Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
materials Article Novel Superdielectric Materials: Aqueous Salt Solution Saturated Fabric Jonathan Phillips Energy Academic Group, Naval Postgraduate School, Monterey, CA 93943, USA; [email protected] Academic Editor: Christof Schneider Received: 6 September 2016; Accepted: 3 November 2016; Published: 11 November 2016 Abstract: The dielectric constants of nylon fabrics saturated with aqueous NaCl solutions, Fabric-Superdielectric Materials (F-SDM), were measured to be >105 even at the shortest discharge times (>0.001 s) for which reliable data could be obtained using the constant current method, thus demonstrating the existence of a third class of SDM. Hence, the present results support the general theoretical SDM hypothesis, which is also supported by earlier experimental work with powder and anodized foil matrices: Any material composed of liquid containing dissolved, mobile ions, confined in an electrically insulating matrix, will have a very high dielectric constant. Five capacitors, each composed of a different number of layers of salt solution saturated nylon fabric, were studied, using a galvanostat operated in constant current mode. Capacitance, dielectric constant, energy density and power density as a function of discharge time, for discharge times from ~100 s to nearly 0.001 s were recorded. The roll-off rate of the first three parameters was found to be nearly identical for all five capacitors tested. The power density increased in all cases with decreasing discharge time, but again the observed frequency response was nearly identical for all five capacitors. Operational limitations found for F-SDM are the same as those for other aqueous solution SDM, particularly a low maximum operating voltage (~2.3 V), and dielectric “constants” that are a function of voltage, decreasing for voltages higher than ~0.8 V. Extrapolations of the present data set suggest F-SDM could be the key to inexpensive, high energy density (>75 J/cm3 ) capacitors. Keywords: dielectric; capacitance; energy storage 1. Introduction Two parallel, but technically distinct, efforts are underway for improving the energy density of capacitors: (i) employing electrically conductive materials with the highest possible surface areas as electrodes (EDLC, also known as supercapacitors); and (ii) finding/inventing electrically insulating materials with higher dielectric constants. In contrast to EDLC, the electrodes area in the high dielectric constant capacitors are quite low, approximately equal the macroscopic surface area. Increasing capacitance via the former route may have reached a limit with the deployment of graphene, “single layer” electrically conductive graphitic carbon, with a theoretical surface area limit of ~2600 m2 /gm. Until recently, efforts via the latter route focused primarily on improving barium titanate. Arguably this approach was not successful and significant improvements in energy storage density were not achieved. However, the recent invention of super dielectric materials, which employ dispersed liquids containing dissolved salts, not solids, as the dielectric (SDM) has dramatically improved energy density in capacitors based on this second approach. Indeed, the published energy density of prototypes of the two approaches are similar, with graphene based EDLC approaching 450 J/cm3 , and SDM based Novel Paradigm Supercapacitors (NPS) using aqueous solutions of NaCl in a anodized titania matrix as the dielectric with energy density of nearly 400 J/cm3 [1,2]. Previously, two types of materials were demonstrated to have dielectric constants greater than 5 10 , and hence qualify as super dielectric materials (SDM): (i) porous oxides (e.g., alumina) filled Materials 2016, 9, 918; doi:10.3390/ma9110918 www.mdpi.com/journal/materials Materials 2016, 9, 918 2 of 12 with aqueous salt solutions [3–5], so called Powder SDM (P-SDM); and (ii) anodized titania films, “Tube” SDM (T-SDM), also filled with aqueous salt solutions [1,2]. The measured dielectric constants of materials described in those studies was >1010 in many cases, hence orders of magnitude higher than required to meet the required minimum, greater than 105 , for a material to be classified as an SDM. In the present study a prediction of the general SDM hypothesis was tested: Any material composed of liquid containing dissolved, mobile ions, confined in an electrically insulating matrix, will have a very high dielectric constant. Specifically, a novel type of material that fits the above description was studied as a dielectric; nylon fabric saturated with aqueous NaCl salt solutions. Five capacitors composed of layers of this material were studied and each performed as superdielectric over the entire range of discharge rates studied. Once again, for slow discharge (ca. 100 s), dielectric constants as high as 1011 were measured, and, even at the shortest discharge rates, 0.001 s, no dielectric constant <107 was measured. Thus, the present work supports the general SDM hypothesis. Potentially, F-SDM are attractive engineering materials: inexpensive (fabric and salt water), easy to fabricate, and with a potential for high energy density. However; in order to better assess the applicability of F-SDM for fast discharge processes, the “roll-off” of capacitance with discharge time was studied. The very theory of SDM suggests they may be relatively slow to release energy. SDM are based on diffusion of ions inside the liquid filling the pores of the electrically insulating matrix material to form “giant” (ca. microns in length) dipoles upon exposure to an electric field. It takes time for the ions to move and form the multi-micron length dipoles required to explain super dielectric behavior. That is, ions initially randomly dispersed in a liquid must travel the order of the thickness of the dielectric layer (many microns in all cases studied to date) to ultimately create giant dipoles. Similarly, once formed, it takes time for the dipoles to “dissolve” allowing electrons on the electrodes to release. This model of multi-micron ionic travel under the influence of an applied field suggests there should be a time dependence to the capacitance of SDM. Qualitatively, it is anticipated that if the applied field is switched too quickly from one polarity to the opposite, the dipoles will not achieve their maximum possible magnitude. That is, the ions that form the dipole will simply not have time to travel to their equilibrium, fully polarized, positions. This in turn implies smaller effective dipoles at higher frequency, hence a lower effective dielectric constant. This should lead to a smaller measured capacitance with increasing frequency. One major objective of the present work is to quantify the effect of frequency on capacitance. The present data, based on constant current analysis between 2.3 and 0.1 volts, clearly show there is a strong roll-off of capacitance for F-SDM. The capacitance, from ~1 volt, at ~10 Hz is of the order of 1 percent that at ~0.01 Hz or to put it another way, the capacitance for a discharge time of 100 s is about 100 times greater than the capacitance for a discharge of 0.1 s. The dielectric constant shows nearly an identical rate of roll off, and the energy density measured over the full voltage range shows a slightly higher rate of roll off. This suggests the forming process for full strength dipoles in F-SDM take of the order of tens of seconds. This type of information clearly will help determine the suitability of F-SDM for particular applications. 