Download ln-10 bench model - Lincoln Electric

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Document related concepts
no text concepts found
Transcript
B-12
B-12
OPERATION
1) Press end of gun against a solid object that is
electrically isolated from the welder output and
press the gun trigger for several seconds.
2) If the wire "birdnests", jams, or breaks at the drive
roll, the drive roll pressure is too great. Back the
pressure setting out 1/2 turn, run new wire through
gun, and repeat above steps.
3) If the only result is drive roll slippage, disengage
the gun, pull the gun cable forward about 6" (150
mm). There should be a slight waviness in the
exposed wire. If there is no waviness, the pressure is too low. Increase the pressure setting
turn, reconnect the gun, tighten locking clamp and
repeat the above steps.
4) Use Control Select and encoder knobs to set desired
Weld feed speed and voltage then Run-in speed and
voltage to optimize arc starting. (Set for each procedure if using front panel, remote control or optional
dual procedure switch.) (Refer to “Operation Keys”
and “Display Control Keys” in this section)
5) Adjust the wire feed acceleration if desired, for
each feeder and procedure. (Refer to “Acceleration
Selection” in this section)
6) Use Timer Select and Voltage Encoder knob to set
desired timers. (Refer to “Trigger Mode Selection”
in this section)
PROCEDURE FOR SETTING ANGLE
OF FEEDPLATE
7) Feed the electrode through the gun and cable and
then cut the electrode within approximately .38"
(9.5 mm) of the end of the contact tip for solid wire
and within approximately .75" (19mm) of the extension guide for cored wire.
1) Loosen the clamping collar screw using a 3/16"
Allen wrench. The clamping collar screw is
accessed from the bottom of the feedplate. It is
the screw which is perpendicular to the feeding
direction.
8) Connect work cable to metal to be welded. Work
cable must make good electrical contact to the
work. The work must also be grounded as stated in
"Arc Welding Safety Precautions".
WARNING
2) Rotate feedplate to the desired angle and tighten
clamping collar screw.
When using an Open Arc process,
it is necessary to use correct eye,
head, and body protection.
GAS GUARD REGULATOR SETTING
NOTE: Gas supply pressure must be regulated to a
maximum of 80 psi(5.5 bar).
1) With the gas supply shut off, the Gas Guard regulator flow adjusting Key should be set to maximum
(full clockwise) which is rated to be 60 SCFH (28
l/min).
2) Adjust gas supply flow rate for a level higher than
will be required, then adjust Gas Guard flow
adjusting Key counterclockwise to the desired gas
flow rate.
____________________________________
9) If used, be sure shielding gas valve is turned on.
10) Position electrode over joint. End of electrode
may be lightly touching the work.
11) Lower welding helmet, close gun trigger, and start
welding. Hold the gun so the contact tip to work
distance gives the correct electrical stickout as
required for the procedure being used.
12) To stop welding, release the gun trigger and then
pull the gun away from the work after the arc goes
out and Postflow time, if used, is over.
MAKING A WELD
1) Use only a Lincoln Electric recommended constant
voltage DC power source compatible with the LN10 Wire Feeder.
2) Properly connect the electrode and work leads for
the correct electrode polarity.
13) If necessary to optimize arc starting, readjust wire
speed acceleration, (Refer to “Acceleration
Selection” in this section) and/or Run-In speed,
(Refer to “Display Control Keys” in this section).
3) Use the Mode Selection key to set desired trigger
mode for each procedure. (Refer to “Trigger Mode
Selection” in this section)
LN-10