Download Hall-Effect IC Applications Guide

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Buck converter wikipedia , lookup

Electric machine wikipedia , lookup

Opto-isolator wikipedia , lookup

Coilgun wikipedia , lookup

Magnetic core wikipedia , lookup

Transcript
Application Information
Hall-Effect IC Applications Guide
Allegro™ MicroSystems uses the latest integrated circuit
technology in combination with the century-old Hall
effect to produce Hall-effect ICs. These are contactless,
magnetically activated switches and sensor ICs with the
potential to simplify and improve electrical and mechanical
systems.
Low-Cost Simplified Switching
Simplified switching is a Hall sensor IC strong point. Halleffect IC switches combine Hall voltage generators, signal
amplifiers, Schmitt trigger circuits, and transistor output
circuits on a single integrated circuit chip. Output is clean,
fast, and switched without bounce (an inherent problem with
mechanical contact switches). A Hall-effect switch typically
operates at up to a 100 kHz repetition rate, and costs less
than many common electromechanical switches.
Efficient, Effective, Low-Cost Linear Sensor ICs
The linear Hall-effect sensor IC detects the motion, position,
or change in field strength of an electromagnet, a permanent magnet, or a ferromagnetic material with an applied
magnetic bias. Energy consumption is very low. The output
is linear and temperature-stable. The sensor IC frequency
response is flat up to approximately 25 kHz.
Sensitive Circuits for Rugged Service
The Hall-effect sensor IC is virtually immune to environmental contaminants and is suitable for use under severe
service conditions. The circuit is very sensitive and provides
reliable, repetitive operation in close-tolerance applications.
The Hall-effect sensor IC can see precisely through dirt and
darkness.
Applications
Applications for Hall-effect ICs include use in ignition systems, speed controls, security systems, alignment controls,
micrometers, mechanical limit switches, computers, printers, disk drives, keyboards, machine tools, key switches,
and pushbutton switches. They are also used as tachometer
pickups, current limit switches, position detectors, selector switches, current sensor ICs, linear potentiometers, and
brushless DC motor commutators.
The Hall Effect: How Does It Work?
The basic Hall element is a small sheet of semiconductor
material, referred to as the Hall element, or active area,
represented in figure 1.
A Hall-effect sensor IC is more efficient and effective than
inductive or optoelectronic sensors, and at a lower cost.
+VCC
–VHALL
+VHALL
Abbreviated Contents
Low-Cost Simplified Switching
Getting Started
Ring Magnets Detailed Discussion
Ferrous Vane Rotary Activators
Enhancement Considerations
Advanced Applications
Glossary
27701-AN, Rev. 2
1
5
14
17
24
36
40
Figure 1. Schematic representation of the active area of a Hall-effect
device, with the Hall element represented by the component marked
with an X.
A constant voltage source, as shown in figure 2, forces a constant bias current, IBIAS , to flow in the semiconductor sheet. The
output takes the form of a voltage, VHALL , measured across the
width of the sheet. In the absence of a magnetic field, VHALL has
a negligible value.
If the biased Hall element is placed in a magnetic field with flux
lines at right angles to the bias current (see figure 3), the voltage output changes in direct proportion to the strength of the
magnetic field. This is the Hall effect, discovered by E. F. Hall in
1879.
IBIAS
IBIAS
0
–
+
Figure 2. VHALL in the absence of a significant magnetic field
–
+
VHALL → V+
Figure 3. Hall effect, induced VHALL, resulting from significant magnetic
flux (green arrows) perpendicular to the bias current flow.
Contents
Low-Cost Simplified Switching
Efficient, Effective, Low-Cost Linear Sensor ICs
Sensitive Circuits for Rugged Service
Applications
The Hall Effect: How Does It Work?
Linear Output Hall-Effect Devices
Digital Output Hall-Effect Switches
Operation
Characteristics and Tolerances
Getting Started
The Analysis
Total Effective Air Gap (TEAG)
Modes Of Operation
Steep Slopes and High Flux Densities
Vane Interruptor Switching
Electrical Interface for Digital Hall Devices
Common Interface Circuits
Rotary Activators for Hall Switches
Ring Magnets for Hall Switch Applications
Bipolar Digital Switches
Digital Latches
Ring Magnets Detailed Discussion
Temperature Effects
An Inexpensive Alternative
Ring Magnet Selection
Ferrous Vane Rotary Activators
27701-AN, Rev. 2
0
VHALL ≈ 0 V
1
1
1
1
1
3
3
3
5
5
5
5
6
6
8
8
8
10
11
12
14
14
14
15
16
17
A Ferrous Vane In Operation
18
Rotor Design
19
Material
19
Vane / Window Widths, Rotor Size
19
Steep Magnetic Slopes for Consistent Switching
19
Small Air Gaps for Steep Slopes
20
Flux Concentrators Pay Dividends
22
Temperature Stability of Operate Points
23
Calculating Dwell Angle and Duty Cycle Variations
23
Effects of Bearing Wear
24
Mounting Also Affects Stability
24
Enhancement Considerations
24
Individual Calibration Techniques
24
Operating Modes: Head-On and Slide-By
24
Operating Mode Enhancements: Compound Magnets 26
Biased Operation
28
Increasing Flux Density by Improving the
Magnetic Circuit
30
Flux Concentrators
31
Feed-Throughs
33
Magnet Selection
33
Advanced Applications
36
Current Limiting and Measuring Current Sensor ICs 36
Multi-Turn Applications
36
Other Applications For Linear Sensor ICs
37
Using Calibrated Devices
39
Glossary
40
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
2
Linear Output Hall-Effect Devices
The output voltage of the basic Hall element is quite small. This
can present problems, especially in an electrically noisy environment. Addition of a stable, high-quality DC amplifier and voltage
regulator to the circuit (see figures 4 and 5) improves the transducer output and allows the device to operate over a wide range
of supply voltages. The modified device provides an easy-to-use
analog output that is linear and proportional to the applied magnetic flux density.
For the most current list of linear output devices from Allegro, go
to http://www.allegromicro.com/en/Products/Categories/Sensors/
linear.asp.
Digital Output Hall-Effect Switches
The addition of a Schmitt-trigger threshold detector with built-in
hysteresis, as shown in figure 6, gives the Hall-effect circuit digital output capabilities. When the applied magnetic flux density
exceeds a certain limit, the trigger provides a clean transition
from off to on without contact bounce. Built-in hysteresis eliminates oscillation (spurious switching of the output) by introducing
a magnetic dead zone in which switch action is disabled after the
threshold value is passed.
An open-collector NPN or N-channel FET (NFET) output transistor added to the circuit (see figure 7) gives the switch digital
logic compatibility. The transistor is a saturated switch that shorts
the output terminal to ground wherever the applied flux density
is higher than the turn-on trip point of the device. The switch is
compatible with all digital families. The output transistor can sink
enough current to directly drive many loads, including relays,
triacs, SCRs, LEDs, and lamps.
The circuit elements in figure 7, fabricated on a monolithic
silicon chip and encapsulated in a small epoxy or ceramic package, are common to all Hall-effect digital switches. Differences
between device types are generally found in specifications such
as magnetic parameters, operating temperature ranges, and temperature coefficients.
Amp.
Figure 4. Hall circuit with amplification of VHALL
Reg.
VCC
Output
Ground
Figure 5. Hall device with voltage regulator and DC amplifier
VCC
Reg.
Output
Ground
Figure 6. Hall circuit with digital output capability
Operation
All Hall-effect devices are activated by a magnetic field. A mount
for the devices and electrical connections must be provided.
Parameters such as load current, environmental conditions, and
supply voltage must fall within the specific limits shown in the
datasheet.
Magnetic fields have two important characteristics: magnetic flux
density, B (essentially, field strength), and magnetic field polarity
(north or south). For Hall-devices, orientation of the field relative
to the device active area also is important. The active area (Hall
element) of Hall devices is embedded on a silicon chip located
parallel to, and slightly inside of, one particular face of the pack-
27701-AN, Rev. 2
VCC
Reg.
Output
Ground
Figure 7. Common circuit elements for Hall switches
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
3
age case. That face is referred to as the branded face because
it is normally the face that is marked with the part number (the
datasheet for each device indicates the active area depth from
the branded face). To optimally operate the switch, the magnetic
flux lines must be oriented to cross perpendicularly through the
branded face (and therefore through the active area), and must
have the correct polarity as it crosses through. Because the active
area is closer to the branded face that it is to the back side of the
case, and is exposed on the branded face side of the chip, using
this orientation produces a cleaner signal.
In the absence of any significant applied magnetic field, most
Hall-effect digital switches are designed to be off (open circuit
at output). They will turn on only if subjected to a magnetic
field that has sufficient flux density and the correct polarity in
the proper orientation. In switches for example, if a south pole
approaching the branded face would cause switching action,
a north pole would have no effect. In usual practice, a close
approach to the branded face of a Hall switch by the south pole
e
lin
ter
n
Ce
Branded face
of package
Active area
N
Mo
S
n
tio
Figure 8. Operation of a Hall-effect device is activated by the motion of a
magnet relative to the plane and centerline of the active area of the device
of a small permanent magnet (see figure 8) causes the output
transistor to turn on.
Transfer characteristic graphs can be used to plot this information. Figures 9 and 10 show output as a function of the magnetic
flux density, B , (measured in gauss, G; 1 G = 0.1 mT) presented
to the Hall element. The magnetic flux density is shown on the
horizontal axis. The digital output of the Hall switch is shown
along the vertical axis. Note that there is an algebraic convention
applied, in which a strengthening south polarity field is indicated
by an increasing positive B value, and a strengthening north
polarity field is indicated by an increasing negative B value. For
example, a +200 B field and a –200 B field are equally strong,
but have opposite polarity (south and north, respectively).
As shown in figure 9, in the absence of an applied magnetic field
(0 G), the switch is off, and the output voltage equals the power
supply (12 V). A permanent magnet south pole is then moved
perpendicularly toward the active area of the device. As the magnet south pole approaches the branded face of the switch, the Hall
element is exposed to increasing positive magnetic flux density.
At some point (240 G in this case), the output transistor turns on,
and the output voltage approaches 0 V. That value of flux density
is called the operate point, BOP . If we continue to increase the
field strength, say to 600 G, nothing more happens. The switch
has already turned on, and stays on.
To turn the switch off, the magnetic flux density must fall to
a value far lower than the 240 G operate point because of the
built-in hysteresis of the device (these types of charts are sometimes referred to as hysteresis charts). For this example we use a
90 G hysteresis, which means the device turns off when the flux
density decreases to 150 G (figure 10). That value of flux density
is called the release point, BRP .
Hysteresis
Off
6
3
On
0
0
100
200
300
400
500
600
9
Operate
Point, BOP
6
Release
Point, BRP
3
On
0
0
100
200
300
400
500
600
Magnetic Flux Density, B (G)
Magnetic Flux Density, B (G)
Figure 9. Transfer characteristics of a Hall switch being activated
(switched on) by the increase in magnetic flux density from an
approaching south pole
27701-AN, Rev. 2
Deivce Switch State
Operate
Point, BOP
Output Voltage (V)
9
Off
12
Deivce Switch State
Output Voltage (V)
12
Figure 10. Transfer characteristics of a Hall switch being deactivated
(switched off) by the decrease in magnetic flux density from an receding
south pole
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
4
To acquire data for this graph, add a power supply and a pull-up
resistor to limit current through the output transistor and enable
the value of the output voltage to approach 0 V (see figure 11).
Characteristics and Tolerances
The exact magnetic flux density values required to turn Hall
switches on and off differ for several reasons, including design
criteria and manufacturing tolerances. Extremes in temperature
will also somewhat affect the operate and release points, which
are the switching thresholds, or switchpoints.
Getting Started
Because the electrical interface is usually straightforward, the
design of a Hall-effect system should begin with the physical
aspects. In position-sensing or motion-sensing applications, the
following questions should be answered:
• How much and what type of motion is there?
• What angular or positional accuracy is required?