2. Results The capacitance, measured dielectric constant, energy density and power delivery characteristics of five capacitors were studied as a function of discharge time (DT) defined as the time the voltage takes, during the discharge half-cycle, to drop from 2.3 to 0.1 volts. These capacitors were designed to be nearly identical in all respects except for the thickness, corresponding to the number of layers of nylon employed to create the dielectric layer (Table 1). Typical observed behavior for the “constant current” tests is shown in Figure 1 for several DT. A material with a voltage independent dielectric constant will produce a straight line, and it was consistently found that for the F-SDM studied herein, that is only approximately the case for DT > 50 s. As with previous studies of SDM materials, the dielectric constant is found to vary with voltage for DT less than about 50 s. Indeed, there are roughly three Materials 2016, 9, 918 3 of 12 <0.8 volts (Region III). For the present study, the dielectric constant values presented are those of regions III. of near constant dielectric constant: 2.3–1.6 V (Region I), 1.6–0.8 volts (Region II) and <0.8 volts Region (Region III). For the present study, the dielectric constant values presented are those of Region III. Table 1. Dielectric and Energy Density as a function of number of layers for 50 s DT. Table 1. Dielectric and Energy Density as a function of number of layers for 50 s DT. Approx. Dielectric Constant * Approx. Energy Density (J/cm3) ^ Layers Thickness (cm) DT ** 50 s (J/cm3 ) ˆ ** 50 s Constant * Approx. DT Dielectric Approx. Energy Density Thickness (cm) 9 1Layers 0.036 5 × 10 0.7 DT ** 50 s DT ** 50 s 2 0.074 2 × 1010 9 0.6 1 0.036 0.7 5 × 10 3 0.114 3 × 101010 0.2 2 0.074 0.6 2 × 10 10 0.15 5 3 0.191 5 × 10 0.114 0.2 3 × 1010 11 0.08 10 5 0.38 1.2 × 10 0.191 0.15 5× 1010 * Dielectric constants voltage voltage range, the 10 0.38 listed are for the 1.2 × 1011range 0.8–0.1 volts. Over this 0.08 dielectric constant was in fact constant. As noted in the text, the value of the constant * Dielectric constants listed are for the voltage range 0.8–0.1 volts. Over this voltage range, thedielectric dielectric constant was in factabove constant. in energy the text, density the valueis ofnot the dielectric decreases above ~0.8 V. ˆ The energy decreases ~0.8AsV.noted ^ The constantconstant but decreases with increasing thickness. density is not constant but decreases with increasing thickness. ** DT—Discharge time. Defined in text. ** DT—Discharge time. Defined in text. Figure 1. Cont. Materials 2016, 9, 918 Materials 2016, 9, 918 Materials 2016, 9, 918 4 of 12 4 of 12 4 of 12 Figure 1. 1. Five 54 ss showing showing one one cycle, cycle, and and illustrating illustrating three three Figure Five Layers Layers of of Nylon Nylon Cycles: Cycles: (A) (A) 12 12 mA, mA, DT DT ~~54 Figure 1.regions; Five Layers ofmA, Nylon Cycles: (A) 12 mA, DT(C) ~ 54 s mA, showing one cycle, and illustrating three voltage (B) 12 DT ~ 54 s, 7 cycles; and 90 DT ~ 0.25 s, 7 cycles. As shown, the voltage regions; (B) 12 mA, DT ~54 s, 7 cycles; and (C) 90 mA, DT ~0.25 s, 7 cycles. As shown, the first voltage regions; (B) 12 at mA, DT ~ 54 s,value 7 cycles; andtypical” (C) 90 mA, DT ~used 0.25ins,computation. 7 cycles. As shown, the first ~3 cycles collected any current are “not and not Note: Data ~3 cycles collected at any current value are “not typical” and not used in computation. Note: Data were first cycles collected at anyofcurrent value arethese “not two typical” and0.01 not used in computation. Note: Data were~3collected theof basis the smaller s, in all cases. (The collected on theon basis the smaller of theseoftwo values, values, 0.01 volts or volts 0.01 s,orin0.01 all cases. (The plotting were collected on the basis of the smaller of these two values, 0.01 volts or 0.01 s, in all cases. (The plottingfor routine for this figure data lumped data to approximately value routine this figure lumped to approximately one valueone every 0.5every s.) 0.5 s.) plotting routine for this figure lumped data to approximately one value every 0.5 s.) One general aspect of SDM behavior not described in earlier papers is the symmetry of One general general aspect aspect of of SDM SDM behavior not described described in in earlier papers papers is is the symmetry of One behavior not theSupercapacitors symmetry of charge/discharge behavior with respect to the polarity of the voltage.earlier As Novel Paradigm charge/discharge behavior with respect to the polarity of the voltage. As Novel Paradigm charge/discharge behaviorcreated with respect polarityof of two the voltage. As Novel Supercapacitors (NPS), that is capacitors fromtoa the sandwich low surface areaParadigm electrodes with an SDM Supercapacitors (NPS), that is capacitors created from a sandwich of two lowelectrodes surface area electrodes (NPS), that is capacitors created from a sandwich of two low surface area an SDM dielectric between, are completely symmetric, the expectation is that the charge/dischargewith behavior will with an SDM dielectric between, are completely symmetric, the expectation is that the charge/discharge dielectric between, completely symmetric, the expectation is thattothe behavior be symmetric with are respect to the sign of the voltage. This is shown be charge/discharge true in Figure 2. As shown,will the behavior will be symmetric with respect to the sign of theisvoltage. This is shown to be2.true in Figure 2. be symmetric with respect to the sign of the voltage. This shown to be true in Figure As shown, the voltage limits were set to be from −2.3 to +2.3 volts, whereas in all prior reports of SDM behavior the As shown, the were voltage set from −2.3whereas to +2.3 volts, in all of prior reports of SDM voltage setlimits to be were from −2.3to tobe+2.3 volts, in all whereas prior reports SDM behavior the voltage limits was never permitted to drop below zero volts. behavior the voltage was never permitted to drop below zero volts. voltage was never permitted to drop below zero volts. 