.
Example 3: PIM-DM
This example configures PIM Dense Mode (PIM‐DM) on one IP interface. PIM‐DM can be configured independently, or it can be combined with the prior PIM‐SM examples (which are configured on a different PIM component) as shown in Figure 45.
Figure 45. Network with both PIM‐DM and PIM‐SM Components
PIM-SM
PIM-DM
Multicast
225.1.0.0/16
Multicast
239.1.0.0/16
PIM Enabled
Switch
IP Interface 11
IP Interface 22
IP 10.10.1.1
VLAN 101
Component 1
IP 10.10.2.1
VLAN 102
Component 2
Media
Servers
498
G8052 Application Guide for ENOS 8.4
1. Configure the PIM‐SM component as shown in the prior examples, or if using PIM‐DM independently, enable the PIM feature.
RS G8052(config)# ip pim enable
2. Configure a PIM component and set the PIM mode:
RS G8052(config)# ip pim component 2
RS G8052(config­ip­pim­comp)# mode dense
RS G8052(config­ip­pim­comp)# exit
3. Define an IP interface for use with PIM:
RS
RS
RS
RS
G8052(config)# interface ip 22
G8052(config­ip­if)# ip address 10.10.2.1 255.255.255.255
G8052(config­ip­if)# vlan 102
G8052(config­ip­if)# enable
4. Enable PIM on the IP interface and assign the PIM component:
RS G8052(config­ip­if)# ip pim enable
RS G8052(config­ip­if)# ip pim component­id 2
RS G8052(config­ip­if)# exit
5. (Optional) Configure PIM border router if the IPMC traffic is flowing between PIM domains: RS
RS
RS
RS
G8052(config)# ip pim pmbr enable
G8052(config)# interface ip 22
G8052(config­ip­if)# ip pim border­bit
G8052(config­ip­if)# exit
Note: For PIM Dense Mode, the DR, RP, and BSR settings do not apply.
© Copyright Lenovo 2016
Chapter 31: Protocol Independent Multicast
499
500
G8052 Application Guide for ENOS 8.4
Part 6: High Availability
Fundamentals
Internet traffic consists of myriad services and applications which use the Internet Protocol (IP) for data delivery. However, IP is not optimized for all the various applications. High Availability goes beyond IP and makes intelligent switching decisions to provide redundant network configurations.
© Copyright Lenovo 2016
501
502
G8052 Application Guide for ENOS 8.4
Chapter 32. Basic Redundancy
Lenovo Enterprise Network Operating System 8.4 includes various features for providing basic link or device redundancy:
© Copyright Lenovo 2016

“Aggregating for Link Redundancy” on page 504

“Virtual Link Aggregation” on page 504

“Hot Links” on page 505
503
Aggregating for Link Redundancy
Multiple switch ports can be combined together to form robust, high‐bandwidth LAGs to other devices. Since LAGs are comprised of multiple physical links, the LAG is inherently fault tolerant. As long as one connection between the switches is available, the LAG remains active.
In Figure 46, four ports are aggregated together between the switch and the enterprise routing device. Connectivity is maintained as long as one of the links remain active. The links to the server are also aggregated, allowing the secondary NIC to take over in the event that the primary NIC link fails.
Figure 46. Aggregating Ports for Link Redundancy
Enterprise
Routing Switch
Server
NIC 1
Internet
NIC 2
LAG
LAG
For more information on aggregation, see Chapter 10, “Ports and Link Aggregation.”
Virtual Link Aggregation
Using the VLAG feature, switches can be paired as VLAG peers. The peer switches appear to the connecting device as a single virtual entity for the purpose of establishing a multi‐port LAG. The VLAG‐capable switches synchronize their logical view of the access layer port structure and internally prevent implicit loops. The VLAG topology also responds more quickly to link failure and does not result in unnecessary MAC flooding.
VLAGs are useful in multi‐layer environments for both uplink and downlink redundancy to any regular LAG‐capable device. They can also be used in for active‐active VRRP connections.
For more information on VLAGs, see Chapter 12, “Virtual Link Aggregation Groups.”
504
G8052 Application Guide for ENOS 8.4
Hot Links
Hot Links provides basic link redundancy with fast recovery.
Hot Links consists of up to 25 triggers. A trigger consists of a pair of layer 2 interfaces, each containing an individual port, LAG, or LACP adminkey. One interface is the Master, and the other is a Backup. While the Master interface is set to the active state and forwards traffic, the Backup interface is set to the standby state and blocks traffic until the Master interface fails. If the Master interface fails, the Backup interface is set to active and forwards traffic. Once the Master interface is restored, it regains its active state and forwards traffic. The Backup transitions to the standby state.
You may select a physical port, static LAG, or an LACP adminkey as a Hot Link interface.
Forward Delay
The Forward Delay timer allows Hot Links to monitor the Master and Backup interfaces for link stability before selecting one interface to transition to the active state. Before the transition occurs, the interface must maintain a stable link for the duration of the Forward Delay interval.
For example, if you set the Forward delay timer to 10 seconds, the switch will select an interface to become active only if a link remained stable for the duration of the Forward Delay period. If the link is unstable, the Forward Delay period starts again. Preemption
You can configure the Master interface to resume the active state whenever it becomes available. With Hot Links preemption enabled, the Master interface transitions to the active state immediately upon recovery. The Backup interface immediately transitions to the standby state. If Forward Delay is enabled, the transition occurs when an interface has maintained link stability for the duration of the Forward Delay period.
FDB Update
Use the FDB update option to notify other devices on the network about updates to the Forwarding Database (FDB). When you enable FDB update, the switch sends multicasts of addresses in the forwarding database (FDB) over the active interface, so that other devices on the network can learn the new path. The Hot Links FBD update option uses the station update rate to determine the rate at which to send FDB packets.
Configuration Guidelines
The following configuration guidelines apply to Hot links:

© Copyright Lenovo 2016
When Hot Links is turned on, STP must be disabled on the hotlink ports.
Chapter 32: Basic Redundancy
505

A port that is a member of the Master interface cannot be a member of the Backup interface. A port that is a member of one Hot Links trigger cannot be a member of another Hot Links trigger.

An individual port that is configured as a Hot Link interface cannot be a member of a LAG.
Configuring Hot Links
Spanning Tree Protocol must be disabled on Hot Links ports. For instance, if Hot Links ports 1 and 2 belong to STGs 1 and 23, use the following commands to disable the STGs:
RS G8052(config)# no span stp 1 enable
RS G8052(config)# no span stp 23 enable
Use the following commands to configure Hot Links. RS G8052(config)# [no] hotlinks bpdu (Enable or disable Hot Links BPDU flood)
RS G8052(config)# [no] hotlinks enable (Enable or disable Hot Links globally)
RS G8052(config)# [no] hotlinks fdb­update (Enable or disable Hot Links FDB update)
RS G8052(config)# hotlinks fdb­update­rate (Configure FDB update rate in packets per second)
RS G8052(config)# hotlinks trigger 1 enable (Enable Hot Links Trigger 1)
RS G8052(config)# hotlinks trigger 1 master port 1 (Add port to Master interface)
RS G8052(config)# hotlinks trigger 1 backup port 2 (Add port to Backup interface)
RS G8052(config)# hotlinks enable 506
G8052 Application Guide for ENOS 8.4
(Turn on Hot Links)
Chapter 33. Layer 2 Failover
The primary application for Layer 2 Failover is to support Network Adapter Teaming. With Network Adapter Teaming, all the NICs on each server share the same IP address, and are configured into a team. One NIC is the primary link, and the other is a standby link. For more details, refer to the documentation for your Ethernet adapter. Note: Only two links per server can be used for Layer 2 LAG Failover (one primary and one backup). Network Adapter Teaming allows only one backup NIC for each server blade.
© Copyright Lenovo 2016
507
Monitoring LAG Links
Layer 2 Failover can be enabled on any LAG in the G8052, including LACP LAGs. LAGs can be added to failover trigger groups. Then, if some specified number of monitor links fail, the switch disables all the control ports in the switch. When the control ports are disabled, it causes the NIC team on the affected servers to failover from the primary to the backup NIC. This process is called a failover event.
When the appropriate number of links in a monitor group return to service, the switch enables the control ports. This causes the NIC team on the affected servers to fail back to the primary switch (unless Auto‐Fallback is disabled on the NIC team). The backup switch processes traffic until the primary switch’s control links come up, which can take up to five seconds.
Figure 47 is a simple example of Layer 2 Failover. One G8052 is the primary, and the other is used as a backup. In this example, all ports on the primary switch belong to a single LAG, with Layer 2 Failover enabled, and Failover Limit set to 2. If two or fewer links in trigger 1 remain active, the switch temporarily disables all control ports. This action causes a failover event on Server 1 and Server 2.
Figure 47. Basic Layer 2 Failover
Enterprise
Routing Switches
Primary
Switch
Trigger 1
Server 1
NIC 1
NIC 2
Backup
Switch
Internet
Trigger 1
Server 2
NIC 1
NIC 2
Setting the Failover Limit
The failover limit lets you specify the minimum number of operational links required within each trigger before the trigger initiates a failover event. For example, if the limit is two, a failover event occurs when the number of operational links in the trigger is two or fewer. When you set the limit to zero, the switch triggers a failover event only when no links in the trigger are operational.
508
G8052 Application Guide for ENOS 8.4
Manually Monitoring Port Links
The Manual Monitor allows you to configure a set of ports and LAGs to monitor for link failures (a monitor list), and another set of ports and LAGs to disable when the trigger limit is reached (a control list). When the switch detects a link failure on the monitor list, it automatically disables the items in control list. When server ports are disabled, the corresponding server’s network adapter can detect the disabled link, and trigger a network‐adapter failover to another port or LAG on the switch, or another switch.
The switch automatically enables the control list items when the monitor list items return to service.
Monitor Port State
A monitor port is considered operational as long as the following conditions are true:
The port must be in the Link Up state.
If STP is enabled, the port must be in the Forwarding state.
 If the port is part of an LACP LAG, the port must be in the Aggregated state.


If any of these conditions is false, the monitor port is considered to have failed.
Control Port State
A control port is considered Operational if the monitor trigger is up. As long as the trigger is up, the port is considered operational from a teaming perspective, even if the port itself is actually in the Down state, Blocking state (if STP is enabled on the port), or Not Aggregated state (if part of an LACP LAG).
A control port is considered to have failed only if the monitor trigger is in the Down state.
To view the state of any port, use one of the following commands:
>> # show interface link
>> # show interface port <x> spanning­tree stp <x>
>> # show lacp information
© Copyright Lenovo 2016
(View port link status)
(View port STP status)
(View port LACP status)
Chapter 33: Layer 2 Failover
509
L2 Failover with Other Features
L2 Failover works together with Link Aggregation Control Protocol (LACP) and with Spanning Tree Protocol (STP), as described in the next sections.
LACP
Link Aggregation Control Protocol allows the switch to form dynamic LAGs. You can use the admin key to add up to 52 LACP LAGs to a failover trigger using manual monitoring. When you add an admin key to a trigger, any LACP LAG with that admin key becomes a member of the trigger.
Spanning Tree Protocol
If Spanning Tree Protocol (STP) is enabled on the ports in a failover trigger, the switch monitors the port STP state rather than the link state. A port failure results when STP is not in a Forwarding state (such as Learning, Discarding, or No Link) in all the Spanning Tree Groups (STGs) to which the port belongs. The switch automatically disables the appropriate control ports.
When the switch determines that ports in the trigger are in STP Forwarding state in any one of the STGs it belongs to, then it automatically enables the appropriate control ports. The switch fails back to normal operation.
For example, if a monitor port is a member of STG1, STG2, and STG3, a failover will be triggered only if the port is not in a forwarding state in all the three STGs. When the port state in any of the three STGs changes to forwarding, then the control port is enabled and normal switch operation is resumed.
510
G8052 Application Guide for ENOS 8.4
Configuration Guidelines
This section provides important information about configuring Layer 2 Failover.

Any specific failover trigger can monitor ports only, static LAGs only, or LACP LAGs only. The different types cannot be combined in the same trigger.

A maximum of 52 LACP keys can be added per trigger.

Management ports cannot be monitored.

Control ports for different triggers must not overlap. Monitor ports may overlap.
Configuring Layer 2 Failover
Use the following procedure to configure a Layer 2 Failover Manual Monitor. 1. Specify the links to monitor. >> # failover trigger 1 mmon monitor member 1­5
2. Specify the links to disable when the failover limit is reached. >> # failover trigger 1 mmon control member 6­10
3. Configure general Failover parameters.
>> # failover enable
>> # failover trigger 1 enable
>> # failover trigger 1 limit 2
© Copyright Lenovo 2016
Chapter 33: Layer 2 Failover
511
512
G8052 Application Guide for ENOS 8.4
Chapter 34. Virtual Router Redundancy Protocol
The Lenovo RackSwitch G8052 (G8052) supports IPv4 high‐availability network topologies through an enhanced implementation of the Virtual Router Redundancy Protocol (VRRP).
Note: Lenovo Enterprise Network Operating System 8.4 does not support IPv6 for VRRP.
The following topics are discussed in this chapter:
© Copyright Lenovo 2016

“VRRP Overview” on page 514. This section discusses VRRP operation and Enterprise NOS redundancy configurations.

“Failover Methods” on page 517. This section describes the three modes of high availability.

“Enterprise NOS Extensions to VRRP” on page 518. This section describes VRRP enhancements implemented in ENOS.

“Virtual Router Deployment Considerations” on page 519. This section describes issues to consider when deploying virtual routers.