• How much space is available for mounting the sensing device
and activating magnet?
For each device type, worst-case magnetic characteristics for the
operate value, the release value, and hysteresis are provided in
the datasheet.
• How much play is there in the moving assembly?
All switches are guaranteed to turn on at or below the maximum
operate point flux density. When the magnetic field is reduced, all
devices will turn off before the flux density drops below the minimum release point value. Each device is guaranteed to have at
least the minimum amount of hysteresis to ensure clean switching
action. This hysteresis ensures that, even if mechanical vibration
or electrical noise is present, the switch output is fast, clean, and
occurs only once per threshold crossing.
• Will the product be a mass-produced assembly, or a limited
number of machines that can be individually adjusted and calibrated?
VCC
RPU
Reg.
Output
V
VOUT ≈ 0 V
Ground
Figure 11. Test circuit for transfer characteristic charts
27701-AN, Rev. 2
• How much mechanical wear can be expected over the lifetime
of the machine?
• What temperature extremes are expected?
A careful analysis will pay big dividends in the long term.
The Analysis
The field strength of the magnet should be investigated. The
strength of the field will be greatest at the pole face, and will
decrease with increasing distance from the magnet. The strength
of the magnetic field can be measured with a gaussmeter or a
calibrated linear Hall sensor IC, and is a function of distance
along the intended line of travel of the magnet. Hall device specifications (sensitivity in mV/G for a linear device, or operate and
release points in gauss for a digital device) can be used to determine the critical distances for a particular magnet and type of
motion. Note that these field strength plots are not linear, and that
the shape of the flux density curve depends greatly upon magnet
shape, the magnetic circuit, and the path traveled by the magnet.
Total Effective Air Gap (TEAG)
Total effective air gap (TEAG), is the sum of the active area
depth (AAD, the depth of the Hall element below the branded
face of the device) and the air gap (AG, the distance between the
package branded surface and the magnet or target surface). The
AG is a mechanical clearance which should be as small as possible, consistent with dimensional tolerances of the magnet, bearing tolerances, bearing wear, and temperature effects on the Hall
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
5
switch mounting bracket. Figure 12A is a graph of flux density as
a function of TEAG, and illustrates the considerable increase in
flux density at the sensor IC provided by a thinner package (the
Allegro UA package has an AAD of about 0.50 mm). The actual
gain depends predominantly on the characteristic slope of the flux
density for the particular magnet used in the application. Note
that the chart also shows the effect on flux density of other physical factors, such as package contribution from the device itself,
and from any overmolding or protective covering of the sensor
assembly in the application.
Modes Of Operation
Even with a simple bar or rod magnet, there are several possible
paths for motion. The magnetic pole could move perpendicularly
straight at the branded face of the Hall device. This is called the
head-on mode of operation. The curve in figure 12B illustrates
typical flux density (in gauss) as a function of TEAG for a cylindrical magnet.
The head-on mode is simple, works well, and is relatively
insensitive to lateral motion. The designer should be aware that
overextension of the mechanism could cause physical damage to
the epoxy package of the Hall device if collision occurs.
Active Area Depth (AAD)
Magnetic Flux Density, B (G)
400
TEAG
AG
AAD
300
N
Total Package
Contribution
200
S
Active
area
Magnet
Branded
face
100
Device
0
0
1.3
2.5
3.8
Total Effective Air Gap, TEAG (mm)
Figure 12A. Definition of total effective air gap, active area depth, and
demonstration of the effects of the package itself on magnetic signal
strength (for specifications of the magnet used for this data, see figure 25)
27701-AN, Rev. 2
A second configuration is moving the magnet from side to side
across the Hall device, parallel to the branded face. This is
referred to as the slide-by mode of operation, as illustrated in
figure 13. Note that now the distance plotted on the horizontal axis of the chart is not total effective air gap, but rather the
perpendicular distance from the centerline of the magnet to the
centerline of the active area. Air gap is specified because of its
obvious mechanical importance, but bear in mind that to do any
calculations involving flux density, the package contribution must
be added and the TEAG used, as before. The slide-by mode is
commonly used to avoid contact if overextension of the mechanism is likely. The use of strong magnets and/or ferrous flux concentrators in well-designed slide-by magnetic circuits provides
better sensing precision, with shorter travel of the magnet, than
the head-on mode.
Magnet manufacturers generally can provide head-on flux density
curves for their magnets, but they often do not characterize them
for slide-by operation, possibly because different air gap choices
lead to an infinite number of these curves. However, after an air
gap is chosen, the readily available head-on magnetic curves can
be used to find the peak flux density (a single point) in the slideby application by noting the value at the total effective air gap.
Steep Slopes and High Flux Densities
For linear Hall devices, greater flux change for a given displacement gives greater output; clearly an advantage. The same
property is desirable for digital Hall devices, but for more subtle
reasons. To achieve consistent switching action in a given application, the Hall device must switch on and off at the same positions relative to the magnet.
To illustrate this concept, consider the flux density curves from
two different magnet configurations, in figure 14. With an operate-point flux density of 200 G, a digital Hall-effect device would
turn on at a distance of approximately 3.6 mm in either case. If
manufacturing tolerances or temperature effects shifted the operate point to 300 G, notice that for curve A (steep slope) there is
very little change in the distance at which switching occurs. In
the case of curve B, the change is considerable. The release point
(not shown) would be affected in much the same way. The basic
principles illustrated in this example can be modified to include
mechanism and device specification tolerances and can be used
for worse-case design analysis. Examples of this procedure are
shown in later sections.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
6
G
TEA
Magnetic Flux Density, B (G)
1000
S
N
Mo
800
n
tio
Ø5.4 mm
TEAG
4.8 mm
600
400
N
200
S
0
0
1.3
2.5
3.8
5.1
6.4
7.6
8.9 10.2
Alinco 8 Magnet
Total Effective Air Gap, TEAG (mm)
Figure 12B. Demonstration of head-on mode of operation
G
TEA
S
N
Magnetic Flux Density, B (G)
1000
Mo
D
tio
n
800
Ø5.4 mm
TEAG
4.8 mm
600
400
N
200
S
0
0
1.3
2.5
3.8
5.1
6.4
7.6
8.9 10.2
Alinco 8 Magnet
Distance Between Centerlines of Magnet
and Hall Element, D (mm)
Figure 13. Demonstration of slide-by mode of operation, showing effect of changes
in displacement between the centerlines of the magnet and the active area
G
TEA
N
Magnetic Flux Density, B (G)
1000
S
Mo
tio
n
800
Ø5.4 mm
4.8 mm
600
TEAG
(A)TEAG = 1.3 mm
400
N
200
S
(B)TEAG = 2.5 mm
0
0
1.3 2.5 3.8 5.1 6.4 7.6 8.9 10.2
Distance Between Centerlines of Magnet
and Hall Element, D (mm)
Alinco 8 Magnet
Figure 14. Example of slide-by mode of operation, comparing the effects of two
different Total Effective Air Gaps
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
7
Vane Interruptor Switching
In this mode, the activating magnet and the Hall device are
mounted on a single rigid assembly with a small air gap between
them. In this position, the Hall device is held in the On state by
the activating magnet. If a ferromagnetic plate, or vane, is placed
between the magnet and the Hall device, as shown in figure 15,
the vane forms a magnetic shunt that distorts the flux field away
from the Hall device.
Use of a movable vane is a practical way to switch a Hall device.
The Hall device and magnet can be molded together as a unit,
thereby eliminating alignment problems, to produce an extremely
rugged switching assembly. The ferrous vane or vanes that interrupt the flux could have linear motion, or rotational motion, as
in an automotive distributor. Ferrous vane assemblies, due to the
steep flux density/ distance curves that can be achieved, are often
used where precision switching over a large temperature range is
required.
The ferrous vane can be made in many configurations, as shown
in figure 16. With a linear vane similar to that of figure 16B, it
is possible to repeatedly sense position within 0.05 mm over a
125°C temperature range.
Concentrator
N
S
When the transistor is off, there is a small output leakage current
(typically a few nanoamperes) that usually can be ignored, and
a maximum (breakdown) output voltage (usually 24 V), which
must not be exceeded.
When the transistor is on, the output is shorted to the circuit
common. The current flowing through the switch must be externally limited to less than a maximum value (usually 20 mA) to
prevent damage. The voltage drop across the switch, VCE(sat)) ,
will increase for higher values of output current. You must make
certain this voltage is compatible with the Off state, or logic low,
voltage of the circuit you wish to control.
Hall devices switch very rapidly, with typical rise and fall times
in the 400 ns range. This is rarely critical, because switching
times are almost universally controlled by much slower mechanical parts.
Common Interface Circuits
Figure 17 illustrates a simplified schematic symbol for Hall digital switches. It will make further explanation easier to follow.
Interfacing to digital logic integrated circuits usually requires
only an appropriate power supply and pull-up resistor.
Vane
Magnetic flux
S
Electrical Interface for Digital Hall Devices
The output stage of a digital Hall switch is simply an open-collector NPN transistor (see figure 17). The rules for use are the same
as those for any similar switching transistor.
N
With current-sinking logic families, such as DTL or the popular
7400 TTL series (figure 18A), the Hall switch has only to sink
one unit-load of current to the circuit common when it turns on
(1.6 mA maximum for TTL). In the case of CMOS gates (fig-
Magnet
Hall device
Figure 15. Demonstration of vane interruptor operation: (left) normal
magnetic flux path without vane interruption, (right) vane shunting
magnetic flux
Output
VCC
Common
Figure 16. Typical configurations for vane interruptors: (A) disk, (B), linear,
and (C) cup
27701-AN, Rev. 2
Figure 17. Hall-effect device with open-collector output stage (illustration
of Hall circuit simplified for clarity in later figures)
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
8
ure 18B), with the exception of switching transients, the only
current that flows is through the pull-up resistor (about 0.2 mA in
this case).
Loads that require sinking currents up to 20 mA can be driven
directly by the Hall switch.
Sinking more current than 20 mA requires a current amplifier. For
example, if a certain load to be switched requires 4 A and must
turn on when the activating magnet approaches, the circuit shown
in figure 20 could be used.
A good example is a light-emitting diode (LED) indicator that
requires only a resistor to limit current to an appropriate value. If
the LED drops 1.4 V at a current of 20 mA, the resistor required
for use with a 12 V power supply can be calculated as:
When the Hall switch is off (insufficient magnetic flux to operate), about 12 mA of base current flows through the 1 kΩ resistor
to the Q1 transistor, thereby saturating it and shorting the base
of Q2 to ground, which keeps the load off. When a magnet is
brought near the Hall switch, it turns on, shorting the base of Q1
to ground and turning it off. This allows:
(12 V - 1.4 V) / 0.02 A = 530 Ω
12 V / 56 Ω = 210 mA
The nearest standard value is 560 Ω, resulting in the circuit of
figure 19.
of base current to flow to Q2, which is enough to saturate it for
any load current of 4 A or less.
VCC = +10 V
VCC = +5 V
47 kΩ
10 kΩ
CMOS
TTL
Output
Output
Common
Common
Figure 18A. TTL logic interface
Figure 18B. CMOS logic interface
VCC = +12 V
VCC = +12 V
Load
560 Ω
1 kΩ
56 Ω
Q2
Q1
Output
Output
Common
Common
Figure 19. Example of small (≤20 mA) sinking current load being driven
directly
27701-AN, Rev. 2
Figure 20. Example of driving a moderate (>20 mA) sinking current load
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
9
The Hall switch can source current to a load in its On or Off state,
by configuring an external transistor. For example, figure 21 is an
example of sourcing current in the On state, in an application to
turn on a 115 or 230 VAC load using a relay.
A typical relay with a 12 V coil requires a current drive between
40 and 60 mA (this varies from relay to relay) to trigger it to the
On state, in which the high voltage contacts are closed. This
could be done with an adequately sized PNP transistor.
When the Hall switch is turned on, 9 mA of base current flows
out of the base of the PNP transistor, thereby saturating it and
allowing it to drive enough current to trigger the relay. When the
Hall switch is off, no base current flows from the PNP, which
turns it off and prevents coil current from passing to the relay.