2.0 2.0 VOLTS VOLTS 1.0 1.0 0 0 -1.0 -1.0 -2.0 -2.0 500 1000 500 1000 TIME, s TIME, s 1500 2000 1500 2000 Figure 2. Symmetric Capacitance. NPS capacitors are symmetric, hence can be charged and discharged Symmetric Capacitance. NPS capacitors are symmetric, symmetric, hence can be be Figure 2. Symmetric Capacitance. NPS are can and discharged from −2.3 to +2.3 Volts. Data shown arecapacitors from a five-layer sample,hence operated at charged 12 mA constant current − 2.3 to +2.3 Volts. Data shown are from a five-layer sample, operated at 12 mA constant from −2.3 to +2.3 Volts. Data shown are from a five-layer sample, operated at 12 mA constant current mode. current mode. mode. 2.1. Capacitance 2.1. Capacitance Capacitance for the voltage Region III is shown in Figure 3 for all five capacitors tested. In all forthe the voltage Region III is shown inpower Figure 3 all forwith all capacitors five capacitors tested. In all Capacitance for voltage Region is shown in aFigure 3 for five tested. In all cases, cases,Capacitance the capacitance “rolls off” very III smoothly as law decreasing discharge time. cases, the capacitance “rolls off” very smoothly as a power law with decreasing discharge time. the capacitance “rolls off” very smoothly as a power law with decreasing discharge time. Except for Except for the three-layer case, the same power law describes the roll off of all the test capacitors very Except for the three-layer case,power the same lawthe describes rollthe offtest of all the test capacitors the three-layer case, the same lawpower describes roll offthe of all capacitors very well:very well: well: −0.55 (1) Capacitance (1) 100× × (100/DT) (100/DT)−0.55 Capacitance= =CC 100 −0.55 (1) Capacitance = C100 × (100/DT) Materials 2016, 9, 918 Materials 2016, 9, 918 5 of 12 5 of 12 where C100 is the the capacitance capacitance at at 100 100 s, s, and and DT DT is the discharge time. time. Roughly, Roughly, this is equivalent to a 100 is roll off of 0.55 dB capacitance for 1.0 dB decrease in “period”. The “curve “curve fit” line of Equation (1) is the dashed curve in Figure 3. The same relationship also fits the dielectric data, substituting dielectric Inaddition, addition, nearly nearly the the same same relationship relationship fits virtually all constant for capacitance and “D 100”” for C100 100.. In the energy data (“E ” for C ), except the exponent is changed from − to indicating −0.60, indicating ” for C100100 ), except the exponent is changed from −0.55 to0.55 −0.60, a slightlya the energy data (“E100100 slightly fasterroll energy faster energy off. roll off. Figure Time. ForFor long discharge timetime (>100 s) capacitance increases with Figure 3. 3. Capacitance Capacitancevs. vs.Discharge Discharge Time. long discharge (>100 s) capacitance increases each additional layer, but for all capacitors, except three-layer, approximately the same simple power with each additional layer, but for all capacitors, except three-layer, approximately the same simple relationship (slope) (slope) between discharge time and describes the capacitive roll-off with power relationship between discharge timecapacitance and capacitance describes the capacitive roll-off decreasing discharge time. The dashed curve (above others) is the fit to Equation (1). with decreasing discharge time. The dashed curve (above others) is the fit to Equation (1). 2.2. 2.2. Dielectric Dielectric Constant Constant The The variation variation of of the the dielectric dielectric constant constant in in Region Region III III is is an an important important parameter, parameter, but but does does not not tell tell the entire story (Figure 4). The dielectric constant decreases with increasing voltage, and the ratio the entire story (Figure 4). The dielectric constant decreases with increasing voltage, and the ratio of of the the dielectric dielectric constants constants in in the the regions regions is is aa function function of of DT. DT. For For aa DT DT of of approximately approximately 11 s, s, the the dielectric dielectric constant for the the Region Region III III is is twice twicethat thatfor forRegion RegionIIIIand andfour fourtimes timesthat thatfor forRegion RegionI.I.For Fora aDT DTofof0.01 0.01s, constant for s, the dielectric constant for Region III is three time that for Region II and 10 times that of Region the dielectric constant for Region III is three time that for Region II and 10 times that of Region I. I. There There is is aa clear clear trend: trend: as as the the DT DT gets gets shorter, shorter, the the voltage voltage drops drops more more quickly quickly in in Regions Regions II and and II II relative to Region III. More detail on this behavior is found in earlier articles [1–5]. Rather than focus relative to Region III. More detail on this behavior is found in earlier articles [1–5]. Rather than focus on complex behavior, behavior, in inthis thispaper, paper,the thetrends trendsinintotal totalenergy energydensity, density, and power a function on this this complex and power as as a function of of DT, which includes contributions from all voltage regions, is reported. The total energy and power DT, which includes contributions from all voltage regions, is reported. The total energy and power are voltage regions. ThisThis lumping is necessary to more readily describe “nonare “lumped” “lumped”data datafrom fromallall voltage regions. lumping is necessary to more readily describe textbook”, that is voltage dependent capacitance, behavior. Moreover, the lumped values reflect net “non-textbook”, that is voltage dependent capacitance, behavior. Moreover, the lumped values reflect energy and and power behavior as a as function of the rate, rate, and concomitantly frequency. The net energy power behavior a function ofdischarge the discharge and concomitantly frequency. lumped values are significant indicators of performance in the likely applications: energy storage The lumped values are significant indicators of performance in the likely applications: energy storage and/or and/orpower powerdelivery. delivery. One significant One significant outcome outcome from from this this work, work, evident evident from from Figure Figure 44 and and Table Table 1, 1, are are the the remarkable remarkable 11 dielectric constants for Region III at long DT (>50 s) with the highest directly observed value3.5 3.5×× 10 1011 dielectric constants for Region III at long DT (>50 s) with the highest directly observed value (350 (350 billion) billion) for