* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download R24V-5M-D5-CW Manual
Power inverter wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Electrical substation wikipedia , lookup
Electric power system wikipedia , lookup
Three-phase electric power wikipedia , lookup
Pulse-width modulation wikipedia , lookup
Audio power wikipedia , lookup
Power MOSFET wikipedia , lookup
Amtrak's 25 Hz traction power system wikipedia , lookup
Stray voltage wikipedia , lookup
Electrification wikipedia , lookup
History of electric power transmission wikipedia , lookup
Distribution management system wikipedia , lookup
Power electronics wikipedia , lookup
Power engineering wikipedia , lookup
Buck converter wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Alternating current wikipedia , lookup
Voltage optimisation wikipedia , lookup
Switched-mode power supply wikipedia , lookup
READ ALL INSTRUCTIONS PRIOR TO INSTALLATION LED RIBBON Lights WARNING!! DO NOT CONNECT RIBBON LIGHT DIRECTLY TO 120V AC POWER!GENERAL INSTALLATION TIPS, SAFETY AND WARNINGS • • • • • DONOTCONNECTTHISRIBBONLIGHTDIRECTLYTO120VACPOWER. Please utilize the wiring diagrams in this installation guide. For larger and more complex configurations, please visit our website. Before installation, always build a pre-installation assembly and confirm that all lighting is properly connected and functional. RIBBONlightisratedonlyforusewithavoltagespecificDCClass2constantvoltagepowersource. Powersuppliesareratedformaximumpoweroutputatoptimumthermalandvoltageconditions.Foroptimumperformance,donotloadthe power supply more than 80% of its labeled rating. Please refer to the RIBBON light specifications for the wattage/amperage specs. Overloadinga DCpowersourcecanpotentiallyoverheatanddamgeyourpowersupply. • Always consult a qualified licensed electrician before beginning any electrical work. • Install in accordance with all national and local electrical codes. DCPlugandSpliceLeads: Every16.4footspool*ofRIBBONlightcomeswithboththeseconnectionoptions,butarenotnecessaryforuse.Afterconfirmingcorrectlighting con-figuration,youmaycutoffexcesswiringleads.Alwaysdeactivatethecircuitandnevercutthewiringonalivecircuit. *100 foot spools do not have DC plugs. Only leads are available for this length. STANDARD WIRING LAYOUT • The power supply, or driver, must always be installed between the RIBBON light and the 120V AC Line voltage. (See next page for more wiringdiagramlayouts). • Each16.4foot12VRIBBONlightsectionmustbeindividuallywired to your 12V DC power supply. Each 20 foot 24V Ultra Blaze RIBBON light section must be individually wired to your 24V DC powersupply. 120V AC Power ➟ N N L L AC INPUT (High Voltage) DC OUTPUT (Low Voltage) V+ (Low Voltage Driver Required) V- V+ ➟ V- TRIMMING RIBBON TO SIZE ➟ RIBBON LIGHT CONNECTORS ➟ 1. Carefullyopenlatchandnote+/-polaritymarkers. 2. FirmlyinsertRIBBONintoconnectortray.Besurethecontactpointsof the RIBBON are directly underneath the placement tabs of the ➟ (trim excess RIBBON close to contact points if lights do connector notlightuponcepowered). 3. Closethelatchtoensureconnection. ➟ ➟ ➟ – + – + – + ➟ ➟ SOLDERING – + – + ➟ (+) ➟ (–) ✂➟ • Take note of polarity markings before soldering. • Soldering should be performed by a qualified, licensed electrician. • 18-20 gauge wire. • Lead-free solder is recommended. • Solder connections can be made at any of the exposedpadslocatedatcutpointsalongtheRIBBON. ✂➟ ➟ light is operated by a DC (Direct Current) constant voltage Note:LEDRIBBON power source and is reversing the +/- ➟ ✂ ➟ WET LOCATION RIBBON LIGHT CONNECTIONS •WetLocationPrecautions:PackaginglabelwillindicateifyourRIBBONis (+) approvedfor wetlocations. •WetlocationRIBBONlightissuitableforareasexposedtomoisturelikeoutdoor patios orbathrooms. •Only the wet location RIBBON light is protected against water. Power supplies (–) and connectorsarenotwaterresistantunlessstatedotherwise. •Excessiveorexaggeratedbendingandtwistingshouldbeavoided.Thisstresscan Wet Location Connections: splitthesiliconeshellordamagetheRIBBONcircuitry. WetlocationRIBBONissurroundedbysilicone,which •Silicone adhesive must be applied to secure the water resistant connection. mustberemovedatthesolderconnections.For •WetlocationRIBBONlightshouldnotbeusedinoraroundchlorinatedpoolsorsaltwater. soldering,followtheinstructionsintheSOLDERING section. ➟ WARNING!! DO NOT CONNECT RIBBON LIGHT DIRECTLY TO 120V AC POWER! DIMMABLE APPLICATION WIRING DIAGRAMS Magnetic Dimmable Driver OurMagneticDimmableDriversareonlycompatiblewithLutron CL Series magneticlowvoltagedimmers.Refertothedimmermanufacturer’sinstallation guideforup-to-datewiringinstructions. DimmerSwitch 120VAC Power N L N H H V+ (Red) N Ground DimmableLEDFixture V– (Blue) N= Neutral / L= Line / H=Hot • • • RGB RIBBON LIGHT WIRING DIAGRAMS AllColor-ChangingRIBBONlightcomespre-solderedwithfour6inch22/4AWGleadwires. Color-ChangingRIBBONrequiresacolorcontrollerforproperuse. An RGB Signal Amplifier is required for linear runs longer than 16.4 feet. Install the amplifier between each additional spool and power the amplifier with a 12V DC power supply. PLUG-IN COLOR-CHANGING RIBBON LIGHT DIAGRAM HARD-WIRE COLOR-CHANGING RIBBON LIGHT DIAGRAM Driver 12V DC Plug-in Driver 120V AC Power Female Adapter Splice Cable 120V AC Outlet N H L N= Neutral L= Line AC INPUT (High Voltage) DC OUTPUT (Low Voltage) V+ VV+ (Low Voltage Driver Required) V- V+ Green RED Blue V- V+ Green RED Blue N V+ RGB Color Controller RGB Color Controller RGBColorChangingRIBBON RGBColorChangingRIBBON *Adapter wattage size is dependant on the load of LED lighting. Please consult the website for information on additional models and accessories. . TROUBLESHOOTING RIBBON light does not light up or is lickering: • Check and secure all connections. • Confirm polarity of wiring. (+) is connected to (+) and (-) to (-).