The 4.7 kΩ resistor acts as a pull-up on the PNP base to keep
it turned off when the Hall switch is disabled. A freewheeling
diode is placed across the relay coils in order to protect the PNP
collector from switching transients that can happen as the result
of abruptly turning off the PNP. Note that the +12 V supply common is isolated from the neutral line of the AC line. This presents
a relatively safe way to switch high voltage AC loads with low
voltage DC circuits. As always, be very careful when dealing
with AC line voltage and take the proper safety precautions.
Rotary Activators for Hall Switches
A frequent application involves the use of Hall switches to
generate a digital output proportional to velocity, displacement,
or position of a rotating shaft. The activating magnetic field for
rotary applications can be supplied in either of two ways:
(a) Magnetic rotor assembly
The activating magnets are fixed on the shaft and the stationary Hall switch is activated with each pass of a magnetic south
pole (figure 22, panel A). If several activations per revolution are
required, rotors can sometimes be made inexpensively by molding or cutting plastic or rubber magnetic material (see the An
Inexpensive Alternative section).
VCC = +12 V
115 VAC
4.7 kΩ
1.2 kΩ
Load
Output
40 mA
Common
Figure 21. Example of a relay-driving application, sourcing current in the Hall device Off state
Motion
Motion
Magnets
Magnet
Figure 22. Typical configurations for rotors: (A) magnetic, and (B) ferrous vane
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
10
Ring magnets also can be used. Ring magnets are commercially
available disc-shaped magnets with poles spaced around the
circumference. They operate Hall switches dependably and at
reasonable costs. Ring magnets do have limitations:
• The accuracy of pole placement (usually within 2 or 3 degrees).
• Uniformity of pole strength ( ±5%, or worse).
These limitations must be considered in applications requiring
precision switching.
(b) Ferrous vane rotor assembly
In this configuration, both the Hall switch and the magnet are
stationary (figure 22, panel B). The rotor interrupts and shunts the
flux (see figure 15) with the passing of each ferrous vane.
Vane switches tend to be a little more expensive than ring magnets, but because the dimensions and configuration of the ferrous
vanes can be carefully controlled, they are often used in applications requiring precise switching or duty cycle control.
Properly designed vane switches can have very steep flux density
curves, yielding precise and stable switching action over a wide
temperature range.
Ring Magnets for Hall Switch Applications
Ring magnets suitable for use with Hall switches are readily
available from magnet vendors in a variety of different materiPhysical
Models
B
S
N
N
N
Schematic
Views
S
S
N
N
S
Figure 23. Common ring magnet types: (A) radial, and (B) axial; the
schematic views are used in alignment diagrams later in this text
27701-AN, Rev. 2
Materials most commonly used are various Alnicos, Ceramic 1,
and barium ferrite in a rubber or plastic matrix material (see
table 4). Manufacturers usually have stock sizes with a choice of
the number of pole pairs. Custom configurations are also available at a higher cost.
Alnico is a name given to a number of aluminum nickel-cobalt
alloys that have a fairly wide range of magnetic properties. In
general, Alnico ring magnets have the highest flux densities, the
smallest changes in field strength with changes in temperature,
and the highest cost. They are generally too hard to shape except
by grinding and are fairly brittle, which complicates the mounting
of bearings or arbor.
Ceramic 1 ring magnets (trade names Indox, Lodex) have somewhat lower flux densities (field strength) than the Alnicos, and
their field strength changes more with temperature. However,
they are considerably lower in cost and are highly resistant to
demagnetization by external magnetic fields. The ceramic material is resistant to most chemicals and has high electrical resistivity. Like Alnico, they can withstand temperatures well above that
of Hall switches and other semiconductors, and must be ground if
reshaping or trimming is necessary. They may require a support
arbor to reduce mechanical stress.
The rubber and plastic barium ferrite ring magnets are roughly
comparable to Ceramic 1 in cost, flux density, and temperature
coefficient, but are soft enough to shape using conventional
methods. It is also possible to mold or press them onto a shaft for
some applications. They do have temperature range limitations,
from 70°C to 150°C, depending on the particular material, and
their field strength changes more with temperature than Alnico or
Ceramic 1.
N
A
als and configurations. The poles may be oriented either radially
(figure 23, panel A) or axially (figure 23, panel B) with up to 20
pole-pairs on a 25-mm diameter ring. For a given size and pole
count, ring magnets with axial poles have somewhat higher flux
densities.
Regardless of material, ring magnets have limitations on the
accuracy of pole placement and uniformity of pole strength
which, in turn, limit the precision of the output waveform. Evaluations have shown that pole placement in rubber, plastic, and
ceramic magnets usually falls within ±2° or ±3° of target, but
±5° errors have been measured. Variations of flux density from
pole to pole will commonly be ±5%, although variations of up to
±30% have been observed.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
11
Figure 24 is a graph of magnetic flux density as a function of
angular position for a typical 4 pole-pair ceramic ring magnet,
25.4 mm in diameter, with a total effective air gap, TEAG, of
1.7 mm (1.3 mm clearance plus 0.4 mm package contribution). It
shows quite clearly both the errors in pole placement and variations of strength from pole to pole.
A frequent concern with ring magnets is ensuring sufficient flux
density for reliable switching. There is a trade-off between the
quantity of pole-pairs and the flux density for rings of a given
size. Thus, rings with a greater quantity of poles have lower flux
densities. It is important that the TEAG be kept to a minimum,
because flux density at the Hall active area decreases by about
200 to 240 G per millimeter for many common ring magnets.
This is clearly shown in figure 25, a graph of flux density at a
pole as a function of TEAG for a typical 20–pole-pair plastic ring
magnet.
Bipolar Digital Switches
A bipolar switch has consistent hysteresis, but individual units
have switchpoints that occur in either relatively more positive
or more negative ranges. These devices find application where
closely-spaced, alternating north and south poles are used (such
as ring magnets), resulting in minimal magnetic signal amplitude,
ΔB, but the alternation of magnetic field polarity ensures switching, and the consistent hysteresis ensures periodicity.
Magnetic Flux Density, B (G)
1000
800
N
S
N
180°
400
S
N
600
S
200
N
0
-200
0°
S
TEAG =
1.7 mm
-400
-600
-800
25.4 mm
-1000
0
90
180
270
360
Ceramic, 4 Pole Pairs
Axial Poles
Magnet Rotation (deg.)
Figure 24. Magnetic flux characteristic of a ring magnet
S
N S NS N S N
SN S S
SN
Package
contribution
N
300
S
N
N S NS
S S
N
NS
200
SN
N
S
N
SN
N
N
Magnetic Flux Density, B (G)
400
SN S N S
5.1 mm
TEAG
100
0
0
3.2 mm
25.4 mm
1.3
2.5
3.8
Total Effective Air Gap, TEAG (mm)
Plastic 1, 20 Pole Pairs
Radial Poles
Figure 25. Demonstration of the effect of narrow pole pitch on magnetic signal strength
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
12
An example of a bipolar switch would be a device with a maximum operate point, BOP(max), of 45 G, a minimum release point,
BRP(min), of –40 G, and a minimum hysteresis, BHYS(min), of 15
G. However, the minimum operate point, BOP(min), could be as
low as –25 G, and the maximum release point, BRP(max), could
be as high as 30 G. Figure 26A shows these characteristics for
units of a hypothetical device with those switchpoints. At the top
of figure 26A, trace “Minimum ΔB” demonstrates how small
an amplitude can result in reliable switching. A “unipolar mode”
unit would have switchpoints entirely in the positive (south)
range, a “negative unipolar mode” unit would have switchpoints
entirely in the negative (north) range, and a “Latch mode” unit
would have switchpoints that straddle the south and north ranges
(behaving like a digital latch, a Hall device type described in the
next section). As can be seen in the VOUT traces at the bottom of
figure 26A, for each of these possibilities, the duty cycle of the
output is different from each other, but consistent switching at
each pole alternation is reliable.
south poles are present in an alternating pattern. The release point
flux density becomes less important because if the Hall switch
has not turned off when the flux density approaches zero (south
pole has passed), it will certainly turn off when the following north pole causes flux density to go negative. Bipolar Hall
switches take advantage of this extra margin in release-point flux
values to achieve lower operate-point flux densities, a definite
advantage in ring magnet applications.
In applications previously discussed for other types of devices,
the Hall switch was operated (turned on) by the approach of a
magnetic south pole (positive flux). When the south pole was
removed (magnetic flux density approached zero), the Hall
switch had to release (turn off). On ring magnets, both north and
• Operating temperature range of –20°C to 85°C,
B
7.5
–7.5
Magnetic Flux Density, B (G)
VOUT
45
30
7.5
–7.5
–25
–40
A current list of Allegro bipolar switches can be found at
http://www.allegromicro.com/en/Products/Categories/Sensors/
bipolar.asp.
Bipolar Digital Switch Design Example
Given:
• Bipolar Hall switch in Allegro UA package: Active Area Depth,
AAD, (and package contribution) of 0.50 mm,
• Air Gap, AG, (necessary mechanical clearance) of 0.76 mm,
• Maximum operate point, BOP , of 200 G (from –20°C to 85°C),
and
• Minimum release point, BRP , of –200 G (from –20°C to 85°C).
BOP
BHYS(min)
BRP
Minimum ∆B
Minimum ∆B
BOP(max)
BHYS(min) Unipolar mode unit
BRP(max)
BOP
BHYS(min) Latch mode unit
BRP
BOP(min)
BHYS(min) Negative unipolar mode unit
BRP(min)
VOUT
Unipolar mode unit
VOUT
Latch mode unit
VOUT
Negative unipolar mode unit
Figure 26A. Demonstration of possible switchpoint ranges for a bipolar switch, for use with low magnetic flux amplitude, narrow pitch
alternating pole targets
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
13
1. Find the total effective air gap, TEAG:
Ring Magnets Detailed Discussion
▫ TEAG = AG + AAD
▫ TEAG = 0.76 mm + 0.50 mm = 1.26 mm
2. Determine the necessary flux density, B, sufficient to operate
the Hall switch, plus 40%.
To operate the Hall switch, the magnet must supply a minimum
of ±200 G, at a distance of 1.26 mm, over the entire operating
temperature range. Good design practice requires the addition of
extra flux to provide some margin for aging, mechanical wear,
and other imponderables. If we add a pad of 100 G—a reasonable
number—the magnet required must supply ±300 G at a distance
of 1.26 mm, over the entire operating temperature range.
Digital Latches
Unlike bipolar switches, which may release with a south pole or
north pole, the latch (which is inherently bipolar) offers a more
precise control of the operate and release parameters. This Hall
integrated circuit has been designed to operate (turn on) with a
south pole only. It will then remain on when the south pole has
been removed. In order to have the bipolar latch release (turn
off), it must be presented with a north magnetic pole. This alternating south pole-north pole operation, when properly designed,
produces a duty cycle approaching 50%, as shown in figure 26B.
Magnetic Flux Density, B (G)
Allegro offers a wide selection of Hall effect latches designed
specifically for applications requiring a tightly controlled duty
cycle, such as in brushless DC motor commutation. Latches can
also be found in applications such as shaft encoders, speedometer
elements, and tachometer sensors. For a current list of Allegro
latching sensor ICs visit http://www.allegromicro.com/en/Products/Categories/Sensors/latches.asp.
150
–150
BOP(max)
BRP(min)
VOUT
Figure 26B. Demonstration of the bipolar latch characteristic, for use in
precise duty cycle control, alternating pole targets
27701-AN, Rev. 2
Temperature Effects
Unfortunately, magnet strength is affected by temperature to
some extent. Temperature coefficients of some common magnetic
materials are given in table 1.