for aa discharge discharge time time of of the the 10 10 layer layer F-SDM F-SDM of of >200 >200s.s.Clearly, Clearly,F-SDM F-SDMare aresuperdielectrics. superdielectrics. One particular feature of the dielectric constants is that they are not constant, but rather increase with One particular feature of the dielectric constants is that they are not constant, but rather increase increasing thickness. It is revealing to compare this behavior with that of P-SDM for which with increasing thickness. It is revealing to compare this behavior with that of P-SDM for which the the “dielectric constants” are constant with thickness [3–5], and with T-SDM [1,2], for which the dielectric constants were found to increase approximately as 1/t2, where t is thickness of the dielectric layer. Materials 2016, 9, 918 6 of 12 Materials 2016, 9, 918 6 of 12 “dielectric constants” are constant with thickness [3–5], and with T-SDM [1,2], for which the dielectric constants were found to increase approximately as 1/t2 , where t is thickness of the dielectric layer. The increasing values valuesof of“dielectric “dielectricconstant” constant”for forthe the F-SDM illustrate a behavior “between” of The increasing F-SDM illustrate a behavior “between” thatthat of the the P-SDM and the T-SDM. That is, any increase is inconsistent with observed P-SDM behavior, but P-SDM and the T-SDM. That is, any increase is inconsistent with observed P-SDM behavior, but the the measured of increase much found for T-SDM. measured raterate of increase waswas much lessless thanthan thatthat found for T-SDM. DIELECTRIC CONSTANT 1.10 1.0x10 11 1.00E+11 1.0x1010 1.00E+10 1.0x109 1.00E+09 1 layer 2 layers 1.0x108 1.00E+08 3 layers 5 layers 1.00E+07 0.001 0.01 0.1 1 DISCHARGE TIME, S 10 100 1000 Figure Figure 4. 4. Dielectric DielectricConstant Constantvs. vs.Discharge DischargeTime. Time.In Inall allcases, cases,even evenfor fordischarge dischargetimes timesof oforder order0.001 0.001s,s, the >1077.. At the measured measured dielectric constant was >10 At relatively relatively long long discharge discharge times, times, >100 >100 s, s, the the dielectric dielectric 10 in constants constants were, remarkably, >1010 inall allcases. cases. 2.3. 2.3. Energy Energy Density Density Energy Energy density density data data were were obtained obtained in in two two steps. steps. First, First, the the area area under under the the entire entire constant constant current current curve, 2.3–0.1 V, is integrated to yield “volt-seconds”, this is multiplied by the constant current to curve, 2.3–0.1 V, is integrated to yield “volt-seconds”, this is multiplied by the constant current to yield yield energy (integration of “power”, where power is volts × current). This procedure is required energy (integration of “power”, where power is volts × current). This procedure is required because because energybecannot be determined from simple the usual simple relationship between and energy cannot determined from the usual relationship between energy and energy capacitance capacitance because capacitance changes with voltage. Nonetheless, there is a smooth relationship because capacitance changes with voltage. Nonetheless, there is a smooth relationship between energy between energy andEnergy, discharge time. Energy, like off smoothly for and discharge time. like capacitance, rolls offcapacitance, smoothly forrolls all capacitors tested asall thecapacitors discharge tested as the discharge times reduced (Figure 5). Once again, the roll-off rates are nearly “parallel” times are reduced (Figure 5).are Once again, the roll-off rates are nearly “parallel” independent of the independent of the number of layers. An interesting feature of the data is that, even for the relatively number of layers. An interesting feature of the data is that, even for the relatively thick 1 layer capacitor thick 1 layer capacitor (360greater μ), an energy greater thanmeasured 1 J/cm3 was measured fortimes. very (360 µ), an energy density than 1 density J/cm3 was directly fordirectly very long discharge long discharge times. Although not even close to that recorded for T-SDM [1,2], relative to the best Although not even close to that recorded for T-SDM [1,2], relative to the best barium titanate based barium titanate based electrostatic capacitors this is a remarkable value [6–8]. electrostatic capacitors this is a remarkable value [6–8]. The The increasing increasing energy energy density density with with decreasing decreasing thickness thickness suggests suggests that that aa thin thin fabric fabric type type SDM SDM could rival the TSDM energy density observed in earlier studies. Indeed, a conservative extrapolation, could rival the TSDM energy density observed in earlier studies. Indeed, a conservative extrapolation, based on aa the the empirical empiricalfinding findingofofone oneorder order magnitude increase in net energy density for each based on ofof magnitude increase in net energy density for each one one order of magnitude decrease in thickness (see Table 1),anand an energy density 100 sthat twice order of magnitude decrease in thickness (see Table 1), and energy density at 100 at s twice at that 50 s, 3 for a 5 micron thick nylon layer and discharge time 3 for at 50 s, indicates an density energy density of >75 J/cm indicates an energy of >75 J/cm a 5 micron thick nylon layer and discharge time of 100 s. of 100 s. Materials 2016, 9, 918 7 of 12 Materials 2016, 9, 918 Materials 2016, 9, 918 7 of 12 7 of 12 1 1 ENERGY DENSITY, J/CM3 ENERGY DENSITY, J/CM3 0.1 0.1 0.01 1 layer 0.01 2 layers 1 layer 3 layers 2 layers 5 layers 3 layers 10 layers 5 layers 0.001 0.001 0.0001 0.001 0.0001 0.001 10 layers 0.01 0.1 1 10 100 DISCHARGE TIME, S 0.01 0.1 1 10 100 S Figure 5. Energy Density vs. Discharge Time. DISCHARGE The initialTIME, energy density at long discharge times is Figure 5. Energy Density vs. Discharge Time. The initial energy density at long discharge times is highest for one layer and decreases with each added layer, but the power law relationship (slope) Figurefor 5. Energy Density vs. Discharge initial energy at long times is highest one layer and decreases withTime. each The added layer, but density the power law discharge relationship (slope) between energy density and discharge time is very similar for all capacitors studied. highestenergy for onedensity layer and added layer, power law relationship (slope) between anddecreases dischargewith timeeach is very similar forbut allthe capacitors studied. between energy density and discharge time is very similar for all capacitors studied. 