Download Flexmond ,new generation of flexible LED strip Signcomplex Printed

Signcomplex
Flexmond
TM
FlexmondTM , new generation of flexible LED strip
is so far the brightest flexible LED strip available in the market
Application
-
Cove lighting
Architectural lights for canopy,corridor,window,archway
Backlight or edge lighting for signage
DIY lights for home use
Path and contour marking
Decorative lights for holiday,event,show,exhibition
Printed circuit board layout
25mm .98
5.2mm/.2
8.3mm/.33
+
DC12V
_
500mm/20
LED Type Light OutputLight Output Beam Angle Voltage
(mcd)
(lumen)
(degrees)
(V DC)
Luminance(white 6500K)
Continuous
Max.Power
Consumption Connection
(w)
(m)
Model Number
Color
Length
(m)
SC-BID-W
White
5
600
Power
SMD
TOP LED
3500x600
5100
120
12
8
96
10
SC-BID-WW
Warm
White
5
600
Power
SMD
TOP LED
3000x600
4080
120
12
8
96
10
LED Q ty
Current
(Amps)
1
Signcomplex
Packing carton for 100 reels
580 mm
2
1
215mm
50mm
470mm
77mm
RoHS
Label
240mm
CAU TION
T H I S B A G C O N TA I N S
M O IS T U R E A N D E L EC T R O ST A T I C
S E NS I T I VE D E V I CE S
14.5cm
Attention
1.Storage Temperature:-40~+80 C,
Operating Temperature:-25~+60 C.
5.Strip can be cut following the cutting lines.
NQA
ISO 9001
REGISTERED COMPANY
UKAS
QUALITY
MANAGRMENT
4
3
2.Installation surface must be smooth,clean and dry.
3.The part of LED components can not be fixed on the surface of the sharp edge.
4.Stirp should not be collided or crushed.
RoHS
32
0m
Connectors for cut
m
1
3
SC-BID-CON1:Vertical connector
SC-BID-CON3:Ribbon to ribbon connector
2
4
SC-BID-CON2:T-shape connector
SC-BID-CON4:Ribbon to wire connector
Assembly Infor mation
- Solder connection should only be performed on designated solder pads(marked +/-).During soldering,don’t exceed the
maximum soldering time of 10 seconds and the maximum soldering temperature of 260 Celsius degrees.
- The smallest unit(25mm/1 -3 LEDs) can be removed by cutting with scissors between the designated solder pads.
- The mounting of the strip is facilitaed by means of the double-sided adhesive on the back-surface of the strip.Care must be
taken to provide a clean and dry mounting surface,free of oils or silicone coatings as well as dirt partide.The mounting substrate
must have sufficient structural integrity.Take care to completely remove the adhesive backing.Once the strip is appropriately
positioned.Press on the strip with about 20N/cm2(refer to application techniques of 3M adhesive transfer tapes).
- The minimum bending radius is 2 cm. The strip may be bent over a smaller radius of the circuit board containing no electronic
components and such bends should be made once and fixed in position to avoid cyclic fatigue.
Safety Infor mation
-The strip itself and
-Assembly must not da
ally stressed.
Signcomplex Limited
3-4/F,Bldg.C,Chuangfu Science&Technology Park,Beihuan Rd.,Shiyan Town ,Bao,an,Shenzhen,Guangdong,China
Tel:+86-755-27608650
Fax:+86-755-27608651
Email:[email protected]
www.signcomplex.com
2