“High Availability Configurations” on page 520. This section discusses the more useful and easily deployed redundant configurations.
513
VRRP Overview
In a high‐availability network topology, no device can create a single point‐of‐failure for the network or force a single point‐of‐failure to any other part of the network. This means that your network will remain in service despite the failure of any single device. To achieve this usually requires redundancy for all vital network components.
VRRP enables redundant router configurations within a LAN, providing alternate router paths for a host to eliminate single points‐of‐failure within a network. Each participating VRRP‐capable routing device is configured with the same virtual router IPv4 address and ID number. One of the virtual routers is elected as the master, based on a number of priority criteria, and assumes control of the shared virtual router IPv4 address. If the master fails, one of the backup virtual routers will take control of the virtual router IPv4 address and actively process traffic addressed to it.
With VRRP, Virtual Interface Routers (VIR) allow two VRRP routers to share an IP interface across the routers. VIRs provide a single Destination IPv4 (DIP) address for upstream routers to reach various servers, and provide a virtual default Gateway for the servers.
VRRP Components
Each physical router running VRRP is known as a VRRP router.
Virtual Router
Two or more VRRP routers can be configured to form a virtual router (RFC 2338). Each VRRP router may participate in one or more virtual routers. Each virtual router consists of a user‐configured virtual router identifier (VRID) and an IPv4 address.
Virtual Router MAC Address
The VRID is used to build the virtual router MAC Address. The five highest‐order octets of the virtual router MAC Address are the standard MAC prefix (00‐00‐5E‐00‐01) defined in RFC 2338. The VRID is used to form the lowest‐order octet.
Owners and Renters
Only one of the VRRP routers in a virtual router may be configured as the IPv4 address owner. This router has the virtual router’s IPv4 address as its real interface address. This router responds to packets addressed to the virtual router’s IPv4 address for ICMP pings, TCP connections, and so on.
There is no requirement for any VRRP router to be the IPv4 address owner. Most VRRP installations choose not to implement an IPv4 address owner. For the purposes of this chapter, VRRP routers that are not the IPv4 address owner are called renters.
514
G8052 Application Guide for ENOS 8.4
Master and Backup Virtual Router
Within each virtual router, one VRRP router is selected to be the virtual router master. See “Selecting the Master VRRP Router” on page 516 for an explanation of the selection process.
Note: If the IPv4 address owner is available, it will always become the virtual router master.
The virtual router master forwards packets sent to the virtual router. It also responds to Address Resolution Protocol (ARP) requests sent to the virtual routerʹs IPv4 address. Finally, the virtual router master sends out periodic advertisements to let other VRRP routers know it is alive and its priority.
Within a virtual router, the VRRP routers not selected to be the master are known as virtual router backups. If the virtual router master fails, one of the virtual router backups becomes the master and assumes its responsibilities.
Virtual Interface Router
At Layer 3, a Virtual Interface Router (VIR) allows two VRRP routers to share an IP interface across the routers. VIRs provide a single Destination IPv4 (DIP) address for upstream routers to reach various destination networks, and provide a virtual default Gateway.
Note: Every VIR must be assigned to an IP interface, and every IP interface must be assigned to a VLAN. If no port in a VLAN has link up, the IP interface of that VLAN is down, and if the IP interface of a VIR is down, that VIR goes into INIT state.
VRRP Operation
Only the virtual router master responds to ARP requests. Therefore, the upstream routers only forward packets destined to the master. The master also responds to ICMP ping requests. The backup does not forward any traffic, nor does it respond to ARP requests.
If the master is not available, the backup becomes the master and takes over responsibility for packet forwarding and responding to ARP requests.
© Copyright Lenovo 2016
Chapter 34: Virtual Router Redundancy Protocol
515
Selecting the Master VRRP Router
Each VRRP router is configured with a priority between 1–254. A bidding process determines which VRRP router is or becomes the master—the VRRP router with the highest priority.
The master periodically sends advertisements to an IPv4 multicast address. As long as the backups receive these advertisements, they remain in the backup state. If a backup does not receive an advertisement for three advertisement intervals, it initiates a bidding process to determine which VRRP router has the highest priority and takes over as master. In addition to the three advertisement intervals, a manually set holdoff time can further delay the backups from assuming the master status.
If, at any time, a backup determines that it has higher priority than the current master does, it can preempt the master and become the master itself, unless configured not to do so. In preemption, the backup assumes the role of master and begins to send its own advertisements. The current master sees that the backup has higher priority and will stop functioning as the master.
A backup router can stop receiving advertisements for one of two reasons—the master can be down, or all communications links between the master and the backup can be down. If the master has failed, it is clearly desirable for the backup (or one of the backups, if there is more than one) to become the master.
Note: If the master is healthy but communication between the master and the backup has failed, there will then be two masters within the virtual router. To prevent this from happening, configure redundant links to be used between the switches that form a virtual router.
516
G8052 Application Guide for ENOS 8.4
Failover Methods
With service availability becoming a major concern on the Internet, service providers are increasingly deploying Internet traffic control devices, such as application switches, in redundant configurations. ENOS high availability configurations are based on VRRP. The ENOS implementation of VRRP includes proprietary extensions.
Active-Active Redundancy
In an active‐active configuration, shown in Figure 48, two switches provide redundancy for each other, with both active at the same time. Each switch processes traffic on a different subnet. When a failure occurs, the remaining switch can process traffic on all subnets.
For a configuration example, see “High Availability Configurations” on page 520.
Figure 48. Active‐Active Redundancy
Active (subnet A and C)
Switch 1
Servers
Internet
Enterprise
Routing Switch
Switch 2
Active (subnet B and D)
Virtual Router Group
The virtual router group ties all virtual routers on the switch together as a single entity. As members of a group, all virtual routers on the switch (and therefore the switch itself), are in either a master or standby state.
A VRRP group has the following characteristics:

When enabled, all virtual routers behave as one entity, and all group settings override any individual virtual router settings.

All individual virtual routers, once the VRRP group is enabled, assume the group’s tracking and priority.

When one member of a VRRP group fails, the priority of the group decreases, and the state of the entire switch changes from Master to Standby.

When VRRP group restrictions are enabled, advertisements for the group are sent and received only on VRRP group interface.
Each VRRP advertisement can include up to 128 addresses. All virtual routers are advertised within the same packet, conserving processing and buffering resources.
© Copyright Lenovo 2016
Chapter 34: Virtual Router Redundancy Protocol
517
Enterprise NOS Extensions to VRRP
This section describes VRRP enhancements that are implemented in ENOS.
ENOS supports a tracking function that dynamically modifies the priority of a VRRP router, based on its current state. The objective of tracking is to have, whenever possible, the master bidding processes for various virtual routers in a LAN converge on the same switch. Tracking ensures that the selected switch is the one that offers optimal network performance. For tracking to have any effect on virtual router operation, preemption must be enabled.
ENOS can track the attributes listed in Table 34 (Router VRRP mode):
Table 34. VRRP Tracking Parameters
Parameter
Description
Number of IP interfaces on the switch that are active (“up”)
Helps elect the virtual routers with the most available routes as the master. (An IP interface is considered active when there tracking­priority­increment is at least one active port on the same interfaces
VLAN.) This parameter influences the VRRP routerʹs priority in virtual interface routers. Helps elect the virtual routers with the most available ports as the master. This parameter influences the VRRP routerʹs tracking­priority­increment priority in virtual interface routers.
ports
Number of active ports on the same VLAN
Number of virtual routers in master Useful for ensuring that traffic for any mode on the switch
particular client/server pair is handled by the same switch, increasing routing tracking­priority­increment efficiency. This parameter influences the virtual­routers
VRRP routerʹs priority in virtual interface routers.
Each tracked parameter has a user‐configurable weight associated with it. As the count associated with each tracked item increases (or decreases), so does the VRRP routerʹs priority, subject to the weighting associated with each tracked item. If the priority level of a standby is greater than that of the current master, then the standby can assume the role of the master.
See “Configuring the Switch for Tracking” on page 519 for an example on how to configure the switch for tracking VRRP priority.
518
G8052 Application Guide for ENOS 8.4
Virtual Router Deployment Considerations
Allow for the following when setting up a virtual router.
Assigning VRRP Virtual Router ID
During the software upgrade process, VRRP virtual router IDs will be automatically assigned if failover is enabled on the switch. When configuring virtual routers at any point after upgrade, virtual router ID numbers must be assigned. The virtual router ID may be configured as any number between 1 and 255. Use the following command to configure the virtual router ID: RS G8052(config)# router vrrp
RS G8052(config­vrrp)# virtual­router 1 virtual­router­id <1‐255>
Configuring the Switch for Tracking
Tracking configuration largely depends on user preferences and network environment. Consider the configuration shown in Figure 48 on page 517. Assume the following behavior on the network:

Switch 1 is the master router upon initialization.

If switch 1 is the master and it has one fewer active servers than switch 2, then switch 1 remains the master.
This behavior is preferred because running one server down is less disruptive than bringing a new master online and severing all active connections in the process.

If switch 1 is the master and it has two or more active servers fewer than switch 2, then switch 2 becomes the master.

If switch 2 is the master, it remains the master even if servers are restored on switch 1 such that it has one fewer or an equal number of servers.

If switch 2 is the master and it has one active server fewer than switch 1, then switch 1 becomes the master.
You can implement this behavior by configuring the switch for tracking as follows:
1. Set the priority for switch 1 to 101.
2. Leave the priority for switch 2 at the default value of 100.
3. On both switches, enable tracking based on ports, interfacesor virtual routers. You can choose any combination of tracking parameters, based on your network configuration.
Note: There is no shortcut to setting tracking parameters. The goals must first be set and the outcomes of various configurations and scenarios analyzed to find settings that meet the goals.
© Copyright Lenovo 2016
Chapter 34: Virtual Router Redundancy Protocol
519
High Availability Configurations
The following are possible scenarios using VRRP HA.
VRRP High-Availability Using Multiple VIRs
Figure 49 shows an example configuration where two G8052s are used as VRRP routers in an active‐active configuration. In this configuration, both switches respond to packets.
Figure 49. Active‐Active Configuration using VRRP
L2 Switch
VIR 1: 192.168.1.200 (Master) Server 1
VIR 2: 192.168.2.200 (Backup)
1
2
Internet
NIC 1: 10.0.1.1/24
NIC 2: 10.0.2.1/24
Server 2
Switch 1
NIC 1: 10.0.1.2/24
NIC 2: 10.0.2.2/24
4
Server 3
4
Enterprise
Routing Switch
1
2
L2 Switch
Server 4
Switch 2
VIR 1: 192.168.1.200 (Backup)
VIR 2: 192.168.2.200 (Master)
NIC 1: 10.0.1.3/24
NIC 2: 10.0.2.3/24
NIC 1: 10.0.1.4/24
NIC 2: 10.0.2.4/24
Although this example shows only two switches, there is no limit on the number of switches used in a redundant configuration. It is possible to implement an active‐active configuration across all the VRRP‐capable switches in a LAN.
Each VRRP‐capable switch in an active‐active configuration is autonomous. Switches in a virtual router need not be identically configured.
In the scenario illustrated in Figure 49, traffic destined for IPv4 address 10.0.1.1 is forwarded through the Layer 2 switch at the top of the drawing, and ingresses G8052 1 on port 1. Return traffic uses default gateway 1 (192.168.1.1).
If the link between G8052 1 and the Layer 2 switch fails, G8052 2 becomes the Master because it has a higher priority. Traffic is forwarded to G8052 2, which forwards it to G8052 1 through port 4. Return traffic uses default gateway 2 (192.168.2.1), and is forwarded through the Layer 2 switch at the bottom of the drawing.
520
G8052 Application Guide for ENOS 8.4
To implement the active‐active example, perform the following switch configuration.
Task 1: Configure G8052 1
1. Configure client and server interfaces.
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip address 192.168.1.100 255.255.255.0
G8052(config­ip­if)# vlan 10
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
G8052(config)# interface ip 2
G8052(config­ip­if)# ip address 192.168.2.101 255.255.255.0
G8052(config­ip­if)# vlan 20
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
G8052(config)# interface ip 3
G8052(config­ip­if)# ip address 10.0.1.100 255.255.255.0
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
G8052(config)# interface ip 4
G8052(config­ip­if)# ip address 10.0.2.101 255.255.255.0
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
2. Configure the default gateways. Each default gateway points to a Layer 3 router.
RS
RS
RS
RS
G8052(config)# ip gateway 1 address 192.168.1.1
G8052(config)# ip gateway 1 enable
G8052(config)# ip gateway 2 address 192.168.2.1
G8052(config)# ip gateway 2 enable
3. Turn on VRRP and configure two Virtual Interface Routers.
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# router vrrp
G8052(config­vrrp)# enable
G8052(config­vrrp)# virtual­router 1 virtual­router­id 1
G8052(config­vrrp)# virtual­router 1 interface 1
G8052(config­vrrp)# virtual­router 1 address 192.168.1.200
G8052(config­vrrp)# virtual­router 1 enable
G8052(config­vrrp)# virtual­router 2 virtual­router­id 2
G8052(config­vrrp)# virtual­router 2 interface 2
G8052(config­vrrp)# virtual­router 2 address 192.168.2.200
G8052(config­vrrp)# virtual­router 2 enable
4. Enable tracking on ports. Set the priority of Virtual Router 1 to 101, so that it becomes the Master.
RS
RS
RS
RS
© Copyright Lenovo 2016
G8052(config­vrrp)# virtual­router 1 track ports
G8052(config­vrrp)# virtual­router 1 priority 101
G8052(config­vrrp)# virtual­router 2 track ports
G8052(config­vrrp)# exit
Chapter 34: Virtual Router Redundancy Protocol
521
5. Configure ports.
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 10
G8052(config­vlan)# exit
G8052(config)# interface port 1
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 10
G8052(config­if)# exit
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 20
G8052(config­vlan)# exit
G8052(config)# interface port 2
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 20
G8052(config­if)# exit
6. Turn off Spanning Tree Protocol globally.
RS G8052(config)# no spanning­tree stp 1
Task 2: Configure G8052 2
1. Configure client and server interfaces.
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# interface ip 1
G8052(config­ip­if)# ip address 192.168.1.101 255.255.255.0
G8052(config­ip­if)# vlan 10
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
G8052(config)# interface ip 2
G8052(config­ip­if)# ip address 192.168.2.100 255.255.255.0
G8052(config­ip­if)# vlan 20
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
G8052(config)# interface ip 3
G8052(config­ip­if)# ip address 10.0.1.101 255.255.255.0
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
G8052(config)# interface ip 4
G8052(config­ip­if)# ip address 10.0.2.100 255.255.255.0
G8052(config­ip­if)# enable
G8052(config­ip­if)# exit
2. Configure the default gateways. Each default gateway points to a Layer 3 router.
RS
RS
RS
RS
522
G8052(config)# ip gateway 1 address 192.168.2.1
G8052(config)# ip gateway 1 enable
G8052(config)# ip gateway 2 address 192.168.1.1
G8052(config)# ip gateway 2 enable
G8052 Application Guide for ENOS 8.4
3. Turn on VRRP and configure two Virtual Interface Routers.
RS
RS
RS
RS
RS
RS
RS
RS
RS
RS
G8052(config)# router vrrp
G8052(config­vrrp)# enable
G8052(config­vrrp)# virtual­router 1 virtual­router­id 1
G8052(config­vrrp)# virtual­router 1 interface 1
G8052(config­vrrp)# virtual­router 1 address 192.168.1.200
G8052(config­vrrp)# virtual­router 1 enable
G8052(config­vrrp)# virtual­router 2 virtual­router­id 2
G8052(config­vrrp)# virtual­router 2 interface 2 G8052(config­vrrp)# virtual­router 2 address 192.168.2.200
G8052(config­vrrp)# virtual­router 2 enable
4. Enable tracking on ports. Set the priority of Virtual Router 2 to 101, so that it becomes the Master.
RS
RS
RS
RS
G8052(config­vrrp)# virtual­router 1 track ports
G8052(config­vrrp)# virtual­router 2 track ports
G8052(config­vrrp)# virtual­router 2 priority 101
G8052(config­vrrp)# exit
5. Configure ports.
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 10
G8052(config­vlan)# exit
G8052(config)# interface port 1
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 10
G8052(config­if)# exit
RS
RS
RS
RS
RS
RS
G8052(config)# vlan 20
G8052(config­vlan)# exit
G8052(config)# interface port 2
G8052(config­if)# switchport mode trunk
G8052(config­if)# switchport trunk allowed vlan 20
G8052(config­if)# exit
6. Turn off Spanning Tree Protocol globally.
RS G8052(config)# no spanning­tree stp 1
© Copyright Lenovo 2016
Chapter 34: Virtual Router Redundancy Protocol
523
VRRP High-Availability Using VLAGs
VRRP can be used in conjunction with VLAGs and LACP‐capable servers and switches to provide seamless redundancy.
Figure 50. Active‐Active Configuration using VRRP and VLAGs
VRRP Master
Server 1
VLAG Peer 1
Layer 3
Router
VLAG 1
VIR: 10.0.1.100
1
10
10.0.1.1
11
2
Internet
4
5
4
5
VLAG 2
12
ISL
10.0.1.2
10
1
Server 2
11
12
VLAG 3
Server 3
2
Layer 3
Router
VRRP Backup
10.0.1.3
VLAG Peer 2
VIR: 10.0.1.100
Network 10.0.1.0/24
See “VLAGs with VRRP” on page 212 for a detailed configuration example.
524
G8052 Application Guide for ENOS 8.4
Part 7: Network
Management
© Copyright Lenovo 2016
525
526
G8052 Application Guide for ENOS 8.4
Chapter 35. Link Layer Discovery Protocol
The Lenovo Enterprise Network Operating System software support Link Layer Discovery Protocol (LLDP). This chapter discusses the use and configuration of LLDP on the switch:
© Copyright Lenovo 2016