2.4. Power Density 2.4. Power Density The Density power delivery as a function of frequency clearly increases as the discharge times are 2.4. Power The power delivery as a function of frequency increases as discharge are reduced reduced (Figure 6). Power was computed simplyclearly by determining thethe total energy,times computed as The power delivery as a function of frequency clearly increases as the discharge times are described above, and dividing itsimply by the by discharge time. The in power delivered a discharge (Figure 6). Power was computed determining theincrease total energy, computed asat described above, reduced (Figure 6). Power was computed simply by determining the total energy, computed as of 0.01its,by a typical high power application time,in is power more than an orderatofa magnitude greater, andtime dividing the discharge time. The increase delivered discharge time of in 0.01 s, described above, and dividing it by the discharge time. The increase in powerincrease delivered at a discharge all cases, than the power delivered during a 100 s discharge. The measured in power with a typical high power application time, is more than an order of magnitude greater, in all cases, than time of 0.01 s, typical high power application time, the is more than anroll order magnitude greater, decreasing DTa is anticipated system for which capacitance offpower isofless than 1 dB per 1 dBinDT theallpower delivered during a for 100any s discharge. The measured increase in with decreasing cases, than the power delivered during a 100 s discharge. The measured increase in power with decrease in discharge time. That is, as long as the exponent in Equation (1) is greater than negative is anticipated for any system for which the capacitance roll off is less than 1 dB per 1 dB decrease decreasing DTwill is anticipated fordecreasing any systemDT forvalue. which the capacitance roll off is less than 1 dB per 1 dB in one, power increase with discharge That is,time. as long asis, the inexponent Equationin(1) is greater negative power decreasetime. in discharge That asexponent long as the Equation (1) than is greater thanone, negative 0.5 will increase with decreasing DT value. one, power will increase with decreasing DT value. 0.5 POWER, W/CM3 POWER, W/CM3 0.05 0.05 1 layer 0.005 2 layers 1 layer 3 layers 0.005 25layers layers 310 layers layers 5 layers 0.0005 0.001 10 layers 0.01 0.1 1 DISCHARGE TIME, S 10 100 0.0005 Figure 6. Power vs. Discharge Time. The power observed decreases monotonically with the number 0.001 0.01 0.1 1 10 100 of layers. Notably, the power increases with DISCHARGE decreasing times. This is because the roll-off TIME,discharge S of energy is slower than the “roll-off” of discharge time. Figure 6. Power vs. Discharge Time. The power observed decreases monotonically with the number Figure 6. Power vs. Discharge Time. The power observed decreases monotonically with the number of of layers. Notably, the power increases with decreasing discharge times. This is because the roll-off layers. Notably, the power increases with decreasing discharge times. This is because the roll-off of of energy is slower than the “roll-off” of discharge time. energy is slower than the “roll-off” of discharge time. Materials 2016, 9, 918 Materials 2016, 9, 918 8 of 12 8 of 12 It should should be noted noted that that the the typical typical “Ragone “Ragone chart” (Figure 7) presentation presentation of data reflects the the same aspects of behavior seen in the above capacitance, energy and power vs. discharge time plots [9]. same Specifically, Specifically, as as frequency frequency increases increases (nearly (nearly equivalent equivalent to to decreasing decreasing discharge discharge time), time), the the capacitance capacitance rolls linear relationship between energy and capacitance, as frequency increases, energy rolls off. off.Given Giventhe the linear relationship between energy and capacitance, as frequency increases, density decreases. As shown in Figure 7, the Energy vs. Power curve can be readily fit with a singlea energy density decreases. As shown in Figure 7, the Energy vs. Power curve can be readily fit with power law forlaw F-SDM. In contrast, for many apparently, there is athere change “power single power for F-SDM. In contrast, forsupercapacitors, many supercapacitors, apparently, is a in change in law” such that power output reaches a maximum even as energy continues to drop. “power law” such that power output reaches a maximum even as energy continues to drop. 1 ENERGY J/CM3 0.1 0.01 0.001 1 Layer 10 Layers 0.0001 0.0001 0.001 0.01 POWER J/CM3 S 0.1 Figure 7. 7. Ragone Ragone Plot Plot Presentation. Presentation. The The data data obtained obtained for for two two of of the the F-SDM F-SDM based based capacitors capacitors studied studied Figure are shown. As with other types of capacitors, as the energy density decreases, the power output are shown. As with other types of capacitors, as the energy density decreases, the power output increases. The basis for this relationship is that as the discharge time decreases, the energy density increases. The basis for this relationship is that as the discharge time decreases, the energy density decreases, but but more more slowly. slowly. Thus, Thus, the the energy energy delivered delivered per per unit unit time time (power) (power) increases increases with with decreasing decreasing decreases, discharge time. time. discharge 3. Discussion 3. Discussion The basis basis for for the the SDM SDM hypothesis: hypothesis: Dielectrics capacitance by reducing the the field field The Dielectrics increase increase capacitance by reducing everywhere relative to the no dielectric case. Specifically, any dielectric exposed to a field created by everywhere relative to the no dielectric case. Specifically, any dielectric exposed to a field created by charge on on electrodes electrodes forms forms dipoles dipoles that that create create fields fields “opposite” “opposite” the the field field generated generated by by the the charge charge on on charge the electrodes. Relative to the “dielectric free” situation, this reduces the net electric field strength the electrodes. Relative to the “dielectric free” situation, this reduces the net electric field strength everywhere. InInturn, this reduces the the work, that is the is integral of electric field over anyover path any (voltage), everywhere. turn, this reduces work, that the integral of electric field path necessary to bring another charge to thecharge electrode surface. Thus,surface. when a dielectric is present between (voltage), necessary to bring another to the electrode Thus, when a dielectric is parallel plates, more charge is necessary to create same voltage reached in thevoltage absencereached of a dielectric. present between parallel