* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download How to Power StudioHub+ 9-6
Pulse-width modulation wikipedia , lookup
Power factor wikipedia , lookup
Voltage optimisation wikipedia , lookup
Alternating current wikipedia , lookup
Wireless power transfer wikipedia , lookup
Standby power wikipedia , lookup
Solar micro-inverter wikipedia , lookup
Power electronics wikipedia , lookup
Rectiverter wikipedia , lookup
History of electric power transmission wikipedia , lookup
Amtrak's 25 Hz traction power system wikipedia , lookup
Electrification wikipedia , lookup
Electric power system wikipedia , lookup
Audio power wikipedia , lookup
Mains electricity wikipedia , lookup
Power engineering wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Power supply wikipedia , lookup
How to Power StudioHub+ Many StudioHub+ devices are active and are powered by +/- 15vDC. Power can be supplied via the StudioHub+ “DC-Link” system that uses CAT-5 pair #4 (White/Brown) for power, or power can be supplied via a separate “wall-wart” or desk-top power supply. SeeCurrentConsumption chart to determine how many devices can be powered with different systems. NOTE – As of September, 2010 - all power supplies shown are Universal Voltage Switching Supplies and accept from 90 to 250VAC input. I- Powering via Hub ( for up to 16 devices) SH-HPB SH-HPB Headphone amps link together for audio & DC SH-MIC MatchJack PS-EXTU 3 amp +/-15VDC power supply PS-EXTU Power Supply D to A Converter Use any Hub in which the model number ends in “DC” (HUB18-DC or HUB36-DC or HUB8-DC or HUB16-DC) SH-HPB SH-HPB II - Powering via PS-Cube ( for up to 4 devices) Headphone amps link together for audio & DC SH-MIC PS-Cube MatchJack From 4 separate audio sends or feeds 5-pin MTA & 3-pin MTE power connectors (in parallel) D to A Converter 3 Amps 1 Amp Power a PS-CUBE from a Radio Systems Console Use cable part # 16998(6’) / 15884(1’) (3-pin MTA to 3-pin MTE) 1 Amp Power a PS-CUBE from a RS Console Power Supply Use cable part # 16600 (16-pin MR to 5-pin MTA) Power a PS-CUBE from a PS-EXTU Power Supply (the cable is included) (4-pin MR-4 to 5-pin MTA) Power a PS-CUBE from a PS-WWBLACK Power Supply (the captive cable is included) (captive to 3-pin MTE) MatchJack SH-HP Power a PS-CUBE from a PS-WWBLACK Power Supply (the captive cable is included) (captive to 3-pin MTE) NOTE- all power supplies shown are Universal Voltage switching supplies and accept from 100 to 240VAC input power. III- Powering via “Wall Wart” or Desk-Top Power Supply Power an individual or multiple MatchJack or Panel from a PS-WWBLACK Power Supply (the captive 3-pin to MTA cableis included) 400 mA 400 mA SH-HP NOTE- If removeable IEC power cord is required, order Part # PS-WWEXPORT Headphone amps link together for audio & DC. Power up to 5 headphone amps from one PS-WWBLACK. Current consumption for each StudioHub+ active device is charted below. Refer to this list when calculating the total number of devices that can be run on any individual power supply Part # MJ-OUT MJ-IN MJ-SPDIF MJ-AD MJ-DA MJ-DDA SH-DUALMATCH SH-HPB SH-HPDUAL SH-MATCHPANEL SH-MIC SH-MIXER SH-AMPSPKR SH-LEVEL SH-VUV SH-LCDV DA6-DC SUM4-DC Description Analog MatchJack Out (IHF to Pro) Analog MatchJack In (Pro to IHF) MatchJack In (S/PDIF and Optical to AES) Digital MatchJack A to D Digital MatchJack D to A Digital MatchJack Distribution Amplifier Dual Match Panel Headphone Panel Dual Headphone Panel Dual MatchJack IN/OUT Panel Mic Pre-Amp Panel 3 Input Stereo Mixer with mix-minus Monitor Amp Panel (w/ Speaker) Monitor Panel Dual VU Meter Panel LCD Display Panel DA Hub (Single) Combiner Hub (Single) Current 75ma 35ma 100ma 150ma 150ma 165ma* 100ma 50ma 100ma 100ma 55ma 125ma 140ma 145ma 150ma 75ma 575ma 175ma * Powered via 9v DC (single ended) wall wart or +15VDC StudioHub+ “DC-Link” power StudioHub+ Pinout Chart Channel L+ / AES + L- / AES R+ Rnc GND 15V15V+ Shield Shield Color Pair Wht/Org Org/Wht Wht/Grn Grn/Wht Wht/Blu Blu/Wht Wht/Brn Brn/Wht Wht/Slt Slt/Wht RJ-45 Pin 1 2 3 6 5 4 7 8 Shield Shield 110 Pin 3 4 5 6 1 2 7 8 9 10 StudioHub+ - Technical Bulletin Issues with connecting Powered StudioHub+ products to Axia “PowerStation” Audio Engines Note that the inputs and outputs circled in red tie RJ-45 pins 7&8 together and may not be connected directly to a powered StudioHub+ device. Issue; Some Axia PowerStation RJ-45 ANALOG and DIGITAL Input and Output ports (indicated with a “+” sign by the connector) are not compatible with StudioHub+ active (powered) components because pins 7&8 are tied together in preparation of a future powering system. Plugging a powered StudioHub+ device into one of these ports will cause the supply to shut down and potentially damage the supply and/or device. I – Solution #1 Connect the active StudioHub+ device only to non “+” ports on the Axia PowerStation engine (ANALOG Inputs and Outputs 1 or 2 / DIGITAL Inputs and Outputs 1) II – Solution #2 Prepare and utilize a special CAT-5 cable with no connection made between pins 7&8 (the brown/white pair) and plug this cable between the PowerStation engine and the active StudioHub+ device. III – Solution #3 Insert a StudioHub+ “Power-Cube” in-line and power the active StudioHub+ device via the power cube. DC power on the “Input” side of the cube will be isolated from the Axia PowerStation. The cube will support up to four separate audio Inputs or Outputs. In addition, devices utilizing common audio can be looped together via CAT-5 in/out connectors as audio and power will pass between these units. ® 601 Heron Drive · Logan Township, NJ 08085 (856) 467-8000 · Fax (856) 467-3044 www.studiohub.com www.radiosystems.com