“LLDP Overview” on page 528

“Enabling or Disabling LLDP” on page 529

“LLDP Transmit Features” on page 530

“LLDP Receive Features” on page 534

“LLDP Example Configuration” on page 538
527
LLDP Overview
Link Layer Discovery Protocol (LLDP) is an IEEE 802.1AB‐2005 standard for discovering and managing network devices. LLDP uses Layer 2 (the data link layer), and allows network management applications to extend their awareness of the network by discovering devices that are direct neighbors of already known devices.
With LLDP, the G8052 can advertise the presence of its ports, their major capabilities, and their current status to other LLDP stations in the same LAN. LLDP transmissions occur on ports at regular intervals or whenever there is a relevant change to their status. The switch can also receive LLDP information advertised from adjacent LLDP‐capable network devices.
In addition to discovery of network resources, and notification of network changes, LLDP can help administrators quickly recognize a variety of common network configuration problems, such as unintended VLAN exclusions or mis‐matched port aggregation membership.
The LLDP transmit function and receive function can be independently configured on a per‐port basis. The administrator can allow any given port to transmit only, receive only, or both transmit and receive LLDP information.
The LLDP information to be distributed by the G8052 ports, and that which has been collected from other LLDP stations, is stored in the switch’s Management Information Base (MIB). Network Management Systems (NMS) can use Simple Network Management Protocol (SNMP) to access this MIB information. LLDP‐related MIB information is read‐only.
Changes, either to the local switch LLDP information or to the remotely received LLDP information, are flagged within the MIB for convenient tracking by SNMP‐based management systems.
For LLDP to provide expected benefits, all network devices that support LLDP must be consistent in their LLDP configuration.
528
G8052 Application Guide for ENOS 8.4
Enabling or Disabling LLDP
Follow the instructions in this section to enable and disable LLDP.
Global LLDP Setting
By default, LLDP is enabled on the G8052. To turn LLDP on or off, use the following command:
RS G8052(config)# [no] lldp enable
(Turn LLDP on or off globally)
Transmit and Receive Control
The G8052 can also be configured to transmit or receive LLDP information on a port‐by‐port basis. By default, when LLDP is globally enabled on the switch, G8052 ports transmit and receive LLDP information (see the tx_rx option in the following example). To change the LLDP transmit and receive state, the following commands are available:
RS
RS
RS
RS
RS
RS
G8052(config)# interface port 1
G8052(config­if)# lldp admin­status tx_rx
G8052(config­if)# lldp admin­status tx_only
G8052(config­if)# lldp admin­status rx_only
G8052(config­if)# no lldp admin­status
G8052(config­if)# exit
(Select a switch port)
(Transmit and receive LLDP)
(Only transmit LLDP)
(Only receive LLDP)
(Do not participate in LLDP)
(Exit port mode)
To view the LLDP transmit and receive status, use the following commands:
RS G8052(config)# show lldp port
RS G8052(config)# show interface port <n> lldp
© Copyright Lenovo 2016
(status of all ports)
(status of selected port)
Chapter 35: Link Layer Discovery Protocol
529
LLDP Transmit Features
Numerous LLDP transmit options are available, including scheduled and minimum transmit interval, expiration on remote systems, SNMP trap notification, and the types of information permitted to be shared.
Scheduled Interval
The G8052 can be configured to transmit LLDP information to neighboring devices once each 5 to 32768 seconds. The scheduled interval is global; the same interval value applies to all LLDP transmit‐enabled ports. However, to help balance LLDP transmissions and keep them from being sent simultaneously on all ports, each port maintains its own interval clock, based on its own initialization or reset time. This allows switch‐wide LLDP transmissions to be spread out over time, though individual ports comply with the configured interval.
The global transmit interval can be configured using the following command:
RS G8052(config)# lldp refresh­interval <interval>
where interval is the number of seconds between LLDP transmissions. The range is 5 to 32768. The default is 30 seconds.
Minimum Interval
In addition to sending LLDP information at scheduled intervals, LLDP information is also sent when the G8052 detects relevant changes to its configuration or status (such as when ports are enabled or disabled). To prevent the G8052 from sending multiple LLDP packets in rapid succession when port status is in flux, a transmit delay timer can be configured.
The transmit delay timer represents the minimum time permitted between successive LLDP transmissions on a port. Any interval‐driven or change‐driven updates will be consolidated until the configured transmit delay expires.
The minimum transmit interval can be configured using the following command:
RS G8052(config)# lldp transmission­delay <interval>
where interval is the minimum number of seconds permitted between successive LLDP transmissions on any port. The range is 1 to one‐quarter of the scheduled transmit interval (lldp refresh­interval <value>), up to 8192. The default is 2 seconds.
530
G8052 Application Guide for ENOS 8.4
Time-to-Live for Transmitted Information
The transmitted LLDP information is held by remote systems for a limited time. A time‐to‐live parameter allows the switch to determine how long the transmitted data is held before it expires. The hold time is configured as a multiple of the configured transmission interval.
RS G8052(config)# lldp holdtime­multiplier <multiplier>
where multiplier is a value between 2 and 10. The default value is 4, meaning that remote systems will hold the port’s LLDP information for 4 x the 30‐second msgtxint value, or 120 seconds, before removing it from their MIB.
Trap Notifications
If SNMP is enabled on the G8052 (see “Using Simple Network Management Protocol” on page 39), each port can be configured to send SNMP trap notifications whenever LLDP transmissions are sent. By default, trap notification is disabled for each port. The trap notification state can be changed using the following commands (Interface Port mode):
RS G8052(config)# interface port 1
RS G8052(config­if)# [no] lldp trap­notification
RS G8052(config­if)# exit
In addition to sending LLDP information at scheduled intervals, LLDP information is also sent when the G8052 detects relevant changes to its configuration or status (such as when ports are enabled or disabled). To prevent the G8052 from sending multiple trap notifications in rapid succession when port status is in flux, a global trap delay timer can be configured.
The trap delay timer represents the minimum time permitted between successive trap notifications on any port. Any interval‐driven or change‐driven trap notices from the port will be consolidated until the configured trap delay expires.
The minimum trap notification interval can be configured using the following command:
RS G8052(config)# lldp trap­notification­interval <interval>
where interval is the minimum number of seconds permitted between successive LLDP transmissions on any port. The range is 1 to 3600. The default is 5 seconds.
If SNMP trap notification is enabled, the notification messages can also appear in the system log. This is enabled by default. To change whether the SNMP trap notifications for LLDP events appear in the system log, use the following command:
RS G8052(config)# [no] logging log lldp
© Copyright Lenovo 2016
Chapter 35: Link Layer Discovery Protocol
531
Changing the LLDP Transmit State
When the port is disabled, or when LLDP transmit is turned off for the port using the LLDP admin‐status command options (see “Transmit and Receive Control” on page 529), a final LLDP packet is transmitted with a time‐to‐live value of 0. Neighbors that receive this packet will remove the LLDP information associated with the G8052 port from their MIB.
In addition, if LLDP is fully disabled on a port and then later re‐enabled, the G8052 will temporarily delay resuming LLDP transmissions on the port to allow the port LLDP information to stabilize. The reinitialization delay interval can be globally configured for all ports using the following command:
RS G8052(config)# lldp reinit­delay <interval>
where interval is the number of seconds to wait before resuming LLDP transmissions. The range is between 1 and 10. The default is 2 seconds.
Types of Information Transmitted
When LLDP transmission is permitted on the port (see “Enabling or Disabling LLDP” on page 529), the port advertises the following required information in type/length/value (TLV) format:
Chassis ID
Port ID
 LLDP Time‐to‐Live


LLDP transmissions can also be configured to enable or disable inclusion of optional information, using the following command (Interface Port mode): RS G8052(config)# interface port 1
RS G8052(config­if)# [no] lldp tlv <type>
RS G8052(config­if)# exit
where type is an LLDP information option from Table 35:
Table 35. LLDP Optional Information Types
532
Type
Description
Default
portdesc
Port Description
Enabled
sysname
System Name
Enabled
sysdescr
System Description
Enabled
syscap
System Capabilities
Enabled
mgmtaddr
Management Address
Enabled
portvid
IEEE 802.1 Port VLAN ID
Disabled
portprot
IEEE 802.1 Port and Protocol VLAN ID
Disabled
vlanname
IEEE 802.1 VLAN Name
Disabled
G8052 Application Guide for ENOS 8.4
Table 35. LLDP Optional Information Types (continued)
© Copyright Lenovo 2016
Type
Description
Default
protid
IEEE 802.1 Protocol Identity
Disabled
macphy
IEEE 802.3 MAC/PHY Configuration/Status, including the auto‐negotiation, duplex, and speed status of the port.
Disabled
powermdi
IEEE 802.3 Power via MDI, indicating the Disabled
capabilities and status of devices that require or provide power over twisted‐pair copper links.
linkaggr
IEEE 802.3 Link Aggregation status for the port.
Disabled
framesz
IEEE 802.3 Maximum Frame Size for the port.
Disabled
all
Select all optional LLDP information for inclusion or exclusion.
Disabled
Chapter 35: Link Layer Discovery Protocol
533
LLDP Receive Features
LLDP on the G8052 has the following features. Types of Information Received
When the LLDP receive option is enabled on a port (see “Enabling or Disabling LLDP” on page 529), the port may receive the following information from LLDP‐capable remote systems:








Chassis Information
Port Information
LLDP Time‐to‐Live
Port Description
System Name
System Description
System Capabilities Supported/Enabled
Remote Management Address
The G8052 stores the collected LLDP information in the MIB. Each remote LLDP‐capable device is responsible for transmitting regular LLDP updates. If the received updates contain LLDP information changes (to port state, configuration, LLDP MIB structures, deletion), the switch will set a change flag within the MIB for convenient notification to SNMP‐based management systems.
Viewing Remote Device Information
LLDP information collected from neighboring systems can be viewed in numerous ways:
Using a centrally‐connected LLDP analysis server
 Using an SNMP agent to examine the G8052 MIB
 Using the G8052 Browser‐Based Interface (BBI)
 Using commands on the G8052

The following command displays remote LLDP information:
RS G8052(config)# show lldp remote­device [<index number>]
To view a summary of remote information, omit the Index number parameter. For example:
RS G8052(config)# show lldp remote­device
LLDP Remote Devices Information
Legend(possible values in DMAC column) :
NB ­ Nearest Bridge ­ 01­80­C2­00­00­0E
NnTB ­ Nearest non­TPMR Bridge ­ 01­80­C2­00­00­03
NCB ­ Nearest Customer Bridge ­ 01­80­C2­00­00­00
Total number of current entries: 1
LocalPort|Index|Remote Chassis ID |Remote Port|Remote System Name|DMAC
­­­­­­­­­|­­­­­|­­­­­­­­­­­­­­­­­ |­­­­­­­­­­­|­­­­­­­­­­­­­­­­­­|­­­­­
MGT | 1 | 00 00 00 00 11 00| 5 | C12 | NB
20 | 2 | 74 99 75 1c 75 00| 44 | C3+ | NB
534
G8052 Application Guide for ENOS 8.4
To view detailed information for a remote device, specify the Index number as found in the summary. For example, in keeping with the sample summary, to list details for the first remote device (with an Index value of 1), use the following command:
RS G8052(config)# show lldp remote­device 1
Local Port Alias: 3
Remote Device Index : 1
Remote Device TTL : 99
Remote Device RxChanges : false
Chassis Type : Mac Address
Chassis Id : 00­18­b1­33­1d­00
Port Type : Locally Assigned
Port Id : 23
Port Description : 7
System Name :
System Description: Lenovo Lenovo RackSwitch G8052, Lenovo Networking OS: version 8.4, Boot Image: version 8.4
System Capabilities Supported : bridge, router
System Capabilities Enabled
: bridge, router
Remote Management Address:
Subtype Address Interface Subtype
Interface Number Object Identifier
: IPv4
: 10.100.120.181
: ifIndex
: 128
:
Note: Received LLDP information can change very quickly. When using show commands, it is possible that flags for some expected events may be too short‐lived to be observed in the output.
© Copyright Lenovo 2016
Chapter 35: Link Layer Discovery Protocol
535
To view detailed information of all remote devices, use the following command: RS G8052# show lldp remote­device detail
Local Port Alias: MGTA Remote Device Index
: 1
Remote Device TTL
: 4678
Remote Device RxChanges
: false
Chassis Type
: Mac Address
Chassis Id
: 08­17­f4­a1­db­00
Port Type
: Locally Assigned
Port Id
: 25
Port Description
: MGTA
System Name
:
System Description
: Lenovo Lenovo RackSwitch G8052, Lenovo Networking OS: version 8.4, Boot Image: version 6.9.1.14
System Capabilities Supported : bridge, router
System Capabilities Enabled
: bridge, router
Remote Management Address:
Subtype
Address
Interface Subtype
Interface Number
Object Identifier
: IPv4
: 10.38.22.23
: ifIndex
: 127
:
Local Port Alias: 2
Remote Device Index
Remote Device TTL
Remote Device RxChanges
Chassis Type
Chassis Id
Port Type
Port Id
Port Description
: 2
: 4651
: false
: Mac Address
: 08­17­f4­a1­db­00
: Locally Assigned
: 2
: 2
System Name :
System Description
: Lenovo Lenovo RackSwitch G8052, Lenovo Networking OS: version 8.4, Boot Image: version 6.9.1.14
System Capabilities Supported : bridge, router
System Capabilities Enabled
: bridge, router
Remote Management Address:
Subtype
Address
Interface Subtype
Interface Number
Object Identifier
: IPv4
: 10.38.22.23
: ifIndex
: 127
:
Total entries displayed: 2
Time-to-Live for Received Information
Each remote device LLDP packet includes an expiration time. If the switch port does not receive an LLDP update from the remote device before the time‐to‐live clock expires, the switch will consider the remote information to be invalid, and will remove all associated information from the MIB.
536
G8052 Application Guide for ENOS 8.4
Remote devices can also intentionally set their LLDP time‐to‐live to 0, indicating to the switch that the LLDP information is invalid and must be immediately removed.
© Copyright Lenovo 2016
Chapter 35: Link Layer Discovery Protocol
537
LLDP Example Configuration
1. Turn LLDP on globally.
RS G8052(config)# lldp enable
2. Set the global LLDP timer features.
RS
RS
RS
RS
RS
G8052(config)# lldp refresh­interval 30(Transmit each 30 seconds)
G8052(config)# lldp transmission­delay 2(No more often than 2 sec.)
G8052(config)# lldp holdtime­multiplier 4(Remote hold 4 intervals)
G8052(config)# lldp reinit­delay 2 (Wait 2 sec. after reinit.)
G8052(config)# lldp trap­notification­interval 5(Minimum 5 sec. between)
3. Set LLDP options for each port.
RS
RS
RS
RS
RS
G8052(config)# interface port <n>
(Select a switch port)
G8052(config­if)# lldp admin­status tx_rx(Transmit and receive LLDP)
G8052(config­if)# lldp trap­notification(Enable SNMP trap notifications)
G8052(config­if)# lldp tlv all (Transmit all optional information)
G8052(config­if)# exit
4. Enable syslog reporting.
RS G8052(config)# logging log lldp
5. Verify the configuration settings:
RS G8052(config)# show lldp
6. View remote device information as needed.
RS G8052(config)# show lldp remote­device or
RS G8052(config)# show lldp remote­device <index number>
or
RS G8052(config)# show lldp remote­devices detail
538
G8052 Application Guide for ENOS 8.4
Chapter 36. Simple Network Management Protocol
Lenovo Enterprise Network Operating System provides Simple Network Management Protocol (SNMP) version 1, version 2, and version 3 support for access through any network management software, such as IBM Director or HP‐OpenView.
Note: SNMP read and write functions are enabled by default. For best security practices, if SNMP is not needed for your network, it is recommended that you disable these functions prior to connecting the switch to the network.
SNMP Version 1 & Version 2
To access the SNMP agent on the G8052, the read and write community strings on the SNMP manager must be configured to match those on the switch. The default read community string on the switch is public and the default write community string is private.
The read and write community strings on the switch can be changed using the following commands on the CLI: RS G8052(config)# snmp­server read­community <1‐32 characters>
‐and‐
RS G8052(config)# snmp­server write­community <1‐32 characters>
The SNMP manager must be able to reach the management interface or any one of the IP interfaces on the switch.
For the SNMP manager to receive the SNMPv1 traps sent out by the SNMP agent on the switch, configure the trap host on the switch with the following command: RS G8052(config)# snmp­server trap­source <trap source IP interface>
RS G8052(config)# snmp­server host <IPv4 address> <trap host community string>
Note: You can use a loopback interface to set the source IP address for SNMP traps. Use the following command to apply a configured loopback interface:
RS G8052(config)# snmp­server trap­source loopback <1‐5>
© Copyright Lenovo 2016
539
SNMP Version 3
SNMP version 3 (SNMPv3) is an enhanced version of the Simple Network Management Protocol, approved by the Internet Engineering Steering Group in March, 2002. SNMPv3 contains additional security and authentication features that provide data origin authentication, data integrity checks, timeliness indicators and encryption to protect against threats such as masquerade, modification of information, message stream modification and disclosure.
SNMPv3 allows clients to query the MIBs securely.
SNMPv3 configuration is managed using the following command path menu: RS G8052(config)# snmp­server ?
For more information on SNMP MIBs and the commands used to configure SNMP on the switch, see the Lenovo Enterprise Network Operating System 8.4 Command Reference.
Default Configuration
Enterprise NOS has three SNMPv3 users by default. All the three users have access to all the MIBs supported by the switch:
User 1 name is adminmd5 (password adminmd5). Authentication used is MD5. Privacy protocol used is DES.
 User 2 name is adminsha (password adminsha). Authentication used is SHA. Privacy protocol used is DES.
 User 3 name is adminshaaes (password Edpq132x!#9Zpx432w). Authentica‐
tion used is SHA. Privacy protocol used is AES‐128.

