* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download IMPORTANT SAFEGUARDS
Survey
Document related concepts
Stray voltage wikipedia , lookup
Phone connector (audio) wikipedia , lookup
History of electric power transmission wikipedia , lookup
Electrical substation wikipedia , lookup
Electrification wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Power engineering wikipedia , lookup
Alternating current wikipedia , lookup
Solar micro-inverter wikipedia , lookup
Electric battery wikipedia , lookup
Buck converter wikipedia , lookup
Voltage optimisation wikipedia , lookup
Power inverter wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Transcript
I N S TA L L AT I O N I N S T R U C T I O N S LED EMERGENCY LIGHTING SYSTEM INVERTER/CHARGER MODEL PS2333 CAUTION: For safety and proper operation, read and follow instructions carefully before installation. CAUTION: A potential electrical hazard exists even when AC power supply has been turned off. Disconnect Battery Connector (2 red leads) before servicing. IMPORTANT NOTES: IMPORTANT SAFEGUARDS 1.READ AND FOLLOW ALL SAFETY INSTRUCTIONS 2. Before wiring to power supply, turn off electricity at fuse or circuit breaker. Make sure that branch circuit feeds are derived from a common phase for both normal lighting driver and PS2333 prior to installation. 3. To reduce the risk of electrical shock, disconnect AC power and unplug red battery connector before servicing. The PS2333 can be used with a switched or unswitched (night) circuit. When used with a switched fixture it is important to note that the power to the PS2333 inverter/ charger must be provided by an unswitched circuit. 5. Consult your local building code for approved wiring and installation. APPROXIMATE WORKING VOLTAGE Inverter/charger input: 120 OR 277V AC 4. All servicing should be performed by qualified personnel. 6. Do not use outdoors. This product is for use with indoor fixtures except air handling heated outlets, and wet or hazardous location fixtures. 7. The emergency ballast must be connected to an unswitched AC power source (120 or 277 volts). 8. Do not mount near gas or electric heater. 9. Equipment should be mounted in location and at heights where it will not readily be subjected to tampering by unauthorized personnel. 10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. 11. Do not use this equipment for other than intended use. SAVE THESE INSTRUCTIONS INSTALLATION PROCEDURE UNSWITCHED FIXTURE 1. Inspect PS2333 and make sure the battery connector (2 red leads) is not connected. 2. Remove fixture channel cover and install the Emergency Battery Pack on top of fixture (fig 1). Do not mount Emergency Battery Pack over LED driver. If necessary, drill holes and mount with screws (not provided). Emergency Battery Pack may also be remote mounted (fig 5). 3. Connect unit to driver and LED(s) as indicated in appropriate wiring diagram (fig A). 4. Install the pilot light and test switch as described in the section below, called INSTALLING PILOT LIGHT AND TEST SWITCH. DRIVER SWITCHED FIXTURE DRIVER 5. Wire Test Switch per figure 2. 6. In a readily visible location, attach the label "CAUTION: This Unit Has More Than One Power Supply Connection Point. To Reduce The Risk Of Electrical Shock, Disconnect Both The Branch Circuit Breakers Or Fuse And Emergency Power Supplies Before Servicing". Figure 2 7. Apply continuous power to PS2333. 8. Connect the battery connector (red leads). Figure 1 NOTE: Do not mount Emergency Battery Pack over A.C. Ballast. INSTALLING PILOT LIGHT AND TEST SWITCH PILOT LIGHT/TEST SWITCH ASSEMBLY 1. Drill 1/2" hole in fixture channel cover or other desired location for test switch. 2. Unscrew threaded nut . Insert test switch reattach nut . (see figure 3). 3. Drill second 1/2" hole for pilot light in hole. (see figure 3). Figure 4 Figure 3 Threaded Nut Test Switch Bushing Mesh Light Holder Pilot Light and . Install bushing 4. To mount pilot light through fixture housing, push pilot and mesh light holder back into bushing light (see Fig. 3). 5. To mount pilot light behind fixture lens, pull pilot light and mesh holder through bushing to desired length. (see figure 4, alternate mounting). NOTE: Allow battery to charge 24 hours before initial testing and 168 hours to fully charge battery. NOTE: Do not extend battery connector leads (red & red) and lamp selector (violet) leads.These connectors should be left in the junction box. JUNCTION BOX AND CONDUIT NOT SUPPLIED FOR REMOTE INSTALLATION. CAUTION: Damage to battery will occur if battery connection is made for a prolonged period of time without AC power provided. Figure 5 Page 2 ELECTRICAL SPECIFICATIONS Parameter Input Voltage Output Current Forward Voltage (Vfwd) Output Power @ 33 Volts Vfwd Units Vac mA Vdc W 120 Volt (Nom) 108-132 700 3-33 23 277 Volt (Nom) 250-305 700 3-33 23 WIRING DIAGRAM IMPORTANT NOTES: Before connecting battery connector, or wiring unit to fixture, refer to PS2333 INSTALLATION INSTRUCTIONS and IMPORTANT SAFEGUARDS for safety information and mounting procedures. Please consult the WIRING DIAGRAM below for wiring instructions. FIGURE A PAGE 3 www.powersentrysafety.com INSPECTION AND MAINTENANCE NOTE: Emergency lighting systems should be tested as often as local codes require, or at least quarterly to insure that all components are operational. Perform all tests required by local codes. 1. Check equipment rating to be sure that fixture will receive proper line voltage. 2. Be sure pilot light is on. If pilot light does not operate, check to see that: 1. AC power is on. 2. Voltage on branch circuit to Inverter/Charger is rated at line voltage (120V or 277V). If no line voltage can be measured, locate problem in branch circuit and correct. 3. Engage test switch. The pilot light should be off. The Emergency Battery Pack automatically switches to emergency power operating the LEDs. BATTERY REPLACEMENT 1. Disconnect inverter battery connector (2 red leads). 2. Disconnect both switched and unswitched power to fixture. 3. Remove screw located at end of lid, remove lid. 4. Unplug and remove old battery. Plug in new battery and place inside case. Reinstall inverter/charger lid. 5. Supply AC power to fixture and reconnect inverter battery connector (2 red leads). Pilot light should be illuminated. WARRANTY FIVE-YEAR TOTAL CUSTOMER SATISFACTION Complete Customer Satisfaction...This unit is guaranteed to perform to our customer’s complete satisfaction for a period of five years from date of invoice. Our guarantee covers any defect in manufacturing, provided the defect develops under normal and proper use. This liability does not include LED loads, and extends only to replacement of the defective part. Labor charges will be honored by the factory only with prior written approval from our Marketing Services Department. Document No. 912-00007-001 www.powersentrysafety.com Page 4