Download Activities

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Optical rectenna wikipedia , lookup

Opto-isolator wikipedia , lookup

Transcript
1
1. Activities: Metal Oxide Thin Film Synthesis and Characterization with Index Matching
Application for Light Emitting Diodes
REU Student: Daniel Birdsell
Graduate Mentor: Louis Tribby
Faculty Mentor: Dr. Sang Han
1.A. Introduction
Light Emitting Diodes (LEDs) turn on to full brightness instantly, use less power and last
longer than traditional light bulbs, and will save money for a typical consumer1. The list of
benefits is long, but there is still room for improvement. In particular, only a very small portion
of the photons (i.e. light) that are generated within an LED actually escape the device to
illuminate the surroundings. This report investigates a way to increase light extraction from
LEDs by depositing thin films of metal oxides on top of LED devices. The index of refraction of
these films is similar to that of the LED, causing a larger portion of the light to be extracted via
index matching.
This report describes the work that was done during the 2012-2013 academic year. It
includes the deposition of metal oxide thin films, the investigation of film properties (thickness
and morphology) and the feasibility of their use in increasing LED efficiency. It consists of
two separate sections that focus on the activities and the findings. Within the activities section of
the report, a background is provided to give general information about thin film synthesis and
light extraction, which is followed by the research objectives, and finally the methodology and a
description of the experiments. The findings section of the report contains a results section that
characterizes morphology, chemical composition, and film thickness. This is followed by major
conclusions and future work.
1.B. Background
Light emitting diodes are frequently used as light sources in electronics, liquid crystal
displays, and vehicles, and they can be used as monochromatic light sensors2. They emit photons
when a forward potential is applied to a p-n junction, causing electrons to move from the
conduction band of the n-type semiconductor to the valence band of the p-type semiconductor.
LEDs consume less power incandescent light bulbs because they are highly efficient at
converting light into photons (80 - 90% efficient)3. But many of the photons are internally
reflected, never to be seen externally as light, due to the high index of refraction of the LED
material. Photonic efficiency, the ratio of photons emitted to photons generated, is only 2-10%3.
A number of techniques are currently used to increase photonic efficiency.
Nanostructures can be introduced at the interface that locally change the index of refraction
and/or increase the chance of light hitting the interface at an angle that will escape the LED.
Examples of this technique include the TiO2 nano-pillars that were created by Yoon et al.2 with a
sol-imprinting process and the aluminum-doped ZnO photonic crystals that were created by
Yang et al.4 (shown in figure 1a and 1b). Another technique is to change the geometry of the
polymer casing that houses the LED. This increases the chance of light impinging on the
casing/air interface at a favorable angle in the same way that the nanostructures improve at the
LED material/casing interface. The polymer casing serves two purposes: it securely holds the
2
LED and all of its wiring, and it has an index of refraction in between that of the LED material
and that of air, which increases light extraction (more detail later). A commercial LED with its
casing is shown in Figure 1(c).
Figure 1: (a) Atomic force microscopy (AFM) image of TiO2 nano-pillars to locally change index of
refraction2; (b) cross sectional view of LED device with Al-doped ZnO photonic crystals and an AFM
image of the photonic crystals4;
(c) An image of a polymer case used in LEDs5. Note the casing is rounded to increase the proportion of
light hitting at a steep angle.
Another technique to increase light extraction is called index matching. As shown in
Figure 2, light bends at the interface of two materials having different indices of refraction.
When moving from high index of refraction materials to low index of refraction materials, some
of the light is internally reflected. If the difference in indices of refraction is larger, more light is
internally reflected. This light-bending phenomena is described mathematically with Snell's Law
in the equation below. Using Snell's Law, the critical angle (θc), or the smallest angle at which
light can reach the interface to be internally reflected, can be calculated. To increase light
extraction from LEDs, the critical angle must be diminished by decreasing the differences
between indices of refraction at the interface. This "matching of indices of refraction is where
the term "index matching comes from."
3
Figure 2: (a) Illustrations of Snell's law1 and (b) how index matching can increase LED light extraction
by decreasing the critical angle. When light hits the interface between air and the LED at an angle greater
than the critical angle it will be internally reflected. In the lower LED setup, a thin film with an
intermediate index of refraction allows light that hits the interface at the old θc to escape the LED
material.
Thin films, chosen for their index of refraction, could be synthesized on top of LEDs to
enhance light extraction via index matching. This is illustrated in Figure 2b where light is
internally reflected at θc in the top setup but is allowed to escape the LED material after a thin
film is placed on the LED in the bottom setup. In theory, this index matching can be extended to
multiple thin film layers, each with a slightly smaller index of refraction. Table 1 shows the
index of refraction of the species that are commonly used in LEDs, the index of refraction of
some of the metal oxides that are synthesized in this study, and the index of refraction of air. A
three layer index matching device could consist of ZnO on Anatase on Rutile on a GaP LED.
