* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download 2 sin 2 2 90 1 2.5 90 .4 2 90 2 90 2 90 1.5 164.3 1 3.32 15.7 3.2 1.6
Regenerative circuit wikipedia , lookup
Index of electronics articles wikipedia , lookup
Topology (electrical circuits) wikipedia , lookup
Distributed element filter wikipedia , lookup
Yagi–Uda antenna wikipedia , lookup
Crystal radio wikipedia , lookup
Transistor–transistor logic wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Josephson voltage standard wikipedia , lookup
Integrating ADC wikipedia , lookup
Power electronics wikipedia , lookup
Valve audio amplifier technical specification wikipedia , lookup
Electrical ballast wikipedia , lookup
Power MOSFET wikipedia , lookup
Voltage regulator wikipedia , lookup
Surge protector wikipedia , lookup
Wilson current mirror wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Schmitt trigger wikipedia , lookup
Two-port network wikipedia , lookup
Current mirror wikipedia , lookup
Operational amplifier wikipedia , lookup
Valve RF amplifier wikipedia , lookup
Switched-mode power supply wikipedia , lookup
RLC circuit wikipedia , lookup
Standing wave ratio wikipedia , lookup
Current source wikipedia , lookup
Opto-isolator wikipedia , lookup
Impedance matching wikipedia , lookup
Rectiverter wikipedia , lookup
Homework 9 1) Perform the calculations below. Put your answer in polar notation. (2 j 3)(4 j ) 3.6156.3(4.12 14.0) 14.8742.3 e j 30 e j 24 0.866 j 0.5 0.914 j 0.41 1.78 j 0.09 1.782.89 1 2 j 2.24 63.4 0.62 97.1 3 2 j 3.6133.7 j j j 5 e 2 (e 3 ) e 6 1150 322 1.595 2 73 2) Use complex impedances to solve this circuit from Homework 8 for the steady state response, vc. Do not solve for the transient response. 1 3.2 2 sin(2t) 2 0.8 0.2 Vc Ans: You can approach the circuit as a voltage divider. The one branch, Z2 is the impedance formed by the capacitor and the other branch, Z1, is the impedance formed by the series combination of the resistor and inductor. Converting the input to its polar form and putting it into the voltage divider equation gives: 2sin 2t 2 90 1 j Z2 2.5 90 .4 vc 2 90 2 90 2 90 1.5 164.3 1 Z Z 3.32 15.7 2 1 3.2 j1.6 j .4 Or vc(t)= 1.5 cos(2t -164.3) 3) In the circuit below what are the currents in each of the elements in polar form? Graph them on a single graph to show their relationship. What is the total current delivered by the source? 1 2H 1 2 cos2t 2 Ans: Since the elements are each across the voltage source with no other impedances in series, we can quickly write the current for each element: vs 10 10 0.50 0.5 j 0 20 10 10 ic 290 0 j 2 1 0.5 90 j 2 10 10 il 0.25 90 0 j 0.25 j4 490 ir Summing the currents algebraically gives: iTOTAL=0.5+j1.75 Graphing them gives: ic ir il 4) In the circuit below, what is vo? Is the phase leading or lagging the input? + 1 1 Vo 3 4cos4t 3 - Ans: A good approach here would be to Thevenize the voltage source and the 1 and 3 ohm resistors. This gives: 3 vTH 4 3 4 1(3) RTH 0.75 (1 3) The Thevenin resistance in series with the impedance of the capacitor forms one leg of a voltage divider, Z1. The other 3 ohm resistor forms the second leg of the divider, Z2. We can then write the output from this: Z1 0.75 j 1 4 Z2 3 j0 Z2 30 vo 30 30 3.76 3.8 Z1 Z 2 vo 2.43.8 5) In this circuit, find i. Then use that to find vL and vR. Show that these two voltages add up as vectors to form the input, thus showing that KVL still holds. 1 2H 2cos2t 2 I 4 Ans: We can combine the impedance of the inductor in series with the resistor to form the total impedance in the circuit. The current is then the voltage source divided by this impedance. We can then find the voltage across the inductor and the resistor in turn by multiplying the impedance of each element by the current (Ohm’s Law for impedances). ZTOTAL 4 j 0 0 j 4 4 j 4 5.6645 20 0.354 45 5.6645 vL 490(0.354 45) 1.41445 i vR 40(0.354 45) 1.414 45 To show that the voltages add up as vectors: vL vR vS 6) Use complex impedances to find vo. + 1 2 1H 1/4 Vo 2 2 - cos2t Ans: The best way to tackle this would be to use nodal analysis. Writing the nodal equation leads directly to a solution for vo: 1 vo vo v o 1 2 2 j2 j 0.5 1 vo jvo 0.5vo j 0.5v0 vo 1 1 0.632 18.4 1.5 j 0.5 1.5818.4