Table 1. Temperature Effects
Material
Temperature Coefficient
Rubber/plastic
–0.2% to –0.3% per °C
Ceramic 1
–0.15% to –0.2% per °C
Alnico 2, 5
–0.02% to –0.03% per °C
Alnico 8
±0.01% per °C
If we are considering a ceramic ring magnet with a worst-case
temperature coefficient of –0.2%/°C, we must add some extra
flux density to the requirement at room temperature to ensure that
we still have 300 G per south pole at +85°C. This amount is:
[(85°C – 25°C) × 0.2%/°C] 300 G = 36 G
Thus, the flux density that will ensure that the Hall switch will
operate over temperature is 300 G + 36 G = 336 G per south pole
at +25°C.
Follow the same procedure for the north pole requirements. If the
magnet will supply 300 G per south pole and –300 G per north
pole at +85°C, it will supply even more flux density per north
pole at –20°C because of the negative temperature coefficient.
In applications where temperature conditions are more severe,
Alnico magnets are considerably better than the ceramic magnets
we considered. It is also possible to order custom Hall switches
with specifications tailored to your application. For example, you
can specify a range of operate and release points at a particular
temperature, with temperature coefficients for operate and release
points, if that is better suited to your application. On a custom
basis, Hall switches are available with operate and release point
temperature coefficients of less than 0.3 G/°C, and with operate
point flux densities of less than 100 G.
If you intend to use a low-cost, low flux density ring magnet,
then a device in the Allegro UA package (1.55 mm overall
thickness) would be a good choice. The AAD is 0.50 mm, which
results in a significant improvement in peak flux density from a
magnet, as shown in figure 25.
If the rotor drive can withstand an increased torque requirement, consider a ferrous flux concentrator. Flux density can be
increased by 10% to 40% in this manner. A mild steel concentrator of 0.8 mm thickness, having the same dimensions as and
cemented to, the back face of the Hall device case, will increase
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
14
flux density by about 10%. A return path of mild steel from the
back side of the device to the adjacent poles can add even more.
Often the functions of mounting bracket and flux concentrator
can be combined (see figure 57 for an example).
An Inexpensive Alternative
Innovative design can produce surprisingly good results. Rubber
and plastic magnet stock comes in sheets. One side of the sheet is
magnetic north; the other side is south. This material is relatively
inexpensive and can easily be stamped or die-cut into various
shapes.
These properties prompted one designer to fabricate an inexpensive magnetic rotor assembly that worked very well. The rubber
magnet stock was die-cut into a star-shaped rotor form, as shown
in figure 27. A nylon bushing formed a bearing, as shown in
figure 28.
Finally, a thin mild-steel backing plate was mounted to the back
of the assembly to give mechanical strength and to help conduct
the flux back from the north poles on the opposite side. This
actually served to form apparent north poles between the teeth;
the measured flux between south pole teeth is negative. Figure 29
shows the completed magnetic rotor assembly, essentially a ring
magnet with axial poles.
The Hall switch was mounted with its active surface close to the
top of the rotor assembly, facing the marked poles. There is some
versatility in this approach, as asymmetrical poles can be used to
fabricate a rotor that will allow trimmable on time and thus work
as a timing cam. Figure 30 illustrates a cam timer adjusted to
180° on and 180° off.
Figure 27. Demonstration of rubber magnet stock layout for inexpensive
ring magnet
Figure 28. Demonstration of nylon bushing for inexpensive ring magnet
Figure 29. Demonstration of assembled inexpensive ring magnet
Figure 30. Demonstration of adjustment of ring magnet to 180° on and
180° off
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
15
▫ Flux density at a given TEAG (remember to add the Hall
switch package contribution to the clearance figure)
Ring Magnet Selection
When you discuss your application with a magnet vendor, the following items should be considered:
▫ Magnetic temperature coefficient
• Environmental Factors
• Mechanical factors
▫ Tolerance of the material to the working environment (temperature, chemical solvents, electric potentials)
▫ Dimensions and tolerances
▫ Mounting hole type and maximum eccentricity
Flux density curves from several typical ring magnets are
included in the following figures, to present an idea of what can
be expected from various sizes and materials. Figure 31 shows
the curve for a ring similar in size and material to that of figure
25, but with 10 pole-pairs instead of 20 (note increased flux density values). Figure 32 shows the curve from a single pole-pair,
Alnico 8 ring.
▫ Rotational speed
▫ Mechanical support required
▫ Coefficient of expansion
• Magnetic Factors
▫ Poles: number, orientation, and placement accuracy
S N S N
S
N
300
N
S N
S
S
N
S
200
N
S
N
Magnetic Flux Density, B (G)
400
S
N
N
S
5.1 mm
TEAG
100
3.2 mm
25.4 mm
0
0
1.3
2.5
3.8
Plastic 1, 10 Pole Pairs
Radial Poles
Total Effective Air Gap, TEAG (mm)
Figure 31. Example of magnetic flux density versus air gap for Plastic 1 ring magnet
300
S
N
Magnetic Flux Density, B (G)
400
200
TEAG
100
5.1 mm
3.2 mm
0
19.1 mm
0
1.3
2.5
3.8
Total Effective Air Gap, TEAG (mm)
Alinco 8, 1 Pole Pair
Axial Poles
Figure 32. Example of magnetic flux density versus air gap for Alinco 8 ring magnet
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
16
Figure 33 shows the curve from a three-pole-pair Ceramic 1 ring.
Figure 34 shows the curves from a four-pole-pair Ceramic 1 ring,
with and without a ferrous flux concentrator. Incoming inspection
of ring magnets is always advisable. You can ensure the magnets
are within the agreed upon magnetic specifications by making
measurements with a commercial gaussmeter, or a calibrated linear Hall device mounted in a convenient test fixture. Calibrated
Hall devices and technical assistance are available from Allegro.
Ferrous Vane Rotary Activators
A ferrous vane rotor assembly is the alternative to magnetic
rotors for rotary Hall switch applications. As shown previously,
a single magnet will hold a Hall switch on except when one of
the rotor vanes interrupts the flux path and shunts the flux path
away from the Hall switch. The use of a single stationary magnet
allows very precise switching by eliminating ring magnet variations, placement, and strength. Unlike the evenly spaced poles
on ring magnets, the width of rotor vanes can easily be varied. It
is possible to vary the Hall switch off and on times, which gives
the designer control over the duty cycle of the output waveform.
Ferrous-vane rotors are a good choice where precise switching
is desired over a wide range of temperatures. As the vane passes
between magnet and Hall switch, progressively more flux will
be blocked or shunted. Small variations in lateral position have a
very small effect on the transition point.
N
S
S
300
N
Magnetic Flux Density, B (G)
400
200
S
100
N
6.4 mm
0
0
1.3
2.5
3.8
Total Effective Air Gap, TEAG (mm)
TEAG
19.1 mm
44.5 mm
Ceramic 1, 3 Pole Pairs
Radial Poles
Figure 33. Example of magnetic flux density versus air gap for Ceramic 1 ring magnet
S
N
N
300
S
With flux
concentrator
S
200
N
N
Magnetic Flux Density, B (G)
400
S
Without flux
concentrator
100
6.4 mm
TEAG
6.4 mm
19.1 mm
0
0
1.3
2.5
Concentrator
Ø3.2 mm
L = 6.4 mm
3.8
Total Effective Air Gap, TEAG (mm)
Ceramic 1, 4 Pole Pairs
Radial Poles
Figure 34. Example of magnetic flux density versus air gap for Ceramic 1 ring magnet, showing comparative results with a cylindrical ferrous flux
concentrator attached to back side of a Hall device case
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
17
A Ferrous Vane In Operation
Figure 35 combines views of a ferrous-vane magnet/Hall switch
system with the graph of flux density as a function of vane travel
produced by this system. Note that the drawings and the graph
are vertically aligned along the horizontal axis. Position is measured from the leading edge of the vane to the centerline of the
magnet/Hall device.
nears the magnet, the shunting effect of the vane causes the flux
density to decrease in a nearly linear fashion. When the vane
passes the device centerline, the magnet is covered by the vane
and flux density is at a minimum. As the vane travels on, it starts
to uncover the magnet. This allows the flux to increase to its
original value. After that, additional vane travel has no further
influence on flux density at the Hall element.
Initially, when the vane is located entirely to the left of the
magnet, the vane has no effect and the flux density at the element is at a maximum of 800 G. As the leading edge of the vane
A Hall switch located in the position of the sensor IC would
initially be on because of the presence of the magnetic field.
Somewhere in the linearly decreasing region, the flux would fall
below the release point, and the Hall switch would turn off. It
Cup target
Magnet
Vane
(22.5°)
Device
Vane
Magnet
N
S
TEAG
Device
Case
Hall
Element
Top View
Side View
Magnetic Flux Density, B (G)
1000
800
600
Effective Vane
Width (24°)
400
200
0
60
Release
Point, BRP
Operate
Point, BOP
Actual Vane
Width (22.5°)
40
20
0
20
Vane Travel (deg.)
40
60
Figure 35. Rotary single-vane assembly and characteristic magnetic profile, using a samarium cobalt
magnet and Ø65 mm ferrous cup target (150 G/deg.)
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
18
would remain off until the increasing flux reaches the operate
point for that particular Hall switch. Recall that the operate point
flux density is greater than the release point flux density by the
amount of the hysteresis for that particular Hall switch.
The interval during which the Hall switch remains off (from the
time of the Hall switch release point until the next operate point)
is determined by the actual width of the vane and the steepness
of the magnetic slope, as well as by the operate and release point
flux density (switchpoint threshold) values for the Hall switch.
This interval is called the effective vane width, and it is always
somewhat greater than the physical vane width.
Rotor Design
Two commonly used rotor configurations are the disk and the
cup, as shown in figure 36.
designed. Firing point stability may be held to ±0.005 distributor
degrees per degree Celsius in a well-designed system.
Material
Vanes are made of a low-carbon steel to minimize residual magnetism and to give good shunting action. The vane thickness is
chosen to avoid magnetic saturation for the value of flux density
it must shunt. Vane material is usually between 0.8 and 1.5 mm
thick.
Vane / Window Widths, Rotor Size
Generally, the smallest vanes and windows on a rotor should be
at least one and one-half times the width of the magnet pole, to
provide adequate shunting action and to maintain sufficient differential between the off and on values of flux density.
The disk is easily fabricated and, hence, is often used for lowvolume applications such as machine control. Axial movement
of the rotor must be considered. Vane-activated switches tolerate
this quite well, but the rotor must not hit the magnet or the Hall
switch.
In table 2, the maximum flux density (obtained with window centered over the magnet, the minimum flux density (vane centered
over the magnet), and the difference between the two values are
tabulated for three cases:
Cup rotors are somewhat more difficult to fabricate and so are
more expensive, but dealing with a single radial distance simplifies calculations and allows precise control of the output waveforms. For cup rotors, radial bearing wear or play is the significant factor in determining the clearances, while axial play is relatively unimportant. Cup rotors have been used very successfully
in automotive ignition systems. The dwell range is determined
by the ratio of the vane-to-window widths when the rotor is
• Vane and window width one and one-half times magnet pole
width
Figure 36. Illustration of rotor styles: (left) disk and (right) cup with multiple
vanes
• Vane and window width the same as magnet pole width
• Vane and window width two times the magnet pole width
In each sample, the magnet is 6.4 × 6.4 × 3.2 mm samarium
cobalt, the air gap is 0.3 mm, and the rotor vanes are made of
1 mm mild-steel stock.
If a small rotor with many windows and vanes is required, a
miniature rare-earth magnet must be used to ensure sufficient
flux density for reliable operation. For example, a 2.5 mm cubical
samarium cobalt magnet makes it practical to fabricate a 31.8 mm
diameter rotor with as many as 10 windows and vanes. With
fewer vanes, even further size reduction is possible.