In boot strict mode (See “Boot Strict Mode” on page 52), Enterprise NOS has one SNMPv3 user:

User 1 name is adminshaaes (password Edpq132x!#9Zpx432w). Authentica‐
tion used is SHA. Privacy protocol used is AES‐128.
Up to 17 SNMP users can be configured on the switch. To modify an SNMP user, enter the following commands: RS G8052(config)# snmp­server user <1‐17> name <1‐32 characters>
Users can be configured to use the authentication/privacy options. The G8052 support two authentication algorithms: MD5 and SHA, as specified in the following command: RS G8052(config)# snmp­server user <1‐17> authentication­protocol {md5|sha} authentication­password
‐or‐
RS G8052(config)# snmp­server user <1‐17> authentication­protocol none
540
G8052 Application Guide for ENOS 8.4
User Configuration Example
1. To configure a user with name “admin,” authentication type MD5, and authentication password of “admin,” privacy option DES with privacy password of “admin,” use the following CLI commands. RS G8052(config)# snmp­server user 5 name admin
RS G8052(config)# snmp­server user 5 authentication­protocol md5 authentication­password
Changing authentication password; validation required: Enter current admin password:
<admin. password>
Enter new authentication password:
<auth. password; Should be more than 18 characters >
Re­enter new authentication password: <auth. password>
New authentication password accepted.
RS G8052(config)# snmp­server user 5 privacy­protocol des privacy­password
Changing privacy password; validation required:
Enter current admin password:
<admin. password>
Enter new privacy password:
Re­enter new privacy password:
New privacy password accepted.
<privacy password; Should be more than 18 characters>
<privacy password>
2. Configure a user access group, along with the views the group may access. Use the access table to configure the group’s access level. RS
RS
RS
RS
RS
G8052(config)# snmp­server access 5 name admingrp
G8052(config)# snmp­server access 5 level authpriv
G8052(config)# snmp­server access 5 read­view iso
G8052(config)# snmp­server access 5 write­view iso
G8052(config)# snmp­server access 5 notify­view iso
Because the read view, write view, and notify view are all set to “iso,” the user type has access to all private and public MIBs.
3. Assign the user to the user group. Use the group table to link the user to a particular access group. RS G8052(config)# snmp­server group 5 user­name admin
RS G8052(config)# snmp­server group 5 group­name admingrp
© Copyright Lenovo 2016
Chapter 36: Simple Network Management Protocol
541
Configuring SNMP Trap Hosts
Follow these instructions to configure SNMP trap hosts.
SNMPv1 Trap Host
1. Configure a user with no authentication and password.
RS G8052(config)# snmp­server user 10 name v1trap
2. Configure an access group and group table entries for the user. Use the following menu to specify which traps can be received by the user:
RS G8052(config)# snmp­server access <user number>
In the following example the user will receive the traps sent by the switch.
RS G8052(config)# snmp­server access 10 (Access group to view SNMPv1 traps)
name v1trap
security snmpv1
notify­view iso
RS G8052(config)# snmp­server group 10 (Assign user to the access group)
security snmpv1
user­name v1trap
group­name v1trap
3. Configure an entry in the notify table. RS G8052(config)# snmp­server notify 10 name v1trap
RS G8052(config)# snmp­server notify 10 tag v1trap
4. Specify the IPv4 address and other trap parameters in the targetAddr and targetParam tables. Use the following commands to specify the user name associated with the targetParam table: RS G8052(config)# snmp­server target­address 10 name v1trap address 10.70.70.190
RS G8052(config)# snmp­server target­address 10 parameters­name v1param
RS G8052(config)# snmp­server target­address 10 taglist v1param
RS G8052(config)# snmp­server target­parameters 10 name v1param
RS G8052(config)# snmp­server target­parameters 10 user­name v1only
RS G8052(config)# snmp­server target­parameters 10 message snmpv1
Note: ENOS 8.4 supports only IPv4 addresses for SNMPv1 and SNMPv2 trap hosts.
5. Use the community table to specify which community string is used in the trap.
RS G8052(config)# snmp­server community 10( Define the community string) index v1trap
name public
user­name v1trap 542
G8052 Application Guide for ENOS 8.4
SNMPv2 Trap Host Configuration
The SNMPv2 trap host configuration is similar to the SNMPv1 trap host configuration. Wherever you specify the model, use snmpv2 instead of snmpv1. RS G8052(config)# snmp­server user 10 name v2trap
RS
RS
RS
RS
RS
RS
G8052(config)# snmp­server group 10 security snmpv2
G8052(config)# snmp­server group 10 user­name v2trap
G8052(config)# snmp­server group 10 group­name v2trap
G8052(config)# snmp­server access 10 name v2trap
G8052(config)# snmp­server access 10 security snmpv2
G8052(config)# snmp­server access 10 notify­view iso
RS G8052(config)# snmp­server notify 10 name v2trap
RS G8052(config)# snmp­server notify 10 tag v2trap
RS G8052(config)# snmp­server target­address 10 name v2trap address 100.10.2.1
RS G8052(config)# snmp­server target­address 10 taglist v2trap
RS G8052(config)# snmp­server target­address 10 parameters­name v2param
RS G8052(config)# snmp­server target­parameters 10 name v2param
RS G8052(config)# snmp­server target­parameters 10 message snmpv2c
RS G8052(config)# snmp­server target­parameters 10 user­name v2trap
RS G8052(config)# snmp­server target­parameters 10 security snmpv2
RS G8052(config)# snmp­server community 10 index v2trap
RS G8052(config)# snmp­server community 10 user­name v2trap
Note: ENOS 8.4 supports only IPv4 addresses for SNMPv1 and SNMPv2 trap hosts.
© Copyright Lenovo 2016
Chapter 36: Simple Network Management Protocol
543
SNMPv3 Trap Host Configuration
To configure a user for SNMPv3 traps, you can choose to send the traps with both privacy and authentication, with authentication only, or without privacy or authentication.
This is configured in the access table using the following commands: RS G8052(config)# snmp­server access <1‐32> level
RS G8052(config)# snmp­server target­parameters <1‐16> level
Configure the user in the user table accordingly.
It is not necessary to configure the community table for SNMPv3 traps because the community string is not used by SNMPv3.
The following example shows how to configure a SNMPv3 user v3trap with authentication only: RS G8052(config)# snmp­server user 11 name v3trap
RS G8052(config)# snmp­server user 11 authentication­protocol md5 authentication­password
Changing authentication password; validation required: Enter current admin password:
<admin. password>
Enter new authentication password:
<auth. password>
Re­enter new authentication password: <auth. password>
New authentication password accepted.
RS G8052(config)# snmp­server access 11 notify­view iso
RS G8052(config)# snmp­server access 11 level authNopriv
RS G8052(config)# snmp­server group 11 user­name v3trap
RS G8052(config)# snmp­server group 11 group­name v3trap
RS G8052(config)# snmp­server notify 11 name v3trap
RS G8052(config)# snmp­server notify 11 tag v3trap
RS G8052(config)# snmp­server target­address 11 name v3trap address 47.81.25.66
RS G8052(config)# snmp­server target­address 11 taglist v3trap
RS G8052(config)# snmp­server target­address 11 parameters­name v3param
RS G8052(config)# snmp­server target­parameters 11 name v3param
RS G8052(config)# snmp­server target­parameters 11 user­name v3trap
RS G8052(config)# snmp­server target­parameters 11 level authNoPriv
544
G8052 Application Guide for ENOS 8.4
SNMP MIBs
The ENOS SNMP agent supports SNMP version 3. Security is provided through SNMP community strings. The default community strings are “public” for SNMP GET operation and “private” for SNMP SET operation. The community string can be modified only through the Industry Standard Command Line Interface (ISCLI). Detailed SNMP MIBs and trap definitions of the ENOS SNMP agent are contained in the ENOS enterprise MIB document.
The ENOS SNMP agent supports the following standard MIBs:

























dot1x.mib
ieee8021ab.mib
ieee8023ad.mib
rfc1213.mib
rfc1215.mib
rfc1493.mib
rfc1573.mib
rfc1643.mib
rfc1657.mib
rfc1757.mib
rfc1850.mib
rfc1907.mib
rfc2037.mib
rfc2233.mib
rfc2465.mib
rfc2571.mib
rfc2572.mib
rfc2573.mib
rfc2574.mib
rfc2575.mib
rfc2576.mib
rfc2790.mib
rfc3176.mib
rfc4133.mib
rfc4363.mib
The ENOS SNMP agent supports the following generic traps as defined in RFC 1215:
ColdStart
WarmStart
 LinkDown
 LinkUp
 AuthenticationFailure


The SNMP agent also supports two Spanning Tree traps as defined in RFC 1493:


