Download INSTALLATION NOTES: dAlta-5,-7 and dLuna-4,-6

INSTALLATION NOTES: dAlta-5,-7 and dLuna-4,-6
1. Caution and Safety Instructions
• Qualified personnel must install and/or service product in a manner consistent with its intended use and in compliance with the National Electrical Code, Canadian Electrical Code, and/or all local and provincial codes.
• Follow all product label information and
installation instructions.
• Turn off power at the fuse or circuit breaker before installation or servicing.
• The use of damaged components may cause an unsafe condition and void the product warranty.
• Do not block light emanating from the product in
whole or part.
• Never operate the fixture with a missing or damaged lens. Clean the lens on a regular basis.
• The entire fixture may become extremely hot. Do not touch the hot lens or fixture body. Do not touch the light source at any time.
• Keep all O-rings and sealing surfaces clean during installation and servicing; failure to do this may lead to premature failure of the product.
2. Product Information
Tools Needed:
• ⅛" Allen wrench (installation)
dAlta-7
3YJ8
dAlta-5
Power Requirements
Low Voltage (LV)
dLuna-6
Input Power
12V
Dimming
Phase or PMW
Number of Wires
2
dLuna-4
ARCHITECTURAL & LANDSCAPE LIGHTING | holmlighting.com
A Hunter Industries Company
INSTALLATION NOTES: dAlta-5,-7 and dLuna-4, -6
3. Product Installation
Diagrams
the lens(es) off. Repeat to remove multiple lenses. Once
removed, reattach the new color and/or beam angle lens
by lining up the bayonet mount and twisting clockwise
1/4 turn while gently pressing down. If using an accessory
lens (e.g., hex baffle, spread lens, etc.), insert the lens into
the back end of the shroud to mate with the glass lens.
Reinstall the lens cap by firmly pressing it past the double
O-rings and flush with main fixture. Complete the
servicing by refastening the setscrew.
Waterproof
connection
Servicing
The LED board in this product is designed to offer
years of use without replacement. If a failure occurs,
please contact the local authorized manufacturer’s
representative.
Weep hole
Setscrew
Installation Guidelines
The dAlta-5, -6, and -8 models are integrated LED fixtures
capable of housing various LED boards designed by Holm.
The size of each fixture corresponds to the size of each
compatible LED board. For example: dAlta-5 (1LED),
dBeam-6 (1LED, 3LED, and ZDC), or dAlta-8 (1LED, 3LED,
6LED, 9LED, and ZDC).
Installation Requirements
Install all three models in the upward facing direction
only. Ensure the fixture is aligned in a manner such that
the setscrew and weep hole are pointed downward. Using
these models as a down lights may lead to failure.
Changing or Removing Lenses
To add or remove a color filter, beam angle lens, or
accessory lens, loosen the setscrew (5/64 hex) and twist
the lens cap back and forth while simultaneously pulling
out. Once the lens cap is removed, twist the top lens 1/4
turn counterclockwise to release the bayonet lock and lift
DO NOT EXCEED 15 VOLTS IN THIS FIXTURE
The LEDs in this product function ideally when the incoming voltage is between 10-15 volts. Voltages outside
of this range may damage LEDs, shorten their lives, and
cause unsatisfactory performance. The use of improper voltage voids the product warranty. Use only a UL
1838 approved power supply such as the Holm PROlink
transformer series. RISK OF FIRE WARNING: DO NOT USE
HOLM FIXTURES WITH ANY STYLE OF TRANSFORMER THAT
EXCEEDS 15 VOLTS ON THE SECONDARY.
Holm does NOT recommend the use of Quick Clip style
connectors or pre-filled wire nuts because they are not
waterproof and can deteriorate,creating resistance
and shorts.
STATEMENT OF LIMITED WARRANTY
Hunter® Industries Incorporated (“Hunter”) warrants
Holm lighting products to be free of defects in materials
or workmanship under normal use for a period of five
(5) years from the date of invoice. See the complete
warranty statement at www.holmlighting.com.
ARCHITECTURAL & LANDSCAPE LIGHTING | holmlighting.com Customer Service 1-844-200-4656
Holm-006-dAlta-US
04/17