For a photon to escape this LED, it would not need to escape from GaP (n=3.18) straight to Air
(n=1.00). Instead, the photon would go through several materials that slowly ramp down the
indices of refraction that the photon must pass through (index of refractions in order are 3.18,
2.75, 2.5, 2.0, and 1.0).
4
Table 1 - Index of Refraction of Species in LED Systems
Purpose
Air
Film
Film
Film
LED
LED
LED
LED
Species
Air
ZnO
TiO2
(Anatase)
TiO2 (Rutile)
GaN
GaP
AlGaInP
ZnSe
Refractive
Index (n)
1.0
2.0
2.5
2.75
2.4
3.18
3.23
2.52
Thin films are defined to be less than several micrometers thick. These films can be
deposited using a variety of different techniques. The deposition techniques include dip-coating,
spin coating, chemical vapor deposition, electrodeposition, electroless deposition, and atomic
layer deposition. In this study, TiO2 is deposited via electrodeposition, and ZnO is deposited
with both electrodeposition and dip coating.
In electrodeposition, a solid is deposited onto an electrode from an ionic solution. A
three electrode setup is used in this study. A potential is applied to the working electrode that
sits in an ionic solution. The ions react with and deposit onto the working electrode, forming a
film. The auxiliary electrode is there to complete the circuit, and the reference electrode gives a
reference potential that is being applied. Electrodeposition generally produces more uniform
films than dip coating. Figure 3 shows a three electrode setup in which zinc oxide is deposited
onto the working electrode.
In dip coating, a substrate is lowered into a solution and then very slowly pulled out of
solution. Species within the solution are deposited onto the substrate as the solution dries. Dip
coating is advantageous for its simplicity, but the film quality is less than that of
electrodeposition. In this case, high film quality means that the film covers the entire substrate
(i.e. no pores reaching to the substrate) and that the morphology is smooth.
5
Figure 3: A schematic of a three electrode electrodeposition of ZnO with a chemical formula for aqueous
zinc ions reacting to zinc oxide solid on the working electrode. This reaction requires electrons to be
passed through the system in what amounts to be an electrical circuit.
Of the many characterization techniques that are used in this study, spectroscopic
ellipsometry is the most relevant to the investigation. This optical technique provides film
thickness and its optical properties, such as complex refractive index. First, polarized light is
incident on a film, and the change in intensity and polarization angle for the reflected light is
measured. Then, a model is constructed that takes initial guess values for film optical properties
and thickness (e.g. if a TiO2 film is being studied, the optical properties of TiO2 are input). From
these initial input values, the model prediction is compared to the change in polarization data,
and the sum of the error is minimized by changing the modeled film thickness, optical
parameters, or both. Ellipsometry is a very powerful tool to measure film thickness and optical
parameters, but the results can only be accepted if the model is believed to be true. Figure 4 has
figures that explain polarization and ellipsometry.
6
Figure 4: (a) Electromagnetic radiation (i.e. light) that is elliptically polarized because the two waves are
neither in phase nor 90 degrees out of phase; (b) a schematic of how light interacts with films. Light may
reflect off of the film, enter and penetrate, reflect amongst the internal layers, or any combination of these
behaviors. The change in polarization that is measured in ellipsometry must account for all of these
possible behaviors6.
1.C. Research Objectives
The research objectives of this project are threefold: Firstly, to optimize the synthesis of
metal oxide thin films of ZnO and TiO2. Secondly, to investigate film properties including
thickness, morphology and optical parameters, all of which can affect the optics and electronics
of LEDs and other electronics that utilize thin films. Thirdly, to consider the feasibility of
increasing photonic efficiency through index matching using what has been learned about the
film synthesis and properties.
1.D. Methodology
Films are synthesized using dip coating and electrodeposition. The experimental setups
are shown in Figure 5. ZnO films are created by dip coating and electrodeposition; TiO2 is only
deposited via electrodeposition.
In dip coating, three preliminary solutions are used in the creation of the final dip coating
sol. The first is a hexadecyltrimethylammonium bromide (CTAB) solution consisting of 0.520 g.
of CTAB, 2 mL of ethanol, and 1 mL of CHCl3. The second is an sodium dodecyl sulfate (SDS)
solution consisting of 0.520 g. SDS, 4 mL of methanol, and 1 mL of CHCl3. The SDS solution
is heated and placed in a sonicator to ensure that no species precipitate out. The third solution is
85% ethanol and 15% de-ionized water by volume. These three preliminary solutions are
combined to make a solution called Sol A. Sol A is composed of 0.65 mL of CTAB preliminary
solution, 0.35 mL of SDS preliminary solution, and 1.733 g (approximately 2 mL) of
ethanol/water solution. 0.179 g. zinc nitrate is added to Sol A, which results in a colorless,
transparent precursor solution. Finally, the zinc precursor solution is diluted with the 85%
ethanol and 15% de-ionized water preliminary solution to 1:4 and 1:20 ratios.