Steep Magnetic Slopes for Consistent Switching
A graph of flux density versus vane travel, for most common
vane configurations, is very nearly linear in the transition regions
(see figure 35). The Hall switch operate and release points fall in
these linear transition regions, and it is easily seen that if these
values change, the position of the vane which causes the switch-
Table 2. Magnetic Flux Density, B, at Various Vane and Window Positions and Relative Dimensions
Position Relative to Magent Centerline
Window centered
Vane and Window Width Factor Relative to Magnet Pole Face
1.0 ×
1.5 ×
2.0 ×
630 G
713 G
726 G
Vane centered
180 G
100 G
80 G
Window centered - Vane centered
450 G
613 G
646 G
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
19
ing must change also. Figure 37 shows the flux density as a
function of vane position for two different magnetic circuits. In
one case, the magnetic slope is 98 G/mm. In the second case, it is
107 G/mm.
If the 98 G/mm system is used with a Hall switch known to
have an operate point flux density of 300 G at 25°C, the device
would switch on when the vane is 2.2 mm past the center of the
window, at this temperature. If the Hall switch operate point
went up to 400 G at a temperature of 125°C (this represents Hall
switch temperature coefficient of 1 G/°C), the vane must move
to 3.1 mm past center, a change in switching position of about
1 mm. If the same Hall switch is used in the second system having the 107 G/ mm slope, the operate point would shift only about
0.5 mm, or half as much, because the slope is twice as steep.
Slopes in typical vane systems range from 40 G/mm to
590 G/ mm, and are affected by magnet type and size, the magnetic circuit, and the total effective air gap. It is interesting to note
that, although slide-by operation can give very steep slopes, the
transition point is much affected by lateral motion (change in air
gap); therefore, vanes are often preferred for applications involving play or bearing wear.
Small Air Gaps for Steep Slopes
The air gap should be as small as the mechanical system allows.
Factors to be considered are:
• Vane material thickness and vane radius
• Maximum eccentricity (for cup vanes)
• Bearing tolerance and wear
• Change in air gap with temperature due to mounting considerations
In figure 38, two different samarium cobalt magnets are used in
a vane system to illustrate the effects of changes in air gap and
magnet size. Note that only the falling transition region is shown
(the rising transition region would be symmetrical). The distances
on the horizontal axis have been measured from the leading edge
of the vane.
The term “air gap” as used in figure 38 is not the total effective
air gap; but is simply the distance from the face of the magnet
to the surface of the Hall switch. It does not include the package
contribution. The Allegro U package is often used in ferrous vane
applications because it has a shallow active area depth.
Magnetic Flux Density, B (G)
1000
800
Magnetic slope =
107 G/mm
600
Magnetic slope =
98 G/mm
400
200
1.0 mm
0.5 mm
0
-7.6
-5.1
-2.5
0
2.5
5.1
7.6
Vane Position (mm)
Figure 37. Comparison of two applications, for flux density versus vane travel, showing linearity in the transition regions, despite varying rates
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
20
1000
4 3 2
900
Magnetic Flux Density, B (G)
800
1
5
6
7
700
8
600
500
Concentrator
Device
Vane
Magnet
400
CL
Concentrator
(if used)
300
Device
Branded
Face
D
200
Vane
100
Air Gap
S
N
Magnet
0
-5.1
-3.8
-2.5
-1.3
0
1.3
Distance from Vane Leading Edge to Device/Magnet Centerline, D (mm)
(Only leading edge curves shown; trailing edge curves symmetrical)
Figure 38. Relative strength of magnetic field using two sample samarium cobalt magnets, versus
variances in air gap and flux concentrator usage (see key table)
Table 3. Key for Figure 38
Air Gap
(mm)
Transition Region Slope
(G / mm)
Concentrator* Usage
1
2.5
551
Yes
2
2.5
388
No
3
2.5
354
Yes
4
3.0
343
Yes
5
2.5
307
No
6
3.0
248
No
7
3.0
220
Yes
8
3.0
177
No
Chart Symbol
Note: Samples using two samarium cobalt cubic magnets, Allegro U package
*Concentrator cylindrical, composed of mild steel, Ø3.2 mm, length 6.4 mm, attached to non-branded
face of the Allegro U package case
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
21
Flux Concentrators Pay Dividends
Temperature Coefficients:
What if economic or size considerations dictated use of the
smaller magnet sampled for figure 38, and mechanical considerations dictated the larger (3.0 mm) air gap, but the resulting
flux density and slope (curve 8) were not good enough? Curve 7
in figure 38 shows the very substantial improvement that can be
achieved by adding simple flux concentrators. Those used in the
example were 3.2 mm in diameter by 6.4 mm long, and were
fastened behind the Hall switch.
• ΔBOP /Δ T, maximum = 0.7 G/°C
Flux Concentrator Design Example
The magnet/concentrator configuration we just considered
(curve 7, figure 38) seems to offer a high performance/cost ratio.
Following is an evaluation of its use in an automotive ignition
system using a 63.5 mm diameter cup rotor.
The initial timing and wide operating temperature range requirements for this application have generally led designers to specify
custom Hall switches in terms of the minimum and maximum
operate or release point at +25°C, plus a maximum temperature
coefficient on these parameters over the operating temperature
range.
Representative specifications might be:
• 25°C operate point, minimum, BOP(min) = 300 G
• 25°C operate point, maximum, BOP(max) = 450 G
• ΔBRP /Δ T, maximum = 1.0 G/°C
Solid-state Hall-effect ignition systems can be designed to fire
either on the operate or release switchpoints of the Hall switch.
We have arbitrarily chosen to have the system in this example fire
at the operate switchpoints and, thus, the operate point specifications of the Hall switch (between 300 and 450 G at 125°C) will
determine the amount of uncertainty in the initial timing of the
spark. It is possible that the mechanical system would also make
a contribution, but that is not considered here.
Figure 39 shows the measured flux density at the position of the
sensor IC as a function of the vane travel. The shape of the curve
(which shows only the transition regions) requires explanation.
Because the regions of flat minimum and maximum flux are
irrelevant, it is convenient to measure from the vane leading edge
to the magnet centerline while plotting data for the falling transition, and from the vane trailing edge to the magnet centerline
while plotting data for the rising transition. This results in a curve
that has the same appearance as if all data taken while a vane
passed the magnet centerline were plotted, and then the low flux
areas were deleted, and the sections containing the linear transition regions were joined together. (The flat high flux regions are
simply omitted.)
From this graph, we can identify the magnetic slope of the
transition regions for our system as being approximately 223 G
• 25°C release point, minimum, BRP(min) = 200 G
25°C Initial timing uncertainty
(1.2 distributor degrees)
700
Magnetic Flux Density, B (G)
600
500
25°C maximum
Operate Point
Magnetic slope =
223 G/mm
400 125 G/distributor degree
25°C minimum
Operate Point
300
200
25°C minimum
Release Point
100
0
–5.1
–3.8
–2.5
–1.3
0
1.3
2.5
3.8
5.1
Distance Between Vane Leading (–) or Trailing (+) Edge
and Centerline of Magnet / Hall Element (mm)
Figure 39. Design example of magnetic characteristic of a single-vane cup target (showing only magnetic flux transition regions)
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
22
per mm of vane travel. Calculations based on the rotor diameter
(63.5 mm) show we have 0.55 mm of vane travel per distributor
degree. The 223 G/mmm slope obtained from figure 39 is equivalent to 125 G per distributor degree. From the specifications, it
is known that the Hall switch will operate when flux is between
300 G and 450 G, leaving a 150 G window of uncertainty. At
25°C, this uncertainty will be:
150 G × (Distributor Degree / 125 G) =
1.2 Distributor Degrees
A typical samarium cobalt magnet temperature coefficient is
–0.04% per °C. At that rate, a magnetic field of 375 G at 25°C
would decrease to 360 G at 125°C. Applying that rate to the data
from figure 39 (with a magnetic slope of 223 G/mm), in figure 40
we can see our system having an additional vane travel requirement at 125°C. This can be calculated as:
(375 G - 360 G) × (1 mm / 223 G) = 0.1 mm
This translates to timing change of:
Additional contributions to the initial timing uncertainty will
result if the total effective air gap is changed, because that would
affect the shape or slopes of the magnetic flux density/vane travel
curve of figure 39. Factors to be considered are the magnet peak
energy product tolerances, as well as manufacturing tolerances in
the final Hall switch/ magnet assembly.
Temperature Stability of Operate Points
An early Hall switch operate-point temperature coefficient was
approximately 0.2 G/°C. To translate this into distributor degrees
per degree Celsius, we take:
(0.2 G / 1°C) × (Distributor Degree / 125 G) =
0.0016 Distributor Degrees / °C
The distributor timing would, therefore, change 0.16 degrees for
a temperature change of 100°C.
0.1 mm × (1 Distributor Degree / 0.55 mm) =
0.12 Distributor Degrees
for a temperature change of 100°C.
Calculating Dwell Angle and Duty Cycle Variations
The dwell angle in a conventional system is the quantity of
distributor degrees during which the distributor points are closed.
This corresponds to the amount of time current can flow in the
ignition coil primary winding. In our example, current flows in
the coil primary from the time of the Hall release switchpoint
until the next operate switchpoint (the effective vane width). For
nostalgic reasons, we will assume an eight-cylinder engine, which
requires a distributor rotor with eight windows and eight vanes of
equal size. Thus, a single window-vane segment occupies 45 distributor degrees and will fire one cylinder. Let us further assume
a typical Hall device operate switchpoint of 375 G at 25°C (A in
figure 40), and a 25°C release point of 260 G (B in figure 40).
700
Magnetic Flux Density, B (G)
600
1.9 mm
500
Magnetic slope =
223 G/mm
400 125 G/distributor degree
300
200
(D)125°C Release
Point (360 G)
1.5 mm 1.5 mm
1 mm
(C) 125°C Operate
Point (445 G)
(A) 25°C Operate
Point (375 G)
(B) 25°C Release
Point (260 G)
100
0
–5.1
–3.8
–2.5
–1.3
0
1.3
2.5
3.8
5.1
Distance Between Vane Leading (–) or Trailing (+) Edge
and Centerline of Magnet / Hall Element (mm)
Figure 40. Design example of magnetic characteristic of a single-vane cup target (showing only magnetic flux transition regions), showing effects of
temperature change on switchpoints
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
23
From figure 40 we find that the ignition points will close 1 mm
before the vane leading edge passes the magnet centerline, and
they will open 1.5 mm after the vane trailing edge passes the
magnet centerline. We can calculate how much greater the effective vane width is than the mechanical vane width, as follows:
(1 mm + 1.5 mm) × (1 Distributor Degree / 0.55 mm) =
4.54 Distributor Degrees
This gives a dwell angle of (45° + 4.54°) = 49.54 Distributor
Degrees at 25°C. The duty cycle is then:
Individual Calibration Techniques
In some applications, it may be required to have the vane-Hall
device assemblies operate within a narrower range of vane edge
positions than is possible with a practical operate point specification for the Hall device, for example, if it were necessary to
reduce the initial timing window in the example of the ignition
distributor. One solution would be individual calibration. Possible
techniques include some or all of the following:
• Adjusting the air gap by changing the magnet position
• Adjusting the position of a flux concentrator on the back side of
the Hall device
(49.54° / 90°) = 55%, at 25°C
Using the specified worst-case temperature coefficients, we
calculate the new operate and release switchpoints at 125°C to
be 445 G (C in figure 40) and 360 G (D in figure 40). The dwell
angle at +125°C would then be:
45° + [(1.85 mm +1.47 mm) × (1 Distributor Degree / 0.55 mm) =
50.9 Distributor Degrees
The duty cycle is then:
51° / 90° = 57%
Effects of Bearing Wear
A ±0.3 mm radial movement of the vane, with its position
adjusted to the approximate operate point of the Hall switch, gave
a measured change of ±6 G. This translates into a change of:
6 G × (1 Distributor Degree /125 G) =
0.048 Distributor Degrees
which is equivalent to 0.097 crankshaft degrees.
Mounting Also Affects Stability
In the example above, it was assumed that the physical relationship between the Hall switch and the magnet was absolutely
stable. In practice, it is necessary to design the mountings with
some care if this is to be true. It has been found that supporting
the magnet or Hall switch with formed brackets of aluminum or
brass will often contribute a significant temperature-related error
to the system. Use of molded plastic housings has proven to be
one of the better mounting techniques.