© Copyright Lenovo 2016
NewRoot
TopologyChange
Chapter 36: Simple Network Management Protocol
545
The following are the enterprise SNMP traps supported in ENOS: Table 36. Enterprise NOS‐Supported Enterprise SNMP Traps
546
Trap Name
Description
swLoginFailure
Signifies that someone failed to enter a valid username/password combination. swTrapDisplayString specifies whether the login attempt was from CONSOLE or TELNET. In case of TELNET login it also specifies the IP address of the host from which the attempt was made.
swValidLogin
Signifies that a user login has occurred.
swApplyComplete
Signifies that new configuration has been applied.
swSaveComplete
Signifies that new configuration has been saved.
swFwDownloadSucess
Signifies that firmware has been downloaded to [image1|image2|boot image].
swFwDownloadFailure
Signifies that firmware downloaded failed to [image1|image2|boot image].
swValidLogout
Signifies that a user logout has occurred.
swPrimaryPowerSupplyFailure
Signifies that the primary power supply has failed.
swPrimaryPowerSupplyFixed
Signifies that the primary power supply has been restored.
swDefAdminDisable
Signifies that the default admin account has been disabled.
swAcntStrngPswdNotMet
Signifies that the configured password does not match strong password complexity.
swAcntLocked Signifies that account has been locked.
swAcntUnlocked Signifies that account has been unlocked.
swStgNewRoot
Signifies that the bridge has become the new root of the STG.
G8052 Application Guide for ENOS 8.4
Table 36. Enterprise NOS‐Supported Enterprise SNMP Traps (continued)
© Copyright Lenovo 2016
Trap Name
Description
swCistNewRoot
Signifies that the bridge has become the new root of the CIST.
swStgTopologyChanged
Signifies that there was a STG topology change.
swCistTopologyChanged
Signifies that there was a CIST topology change.
swHotlinksMasterUp
Signifies that the Master interface is active.
swHotlinksMasterDn
Signifies that the Master interface is not active.
swHotlinksBackupUp
Signifies that the Backup interface is active.
swHotlinksBackupDn
Signifies that the Backup interface is not active.
swHotlinksNone
Signifies that there are no active interfaces.
swTeamingCtrlUp
Signifies that the teaming is up.
swTeamingCtrlDown
Signifies that the teaming control is down.
swTeamingCtrlDownTearDownBlked
Signifies that the teaming control is down but teardown is blocked.
swTeamingCtrlError
Signifies error, action is undefined.
swLACPPortBlocked
Signifies that LACP is operationally down on a port, and traffic is blocked on the port.
swLACPPortUnblocked
Signifies that LACP is operationally up on a port, and traffic is no longer blocked on the port.
swLFDPortErrdisabled
Signifies that a port is error‐disabled due to excessive link flaps.
swVlagInstanceUp
Signifies that VLAG instance is up identified in the trap message.
swVlagInstanceRemoteUp
Signifies that VLAG is down but instance on the remote instance is up.
swVlagInstanceLocalUp
Signifies that VLAG is down but local instance is up.
Chapter 36: Simple Network Management Protocol
547
Table 36. Enterprise NOS‐Supported Enterprise SNMP Traps (continued)
548
Trap Name
Description
swVlagInstanceDown
Signifies that VLAG instance is down identified in the trap message.
swVlagIslUp
Signifies that connection between VLAG switches is up.
swVlagIslDown
Signifies that connection between VLAG switches is down.
sw8021x
Signifies 802.1x feature is enabled.
swDefGwUp
Signifies that the default gateway is alive. ipCurCfgGwIndex is the index of the Gateway in ipCurCfgGwTable. The range for ipCurCfgGwIndex is from 1 to ipGatewayTableMax. ipCurCfgGwAddr is the IP address of the default gateway.
swDefGwDown
Signifies that the default gateway is down. ipCurCfgGwIndex is the index of the Gateway in ipCurCfgGwTable. The range for ipCurCfgGwIndex is from 1 to ipGatewayTableMax. ipCurCfgGwAddr is the IP address of the default gateway.
swDefGwInService
Signifies that the default gateway is up and in service. ipCurCfgGwIndex is the index of the Gateway in ipCurCfgGwTable. The range for ipCurCfgGwIndex is from 1 to ipGatewayTableMax. ipCurCfgGwAddr is the IP address of the default gateway.
swDefGwNotInService
Signifies that the default gateway is alive but not in service. ipCurCfgGwIndex is the index of the Gateway in ipCurCfgGwTable. The range for ipCurCfgGwIndex is from 1 to ipGatewayTableMax. ipCurCfgGwAddr is the IP address of the default gateway.
G8052 Application Guide for ENOS 8.4
Table 36. Enterprise NOS‐Supported Enterprise SNMP Traps (continued)
© Copyright Lenovo 2016
Trap Name
Description
swVrrpNewMaster
Indicates that the sending agent has transitioned to “Master” state. vrrpCurCfgVirtRtrIndx is the VRRP virtual router table index referenced in vrrpCurCfgVirtRtrTable. The range is from 1 to vrrpVirtRtrTableMaxSize. vrrpCurCfgVirtRtrAddr is the VRRP virtual router IP address.
swVrrpNewBackup
Indicates that the sending agent has transitioned to “Backup” state. vrrpCurCfgVirtRtrIndx is the VRRP virtual router table index referenced in vrrpCurCfgVirtRtrTable. The range is from 1 to vrrpVirtRtrTableMaxSize. vrrpCurCfgVirtRtrAddr is the VRRP virtual router IP address.
swVrrpAuthFailure
Signifies that a packet has been received from a router whose authentication key or authentication type conflicts with this routerʹs authentication key or authentication type. Implementation of this trap is optional. vrrpCurCfgIfIndx is the VRRP interface index. This is equivalent to ifIndex in RFC 1213 mib. The range is from 1 to vrrpIfTableMaxSize. vrrpCurCfgIfPasswd is the password for authentication. It is a DisplayString of 0 to 7 characters.
Chapter 36: Simple Network Management Protocol
549
Table 36. Enterprise NOS‐Supported Enterprise SNMP Traps (continued)
550
Trap Name
Description
swTcpHoldDown
Signifies that new TCP connection requests from a particular client will be blocked for a pre‐determined amount of time since the rate of new TCP connections from that client has reached a pre‐determined threshold. The fltCurCfgSrcIp is the client source IP address for which new TCP connection requests will be blocked. The swTrapRate specifies the amount of time in minutes that the particular client will be blocked.
swNTPSyncFailed
Signifies that synchronization with the NTP server has failed.
swNTPUpdateClock
Signifies that the system clock is updated with NTP server.
swECMPGatewayUp
Signifies that the ECMP gateway is up.
swECMPGatewayDown
Signifies that the ECMP gateway is down.
swTempExceedThreshold
Signifies that the switch temperature has exceeded maximum safety limits.
swFanFailure
Signifies that fan failure has been detected.
swFanFailureFixed
Signifies that the fan failure has been fixed.
swTempReturnThreshold
Signifies that the switch temperature has returned to under maximum safety limits.
swVMGroupVMotion
Signifies that a virtual machine has moved from a port to another.
swVMGroupVMOnline
Signifies that an advance provisioned virtual machine has came online.
swVMGroupVMVlanChange
Signifies that a virtual machine has entered a VLAN, or changed the VLAN.
swVmCheckSpoofedvm
Signifies that a spoofed VM MAC was found.
G8052 Application Guide for ENOS 8.4
Table 36. Enterprise NOS‐Supported Enterprise SNMP Traps (continued)
© Copyright Lenovo 2016
Trap Name
Description
swOflowConnectControllerFailure
Signifies that the connection to OpenFlow controller is broken.
swOflowConnectControllerSuccess
Signifies that the connection to OpenFlow controller is successful.
swOflowEmergencyState
Signifies that the OpenFlow switch has moved to emergency state.
swOflowNoEmergencyState
Signifies that the OpenFlow switch is out of emergency state.
swOflowSwitchOflowMode
Signifies that the device is working in OpenFlow switch mode.
swOflowSwitchNomalMode
Signifies that the device is working in normal switch mode.
swOflowSwitchFlowtableClr
Signifies that the flow table entries are cleared from the device.
swOflowSwitchStatsClr
Signifies that the OpenFlow statistics are cleared from the device.
swOflowFlowtableEntryUnavail
Signifies that the device is unable to add flow entry in OpenFlow due to unavailability of system resources.
swOflowFlowtableLimit
Signifies that the device has reached its configured flow limit.
swOflowPortDownController
Signifies that the port is operationally down by OpenFlow controller.
swOflowPortUpController
Signifies that the port is operationally up by OpenFlow controller.
swOflowVersionNegotiationError
Signifies that the device is unable to connect to controller either due to bad version, or negotiation/hello failure.
Chapter 36: Simple Network Management Protocol
551
Switch Images and Configuration Files
This section describes how to use MIB calls to work with switch images and configuration files. You can use a standard SNMP tool to perform the actions, using the MIBs listed in the table below. The table lists the MIBS used to perform operations associated with the Switch Image and Configuration files. Table 37. MIBs for Switch Image and Configuration Files
MIB Name
MIB OID
agTransferServer 1.3.6.1.4.1.26534.2.7.7.1.1.7.1
agTransferImage
1.3.6.1.4.1.26534.2.7.7.1.1.7.2
agTransferImageFileName
1.3.6.1.4.1.26534.2.7.7.1.1.7.3
agTransferCfgFileName 1.3.6.1.4.1.26534.2.7.7.1.1.7.4
agTransferDumpFileName
1.3.6.1.4.1.26534.2.7.7.1.1.7.5
agTransferAction
1.3.6.1.4.1.26534.2.7.7.1.1.7.6
agTransferLastActionStatus 1.3.6.1.4.1.26534.2.7.7.1.1.7.7
agTransferUserName
1.3.6.1.4.1.26534.2.7.7.1.1.7.9
agTransferPassword
1.3.6.1.4.1.26534.2.7.7.1.1.7.10
agTransferTSDumpFileName
1.3.6.1.4.1.26534.2.7.7.1.1.7.11
The following SNMP actions can be performed using the MIBs listed in the table:
552

Load a new Switch image (boot or running) from an FTP, SFTP, or TFTP server 
Load a previously saved switch configuration from an FTP, SFTP, or TFTP server

Save the switch configuration to an FTP, SFTP, or TFTP server

Save a switch dump to an FTP, SFTP, or TFTP server
G8052 Application Guide for ENOS 8.4
Loading a New Switch Image
To load a new switch image with the name “MyNewImage­1.img” into image2, follow these steps. This example shows an FTP, SFTP, or TFTP server at IPv4 address 192.168.10.10, though IPv6 is also supported.
1. Set the FTP, SFTP, or TFTP server address where the switch image resides: Set agTransferServer.0 "192.168.10.10"
2. Set the area where the new image will be loaded: Set agTransferImage.0 "image2"
3. Set the name of the image:
Set agTransferImageFileName.0 "MyNewImage­1.img"
4. If you are using an FTP or SFTP server, enter a username: Set agTransferUserName.0 "MyName"
5. If you are using an FTP or SFTP server, enter a password: Set agTransferPassword.0 "MyPassword"
6. Initiate the transfer. To transfer a switch image, enter 2 (gtimg): Set agTransferAction.0 "2"
Loading a Saved Switch Configuration
To load a saved switch configuration with the name “MyRunningConfig.cfg” into the switch, follow these steps. This example shows an FTP, SFTP, or TFTP server at IPv4 address 192.168.10.10, though IPv6 is also supported. 1. Set the FTP, SFTP, or TFTP server address where the switch Configuration File resides: Set agTransferServer.0 "192.168.10.10"
2. Set the name of the configuration file: Set agTransferCfgFileName.0 "MyRunningConfig.cfg"
3. If you are using an FTP or SFTP server, enter a username: Set agTransferUserName.0 "MyName"
4. If you are using an FTP or SFTP server, enter a password: Set agTransferPassword.0 "MyPassword"
5. Initiate the transfer. To restore a running configuration, enter 3: Set agTransferAction.0 "3"
© Copyright Lenovo 2016
Chapter 36: Simple Network Management Protocol
553
Saving the Switch Configuration
To save the switch configuration to a file server, follow these steps. This example shows an FTP, SFTP, or TFTP server at IPv4 address 192.168.10.10, though IPv6 is also supported. 1. Set the FTP, SFTP, or TFTP server address where the configuration file is saved:
Set agTransferServer.0 "192.168.10.10"
2. Set the name of the configuration file: Set agTransferCfgFileName.0 "MyRunningConfig.cfg"
3. If you are using an FTP or SFTP server, enter a username: Set agTransferUserName.0 "MyName"
4. If you are using an FTP or SFTP server, enter a password: Set agTransferPassword.0 "MyPassword"
5. Initiate the transfer. To save a running configuration file, enter 4: Set agTransferAction.0 "4"
Saving a Switch Dump
To save a switch dump to a file server, follow these steps. This example shows an FTP, SFTP, or TFTP server at 192.168.10.10, though IPv6 is also supported. 1. Set the FTP, SFTP, or TFTP server address where the configuration will be saved: Set agTransferServer.0 "192.168.10.10"
2. Set the name of dump file: Set agTransferDumpFileName.0 "MyDumpFile.dmp"
3. If you are using an FTP or SFTP server, enter a username: Set agTransferUserName.0 "MyName"
4. If you are using an FTP or SFTP server, enter a password: Set agTransferPassword.0 "MyPassword"
5. Initiate the transfer. To save a dump file, enter 5: Set agTransferAction.0 "5"
554
G8052 Application Guide for ENOS 8.4
Chapter 37. Service Location Protocol
Service Location Protocol (SLP) allows the switch to provide dynamic directory services that help users find servers by attributes rather than by name or address. SLP eliminates the need for a user to know the name of a network host supporting a service. SLP allows the user to bind a service description to the network address of the service.
Service Location Protocol is described in RFC 2608. SLP defines specialized components called agents that perform tasks and support services as follows:

User Agent (UA) supports service query functions. It requests service information for user applications. The User Agent retrieves service information from the Service Agent or Directory Agents. A Host On‐Demand client is an example of a User Agent.

Service Agent (SA) provides service registration and service advertisement. Note: In this release, SA supports UA/DA on Linux with SLPv2 support. 
Directory Agent (DA) collects service information from Service Agents to provide a repository of service information in order to centralize it for efficient access by User Agents. There can only be one Directory Agent present per given host. The Directory Agent acts as an intermediate tier in the SLP architecture, placed between the User Agents and the Service Agents, so they communicate only with the Directory Agent instead of with each other. This eliminates a large portion of the multicast request or reply traffic on the network, and it protects the Service Agents from being overwhelmed by too many service requests. Services are described by the configuration of attributes associated with a type of service. A User Agent can select an appropriate service by specifying the attributes that it needs in a service request message. When service replies are returned, they contain a Uniform Resource Locator (URL) pointing to the service desired, and other information, such as server load, needed by the User Agent.
© Copyright Lenovo 2016
Chapter 37: Service Location Protocol
555
Active DA Discovery
When a Service Agent or User Agent initializes, it can perform Active Directory Agent Discovery using a multicast service request and specifies the special, reserved service type (service:directory-agent). Active DA Discovery is achieved through the same mechanism as any other discovery using SLP. The Directory Agent replies with unicast service replies, which provides the URLs and attributes of the requested service.
556
G8052 Application Guide for ENOS 8.4
SLP Configuration
Use the following ISCLI commands to configure SLP for the switch: Table 38. SLP ISCLI Commands
Command Syntax and Usage
[no] ip slp enable
Enables or disables SLP on the switch. Command mode: Global configuration
[no] ip slp active-da-discovery enable
Enables or disables Active DA Discovery. Command mode: Global configuration
ip slp active-da-discovery-start-wait-time <1‐10>
Configures the wait time before starting Active DA Discovery, in seconds. The default value is 3 seconds. Command mode: Global configuration
clear ip slp directory-agents
Clears all Directory Agents learned by the switch. Command mode: Global configuration
show ip slp information
Displays SLP information. Command mode: All show ip slp directory­agents Displays Directory Agents learned by the switch. Command mode: All show ip slp user­agents Displays User Agents information. Command mode: All show ip slp counter
Displays SLP statistics. Command mode: All clear ip slp counters
Clears all Directory Agents learned by the switch. Command mode: Global configuration
© Copyright Lenovo 2016
Chapter 37: Service Location Protocol
557
558
G8052 Application Guide for ENOS 8.4
Chapter 38. NETCONF
The Network Configuration Protocol (NETCONF) provides a mechanism to manage the G8052, retrieve or modify existing configuration data, and upload new configuration data. See RFC 4741 for details on NETCONF.
NETCONF operates in a client/server model. The NETCONF client establishes a session with the switch (acting as a NETCONF server) using a Remote Procedure Call (RPC). NETCONF is based on the Extensible Markup Language (XML) for encoding data and for exchanging configuration and protocol messages.
The following topics are discussed in this section:
© Copyright Lenovo 2016

“NETCONF Overview” on page 560

“XML Requirements” on page 561

“Installing the NETCONF Client” on page 562

“Using Juniper Perl Client” on page 564

“Establishing a NETCONF Session” on page 565

“NETCONF Operations” on page 567

“Protocol Operations Examples” on page 568
559
NETCONF Overview
NETCONF provides a method to quickly configure the switch. It also allows you to implement a configuration across multiple switches, thereby saving time and reducing the chances of configuration errors.
The NETCONF protocol defines basic operations that are equivalent to the switch ISCLI commands.
Note: The current implementation of NETCONF supports only ISCLI commands.
NETCONF is a connection‐oriented protocol. See Figure 51 for an overview of NETCONF operation.
Figure 51. NETCONF Operations Procedure
<hello>
<capabilities/>
</hello>
<hello>
<capabilities/>
</hello>
<rpc>
<operation/>
</rpc>
NETCONF
Client
<rpc-reply>
<operation-response/>
</rpc-reply>
<rpc>
<close-session/>
</rpc>
NETCONF
Server
<rpc-reply>
<ok/>
</rpc-reply>
Session
• Session-ID
Transport Layer
Protocol
Connection
• Authentication
• Data integrity
• Confidentiality
Transport Layer
Protocol
1. The client establishes a transport layer connection to the switch (acting as a NETCONF server).
2. The client and switch exchange hello messages to declare their capabilities.
3. The client sends a request via rpc message to the switch.
4. The switch sends a response via rpc­reply message to the client.
Note: Steps 3 and 4 must be repeated for each request that the client sends to the switch.
5. The client sends a close­session message to the switch to end the NETCONF session and the transport layer connection.
6. The switch sends an ok response.
560
G8052 Application Guide for ENOS 8.4
XML Requirements
XML is the encoding format used within NETCONF. When using XML for NETCONF:

All NETCONF protocol elements are defined in the following namespace:
urn:ietf:params:xml:ns:netconf:base:1.0

NETCONF capability names must be Uniform Resource Identifiers (URIs):
urn:ietf:params:netconf:capability:{name}:1.0
where {name} is the name of the capability.

Document type declarations must not appear in the NETCONF content.

For Secure Shell (SSH), you must use a special message termination sequence of six characters to provide message framing:
]]>]]>
© Copyright Lenovo 2016
Chapter 38: NETCONF
561
Installing the NETCONF Client
You can download the required NETCONF Client installation files from www.ibm.com. Select Support & downloads > Fixes, updates and drivers. Follow instructions on the IBM Support Portal page to find the files.
Before installing the NETCONF client, ensure you have completed the following tasks:

Install a supported version of Python (Python 2.6 or higher, up to but not including Python 3.0) in the folder C:\.