plates, more charge is the necessary to create the same in the This is of equivalent to This increasing the charge/voltage ratio, which is the definition of increasing absence a dielectric. is equivalent to increasing the charge/voltage ratio, which is the definition capacitance. any dielectric produce dipoles larger than those in solids of increasingHence, capacitance. Hence, that any can dielectric that can produce dipoles larger than barium those intitanate solids should have a dielectric constant higherconstant than thathigher foundthan for that understanding barium titanate should have a dielectric that material. found forThe thatabove material. The above motivated the design of the wit: Awork. nylonTofabric saturated with saturated “salt water” should understanding motivated thepresent designwork. of theTo present wit: A nylon fabric with “salt have dipoles as long as the thickness of the nylon, at least thousands of times larger than that of any water” should have dipoles as long as the thickness of the nylon, at least thousands of times larger solid, including BaTiO3. Thus the dielectric constant of an SDM is predicted to be much higher than than that of any solid, including BaTiO3 . Thus the dielectric constant of an SDM is predicted to be that of any solid. much higher than that of any solid. The first major empirical finding supports the above predicted high dielectric: the measured The first major empirical finding supports the above predicted high dielectric: the measured dielectric constants are above 1077 (vs. <1044 for barium titanate) even at very short discharge times, dielectric constants are above 10 (vs. <10 for barium titanate) even at very short discharge times, establishing F-SDM as a new class of SDM. Second, the capacitance and dielectric constant changes establishing F-SDM as a new class of SDM. Second, the capacitance and dielectric constant changes with voltage in a very similar pattern to that for aqueous based P-SDM and T-SDM. That is, the with voltage in a very similar pattern to that for aqueous based P-SDM and T-SDM. That is, the capacitance changes with voltage, but can be well modeled as constant in three voltage zones for capacitance changes with voltage, but can be well modeled as constant in three voltage zones for discharge times less than ca. 25 s. Third, the relatively slow increase in dielectric constant with increasing layer thickness demonstrates this class of materials is not like P-SDM, and, the measured Materials 2016, 9, 918 9 of 12 discharge Materials 2016,times 9, 918 less than ca. 25 s. Third, the relatively slow increase in dielectric constant 9with of 12 increasing layer thickness demonstrates this class of materials is not like P-SDM, and, the measured with dielectric layer thickness indicates behavior that is distinct from and clear clear drop dropininenergy energydensity density with dielectric layer thickness indicates behavior that is distinct T-SDM. The behavior of F-SDM is unique (Figure 8). Fourth, there is aistypical pattern decrease in from T-SDM. The behavior of F-SDM is unique (Figure 8). Fourth, there a typical pattern decrease capacitance, dielectric constant and energy density with decreasing discharge time. Fifth, extrapolating in capacitance, dielectric constant and energy density with decreasing discharge time. Fifth, the energy density values for thevalues relatively thick samples studied suggests that capacitors with extrapolating the energy density for the relatively thick samples studied suggests thatmade capacitors 3 ). 3 thin fabric layers (ca. 5 µ) might have exceptional energy densities (ca. >75 J/cm made with thin fabric layers (ca. 5 μ) might have exceptional energy densities (ca. >75 J/cm ). NORMALINZED ENERGY DENSITY 1 0.1 Measured Standard Theory SDM Theory 0.01 1 NUMBER OF LAYERS 10 Figure toto SDM theory (solid line), thethe energy density is Figure 8. 8. Energy Energy Density Densityvs. vs.Thickness. Thickness.According According SDM theory (solid line), energy density independent of thickness. According to standard theory (dashed line) the energy density falls as is independent of thickness. According to standard theory (dashed line) the energy density falls as inverse inverse thickness thickness squared. squared. The The actual actual data data (points/dotted (points/dotted line) line) for for energy energy density density as as aa function function of of dielectric thickness fall between these two theories. dielectric thickness fall between these two theories. A low surface area nylon mesh containing a salt solution is predicted to have a high dielectric A low surface area nylon mesh containing a salt solution is predicted to have a high dielectric constant by the SDM theory, but not by any other theory. A brief review shows no viable alternative constant by the SDM theory, but not by any other theory. A brief review shows no viable alternative models in the literature. Alternative theories of high dielectric constants include high dielectric models in the literature. Alternative theories of high dielectric constants include high dielectric constants at the percolation threshold [10–12], a nano metal particle model [13–15], and a quantum constants at the percolation threshold [10–12], a nano metal particle model [13–15], and a quantum “surface state” model for colossal dielectric behavior [16–20]. As discussed elsewhere, none of these “surface state” model for colossal dielectric behavior [16–20]. As discussed elsewhere, none of these models appears to provide a reasonable framework for understanding the current system [1–5]. models appears to provide a reasonable framework for understanding the current system [1–5]. Specifically, there is no conceivable percolation process [21], there are no metal particles, and there Specifically, there is no conceivable percolation process [21], there are no metal particles, and there are no surface states associated with the liquid phase. Finally, NPS are clearly not a variation on are no surface states associated with the liquid phase. Finally, NPS are clearly not a variation on electric double layer capacitors (EDLC), as the NPS capacitors are missing two elements of standard electric double layer capacitors (EDLC), as the NPS capacitors are missing two elements of standard supercapacitors: a high surface area conductive electrode (e.g., graphene), and a thin separator to supercapacitors: a high surface area conductive electrode (e.g., graphene), and a thin separator to allow ion transport, but to keep the two high surface area electrodes from touching/shorting [22,23]. allow ion transport, but to keep the two high surface area electrodes from touching/shorting [22,23]. Another issue