27701-AN, Rev. 2
Enhancement Considerations
• Adjusting the position of a small bias magnet mounted on the
back side of the Hall device
• Demagnetizing the magnet in small increments that would
decrease the magnetic slope and, thus, increase the temperature
effects
• Adjusting the position of the Hall device-magnet assembly relative to the rotor in a manner similar to rotating an automotive
distributor to change the timing
Operating Modes: Head-On and Slide-By
The most common operating modes are head-on (see figure 12B)
and slide-by (see figure 13). The head-on mode is simple and
relatively insensitive to lateral motion, but cannot be used
where overextension of the mechanism might damage the Hall
device. The flux-density plot for a typical head-on operation
(see figure 41) shows that the magnetic slope is quite shallow
for low values of flux density, a disadvantage that generally
requires extreme mechanism travel and extreme sensitivity to
flux changes in the operate and release switchpoints of the Hall
device. This problem can be overcome by selecting Hall devices
with higher operate and release properties.
The slide-by mode is also simple, can have reasonably steep
slopes (to about 394 G/mm), and has no problem with mechanism over-travel. It is, however, very sensitive to lateral play, as
the flux density varies dramatically with changes in the air gap.
This can be seen clearly in the curves of figure 42, in which the
flux density curves are plotted for actual slide-by operation with
various air gaps. It is apparent that the operating mechanism can
have little side play if precise switching is required.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
24
AAD and Package Contribution
0
0
2.5
5.1
7.6
10.2
Relative Output Voltage
Relative Magnetic Flux Density, B
VCC
+
TEAG
AAD
N
S
VOQ
12.7
Total Effective Air Gap, TEAG (mm)
VCC
+
TEAG
5.3 mm
TEAG = 1.3 mm
Relative Output Voltage
Relative Magnetic Flux Density, B
Figure 41. Example of the magnetic flux characteristic in head-on configuration
TEAG = 1.9 mm
TEAG = 2.4 mm
0
0
1.3
2.5
3.8
5.1
N
S
D
VOQ
6.4
Distance Between Centerlines of Magnet
and Hall Element, D (mm)
Figure 42. Example of effect of lateral displacement on the magnetic flux characteristic in slide-by configuration
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
25
Operating Mode Enhancements: Compound Magnets
Push-Pull
Because the active area of a Hall switch is close to the branded
face of the package, it is usually operated by approaching this
face with a magnetic south pole. It is also possible to operate a
Hall switch by applying a magnetic north pole to the back side of
Mo
the package. While a north pole alone is seldom used, the pushpull configuration (simultaneous application of a south pole to
the branded side and a north pole to the back side) can give much
greater field strengths than are possible with any single magnet
(see figure 43). Perhaps more important, push-pull arrangements
are quite insensitive to lateral motion and are worth considering if
a loosely fitting mechanism is involved.
n
tio
Mo
tio
n
Figure 43. Examples of compound magnet configurations (either the Hall device or the magnet assembly can be stationary), with a south pole toward the
branded face and a north pole toward the back side: (left) push-pull head-on and (right) push-pull slide-by
Magnetic Flux Density, B (G)
2000
3.6 mm
1600
1200
NS
Magnetic Slope =
–315 G / mm
800
NS
D
400
Back face
0
0
1.3
2.5
3.8
5.1
6.4
Branded face
Distance Between Centerlines of Magnet
and Hall Element, D (mm)
Figure 44. Example of magnetic flux characteristic in push-pull slide-by magnet configuration
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
26
Figure 44 shows the flux-density curve for an actual push-pull
slide-by configuration that achieves a magnetic slope of about
315 G/mm.
figuration in the head-on mode (see figure 45).
In the push-push, head-on mode configuration shown in figure
45, the magnetic fields cancel each other when the mechanism
is centered, giving zero flux density at that position. Figure 46
shows the flux-density plot of such a configuration. The curve is
linear and moderately steep at better than 315 G/mm. The mechanism is fairly insensitive to lateral motion.
Push-Push
Another possibility, a bipolar field with a fairly steep slope
(which also is linear), can be created by using a push-push con-
Mo
n
tio
Figure 45. Example of a push-push head-on compound magnet configuration (either the Hall device or the magnet assembly can be stationary), with
south poles toward both the branded face and the back side
Magnetic Flux Density, B (G)
500
Ø5.4 mm
4.8 mm
5.3 mm
4.8 mm
300
100
N
0
-100
S
S
N
Magnetic Slope =
315 G / mm
-300
Alinco 8 Magnets
-500
-1.5
-1.0
-0.5
0
0.5
1.0
1.5
Magnet Assembly Travel (mm)
Figure 46. Example of push-push head-on mode magnet configuration, in which the fields cancel in the middle of the travel range
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
27
Biased Operation
It is also possible to bias the Hall device by placing a stationary north or south pole behind it to alter the operate and release
points. For example, a north pole attached to the reverse face
would configure the device as normally turned on, until a
north pole providing a stronger field in the opposite direction
approached the opposite face (figure 47).
Figures 48-50 demonstrate additional slide-by techniques.
Compound magnets are used in push-pull slide-by configurations
to achieve a magnetic slope of 685 G/mm. Rare-earth magnets
may be used to obtain substantially steeper slopes. A flux density
curve of up to 3937 G/mm is obtainable.
Branded
face
S
N
N
Mo
S
Mo
S
n
tio
Branded
face
N
tio
n
N
Back-biasing
magnet
S
Back-biasing
magnet
Figure 47. Examples of back-biasing magnet configuration, (left) slide-by and (right) head-on
5.3 mm
VCC
+
SN
VOQ
0
Single
magnets
–
GND
+
VCC
Compound
magnets
0
–
-2.5 -2.0 -1.5 -1.0
VOQ
Relative Output Voltage
Relative Magnetic Flux Density, B
4.8 mm
NS
SN
N
S
S
N
NS
D
GND
0
1.0
1.5
2.0
Distance Between Centerline of Magnet
and Hall Element, D (mm)
2.5
Compound
magnets
Single
magnets
Figure 48. Examples of slide-by motion, magnets on both sides; compound and single magnets
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
28
0
4.8 mm
Relative Output Voltage
Relative Magnetic Flux Density, B
VCC
+
VOQ
–
-10.0 -7.5 -5.0 -2.5
0
2.5
5.0
S
N
D
GND
7.5 10.0
Distance Between Centerline of Magnet
and Hall Element, D (mm)
Magnetic Flux Density, B (G)
Figure 49. Example of slide-by motion, magnet on one side, single magnet
Compound Magnet
Alinco 6
1000
Ø6 mm
4.8 mm
500
0
Magnetic Slope =
–394 G / mm
S
N
N
S
S
N
D
–500
TEAG = 1 mm
–1000
-3
-2
-1
0
1
2
3
Distance Between Centerline of Magnet
and Hall Element, D (mm)
Figure 50. Example of slide-by motion, magnets on one side, compound magnets
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
29
Increasing Flux Density by Improving the Magnetic Circuit
Magnetic flux can travel through air, plastic, and most other
materials only with great difficulty. Because there is no incentive
for flux from the activating magnet to flow through the (plastic
and silicon) Hall device, only a portion of it actually does. The
balance flows around the device and back to the other pole by
whatever path offers the least resistance (figure 51).
However, magnetic flux easily flows through a ferromagnetic
material such as mild steel. The reluctance of air is greater by a
factor of several thousand than that of mild steel.
In a Hall device application, the goal is to minimize the reluctance of the flux path from the magnetic south pole, through the
Hall device, and back to the north pole. The best possible magnetic circuit for a Hall device would provide a ferrous path for the
flux, as shown in figure 52, with the only “air gap” being the Hall
device itself.
While a complete ferrous flux path is usually impractical, unnecessary, and even impossible in applications requiring an undistorted or undisturbed flux field, it is a useful concept that points
the way to a number of very practical compromises for improving
flux density.
Flux paths
Flux paths
Mild steel
NS
NS
Hall device
Magnet
Magnet
Figure 51. Typical magnetic field generated as magnetic flux passes
through free air, with only a small portion passing through the Hall device
27701-AN, Rev. 2
Hall device
Figure 52. Demonstration of use of mild steel to provide a low-reluctance
path for magnetic flux, with a preponderance passing through the Hall device
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
30
Flux Concentrators
Flux concentrators are low-carbon (cold rolled) steel magnetic
conductors. They are used to provide a low reluctance path from
a magnet south pole, through the Hall element, and back to the
north pole. Flux concentrators can take many forms and will
often allow use of smaller or less expensive magnets (or less
expensive, less sensitive Hall devices) in applications where
small size or economy are important. They are of value whenever
it is necessary or preferred to increase flux density at the Hall
device. Increases of up to 100% are possible.
An example of the effectiveness of a concentrator is illustrated in
figure 53. Both panels show the same magnet (a samarium cobalt
magnet 6.4 mm square and 3.2 mm long) and mounting (AG =
6.4 mm). In panel A, there is a flux density of 187 G at the Hall
device active area. In panel B, with a concentrator 3.2 mm in
diameter and 12.7 mm long, the flux density increases to 291 G.
Size of the Concentrator
The active area of the Hall device is typically 0.3 mm square.
Best results are obtained by tapering the end of the concentrator to approximately the same dimensions. With the Allegro
UA package, however, there is 1.1 mm from the active area to the
back face of the package. Due to this distance, a slightly larger
end to the concentrator results in higher values of flux density at
the active area. If the end is too large, the flux is insufficiently
concentrated. Figures 54A, 54B, and 54C illustrate these effects
using cylindrical flux concentrators and a 6.4 mm air gap.
Magnet
samarium cobalt
□6.4 mm
Magnet
samarium cobalt
□6.4 mm
Concentrator
Ø3.2 mm
SN
6.4 mm
SN
3.2 mm
12.7 mm
B = 187 G
6.4 mm
3.2 mm
B = 291 G
Figure 53. Effect of back-side flux concentrator on magnetic flux intensity: (A) without concentrator and (B) with concentrator
Concentrator
Ø3.2 mm
Concentrator
Ø6.4 mm
6.4 mm
3.2 mm
12.7 mm
6.4 mm
B = 261 G
(A)
SN
SN
SN
12.7 mm
Magnet
samarium cobalt
□6.4 mm
Magnet
samarium cobalt
□6.4 mm
Magnet
samarium cobalt
□6.4 mm
Concentrator
Ø0.6 mm
Ø3.2 mm
3.2 mm
12.7 mm
6.4 mm
B = 269 G
(B)
3.2 mm
B = 291 G
(C)
Figure 54. (A) Effect of back-side flux concentrator, diameter reduced too much, diminishing field strength, B; (B) Effect of back-side flux concentrator,
diameter increased too much, diminishing field strength, B; (C) Effect of back-side flux concentrator, diameter optimally matched to device
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
31
The length of the concentrator also has an effect on the flux density. This is illustrated in figure 55.
Magnet
samarium cobalt
□6.4 mm
Cylindrical concentrators were used here for convenience, but the
body of the concentrator has little effect. The important factors
are the shape, position, and surface area of the magnet end nearest the Hall element.
Concentrator
Ø3.2 mm
SN
The effectiveness of other concentrator configurations can be
measured easily by using a calibrated linear Hall device or a commercial gaussmeter.
Mounting the Magnet to a Ferrous Plate
Mounting the magnet to a ferrous plate gives an additional
increase in flux density at the Hall element. Using the same
configuration as in figure 54C, which produced 291 G, note the
available flux attained in figures 56A and 56B with the addition
of the ferrous plate.
6.4 mm
12.7 mm
Concentrator
mild steel
□12.7 mm
0.8 mm
3.2 mm
B = 357 G
Figure 56A. Effect of 12.7 mm2 additional flux concentrator, attached to
magnet
Figure 57 shows a possible concentrator for a ring-magnet
application. Using a flux concentrator that extends to both of the
adjacent north poles, flux density increases from 265 G to 400 G
(0.4 mm air gap). Note that the concentrator has a dimple, or
mesa, centered on the Hall device. In most applications, the mesa
will give a significant increase in flux density over a flat mounting surface.