To dip coat, a 1 cm x 3 cm silicon substrate is cleaned with piranha solution (consisting
of sulfuric acid and hydrogen peroxide). It is then dipped into solution and removed at an
upward rate of 70 um/sec.
7
Figure 5: These photographs show the process of (a) dip coating and (b) electrodeposition.
In electrodeposition, a three-electrode setup is used with either copper or highly-doped
silicon as the working electrode (which gets deposited onto). The counter electrode is a platinum
mesh, which is not deposited onto but completes the circuit. The reference electrode is Ag/AgCl,
and provides a reference voltage so that the deposition voltage is known. Depositions are done
in the voltage range of -0.30 to -1.40 V with time durations in the range of 3-35 min.
The precursor solution for zinc oxide electrodeposition consists of 10 mM phosphate
buffer (KH2PO4), 10 mM zinc nitrate hexa hydrate (ZnNO3*(H2O)6), and 10 mM potassium
nitrate (KNO3) in a water solvent. The precursor for the TiO2 electrodeposition consists of 10
mM Titanium tetrachloride (TiCl4) and 10 mM hydrogen peroxide (H2O2). The solvent consists
of ethanol and water in a 3:1 ratio.
Characterization is done with Scanning electron microscope (SEM), Energy-dispersive
X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD),
Transmission electron microscopy (TEM), and spectroscopic ellipsometry. SEM is used for
morphological images and side views to get an estimate of the film thickness. This film
thickness estimate is used as an initial guess for film thickness in the ellipsometry model. EDX,
XPS, and XRD are used to confirm that we deposit the species that we expect to. The
ellipsometry setup is shown in Figure 6.
8
Figure 6: Ellipsometer setup with silicon wafer. The polarized light enters from the right, and is
analyzed on the left. The silicon is used in the calibration process before samples are studied.
1.E. Description of Experiments
1.E.a Dip Coating
Dip coating was the first set of experiments that was run. The solutions are described in
the Methodology section. ZnO films were formed onto silicon substrates with dip coating at
both 1:4 and 1:20 solution dilutions.
1.E.b Electrodeposition
After the electrodeposition setup was built, zinc oxide was first deposited on copper, then
onto doped silicon, and finally onto doped silicon with a layer of gold on the back side. Voltages
ranged from -0.30 to -1.40 V, and times ranged from 3 to 35 min depositions. The list of
depositions are shown in Table 2 below. Copper was first deposited onto because it is good at
passing current, and therefore is easy to use in electrodepositon. Doped silicon was deposited
onto next because it is a semiconductor and therefore more closely resembles how
electrodeposition would occur onto LED materials. Gold-coated silicon was used to increase the
current through a silicon wafer, which increases the deposition thickness and improved the film
homogeneity.
Titanium dioxide was deposited at -1.00 V and -1.40 V for 30 min time periods onto
gold-coated silicon. The Titanium tetrachloride precursor is very volatile due to its low vapor
pressure, which makes for difficult solution preparation.
9
Table 2 - ZnO Electrodepositions
ZnO on Copper
ZnO on doped Silicon
ZnO on gold-coated Silicon
Deposition Potential
Run Time (min)
(V)
1
3
-0.3
2
3
-1
3
1
-1
4
10
-1
5
3
-1
Deposition Potential
Run Time (min)
(V)
1
30
-0.3
2
10
-0.3
3
3
-0.3
4
15
-0.3
5
3
-1
6
10
-1
7
35
-1
Deposition Potential
Run Time (min)
(V)
1
30
-1
2
10
-1
3
30
-1.4
4
10
-1.4
5
3
-1.4
10
1.F. References
1.
2.
3.
4.
5.
Pogue, D., New Reasons to Change Light Bulbs. New York Times March 21, 2013, 2013, p
B1.
Yoon, K. M.; Yang, K. Y.; Byeon, K. J.; Lee, H., Enhancement of light extraction in GaN
based LED structures using TiO2 nano-structures. Solid-State Electronics 2010,
54, (4), 484-487.
Benisty, H.; De Neve, H.; Weisbuch, C., Impact of planar microcavity effects on light
extraction - Part I: Basic concepts and analytical trends. Ieee Journal of Quantum
Electronics 1998, 34, (9), 1612-1631.
Yang, W. F.; Liu, Z. G.; Xie, Y. N.; Cai, J. F.; Liu, S.; Gong, H.; Wu, Z. Y., Improvement of
GaN light-emitting diodes with surface-treated Al-doped ZnO transparent Ohmic
contacts by holographic photonic crystal. Applied Physics a-Materials Science &
Processing 107, (4), 809-812.
How Light Emmiting Diodes Work. http://www.howstuffworks.com/led.htm (Nov 1,
2012),