requiring discussion is the “in-between” PSDM and TSDM behavior observed. In Another issue requiring discussion is the “in-between” PSDM and TSDM behavior observed. P-SDM dipole length, critical in determining dielectric constant, is established by the pore structure In P-SDM dipole length, critical in determining dielectric constant, is established by the pore structure of the powder employed. Pore structure does not change with thickness, hence the dielectric constant of the powder employed. Pore structure does not change with thickness, hence the dielectric constant is unchanging, as observed [3–5]. Energy density drops, consequently, as expected (thickness−−22) for is unchanging, as observed [3–5]. Energy density drops, consequently, as expected (thickness ) for any standard dielectric material. In T-SDM, the dipole length is determined by the length of the open any standard dielectric material. In T-SDM, the dipole length is determined by the length of the pores in the titania structure. These pores run the width of the oxide layer. Thus, as the dipole length open pores in the titania structure. These pores run the width of the oxide layer. Thus, as the dipole increases exactly at the same rate as the dielectric layer thickness, the amount of salt also increases length increases exactly at the same rate as the dielectric layer thickness, the amount of salt also proportional to the pore length, and concomitantly so does the dielectric constant. This is not increases proportional to the pore length, and concomitantly so does the dielectric constant. This is “standard” behavior for dielectric materials, but is anticipated for TSDM as explained in earlier not “standard” behavior for dielectric materials, but is anticipated for TSDM as explained in earlier publications [1,2]. Moreover, the theory of energy density for a system of ever increasing pore length is that energy density should be largely independent of dielectric thickness, as observed. It is argued that pore length change with increasing dielectric layer thickness for an F-SDM is between those observed for PSDM and TSDM. The pore length is anticipated to increase with dielectric layer thickness, but at a slower rate than that of the dielectric layer itself. That is, it is Materials 2016, 9, 918 10 of 12 publications [1,2]. Moreover, the theory of energy density for a system of ever increasing pore length is that energy density should be largely independent of dielectric thickness, as observed. It is argued that pore length change with increasing dielectric layer thickness for an F-SDM is between those observed for PSDM and TSDM. The pore length is anticipated to increase with dielectric layer thickness, but at a slower rate than that of the dielectric layer itself. That is, it is anticipated that there is not perfect alignment between the layers of nylon fabric. Hence, liquid containing holes (~50% by area) in the mesh only partially “line up”, limiting the average pore length increase with the addition of each layer. This limits the average increase in dipole length with increasing number of layers. The average dipole length does increase with each layer added, but not as quickly as the overall thickness. This qualitative explanation is consistent with the observed change in energy density with number of layers. The final point of interest is the decrease in dielectric constant and concomitantly energy density with decreases in discharge time. A reasoned extrapolation of the SDM theory suggests this is to be expected. Indeed, each time the applied field is reversed the original dielectric constant will not be recovered until all the ions in the solution within a pore physically move by diffusion, or field assisted convection, to the “other side” of the pore. This takes time. If the discharge time is too short, complete reversal of the ions will not take place, leading to a smaller net dipole strength within the pore, and hence a lower net dielectric constant. As the charge time gets shorter, the net motion is less, and hence the value of the dielectric constant should fall as the charge time decreases. This model leads to several questions for future work. First, will other dielectrics for which physical motion of ions is required show a similar fall off of capacitance as discharge time is reduced? In particular, will a similar discharge time dependence of dielectric constant be observed in EDLC? In addition, if the charging time is increased at any given current, will the energy density at any given discharge current increase? 4. Materials and Methods Capacitor Fabrication: All capacitors, so-called Novel Paradigm Supercapacitors (NPS), were created from three components: nylon fabric, aqueous solutions of NaCl (30 wt %), and GTA grade Grafoil [24,25] electrodes (0.4 mm thick × 5 cm diameter), a commercially available, paper-like (~0.4 mm thick), moderate surface area (~20 m2 /gm) material composed of compressed graphite (>99%). Nylon fabric squares, ~5.1 cm on a side, nominal thickness 0.36 mm, 50% open space, were dipped into the salt solution for approximately one hour, and then smoothed onto a Grafoil electrode. For the multi-layer samples, additional salt solution saturated fabric layers were added one at a time. The second Grafoil electrode was then placed on top and the thickness of the capacitor determined from an average of four measurements with a micrometer. Once the capacitor “sandwich” was created, in order to retard drying, it was placed on a small plastic block, and the block placed in a plastic bag containing water saturated cloth (3). Measurement: The capacitive behavior was determined using a BioLogic Model SP 300 Galvanostat (Bio-Logic Science Instruments SAS, Claix, France) in constant current charge/discharge mode. Data were collected from the smaller of these intervals: 0.01 s or 0.01 V Other methods were judged to be inappropriate for determination of characteristics as prior SDM studies clearly show that the capacitance of NPS is a strong function of voltage. Hence, methods such as impedance spectroscopy that measure the dielectric constant at a single voltage, generally 0 ± 15 mV [8,9], do not yield the full story regarding energy storage characteristics. For a reliable understanding of the behavior expected for energy storage devices, the behavior over the entire voltage operating range must be studied [6,26,27]. At each selected constant current at least ten complete cycles were recorded, and generally twenty. This method does not permit the selection of the discharge rate; however, the discharge rate is a function of the discharge current. Thus, the trend in dielectric constants and energy density was determined by variation