Install the PyCrypto application appropriate to the Python version you are using.
Note: The following steps are for the Windows operating systems.
Follow these steps to install the Blade NETCONF Python Client (BNClient):
1. Extract the file blade­netconf­python­client­v0.1.zip to the following folder:
C:\
Under the root folder C:\blade­netconf­python­client­v0.1, you will see two folders:

blade­netconf­python­client

python­library
Note: Make sure Paramiko version 1.7.4 or higher is in the folder C:\blade­netconf­python­client­v0.1\python­ssh­library\
2. Open the command prompt (Select Start > Run > cmd).
3. Enter the following command to install the SSH library: python C:\blade­netconf­python­client­v0.1\python­ssh­library\
paramiko­1.7.6\setup.py install
Note: If the python command does not work from the command prompt, you may need to add a system variable to set the path to the directory where you have installed Python. You can add the system variable at the following location: My
Computer > Properties > Advanced > Environment Variables
562
G8052 Application Guide for ENOS 8.4
4. Follow these steps to install BNClient:
As a python script:
a. Enter the following command for help: python C:\blade­netconf­python­client­v0.1\blade­netconf­python­
client\bnclient\bnclient.py –h
b. Enter the following command to establish a NETCONF session:

Using SSH to connect to default port 830: python C:\blade­netconf­python­client­v0.1\blade­netconf­python­
client\bnclient\bnclient.py {switch IP address} –u admin –p admin –o get

Using SSH to connect to port 22: python C:\blade­netconf­python­client­v0.1\blade­netconf­python­
client\bnclient\bnclient.py {switch IP address}:22 –u admin –p admin –o get
As a python library:
a. Open the file C:\blade­netconf­python­client­v0.1\blade­netconf­
python­client\example\get.py in a Python editor (For example, IDLE).
b. Change the IP address in the hostname field to the switch IP address, and save the file.
c. Enter the following command to establish a session:
python C:\blade­netconf­python­client­v0.1\blade­netconf­python­
client\setup.py install
d. Enter the following command to get the running configuration:
python C:\blade­netconf­python­client­v0.1\blade­netconf­python­
client\example\get.py
Note: The file get.py is an example of a NETCONF operation python script. You can edit the script or write a new script as per your requirements.
© Copyright Lenovo 2016
Chapter 38: NETCONF
563
Using Juniper Perl Client
You can use Juniper Perl client instead of BNClient to communicate with the NETCONF feature on the switch. Follow these steps to use the Juniper Perl client.
Note: You must use the Linux operating system for the Juniper Perl client.
1. Extract the file juniper­netconf­perl­client.zip to the folder:
/home/user/
You will see two folders:

juniper­netconf­perl­client

blade­netconf­perl­scripts
2. Follow these steps to install the Juniper Perl client:
As a Perl library:
a. Change to the following directory:
/home/user/juniper­netconf­perl­client
b. Extract the following file:
netconf­perl­10.0R2.10.tar.gz
c. Change to the following directory:
/home/user/juniper­netconf­perl­client/netconf­perl­10.0R2
.10
d. Install the client as per the instructions in the README file.
Note: If the prerequisites package installation fails, manually install each file in /home/user/juniper­netconf­perl­client\netconf­perl­prereqs­
patch.
As a Perl script:
a. Change to the following directory:
/home/user/blade­netconf­perl­scripts/
b. Enter the following command:
perl get/get.pl ­l admin ­p admin {swich IP address}
Note: get.pl is an example of a NETCONF operation Perl script. You can edit the script or write a new script as per your requirement.
564
G8052 Application Guide for ENOS 8.4
Establishing a NETCONF Session
SSH is the widely used protocol for NETCONF sessions. The default SSH port for NETCONF is 830. The client may also connect to the switch through SSH port 22.
Follow these steps to establish a NETCONF session. Enter commands in the client Linux Shell.
Note: You can open a maximum of four simultaneous sessions.
1. Enter the following command to open an SSH connection:
ssh admin@{switch IP address} ­p 830 ­s netconf
2. Type or paste the following hello message:
<hello>
<capabilities>
<capability>urn:ietf:params:netconf:base:1.0</capability>
</capabilities>
</hello>
]]>]]>
The switch returns a hello message:
<hello xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<capabilities>
<capability>urn:ietf:params:netconf:base:1.0</capability>
<capability>urn:ietf:params:netconf:capability:writable­running:1.0</capab
ility>
<capability>urn:ietf:params:netconf:capability:rollback­on­error:1.0</capa
bility>
<capability>urn:ietf:params:netconf:capability:startup:1.0</capability>
</capabilities> <session­id>102</session­id> </hello> ]]>]]>
3. Type or paste the following rpc message. The get operation is used as an example.
<rpc message­id=“100”>
<get>
<filter type=“subtree”>
<configuration­text/>
</filter>
</get>
</rpc>
]]>]]> © Copyright Lenovo 2016
Chapter 38: NETCONF
565
The switch sends an rpc­reply message:
<rpc­reply message­id=“100”>
<data>
<configuration­text xmlns=“http://www.ibm.com/netconf/1.0/config­text”> version “8.4.1”
switch­type “Lenovo Lenovo RackSwitch G8052”
!
!
no system dhcp mgta
!
!
interface ip 127 ip address 172.31.36.51
enable
exit
!
ip gateway 3 address 172.31.1.1
ip gateway 3 enable
!
!
end
</configuration­text>
</data>
</rpc­reply>
]]>]]>
Note: Repeat Step 3 for each request you need to send to the switch.
4. Type or paste the following close­session message to close the NETCONF session and terminate the SSH connection.
<rpc message­id=“101”>
<close­session/>
</rpc>
]]>]]>
The switch sends the following response:
<rpc­reply message­id=“101”>
<ok/>
</rpc­reply>
]]>]]>
566
G8052 Application Guide for ENOS 8.4
NETCONF Operations
The NETCONF protocol provides a set of operations to manage and retrieve switch configuration. Table 39 provides a list of protocol operations supported by the switch.
Table 39. Protocol Operations
© Copyright Lenovo 2016
Operation
Description
get­config
Retrieve all or part of the running or startup configuration.
edit­config
Load all or part of a specified configuration to the running or startup configuration.
copy­config
Replace the target running or startup configuration with a source running or startup configuration.
delete­config
Delete startup configuration.
lock
Lock the running configuration to prevent other users (via another NETCONF session) from changing it.
unlock
Release a locked running configuration.
get
Retrieve running configuration and device state information.
close­session
Request graceful termination of a NETCONF session.
kill­session
Force the termination of a NETCONF session.
get­configuration
Retrieve configuration data from the switch.
get­interface­information
Retrieve interface status information.
Chapter 38: NETCONF
567
Protocol Operations Examples
Following are examples of the NETCONF protocol operations supported by the G8052.
<get-config>
Usage:
<rpc message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<get­config>
<source>
<running/>
</source>
<filter type=“subtree”>
<configuration­text xmlns=“http://www.ibm.com/netconf/1.0/config­text”/>
</filter>
</get­config>
</rpc>
Response from the switch:
<rpc­reply message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<data>
<configuration­text xmlns=“http://www.ibm.com/netconf/1.0/config­text”>
<!­­ configuration text... ­­>
</configuration­text>
</data>
</rpc­reply>
See Table 40 for the tag elements and their values.
Table 40. get­config Tag Element Values
568
Tag Element
Description
Value
source
The configuration text you want to retrieve.
running/ or startup/
filter type=“subtree”
The filter type.
subtree
!­­configuration text...­­
Contains the running configuration in ISCLI format.
G8052 Application Guide for ENOS 8.4
<edit-config>
Usage:
<rpc message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<edit­config>
<target>
<running/>
</target>
<default­operation>
<merge/>
</default­operation>
<error­option>
<stop­on­error/>
</error­option>
<config­text xmlns=“http://www.ibm.com/netconf/1.0/config­text”>
<configuration­text>hostname Router</configuration­text>
</config­text>
</edit­config>
</rpc>
Response from the switch:
<rpc­reply message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<ok/>
</rpc­reply>
See Table 41 for the tag elements and their values.
Table 41. edit­config Tag Element Values
© Copyright Lenovo 2016
Tag Element
Description
Value
target
The configuration you want to edit.
running/ or startup/
Chapter 38: NETCONF
569
Table 41. edit­config Tag Element Values
Tag Element
Description
Value
default­operation Set the default  merge: The new operation for the configuration is merged edit­config request.
with the target configuration at the corresponding level.
error­option
570
G8052 Application Guide for ENOS 8.4

replace: The new configuration replaces the target configuration.

none: The target configuration does not change unless the configuration data in the configuration­text parameter uses the operation attribute to request a different operation.
Set the option to handle  stop­on­error: Abort configuration error.
the edit­config operation on first error. This is the default error‐option.

continue­on­error: Continue to process configuration data on error.

rollback­on­error: Abort the edit­config operation on first error and discard the requested configuration changes.
<copy-config>
Usage:
<rpc message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<copy­config>
<target>
<startup/>
</target>
<source>
<running/>
</source>
</copy­config>
</rpc>
Response from the switch:
<rpc­reply message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<ok/>
</rpc­reply>
See Table 42 for the tag elements and their values.
Table 42. copy­config Tag Element Values
© Copyright Lenovo 2016
Tag Element
Description
Value
target
Configuration that needs to be changed. running/ or startup/
source
Source configuration.
running/ or startup/
Chapter 38: NETCONF
571
<delete-config>
Usage:
<rpc message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<delete­config>
<target>
<startup/>
</target>
</delete­config>
</rpc>
Response from the switch:
<rpc­reply message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<ok/>
</rpc­reply>
See Table 43 for the tag elements and their values.
Table 43. delete­config Tag Element Values
Tag Element
Description
Value
target
Configuration that needs to be deleted.
startup/
<lock>
Usage:
<rpc message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<lock>
<target>
<running/>
</target>
</lock>
</rpc>
Response from the switch:
<rpc­reply message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<ok/>
</rpc­reply>
See Table 44 for the tag elements and their values.
Table 44. lock Tag Element Values
572
Tag Element
Description
Value
target
Configuration that needs to be edited.
running/
G8052 Application Guide for ENOS 8.4
<unlock>
Usage:
<rpc message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<unlock>
<target>
<running/>
</target>
</unlock>
</rpc>
Response from the switch:
<rpc­reply message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<ok/>
</rpc­reply>
See Table 45 for the tag elements and their values.
Table 45. unlock Tag Element Values
© Copyright Lenovo 2016
Tag Element
Description
Value
target
Configuration being edited.
running/
Chapter 38: NETCONF
573
<get>
Usage:
<rpc message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<get>
<filter type=“subtree”>
<!­­ request a text version of the configuration ­­>
<configuration­text xmlns=“http://www.ibm.com/netconf/1.0/config­text”/>
</filter>
</get>
</rpc>
Response from the switch:
<rpc­reply message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<data>
<configuration­text xmlns=“http://www.ibm.com/netconf/1.0/config­text”>
<!­­ configuration text... ­­>
</configuration ­text>
</data>
</rpc­reply>
See Table 46 for the tag elements and their values.
Table 46. get Tag Element Values
574
Tag Element
Description
Value
filter
Filter type.
subtree
configuration­text
Configuration in ISCLI format.
G8052 Application Guide for ENOS 8.4
<close-session>
Usage:
<rpc message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<close­session/>
</rpc>
Response from the switch:
<rpc­reply message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<ok/>
</rpc­reply>
<kill-session>
Usage:
<rpc message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<kill­session>
<session­id>4</session­id>
</kill­session>
</rpc>
Response from the switch:
<rpc­reply message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<ok/>
</rpc­reply>
See Table 47 for the tag elements and their values.
Table 47. kill­session Tag Element Values
© Copyright Lenovo 2016
Tag Element
Description
session­id
ID number of the session to be killed
Chapter 38: NETCONF
575
<get-configuration>
Usage:
<rpc message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<get­configuration database=“commited” format=“text”/>
</rpc>
Response from the switch:
<rpc­reply message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<data>
<configuration­text xmlns=“http://www.ibm.com/netconf/1.0/config­text”>
<!­­ configuration text... ­­>
</configuration ­text>
</data>
</rpc­reply>
See Table 48 for the tag elements and their values.
Table 48. get­configuration Tag Element Values
Tag Element
Description
Attributes
get­configuratio
n
Retrieve the configuration.
database ‐ supports only committed
format ‐ supports only text
576
G8052 Application Guide for ENOS 8.4
<get-interface-information>
Usage:
<rpc message­id=“101”>
<get­interface­information>
<interface­name> port xx </interface­name>
<brief/>
</get­interface­information>
</rpc>
Response from switch: 
Port detail information
<rpc­reply message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<interface­information>
<physical­interface>
<name></name> <admin­status></admin­status>
<oper­status></oper­status>
<local­index></local­index>
<if­type></if­type>
<link­level­type></link­level­type>
<mtu></mtu>
<speed></speed>
<link­type></link­type>
<traffic­statistics>
<input­bytes></input­bytes>
<output­bytes></output­bytes>
<input­packets></input­packets>
<output­packets></output­packets>
</traffic­statistics>
<input­error­list>
<input­errors></input­errors>
<framing­errors></framing­errors>
<input­giants></input­giants>
<input­discards></input­discards>
</input­error­list>
<output­error­list>
<output­collisions></output­collisions> <output­errors></output­errors>
<output­drops></output­drops>
</output­error­list>
</physical­interface>
</interface­information>
</rpc­reply>
© Copyright Lenovo 2016
Chapter 38: NETCONF
577

IP detail information
<rpc­reply message­id=“101” xmlns=“urn:ietf:params:xml:ns:netconf:base:1.0”>
<interface­information>
<physical­interface>
<logical­interface>
<name></name>
<local­index></local­index>
<address­family>
<address­family­name></address­family­name>
<mtu></mtu>
<interface­address>
<ifa­destination></ifa­destination>
<ifa­local></ifa­local>
<ifa­broadcast></ifa­broadcast>
</interface­address>
</address­family>
</logical­interface>
</physical­interface>
</interface­information>
</rpc­reply>
See Table 49 for the tag elements and their values.
Table 49. get­interface­information Tag Element Values
578
Tag Element
Description
interface­name
Interface name or number. You can use the tags brief/ or detail/ to specify the amount of information you need.
name
Name of the port or IP interface.
admin­status
Administration status of port interface; shutdown or no shutdown.
oper­status
Operational status of port interface; link‐up or link‐down.
local­index
Local index of port.
if­type
Type of port; GE, XGE.
link­level­type
Ethernet
mtu
9216 for port; 1500 for IP interface.
speed
Speed of port; 1000M, 10000M.
link­type
Type of duplex port; full, half.
input­bytes
Number of bytes received at the port.
output­bytes
Number of bytes sent from the port.
input­packets
Number of frames received at port.
output­packets
Number of frames sent out from the port.
G8052 Application Guide for ENOS 8.4
Table 49. get­interface­information Tag Element Values
© Copyright Lenovo 2016
Tag Element
Description
input­errors
Sum of discarded frames and FCS Errors.
framing­errors
Number of failed frames received.
input­giants
Number of frames that are too long.
input­discards
Number of frames in discarding state.
output­collisions
Number of Ethernet collisions.
output­errors
Sum of the outgoing frame aborts and FCS errors.
output­drops
Number of frames dropped.
address­family­name
Name of the address family; must be set to either “inet” or “inet6”.
ifa­destination
Protocol network address of the interface.
ifa­local
Protocol host address on the interface.
ifa­broadcast
Network broadcast address.
Chapter 38: NETCONF
579
580
G8052 Application Guide for ENOS 8.4
Part 8: Monitoring
The ability to monitor traffic passing through the G8052 can be invaluable for troubleshooting some types of networking problems. This sections cover the following monitoring features:
 Remote Monitoring (RMON)
 sFlow
 Port Mirroring
© Copyright Lenovo 2016
581
582
G8052 Application Guide for ENOS 8.4
Chapter 39. Remote Monitoring
Remote Monitoring (RMON) allows network devices to exchange network monitoring data.
RMON allows the switch to perform the following functions:
© Copyright Lenovo 2016