Magnet
samarium cobalt
□6.4 mm
Concentrator
Ø3.2 mm
SN
Attractive Force and Distorted Flux Field
Whenever a flux concentrator is used, an attractive force exists
between magnet and concentrator. This may be detrimental to the
application.
Concentrator
mild steel
□25.4 mm
6.4 mm
12.7 mm
3.2 mm
0.8 mm
B = 389 G
Figure 56B. Effect of 25.4
magnet
additional flux concentrator, attached to
200
S
N
N
S
S
N
0
0
12.7
N
Magnetic Flux Density, B (G)
400
mm2
S
25.4
Concentrator Length (mm)
Dimple
Figure 55. Effect of back-side flux concentrator length, using a samarium
cobalt magnet of Ø3.2 mm and AG = 6.4 mm
27701-AN, Rev. 2
Figure 57. Demonstration of mesa-type bracket and flux concentrator
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
32
Feed-Throughs
An example of the use of a magnetic conductor to feed flux
through a nonferrous housing is shown in figure 58. A small electric motor has a 3.2 mm cube samarium cobalt magnet mounted
in the end of its rotor, as shown. A 3.2 mm cube ferrous conductor extends through the alloy case with a 0.8 mm air gap between
it and the magnet south pole. The Hall switch is mounted at the
other end with a flux concentrator behind it.
In general, the feed-through should be of approximately the same
cross-sectional area and shape as is the magnet pole end. This
concept can be used to feed flux through any non-ferrous material, such as a pump case, pipe, or panel.
The two curves of figure 59 illustrate the effects on flux density
of increasing the length of the feed-through, as well as the contri-
bution by the flux concentrator behind the Hall switch. Values for
curve A were obtained with the flux concentrator in place, those
for curve B without it. In both cases, the highest flux densities
were achieved with the shortest feed-through dimension L, which
was 3.2 mm. Peak flux density was 350 G with flux concentrator
in place, 240 G without it.
Magnet Selection
A magnet must operate reliably with the total effective air gap in
the working environment. It must fit the available space. It must
be mountable, affordable, and available.
Figures Of Merit
The figures of merit commonly applied to magnetic materials are:
• Residual induction (Br) in gauss (G). How strong is the magnetic field?
Feed-through
Magnet on rotor
• Coercive force (Hc) in oersteds (Oe). How well will the magnet
resist external demagnetizing forces?
• Maximum energy product (BHmax) in gauss-oersteds × 106. A
strong magnet that is also very resistant to demagnetizing forces
has a high maximum energy product. Generally, the larger the
energy product, the better, stronger, and more expensive the
magnet.
SN
Rotor
Figure 58. Typical application for feed-through of magnetic signal from
target to Hall device
• Temperature coefficient. The rate of change of the operate or
release switchpoints over the full operating temperature range,
measured in gauss per degree Celsius. How much will the
strength of the magnet change as temperature changes?
Magnet
Samarium Cobalt
□3.2 mm
Magnetic Flux Density, B (G)
400
L
300
(A) With flux
concentrator
N
200
S
0.8 mm
100
(B) Without flux
concentrator
Feed-through
0
conductor
0
3.2
6.4
9.5
12.7
15.9
Ø3.2 mm
Feed-Through Conductor Length, L (mm)
Flux
concentrator
Figure 59. Example of feed-through conductor length effect on magnetic flux, with and without a flux concentrator on the device
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
33
Magnetic Materials
energy product is approximately 1.4 × 106.
Neodymium (Ne-Fe B). The new neodymium-iron-boron alloys
fill the need for a high maximum-energy product, moderately
priced magnet material. The magnets are produced by either a
powdered-metal technique called orient-press-sinter or a new
process incorporating jet casting and conventional forming techniques. Current work is being directed toward reducing production costs, increasing operating temperature ranges, and decreasing temperature coefficients. Problems relating to oxidation of
the material can be overcome through the use of modern coatings
technology. Maximum energy products range from 7 to 15 MGOe
depending on the process used to produce the material.
Iron-chromium magnets have magnetic properties similar to
Alnico 5, but are soft enough to undergo machining operations
before the final aging treatment hardens them. Maximum energy
product is approximately 5.25 × 106.
Rare-earth cobalt is an alloy of a rare-earth metal, such as samarium, with cobalt (abbreviated as RE cobalt). These magnets are
the best in all categories, but are also the most expensive by about
the same margins. Too hard for machining, they must be ground
if shaping is necessary. Maximum energy product, perhaps the
best single measure of magnet quality, is approximately 16 × 106.
Alnico is a class of alloys containing aluminum, nickel, cobalt,
iron, and additives that can be varied to give a wide range of
properties. These magnets are strong and fairly expensive, but
less so than RE cobalt. Alnico magnets can be cast, or sintered
by pressing metal powders in a die and heating them. Sintered
Alnico is well suited to mass production of small, intricately
shaped magnets. It has more uniform flux density, and is mechanically superior. Cast Alnico magnets are generally somewhat
stronger. The non-oriented or isotropic Alnico alloys (1, 2, 3, 4)
are less expensive and magnetically weaker than the oriented
alloys (5, 6, 5-7, 8, 9). Alnico is too hard and brittle to be shaped
except by grinding. Maximum energy product ranges from
1.3 × 106 to 10 × 106.
Ceramic magnets contain barium or strontium ferrite (or another
element from that group) in a matrix of ceramic material that is
compacted and sintered. They are poor conductors of heat and
electricity, are chemically inert, and have-high values of coercive
force. As with Alnico, ceramic magnets can be fabricated with
partial or complete orientation for additional magnetic strength.
Less expensive than Alnico, they also are too hard and brittle to
shape except by grinding. Maximum-energy product ranges from
1 × 106 to 3.5 × 106.
Cunife is a ductile copper base alloy with nickel and iron. It can
be stamped, swaged, drawn, or rolled into final shape. Maximum
27701-AN, Rev. 2
Plastic and rubber magnets consist of barium or strontium ferrite in a plastic matrix material. They are very inexpensive and
can be formed in numerous ways including stamping, molding,
and machining, depending upon the particular matrix material.
Because the rubber used is synthetic, and synthetic rubber is also
plastic, the distinction between the two materials is imprecise.
In common practice, if a plastic magnet is flexible, it is called a
rubber magnet. Maximum energy product ranges from 0.2 × 106
to 1.2 × 106.
Choosing Magnet Strength
A magnet must have sufficient flux density to reach the Hall
switch maximum operate-point specification at the required air
gap. Good design practice suggests the addition of another 50 G
to 100 G for insurance and a check for sufficient flux at the
expected temperature extremes.
For example, if the Hall device datasheet specifies a 350 G
maximum operate point at 25°C, after adding a pad of 100 G, we
have 450 G at 25°C. If operation to 70°C is required, the specification should be 450 G + 45 G = 495 G. (For calculations, we
use 0.7 G/°C operate point coefficient and 1 G/°C release point
coefficient.) Because the temperature coefficient of most magnets
is negative, this factor would also require some extra flux at room
temperature to ensure high-temperature operation.
Coercive Force
Coercive force becomes important if the operating environment
will subject the magnet to a strong demagnetizing field, such as
that encountered near the rotor of an AC motor. For such applications, a permanent magnet with high coercive force (ceramic,
Alnico 8, or, best of all, RE cobalt) is clearly indicated.
Price and Peak Energy Product
The common permanent magnet materials and their magnetic
properties are summarized in table 4. The Cost column shows
the relationship between the price paid for a magnet and its peak
energy product.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
34
Table 4. Properties of Magnetic Materials
Material
Maximum
Energy Product
(G-Oe)
Residual
Induction
(G)
Coercive Force
(Oe)
RE cobalt
16×106
8.1×103
7.9×103
–0.05
Highest
Strongest,
smallest, resists
demagnetizing
best
Alnico 1, 2, 3, 4
1.3 to 1.7×106
5.5 to 7.5×103
0.42 to 0.72×103
–0.02 to –0.03
Medium
Nonoriented
Alnico 5, 6, 5-7
4.0 to 7.5×106
0.64 to
0.78×103
–0.02 to –0.03
Medium to high
Oriented
Alnico 8
5.0 to 6.0×106
1.5 to
1.9×103
–0.01 to 0.01
Medium to high
Oriented, high
coercive force,
best temperature
coefficient
Alnico 9
10×106
10.5×103
1.6×103
–0.02
High
Oriented, highest
energy product
Ceramic 1
1.0×106
2.2×103
1.8×103
–0.02
Low
Nonoriented,
high coercive
force, hard, brittle,
nonconductor
Ceramic 2, 3, 4, 6
1.8 to 2.6×106
Low-medium
Partially oriented,
very high coercive
force, hard, brittle,
nonconductor
Ceramic 5, 7, 8
2.8 to 3.5×106
–0.02
Medium
Fully oriented,
very high coercive
force, hard, brittle,
nonconductor
Cunife
1.4×106
5.5×103
0.53×103
–
Medium
Ductile, can cold
form and machine
Fe-Cr
5.25×106
13.5×103
0.60×103
–
Medium
Can machine
prior to final aging
treatment
Plastic
0.2 to 1.2×103
1.4 to 3×103
0.45 to 1.4×103
–0.02
Lowest
Can be molded,
stamped,
machined
Rubber
0.35 to 1.1×106
1.3 to 2.3×103
1 to 1.8×103
–0.02
Lowest
Flexible
Neodymium
7 to 15×106
–0.157 to –0.192
Medium-high
27701-AN, Rev. 2
10.5 to
7 to
13.5×103
9.2×103
2.9 to
3.3×103
3.5 to
3.8×103
6.4 to
11.75×103
2.3 to
2.8×103
2.5 to
3.3×103
5.3 to
6.5×103
Temperature
Coefficient
(%/°C)
–0.02
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Cost
Comments
Nonoriented
35
Advanced Applications
r
Current Limiting and Measuring Current Sensor ICs
Hall-effect devices are excellent current-limiting or measuring
devices. Their response ranges from DC to the kHz region. The
conductor need not be interrupted in high-current applications. For
a current list of Allegro current sensor ICs visit http://www.allegromicro.com/en/Products/Categories/Sensors/currentsensor.asp.
The magnetic field about a conductor is normally not intense
enough to operate a Hall effect device (see figure 60). The radius
(r) is measured from the center of the conductor to the active area
of the Hall device. With a radius of 12.7 mm and a current of
1000 A, there would be a magnetic flux density of 159 G at the
Hall device.
For low current applications, consider the use of a toroid, as
illustrated in figures 61A and 61B, to increase the flux density as
it passes through the Hall element. With a 1.5 mm air gap in the
toroid, for the Allegro UA package there will be a magnetic gain
of 6 G/A for just the circuit illustrated in figure 61B. To increase
the sensitivity of the circuit, consider winding multiple turns of
the conductor around the toroid, as shown in figure 61A. The
example in figure 61A has 14 turns, and would therefore have a
magnetic gain of 84 G/A.
B (G) ≈
I (A)
0.16
r (mm)
Figure 60. The magnetic flux density decreases with distance from a
conductor
Figure 61A. Demonstration of use of coil and toroid for low-current sensing
The core material can be of either ferrite or mild steel (C-1010)
for low-frequency applications, and ferrite for high-frequency
measurements.
The main concerns are:
• The core should retain minimal field when the current is reduced to zero
• The flux density in the air gap should be a linear function of the
current
• The air gap should be stable over the operating temperature
range
The cross-sectional dimensions of the core are at least twice the
air gap dimension to ensure a reasonably homogeneous field in
the gap. For example, a toroid with a 1.5 mm gap should have at
least a 3 mm × 3 mm cross-section.
Another simple and inexpensive application is illustrated in figure 62. A toroid of the appropriate diameter is formed from mildsteel stock, 1.6 mm thick and 4.8 mm wide. The ends are formed
to fit on each side of the central portion of the Hall device. One
advantage of this technique is that the toroid can be placed
around a conductor without disconnecting the conductor.