of the controllable parameter, discharge current. In all cases the charging current was the same magnitude as the discharge current, but of opposite sign. Materials 2016, 9, 918 11 of 12 There are several potential sources of error in determination of capacitance and dielectric constant. First, is the measured current. Observation clearly showed this to be within 3% of the nominal current in all cases. A second source is in measurement of the capacitor thickness. In all cases, that was determined to be no greater than ±0.03 mm, which, for all capacitors studied, was less than 10%. Variation in the slope of the discharge (dI/dV), determined by measurement of multiple discharges, was found to be no more than 5%, indicating precision. Consideration of all these errors suggests the values presented in the results section are ±15% of true values. It is notable in this regard that a 220 µF commercial superdielectric capacitor (Maxwell) was studied as a “control” in the same circuit, over the same voltage range. The measured capacitance at 0.03 Hz was 215 µF, and was constant over nearly the entire voltage range. The voltage range in most cases was selected to be between 2.3 and 0.1 volts (Figure 1) as earlier studies showed this range to be compatible with aqueous solution based SDM [1–5]. For illustration purposes, one example of a charge/discharge cycle operating between −2.3 and +2.3 volts is shown (Figure 2). Acknowledgments: The author is grateful that this study was fully supported by the Office of Naval Research and the Naval Research Program administered by the Naval Postgraduate School, Monterey, CA, USA. Conflicts of Interest: The author declares no conflict of interest. References 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Gandy, J.; Quintero, F.; Phillips, J. Testing the Tube Super Dielectric Material Hypothesis: Increased Energy Density Using NaCl. J. Electron. Mater. 2016. [CrossRef] Quintero, F.; Phillips, J. Tube-Super Dielectric Materials: Electrostatic Capacitors with Energy Density Greater than 200 J·cm−3 . Materials 2015, 8, 6208–6227. Fromille, S.; Phillips, J. Super Dielectric Materials. Materials 2014, 7, 8197–8212. [CrossRef] Quintero, F.; Phillips, J. Super Dielectrics Composed of NaCl and H2 O and Porous Alumina. J. Electron. Mater. 2015, 44, 1367. Jenkins, N.; Petty, C.; Phillips, J. Investigation of Fumed Aqueous NaCl Superdielectric Material. Materials 2016, 9, 118. [CrossRef] Reynolds, G.J.; Krutzer, M.; Dubs, M.; Felzer, H.; Mamazza, R. Electrical properties of thin-film capacitors fabricated using high temperature sputtered modified barium titanate. Materials 2012, 5, 644–660. [CrossRef] Kinoshita, K.; Yamaji, A. Grain-size effects on dielectric properties in barium titanate ceramics. J. Appl. Phys. 1976, 47, 371–373. [CrossRef] Arlt, G.; Hennings, D. Dielectric properties of fine-grained barium titanate ceramics. J. Appl. Phys. 1985, 58, 1619–1625. [CrossRef] Christen, T.; Carlen, M.W.J. Theory of Ragone Plots. J. Power Sources 2000, 91, 210–216. [CrossRef] Bergman, D.J.; Imry, Y. Critical behavior of the complex dielectric constant near the percolation threshold of a heterogeneous material. Phys. Rev. Lett. 1977, 39, 1222. [CrossRef] Efros, A.L.; Shklovskii, B.I. Critical Behaviour of Conductivity and Dielectric Constant near the Metal-Non-Metal Transition Threshold. Phys. Status Solidi B 1976, 76, 475–485. [CrossRef] Efros, A.L. High volumetric capacitance near the insulator-metal percolation transition. Phys. Rev. B 2011, 84, 155134. [CrossRef] Pecharroman, C.; Esteban-Betegon, F.; Bartolome, F.; Lopez-Esteban, J.F.; Moya, J. New Percolative BaTiO3 –Ni Composites with a High and Frequency-Independent Dielectric Constant (r ≈ 80000). Adv. Mater. 2001, 13, 1541–1544. [CrossRef] Pecharroman, C.; Esteban-Betegon, F.; Jimenez, R. Electric field enhancement and conduction mechanisms in Ni/BaTiO3 percolative composites. Ferroelectrics 2010, 400, 81–88. [CrossRef] Saha, S.K. Observation of giant dielectric constant in an assembly of ultrafine Ag particles. Phys. Rev. B 2004, 69, 125416. [CrossRef] Lunkenheimer, P.; Krohns, S.; Riegg, S.; Ebbinghaus, S.G.; Reller, A.; Loidl, A. Colossal dielectric constants in transition-metal oxides. Eur. Phys. J. 2009, 180, 61–89. [CrossRef] Materials 2016, 9, 918 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 12 of 12 Lunkenheimer, P.; Bobnar, V.; Pronin, A.V.; Ritus, A.I.; Volkov, A.A.; Lodl, A. Origin of apparent colossal dielectric constants. Phys. Rev. B 2002, 66, 052105. [CrossRef] Hu, W.; Lau, K.; Liu, Y.; Withers, R.L.; Chen, H.; Fu, I.; Gong, B.; Hutchison, W. Colossal Dielectric Permittivity in (Nb + Al) Codoped Rutile TiO2 Ceramics: Compositional Gradient and Local Structure. Chem. Mater. 2015, 27, 4934–4942. [CrossRef] Krohns, S.; Lu, J.; Lunkenheimer, P.V.; Brize, V.; Autret-Lambert, C.; Gervais, M.; Gervais, F.; Bouree, F.; Porcher, F.; Loidl, A. Correlations of structural, magnetic, and dielectric properties of undoped and doped CaCu3 Ti4 O12 . Eur. Phys. J. B 2009, 72, 173–182. [CrossRef] Kant, C.; Rudolf, T.; Mayr, F.; Krohns, S.; Lunkenheimer, P.; Ebbinghaus, S.G.; Loidl, A. Broadband dielectric response of CaCu3 Ti4 O12 : From dc to the electronic transition regime. Phys. Rev. B 2008, 77, 045131. [CrossRef] Gerenrot, D.; Berlyand, L.; Phillips, J. Random network model for heat transfer in high contrast composite materials. IEEE Trans. Adv. Packag. 2003, 26, 410–416. [CrossRef] Conway, B.E.E. Electrochemical Supercapacitors. In Scientific Fundamentals and Technological Applications; Spinger Science and Business Media: Berlin/Heidelberg, Germany, 2013. Gualous, H.; Bouquain, D.; Berthan, A.; Kauffmann, J.M. Experimental study of supercapacitor serial resistance and capacitance variations with temperature. J. Power Sources 2003, 123, 86–93. [CrossRef] Phillips, J.; Clausen, B.; Dumesic, J.A. Iron pentacarbonyl decomposition over Grafoil. Production of small metallic iron particles. J. Phys. Chem. 1980, 84, 1814–1822. [CrossRef] Phillips, J.; Dumesic, J.A. Iron pentacarbonyl decomposition over Grafoil: II. Effect of sample outgassing on decomposition kinetics. Appl. Surf. Sci. 1981, 7, 215–230. [CrossRef] Kim, Y.; Kathaperumal, M.; Chen, V.W.; Park, Y.; Fuentes-Hernandez, C.; Pan, M.J.; Kippelen, B.; Perry, J.W. Bilayer Structure with Ultrahigh Energy/Power Density Using Hybrid Sol–Gel Dielectric and Charge-Blocking Monolayer. Adv. Energy Mater. 2015. [CrossRef] Gogotski, Y.; Simon, P. True performance metrics in electrochemical energy storage. Science 2011, 334, 917–918. [CrossRef] [PubMed] © 2016 by the author; licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC-BY) license (http://creativecommons.org/licenses/by/4.0/).