Track events and trigger alarms when a threshold is reached. 
Notify administrators by issuing a syslog message or SNMP trap. 583
RMON Overview
The RMON MIB provides an interface between the RMON agent on the switch and an RMON management application. The RMON MIB is described in RFC 1757. The RMON standard defines objects that are suitable for the management of Ethernet networks. The RMON agent continuously collects statistics and proactively monitors switch performance. RMON allows you to monitor traffic flowing through the switch.
The switch supports the following RMON Groups, as described in RFC 1757:
584

Group 1: Statistics

Group 2: History

Group 3: Alarms

Group 9: Events
G8052 Application Guide for ENOS 8.4
RMON Group 1—Statistics
The switch supports collection of Ethernet statistics as outlined in the RMON statistics MIB, in reference to etherStatsTable. You can configure RMON statistics on a per‐port basis. RMON statistics are sampled every second, and new data overwrites any old data on a given port.
Note: RMON port statistics must be enabled for the port before you can view RMON statistics.
The following is an example of configuring RMON Group 1:
1. Enable RMON on a port. RS G8052(config)# interface port 1
RS G8052(config­if)# rmon
2. View RMON statistics for the port. RS G8052(config­if)# show interface port 1 rmon­counters
­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
RMON statistics for port 1:
etherStatsDropEvents: NA
etherStatsOctets: 7305626
etherStatsPkts: 48686
etherStatsBroadcastPkts: 4380
etherStatsMulticastPkts: 6612
etherStatsCRCAlignErrors: 22
etherStatsUndersizePkts: 0
etherStatsOversizePkts: 0
etherStatsFragments: 2
etherStatsJabbers: 0
etherStatsCollisions: 0
etherStatsPkts64Octets: 27445
etherStatsPkts65to127Octets: 12253
etherStatsPkts128to255Octets: 1046
etherStatsPkts256to511Octets: 619
etherStatsPkts512to1023Octets: 7283
etherStatsPkts1024to1518Octets: 38
© Copyright Lenovo 2016
Chapter 39: Remote Monitoring
585
RMON Group 2—History
The RMON History Group allows you to sample and archive Ethernet statistics for a specific interface during a specific time interval. History sampling is done per port. Note: RMON port statistics must be enabled for the port before an RMON History Group can monitor the port. Data is stored in buckets, which store data gathered during discreet sampling intervals. At each configured interval, the History index takes a sample of the current Ethernet statistics, and places them into a bucket. History data buckets reside in dynamic memory. When the switch is re‐booted, the buckets are emptied. Requested buckets are the number of buckets, or data slots, requested by the user for each History Group. Granted buckets are the number of buckets granted by the system, based on the amount of system memory available. The system grants a maximum of 50 buckets.
You can use an SNMP browser to view History samples.
History MIB Object ID
The type of data that can be sampled must be of an ifIndex object type, as described in RFC 1213 and RFC 1573. The most common data type for the History sample is as follows: 1.3.6.1.2.1.2.2.1.1.<x> The last digit (x) represents the number of the port to monitor.
Configuring RMON History
Perform the following steps to configure RMON History on a port. 1. Enable RMON on a port. RS G8052(config)# interface port 1
RS G8052(config­if)# rmon
RS G8052(config­if)# exit
2. Configure the RMON History parameters for a port. RS
RS
RS
RS
G8052(config)# rmon history 1 interface­oid 1.3.6.1.2.1.2.2.1.1.<x>
G8052(config)# rmon history 1 requested­buckets 30
G8052(config)# rmon history 1 polling­interval 120
G8052(config)# rmon history 1 owner "rmon port 1 history"
where <x> is the number of the port to monitor. For example, the full OID for port 1 would be:
1.3.6.1.2.1.2.2.1.1.1
586
G8052 Application Guide for ENOS 8.4
3. View RMON history for the port. RS G8052(config)# show rmon history
RMON History group configuration:
Index IFOID Interval Rbnum Gbnum
­­­­­ ­­­­­­­­­­­­­­­­­­­­­­­ ­­­­­­­­ ­­­­­ ­­­­­
1 1.3.6.1.2.1.2.2.1.1.1 120 30 30
Index Owner
­­­­­ ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
1 rmon port 1 history
RMON Group 3—Alarms
The RMON Alarm Group allows you to define a set of thresholds used to determine network performance. When a configured threshold is crossed, an alarm is generated. For example, you can configure the switch to issue an alarm if more than 1,000 CRC errors occur during a 10‐minute time interval. Each Alarm index consists of a variable to monitor, a sampling time interval, and parameters for rising and falling thresholds. The Alarm Group can be used to track rising or falling values for a MIB object. The object must be a counter, gauge, integer, or time interval.
Use one of the following commands to correlate an Alarm index to an Event index: RS G8052(config)# rmon alarm <alarm number> rising­crossing­index <event number>
RS G8052(config)# rmon alarm <alarm number> falling­crossing­index <event number>
When the alarm threshold is reached, the corresponding event is triggered. Alarm MIB objects
The most common data types used for alarm monitoring are ifStats: errors, drops, bad CRCs, and so on. These MIB Object Identifiers (OIDs) correlate to the ones tracked by the History Group. An example statistic follows: 1.3.6.1.2.1.5.1.0 – mgmt.icmp.icmpInMsgs
1.3.6.1.2.1.2.2.1.10.x – ifInOctets
The last digit (x) represents the interface on which to monitor, which corresponds to the interface number, or port number, as follows: 1­128 = IF 1­128
129 = port 1
130 = port 2
…
172 = port 44
This value represents the alarm’s MIB OID, as a string. Note that for non‐tables, you must supply a .0 to specify end node.
Configuring RMON Alarms
Follow these examples to configure RMON alarms.
© Copyright Lenovo 2016
Chapter 39: Remote Monitoring
587
RMON Alarm Configuration Example 1
Configure the RMON Alarm parameters to track the number of packets received on port 1. RS
RS
RS
RS
RS
RS
G8052(config)# rmon alarm 1 oid 1.3.6.1.2.1.2.2.1.10.129
G8052(config)# rmon alarm 1 alarm­type rising
G8052(config)# rmon alarm 1 rising­crossing­index 100
G8052(config)# rmon alarm 1 interval 3600
G8052(config)# rmon alarm 1 rising­limit 2000000000
G8052(config)# rmon alarm 1 owner "Alarm for ifInOctets"
This configuration creates an RMON alarm that checks ifInOctets on port 1 once every hour. If the statistic exceeds two billion, an alarm is generated that triggers event index 100.
RMON Alarm Configuration Example 2
Configure the RMON Alarm parameters to track ICMP messages. RS
RS
RS
RS
RS
RS
RS
G8052(config)# rmon alarm 1 oid 1.3.6.1.2.1.5.8.0
G8052(config)# rmon alarm 1 alarm­type rising
G8052(config)# rmon alarm 1 rising­crossing­index 110
G8052(config)# rmon alarm 1 interval­time 60
G8052(config)# rmon alarm 1 rising­limit 200
G8052(config)# rmon alarm 1 sample delta
G8052(config)# rmon alarm 1 owner "Alarm for icmpInEchos"
This configuration creates an RMON alarm that checks icmpInEchos on the switch once every minute. If the statistic exceeds 200 within a 60 second interval, an alarm is generated that triggers event index 110. 588
G8052 Application Guide for ENOS 8.4
RMON Group 9—Events
The RMON Event Group allows you to define events that are triggered by alarms. An event can be a log message, an SNMP trap, or both. When an alarm is generated, it triggers a corresponding event notification. Use the following commands to correlate an Event index to an alarm: RS G8052(config)# rmon alarm <alarm number> rising­crossing­index <event number>
RS G8052(config)# rmon alarm <alarm number> falling­crossing­index <event number>
RMON events use SNMP and syslogs to send notifications. Therefore, an SNMP trap host must be configured for trap event notification to work properly. RMON uses a syslog host to send syslog messages. Therefore, an existing syslog host must be configured for event log notification to work properly. Each log event generates a syslog of type RMON that corresponds to the event. For example, to configure the RMON event parameters. RS G8052(config)# rmon event 110 type log
RS G8052(config)# rmon event 110 description "SYSLOG_this_alarm"
RS G8052(config)# rmon event 110 owner "log icmpInEchos alarm"
This configuration creates an RMON event that sends a syslog message each time it is triggered by an alarm. © Copyright Lenovo 2016
Chapter 39: Remote Monitoring
589
590
G8052 Application Guide for ENOS 8.4
Chapter 40. sFlow
The G8052 supports sFlow technology for monitoring traffic in data networks. The switch includes an embedded sFlow agent which can be configured to provide continuous monitoring information of IPv4 traffic to a central sFlow analyzer.
The switch is responsible only for forwarding sFlow information. A separate sFlow analyzer is required elsewhere on the network to interpret sFlow data.
Note: Lenovo Enterprise Network Operating System 8.4 does not support IPv6 for sFlow.
sFlow Statistical Counters
The G8052 can be configured to send network statistics to an sFlow analyzer at regular intervals. For each port, a polling interval of 5 to 60 seconds can be configured, or 0 (the default) to disable this feature.
When polling is enabled, at the end of each configured polling interval, the G8052 reports general port statistics and port Ethernet statistics.
sFlow Network Sampling
In addition to statistical counters, the G8052 can be configured to collect periodic samples of the traffic data received on each port. For each sample, 128 bytes are copied, UDP‐encapsulated, and sent to the configured sFlow analyzer.
For each port, the sFlow sampling rate can be configured to occur once each 256 to 65536 packets, or 0 to disable (the default). A sampling rate of 256 means that one sample will be taken for approximately every 256 packets received on the port. The sampling rate is statistical, however. It is possible to have slightly more or fewer samples sent to the analyzer for any specific group of packets (especially under low traffic conditions). The actual sample rate becomes most accurate over time, and under higher traffic flow.
sFlow sampling has the following restrictions:

Sample Rate—The fastest sFlow sample rate is 1 out of every 256 packets.

ACLs—sFlow sampling is performed before ACLs are processed. For ports configured both with sFlow sampling and one or more ACLs, sampling will occur regardless of the action of the ACL.

Port Mirroring—sFlow sampling will not occur on mirrored traffic. If sFlow sampling is enabled on a port that is configured as a port monitor, the mirrored traffic will not be sampled.

Egress traffic—sFlow sampling will not occur on egress traffic.
Note: Although sFlow sampling is not generally a CPU‐intensive operation, configuring fast sampling rates (such as once every 256 packets) on ports under heavy traffic loads can cause switch CPU utilization to reach maximum. Use larger rate values for ports that experience heavy traffic.
© Copyright Lenovo 2016
591
sFlow Example Configuration
1. Specify the location of the sFlow analyzer (the server and optional port to which the sFlow information will be sent):
RS G8052(config)# sflow server <IPv4 address>(sFlow server address)
RS G8052(config)# sflow port <service port>(Set the optional service port)
RS G8052(config)# sflow enable
(Enable sFlow features)
By default, the switch uses established sFlow service port 6343.
To disable sFlow features across all ports, use the no sflow enable command.
2. On a per‐port basis, define the statistics polling rate:
RS G8052(config)# interface port <port>
RS G8052(config­if)# sflow polling <polling rate>(Statistics polling rate)
Specify a polling rate between 5 and 60 seconds, or 0 to disable. By default, polling is 0 (disabled) for each port.
3. On a per‐port basis, define the data sampling rate:
RS G8052(config­if)# sflow sampling <sampling rate>(Data sampling rate)
Specify a sampling rate between 256 and 65536 packets, or 0 to disable. By default, the sampling rate is 0 (disabled) for each port.
4. Save the configuration.
592
G8052 Application Guide for ENOS 8.4
Chapter 41. Port Mirroring
The Lenovo Enterprise Network Operating System port mirroring feature allows you to mirror (copy) the packets of a target port, and forward them to a monitoring port. Port mirroring functions for all layer 2 and layer 3 traffic on a port. This feature can be used as a troubleshooting tool or to enhance the security of your network. For example, an IDS server or other traffic sniffer device or analyzer can be connected to the monitoring port to detect intruders attacking the network.
© Copyright Lenovo 2016
593
Port Mirroring Model
The G8052 supports a “many to one” mirroring model. As shown in Figure 52, selected traffic for ports 1 and 2 is being monitored by port 3. In the example, both ingress traffic and egress traffic on port 2 are copied and forwarded to the monitor. However, port 1 mirroring is configured so that only ingress traffic is copied and forwarded to the monitor. A device attached to port 3 can analyze the resulting mirrored traffic.
Figure 52. Mirroring Ports
Mirrored Ports
Monitor Port
Ingress
Both
Traffic
Connected to
sniffer device
1
2
3
4
Specified traffic is copied
and forwarded to Monitor Port
The G8052 supports four monitor ports. Each monitor port can receive mirrored traffic from any number of target ports.
Enterprise NOS does not support “one to many” or “many to many” mirroring models where traffic from a specific port traffic is copied to multiple monitor ports. For example, port 1 traffic cannot be monitored by both port 3 and 4 at the same time, nor can port 2 ingress traffic be monitored by a different port than its egress traffic.
Ingress and egress traffic is duplicated and sent to the monitor port after processing.
594
G8052 Application Guide for ENOS 8.4
Configuring Port Mirroring
The following procedure may be used to configure port mirroring for the example shown in Figure 52 on page 594:
1. Specify the monitoring port, the mirroring port(s), and the port‐mirror direction. RS G8052(config)# port­mirroring monitor­port 3 mirroring­port 1 in
RS G8052(config)# port­mirroring monitor­port 3 mirroring­port 2 both
2. Enable port mirroring. RS G8052(config)# port­mirroring enable
3. View the current configuration.
RS G8052# show port­mirroring Port Monitoring : Enabled
Monitoring Ports
© Copyright Lenovo 2016
Mirrored Ports
3
1, in
2, both
Chapter 41: Port Mirroring
595
596
G8052 Application Guide for ENOS 8.4
Part 9: Appendices
 Getting help and technical assistance
 Notices
© Copyright Lenovo 2016
597
598
G8052 Application Guide for ENOS 8.4
Appendix A. Glossary
CNA
Converged Network Adapter. A device used for I/O consolidation such as that in Converged Enhanced Ethernet (CEE) environments implementing Fibre Channel over Ethernet (FCoE). The CNA performs the duties of both a Network Interface Card (NIC) for Local Area Networks (LANs) and a Host Bus Adapter (HBA) for Storage Area Networks (SANs).
DIP
The destination IP address of a frame.
Dport
The destination port (application socket: for example, http‐80/https‐443/DNS‐53)
HBA
Host Bus Adapter. An adapter or card that interfaces with device drivers in the host operating system and the storage target in a Storage Area Network (SAN). It is equivalent to a Network Interface Controller (NIC) from a Local Area Network (LAN).
NAT
Network Address Translation. Any time an IP address is changed from one source IP or destination IP address to another address, network address translation can be said to have taken place. In general, half NAT is when the destination IP or source IP address is changed from one address to another. Full NAT is when both addresses are changed from one address to another. No NAT is when neither source nor destination IP addresses are translated. Preemption
In VRRP, preemption will cause a Virtual Router that has a lower priority to go into backup if a peer Virtual Router starts advertising with a higher priority.
Priority
In VRRP, the value given to a Virtual Router to determine its ranking with its peer(s). Minimum value is 1 and maximum value is 254. Default is 100. A higher number will win out for master designation.
Proto (Protocol)
The protocol of a frame. Can be any value represented by a 8‐bit value in the IP header adherent to the IP specification (for example, TCP, UDP, OSPF, ICMP, and so on.)
SIP
The source IP address of a frame.
SPort
The source port (application socket: for example, HTTP‐80/HTTPS‐443/DNS‐53).
Tracking
In VRRP, a method to increase the priority of a virtual router and thus master designation (with preemption enabled). Tracking can be very valuable in an active/active configuration.
You can track the following:
Active IP interfaces on the Web switch (increments priority by 2 for each)
Active ports on the same VLAN (increments priority by 2 for each)
 Number of virtual routers in master mode on the switch


