* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Problem 7.14
Surge protector wikipedia , lookup
Power MOSFET wikipedia , lookup
Nanofluidic circuitry wikipedia , lookup
Integrated circuit wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Regenerative circuit wikipedia , lookup
Index of electronics articles wikipedia , lookup
Valve RF amplifier wikipedia , lookup
Opto-isolator wikipedia , lookup
Galvanometer wikipedia , lookup
Operational amplifier wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Charlieplexing wikipedia , lookup
Wilson current mirror wikipedia , lookup
Zobel network wikipedia , lookup
Two-port network wikipedia , lookup
Rectiverter wikipedia , lookup
Electrical ballast wikipedia , lookup
Current mirror wikipedia , lookup
Current source wikipedia , lookup
RLC circuit wikipedia , lookup
Problem 7.14 The switch in the above circuit has been closed for along time before opening at t = 0. Part A Find iL(t) at t > = 0 Solutions: We first find iL at t < 0. When t < 0, we model the inductor as a short circuit and solve for the current using standard circuit analysis techniques. Note that at t < 0, the switch is also a short circuit. Using nodal analysis and assuming all currents flow left to right or top down (except for i which flows as shown in the above diagram). Δ At node A: (-‐120-‐Va)/40 = Va/60 + (Va – Vb)/6 At node B: By observation, Vb = 0V At node C: By observation: Vc = 0-‐20 i = -‐20 i Δ Δ By observation: -‐Vc/60 = i The only possible solution for i is i = 0. And therefore Vc = 0 too. We can now solve for Va: (-‐120 – Va)/40 = Va/60 + Va/6 -‐720-‐6Va = 4Va + 40Va -‐720 = 50Va Va = -‐14.4 V From previous results, the only current flowing through the inductor at t < 0 is the current flowing through the 6 Ohm resistor (the current i is zero and the current through the 100 ohm resistor is Vc/100 = 0. Therefore, by KCL iL = i + i (100 ohm resistor) + i (6 Ohm resistor) = i (6 ohm resistor). Thus, at t < 0, the current through the inductor is Va/6 = -‐2.4A At t = 0+, the current must be the same as at t = 0-‐, so iL = -‐2.4A As t approaches infinity, the inductor once again becomes a short circuit: Δ Δ Δ Δ Δ By observation, at t = infinity, the current through the inductor is 0A. Now, we need to find the time constant of the circuit. Because of the dependent source, we can’t just simply assume it is L/R, so we return to KVL to find the time constant: Using KVL: vL – 20 iΔ + iL (37.5) = 0 (100 and 60 ohm resistors were combined in parallel). By observation iΔ = iL(37.5)/60 = 0.625 iL Substituting into our KVL equation: LdiL/dt – 20 (0.625 iL) + iL (37.5) = 0 From here, we can see the time constant of this circuit is going to be: L/(-‐20(0.625) + 37.5) = 10 ms Thus, the current through the inductor as a function of time is: iL (t) = (final value) + (initial – final) exp (-‐t/6.67msec) iL (t) = 0 + (-‐2.4 – 0) exp (-‐150t) = -‐2.4 exp (-‐100t) where t is in seconds or iL (t) = -‐2.4 exp (-‐0.1t) where t is in milliseconds Part B: Find vL(t) for t > 0 vL(t) = LdiL/dt = 0.250 d/dt (-‐2.4 exp (-‐100t)) vL(t) =60 exp (-‐100t) where t is in seconds or vL(t) =60 exp (-‐0.1t) where t is in milliseconds Part C: Find iΔ when t > 0 By current divider: iΔ = 100/160 * iL (t) = 0.625* -‐2.4 exp (-‐100t) = -‐1.5 exp (-‐100t) with t in seconds or iΔ = -‐1.5 exp (-‐0.1t) with t in milliseconds