Multi-Turn Applications
There are several considerations in selecting the number of turns
for a toroid such as the one in figure 61A.
27701-AN, Rev. 2
Figure 61B. Demonstration of use of toroid for current sensing for
moderate current (I >25 A)
Toroid
4.8 mm
Conductor
1.6 mm
Figure 62. Demonstration of Hall current sensing application that allows
mounting without disconnecting the conductor
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
36
Hall Switches
Keep the flux density in the 100 to 200 G range for a trip point.
Devices can be supplied with a narrow distribution of magnetic
parameters within this range. If, for example, you want the Hall
switch to turn on at 10 A:
N = 200 G / (6 G/A × 0.01 A) = 3333 turns
N = 300 G / (6 G/A × 10 A) = 5 turns
Hall Linears
It is preferrable to have flux density above 100 G to maximize the
output signal/quiescent output drift ratio. The quiescent output
drift for ratiometric sensor ICs is typically 0.2 mV/°C, while the
sensitivity temperature coefficient is typically 0.02%/°C. Some
Allegro devices allow the sensitivity and/or quiescent output drift
to be customized for a specific application. For a current list of
Allegro linear ICs visit http://www.allegromicro.com/en/Products/Categories/Sensors/linear.asp.
For low-current applications in which many turns are required,
wind a bobbin, slip it over a core, and complete the magnetic
circuit through the Hall device with a bracket-shaped pole piece,
as shown in figure 63.
Other Applications For Linear Sensor ICs
Hall-effect linear sensor ICs are used primarily to sense relatively
small changes in magnetic field, changes too small to operate a
Hall-effect switching device. They are customarily capacitively
coupled to an amplifier, which boosts the output to a higher level.
As motion detectors, gear tooth sensor ICs, and proximity detectors (figure 64), they are magnetically driven mirrors of mechanical events. As sensitive monitors of electromagnets, they can
effectively measure system performance with negligible system
loading while providing isolation from contaminated and electrically noisy environments.
The output null (quiescent) voltage is nominally one-half the
supply voltage. A south magnetic pole presented to the branded
face of the Hall-effect sensor IC will drive the output higher than
the null voltage level. A north magnetic pole will drive the output
below the null level.
Coil
Core
Figure 63. Demonstration of Hall current sensing application using a coil
for low-amperage circuits
Branded face
It would be practical to tweak the air gap for final, more precise
calibration. In all cases, be careful not to stress the package.
Each Hall-effect integrated circuit includes a Hall element, linear
amplifier, and emitter-follower output stage. Problems associated
with handling tiny analog signals are minimized by having the
Hall element and amplifier on a single chip.
Hall device
Pole piece
(concentrator)
With this bobbin-bracket configuration, it is possible to measure
currents in the low milliampere range or to replace a relay using
a Hall switch. To activate a Hall switch at 10 mA (±20%), using
a device with a 200 G (±40 G) operate point, bobbin windings
require:
In operation, instantaneous and proportional output-voltage levels
are dependent on magnetic-flux density at the most sensitive area
of the device. Greatest sensitivity is obtained with the highest
Branded face
Figure 64. Examples of application of Hall devices for monitoring mechanical events: (left) north pole adjacent to sense the absence of ferrous material,
(right) south pole adjacent to sense the presence of ferrous material
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
37
supply voltage allowed, but at the cost of increased supply current and a slight loss of output symmetry. The sensor IC output is
usually capacitively coupled to an amplifier that boosts the output
above the millivolt level.
In the two applications shown in figures 65 and 66, permanent
bias magnets are attached with epoxy glue to the back of the
epoxy packages. The presence of ferrous material at the face of
the package then acts as a flux concentrator.
The south pole of a magnet is attached to the back face of the
package if the Hall-effect IC is to sense the presence of ferrous
material. The north pole of a magnet is attached to the back face
if the integrated circuit is to sense the absence of ferrous material.
Calibrated linear Hall devices, which can be used to determine
the actual flux density presented to the sensor IC in a particular
application, are available.
S
+5 V
Frequency response characteristics of this circuit are easily controlled by changing the value of the input decoupling capacitor
for the low-frequency break-point. If high-frequency attenuation
is required, a capacitor can be used to shunt the feedback resistor.
Metal Sensor IC The north pole of the magnet is affixed to the
back side of a linear sensor IC . The device is in contact with the
bottom of a 2.4 mm epoxy board. An output change (decrease) is
produced as a 25 mm steel ball rolls over the device. This signal
is amplified and inverted by the operational amplifier and drives
the NPN transistor on.
Notch Sensor IC The south pole of the magnet is fixed to the
backside of a linear sensor IC . The sensor IC is 0.8 mm from
the edge of a steel rotor. A 1.6 mm wide by 3.2 mm deep slot
in the rotor edge passing the sensor IC causes an output change
(decrease). This signal is amplified and inverted by the operational amplifier and drives the NPN transistor on.
Note that, in both examples, the branded side of the sensor IC
faces the material (or lack of material) to be sensed. In both
cases, the presence (or absence) of the ferrous metal changes
the flux density at the Hall-effect sensor IC so as to produce a
negative-going output pulse. The pulse is inverted by the amplifier to drive the transistor on.
27701-AN, Rev. 2
1 μF
Output
Ground
470 kΩ
Load
1 kΩ
470 Ω
10 kΩ
Figure 65. Typical external back-biasing application circuit to detect
presence of target
+V
S
N
+5 V
22 μF 2.2 kΩ
Output
Ground
Ferrous Metal Detectors
Two similar detector designs are illustrated in figures 67 and 68.
The first senses the presence of a ferrous metal; the other senses
an absence of the metal. The two sensing modes are accomplished simply by reversing the magnet poles relative to the sensor IC . The pole of the magnet is affixed to the unbranded side of
the package in both cases.
+V
N
470 kΩ
Load
470 Ω
10 kΩ
Figure 66. Typical external back-biasing application circuit to detect
absence of target
+V
N
S
+5 V
22 μF
Output
Ground
470 kΩ
Load
2.2 kΩ
470 Ω
10 kΩ
Figure 67. Typical external back-biasing application circuit to detect the
presence of a ferromagnetic target
+V
S
N
+5 V
Ground
1 μF
Output
470 kΩ
Load
1 kΩ
470 Ω
10 kΩ
Figure 68. Typical external back-biasing application circuit to detect the
absence of a ferromagnetic target
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
38
Sensitivity is so great in this configuration that the output signal
baseline quite closely tracks eccentricities in the drum. This
affects lobe resolution, but lobe position can still be measured.
Printer Application
The assembly in figure 69 senses lobes on a character drum.
Lobes are spaced 4.8 mm apart around the circumference of the
drum, they are 6.4 mm wide, and have a depth of 0.3 to 0.4 mm
relative to the surface of the drum.
Using Calibrated Devices
The calibrated linear sensor IC is an accurate, easy-to-use tool for
measuring magnetic flux densities. Each device is individually
calibrated and furnished with a calibration curve and sensitivity coefficient. Although calibration is performed in a north and
south 800 G field, the sensor IC is useful for measuring fields in
both polarities.
In this application, a Hall-effect linear sensor IC is back biased
with a magnet. The north pole is affixed to the back side of the
package. A flux concentrator is affixed to the branded face.
Although it does not provide a flux return path, the concentrator
will focus the magnetic field through the switch.
The concentrator, shown in figure 70, is aligned with the drum
lobe at an air gap distance of 0.254 mm. The output change is
amplified to develop a 3 V output from the operational amplifier,
driving the transistor on, as illustrated in figure 71.
A closely regulated (±10 mV) power supply is necessary to
preserve accuracy in calibrated flux measurements. An ambient
temperature range of 21°C to 25°C must also be maintained.
Connect the VCC pin to voltage VCC, GND pin to ground, and
the VOUT pin to a high-impedance voltmeter. Before use, the
0.381 mm MAX
0.254 mm
Concentrator
Magnet
S
N
Branded face
Figure 69. Demonstration of printer drum monitoring application
+15 V
S
Ø0.8 mm
1 MΩ
N
+5 V
VCC
3.2 mm
Ø1.6 mm
Ground
Figure 70. Printer drum sensing application flux concentrator
27701-AN, Rev. 2
3.3 kΩ
270 Ω
1 kΩ
Output
10 kΩ
Figure 71. Printer drum typical application circuit
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
39
device should be powered-up and allowed to stabilize for one
minute.
The sensitivity coefficient can be used to calculate flux densities
precisely. First, determine the null output voltage of the device
under 0 G or null (quiescent) field condition. Then, read the output of the device under an applied field condition by subjecting it
to the flux in question. Magnetic flux density at the device can be
calculated by:
B = ( VOUT(B) – VOUT(Q) ) × 1000 / S
where:
VOUT(B) is the output voltage under the applied magnetic field,
in V,
VOUT(Q) is the quiescent field output, in V,
S is the sensitivity coefficient, in mV/G, and
B is the magnetic flux density at the device, in G.
Glossary
active area: the site of the Hall element on the encapsulated IC
chip.
air gap: the distance from the face of the magnetic pole or target to
the face of the package.
ampere-turn (NI): the mks unit of magnetomotive force.
ampere-turns/meter (NI/m): the mks unit of magnetizing force. One
ampere-turn per meter equals 79.6 oersteds.
bipolar: a method of operating a Hall sensor IC using both north
and south magnetic poles.
coercive force (Hc): the demagnetizing force that must be applied
to reduce the magnetic flux density in a magnetic material to
zero; measured in oersteds.
concentrator: any ferrous metal used to attract magnetic lines of
force.
gauss (G): the CGS unit of magnetic flux density. Equivalent to
one maxwell per square centimeter (Mx/cm2). One gauss equals
10–4 tesla.
gilbert: the CGS unit of magnetomotive force.
head-on: a method by which the Hall sensor IC is actuated. The
magnetic field is increased and decreased by moving the magnetic
pole toward and away from the package face.
maximum energy product (BHmax): the highest product of B and H
from the demagnetization curve of a magnetic material. Given
in gauss-oersteds × 106 (MGOe).
maxwell (Mx): the CGS unit of total magnetic flux. One maxwell
equals 10–8 webers.
oersteds (Oe): the CGS unit of magnetizing force. Equivalent to
gilberts per centimeter (gilberts/cm). One oersted equals 125.7
ampere-turns per meter.
remnant induction (Bd): the magnetic induction that remains in a
magnetic circuit after removal of an applied magnetomotive force.
When there is no air gap in the magnetic circuit, remnant and
residual induction are equal. With an air gap, remnant induction
will be less than residual induction. Measured in gauss.
residual induction (Br): the flux density remaining in a closed magnetic circuit of magnetic material when the magnetizing force
adequate to saturate the material is reduced to zero. Measured
in gauss.
slide-by: a method by which a Hall sensor IC is actuated. The magnetic field is increased and decreased as a permanent magnet is
moved laterally past the package face.
tesla (T): the mks unit of magnetic flux density. Equivalent to one
weber per square meter (Wb/m2). One tesla equals 104 gauss.
toroid: a doughnut-shaped ring often composed of iron, steel, or
ferrite.
total effective air gap (TEAG): the distance from the face of a magnetic
pole or target to the active area of a Hall-effect sensor IC.
unipolar: a method of operating a Hall sensor IC using a single
magnetic pole, usually the south pole.
vane: any ferrous metal used to shunt a magnetic field away from
the Hall sensor IC (at least 1.5 times the width of an associated
magnet).
window: an opening in a vane at least 1.5 times the width of an
associated magnet.
Copyright ©1987-2013, Allegro MicroSystems, LLC
The information contained in this document does not constitute any representation, warranty, assurance, guaranty, or inducement by Allegro to the
customer with respect to the subject matter of this document. The information being provided does not guarantee that a process based on this information will be reliable, or that Allegro has explored all of the possible failure modes. It is the customer’s responsibility to do sufficient qualification
testing of the final product to insure that it is reliable and meets all design requirements.
For the latest version of this document, visit our website:
www.allegromicro.com
27701-AN, Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
40