VIR
Virtual Interface Router. A VRRP address is an IP interface address shared between two or more virtual routers.
Virtual Router
A shared address between two devices utilizing VRRP, as defined in RFC 2338. One virtual router is associated with an IP interface. This is one of the IP interfaces that the switch is assigned. All IP interfaces on the G8052s must be in a VLAN. If there is more than one VLAN defined on the Web switch, then the VRRP broadcasts will only be sent out on the VLAN of which the associated IP interface is a member.
© Copyright Lenovo 2016
599
VRID
Virtual Router Identifier. In VRRP, a numeric ID is used by each virtual router to create its MAC address and identify its peer for which it is sharing this VRRP address. The VRRP MAC address as defined in the RFC is 00‐00‐5E‐00‐01‐<VRID>.
If you have a VRRP address that two switches are sharing, then the VRID number needs to be identical on both switches so each virtual router on each switch knows with whom to share.
VRRP
Virtual Router Redundancy Protocol. A protocol that acts very similarly to Ciscoʹs proprietary HSRP address sharing protocol. The reason for both of these protocols is so devices have a next hop or default gateway that is always available. Two or more devices sharing an IP interface are either advertising or listening for advertisements. These advertisements are sent via a broadcast message to an address such as 224.0.0.18.
With VRRP, one switch is considered the master and the other the backup. The master is always advertising via the broadcasts. The backup switch is always listening for the broadcasts. If the master stops advertising, the backup will take over ownership of the VRRP IP and MAC addresses as defined by the specification. The switch announces this change in ownership to the devices around it by way of a Gratuitous ARP, and advertisements. If the backup switch didnʹt do the Gratuitous ARP the Layer 2 devices attached to the switch would not know that the MAC address had moved in the network. For a more detailed description, refer to RFC 2338.
600
G8052 Application Guide for ENOS 8.4
Appendix B. Getting help and technical assistance
If you need help, service, or technical assistance or just want more information about Lenovo products, you will find a wide variety of sources available from Lenovo to assist you.
Use this information to obtain additional information about Lenovo and Lenovo products, and determine what to do if you experience a problem with your Lenovo system or optional device.
Note: This section includes references to IBM web sites and information about obtaining service. IBM is Lenovoʹs preferred service provider for the System x, Flex System, and NeXtScale System products.
Before you call, make sure that you have taken these steps to try to solve the problem yourself.
If you believe that you require warranty service for your Lenovo product, the service technicians will be able to assist you more efficiently if you prepare before you call.
© Copyright Lenovo 2016

Check all cables to make sure that they are connected.

Check the power switches to make sure that the system and any optional devices are turned on.

Check for updated software, firmware, and operating‐system device drivers for your Lenovo product. The Lenovo Warranty terms and conditions state that you, the owner of the Lenovo product, are responsible for maintaining and updating all software and firmware for the product (unless it is covered by an additional maintenance contract). Your service technician will request that you upgrade your software and firmware if the problem has a documented solution within a software upgrade.

If you have installed new hardware or software in your environment, check the IBM ServerProven website to make sure that the hardware and software is supported by your product.

Go to the IBM Support portal to check for information to help you solve the problem.

Gather the following information to provide to the service technician. This data will help the service technician quickly provide a solution to your problem and ensure that you receive the level of service for which you might have contracted.

Hardware and Software Maintenance agreement contract numbers, if applicable

Machine type number (if applicable–Lenovo 4‐digit machine identifier)

Model number

Serial number

Current system UEFI and firmware levels

Other pertinent information such as error messages and logs
601

Start the process of determining a solution to your problem by making the pertinent information available to the service technicians. The IBM service technicians can start working on your solution as soon as you have completed and submitted an Electronic Service Request.
You can solve many problems without outside assistance by following the troubleshooting procedures that Lenovo provides in the online help or in the Lenovo product documentation. The Lenovo product documentation also describes the diagnostic tests that you can perform. The documentation for most systems, operating systems, and programs contains troubleshooting procedures and explanations of error messages and error codes. If you suspect a software problem, see the documentation for the operating system or program.
602
G8052 Application Guide for ENOS 8.4
Appendix C. Notices
Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead. However, it is the userʹs responsibility to evaluate and verify the operation of any other product, program, or service.
Lenovo may have patents or pending patent applications covering subject matter described in this document. The furnishing of this document does not give you any license to these patents. You can send license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place ‐ Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON‐INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice.
The products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. The information contained in this document does not affect or change Lenovo product specifications or warranties.
Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties. All information contained in this document was obtained in specific environments and is presented as an illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you.
Any references in this publication to non‐Lenovo Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the materials for this Lenovo product, and use of those Web sites is at your own risk.
© Copyright Lenovo 2016
603
Any performance data contained herein was determined in a controlled environment. Therefore, the result obtained in other operating environments may vary significantly. Some measurements may have been made on development‐level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.
604
G8052 Application Guide for ENOS 8.4
Trademarks
Lenovo, the Lenovo logo, Flex System, System x, NeXtScale System, and X‐Architecture are trademarks of Lenovo in the United States, other countries, or both.
Intel and Intel Xeon are trademarks of Intel Corporation in the United States, other countries, or both.
Internet Explorer, Microsoft, and Windows are trademarks of the Microsoft group of companies.
Linux is a registered trademark of Linus Torvalds.
Other company, product, or service names may be trademarks or service marks of others.
© Copyright Lenovo 2016
Appendix C: Notices
605
Important Notes
Processor speed indicates the internal clock speed of the microprocessor; other factors also affect application performance.
CD or DVD drive speed is the variable read rate. Actual speeds vary and are often less than the possible maximum.
When referring to processor storage, real and virtual storage, or channel volume, KB stands for 1 024 bytes, MB stands for 1 048 576 bytes, and GB stands for 1 073 741 824 bytes.
When referring to hard disk drive capacity or communications volume, MB stands for 1 000 000 bytes, and GB stands for 1 000 000 000 bytes. Total user‐accessible capacity can vary depending on operating environments.
Maximum internal hard disk drive capacities assume the replacement of any standard hard disk drives and population of all hard‐disk‐drive bays with the largest currently supported drives that are available from Lenovo.
Maximum memory might require replacement of the standard memory with an optional memory module.
Each solid‐state memory cell has an intrinsic, finite number of write cycles that the cell can incur. Therefore, a solid‐state device has a maximum number of write cycles that it can be subjected to, expressed as total bytes written (TBW). A device that has exceeded this limit might fail to respond to system‐generated commands or might be incapable of being written to. Lenovo is not responsible for replacement of a device that has exceeded its maximum guaranteed number of program/erase cycles, as documented in the Official Published Specifications for the device.
Lenovo makes no representations or warranties with respect to non‐Lenovo products. Support (if any) for the non‐Lenovo products is provided by the third party, not Lenovo.
Some software might differ from its retail version (if available) and might not include user manuals or all program functionality.
606
G8052 Application Guide for ENOS 8.4
Recycling Information
Lenovo encourages owners of information technology (IT) equipment to responsibly recycle their equipment when it is no longer needed. Lenovo offers a variety of programs and services to assist equipment owners in recycling their IT products. For information on recycling Lenovo products, go to:
http://www.lenovo.com/recycling © Copyright Lenovo 2016
Appendix C: Notices
607
Particulate Contamination
Attention: Airborne particulates (including metal flakes or particles) and reactive gases acting alone or in combination with other environmental factors such as humidity or temperature might pose a risk to the device that is described in this document.
Risks that are posed by the presence of excessive particulate levels or concentrations of harmful gases include damage that might cause the device to malfunction or cease functioning altogether. This specification sets forth limits for particulates and gases that are intended to avoid such damage. The limits must not be viewed or used as definitive limits, because numerous other factors, such as temperature or moisture content of the air, can influence the impact of particulates or environmental corrosives and gaseous contaminant transfer. In the absence of specific limits that are set forth in this document, you must implement practices that maintain particulate and gas levels that are consistent with the protection of human health and safety. If Lenovo determines that the levels of particulates or gases in your environment have caused damage to the device, Lenovo may condition provision of repair or replacement of devices or parts on implementation of appropriate remedial measures to mitigate such environmental contamination. Implementation of such remedial measures is a customer responsibility..
Contaminant
Limits
Particulate
• The room air must be continuously filtered with 40% atmospheric dust spot efficiency (MERV 9) according to ASHRAE Standard 52.21.
• Air that enters a data center must be filtered to 99.97% efficiency or greater, using high‐efficiency particulate air (HEPA) filters that meet MIL‐STD‐282.
• The deliquescent relative humidity of the particulate contamination must be more than 60%2.
• The room must be free of conductive contamination such as zinc whis‐
kers.
Gaseous
• Copper: Class G1 as per ANSI/ISA 71.04‐19853
• Silver: Corrosion rate of less than 300 Å in 30 days
1 ASHRAE 52.2‐2008 ‐ Method of Testing General Ventilation Air‐Cleaning Devices for Removal Efficiency by Particle Size. Atlanta: American Society of Heating, Refrigerating and Air‐Con‐
ditioning Engineers, Inc.
2 The deliquescent relative humidity of particulate contamination is the relative humidity at which the dust absorbs enough water to become wet and promote ionic conduction.
3 ANSI/ISA‐71.04‐1985. Environmental conditions for process measurement and control systems: Airborne contaminants. Instrument Society of America, Research Triangle Park, North Car‐
olina, U.S.A.
608
G8052 Application Guide for ENOS 8.4
Telecommunication Regulatory Statement
This product may not be certified in your country for connection by any means whatsoever to interfaces of public telecommunications networks. Further certification may be required by law prior to making any such connection. Contact a Lenovo representative or reseller for any questions.
© Copyright Lenovo 2016
Appendix C: Notices
609
Electronic Emission Notices
When you attach a monitor to the equipment, you must use the designated monitor cable and any interference suppression devices that are supplied with the monitor.
Federal Communications Commission (FCC) Statement
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
Properly shielded and grounded cables and connectors must be used to meet FCC emission limits. Lenovo is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that might cause undesired operation.
Industry Canada Class A Emission Compliance Statement
This Class A digital apparatus complies with Canadian ICES‐003.
Avis de Conformité à la Réglementation d'Industrie Canada
Cet appareil numérique de la classe A est conforme à la norme NMB‐003 du Canada.
Australia and New Zealand Class A Statement
Attention: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
European Union - Compliance to the Electromagnetic Compatibility
Directive
This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC (until April 19, 2016) and EU Council Directive 2014/30/EU (from April 20, 2016) on the approximation of the laws of the Member States relating to electromagnetic compatibility. Lenovo cannot accept responsibility for 610
G8052 Application Guide for ENOS 8.4
any failure to satisfy the protection requirements resulting from a non‐recommended modification of the product, including the installation of option cards from other manufacturers.
This product has been tested and found to comply with the limits for Class A equipment according to European Standards harmonized in the Directives in compliance. The limits for Class A equipment were derived for commercial and industrial environments to provide reasonable protection against interference with licensed communication equipment.
Lenovo, Einsteinova 21, 851 01 Bratislava, Slovakia Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Germany Class A Compliance Statement
Deutschsprachiger EU Hinweis:
Hinweis für Geräte der Klasse A EU‐Richtlinie zur Elektromagnetischen Verträglichkeit
Dieses Produkt entspricht den Schutzanforderungen der EU‐Richtlinie 2014/30/EU (früher 2004/108/EC) zur Angleichung der Rechtsvorschriften über die elektromagnetische Verträglichkeit in den EU‐Mitgliedsstaaten und hält die Grenzwerte der Klasse A der Norm gemäß Richtlinie.
Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu installieren und zu betreiben. Des Weiteren dürfen auch nur von der Lenovo empfohlene Kabel angeschlossen werden. Lenovo übernimmt keine Verantwortung für die Einhaltung der Schutzanforderungen, wenn das Produkt ohne Zustimmung der Lenovo verändert bzw. wenn Erweiterungskomponenten von Fremdherstellern ohne Empfehlung der Lenovo gesteckt/eingebaut werden.
Deutschland:
Einhaltung des Gesetzes über die elektromagnetische Verträglichkeit von Betriebsmittein
Dieses Produkt entspricht dem ʺGesetz über die elektromagnetische Verträglichkeit von Betriebsmittelnʺ EMVG (früher ʺGesetz über die elektromagnetische Verträglichkeit von Gerätenʺ). Dies ist die Umsetzung der EU‐Richtlinie 2014/30/EU (früher 2004/108/EC) in der Bundesrepublik Deutschland.
Zulassungsbescheinigung laut dem Deutschen Gesetz über die elektromagnetische Verträglichkeit von Betriebsmitteln, EMVG vom 20. Juli 2007 (früher Gesetz über die elektromagnetische Verträglichkeit von Geräten), bzw. der EMV EU Richtlinie 2014/30/EU (früher 2004/108/EC ), für Geräte der Klasse A.
© Copyright Lenovo 2016
Appendix C: Notices
611
Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das EG‐Konformitätszeichen ‐ CE ‐ zu führen. Verantwortlich für die Konformitätserklärung nach Paragraf 5 des EMVG ist die Lenovo (Deutschland) GmbH, Meitnerstr. 9, D‐70563 Stuttgart.
Informationen in Hinsicht EMVG Paragraf 4 Abs. (1) 4:
Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse A.
Nach der EN 55022: ʺDies ist eine Einrichtung der Klasse A. Diese Einrichtung kann im Wohnbereich Funkstörungen verursachen; in diesem Fall kann vom Betreiber verlangt werden, angemessene Maßnahmen durchzuführen und dafür aufzukommen.ʺ
Nach dem EMVG: ʺGeräte dürfen an Orten, für die sie nicht ausreichend entstört sind, nur mit besonderer Genehmigung des Bundesministers für Post und Telekommunikation oder des Bundesamtes für Post und Telekommunikation betrieben werden. Die Genehmigung wird erteilt, wenn keine elektromagnetischen Störungen zu erwarten sind.ʺ (Auszug aus dem EMVG, Paragraph 3, Abs. 4). Dieses Genehmigungsverfahrenist nach Paragraph 9 EMVG in Verbindung mit der entsprechenden Kostenverordnung (Amtsblatt 14/93) kostenpflichtig.
Anmerkung: Um die Einhaltung des EMVG sicherzustellen sind die Geräte, wie in den Handbüchern angegeben, zu installieren und zu betreiben.
Japan VCCI Class A Statement
This is a Class A product based on the standard of the Voluntary Control Council for Interference (VCCI). If this equipment is used in a domestic environment, radio interference may occur, in which case the user may be required to take corrective actions.
Japan Electronics and Information Technology Industries Association
(JEITA) Statement
Japan Electronics and Information Technology Industries Association (JEITA) Confirmed Harmonics Guidelines (products less than or equal to 20 A per phase)
Japan Electronics and Information Technology Industries Association (JEITA) Confirmed Harmonics Guidelines with Modifications (products greater than 20 A per phase).
612
G8052 Application Guide for ENOS 8.4
Korea Communications Commission (KCC) Statement
This is electromagnetic wave compatibility equipment for business (Type A). Sellers and users need to pay attention to it. This is for any areas other than home.
© Copyright Lenovo 2016
Appendix C: Notices
613
Russia Electromagnetic Interference (EMI) Class A statement
614
G8052 Application Guide for ENOS 8.4
People’s Republic of China Class A electronic emission
statement
© Copyright Lenovo 2016
Appendix C: Notices
615
Taiwan Class A compliance statement
616
G8052 Application Guide for ENOS 8.4