* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download ES205 Lab 4 - Modeling of a Motor-Generator Set - Rose
History of electric power transmission wikipedia , lookup
Opto-isolator wikipedia , lookup
Wireless power transfer wikipedia , lookup
Voltage optimisation wikipedia , lookup
Three-phase electric power wikipedia , lookup
Mains electricity wikipedia , lookup
Power engineering wikipedia , lookup
Rectiverter wikipedia , lookup
Two-port network wikipedia , lookup
Resonant inductive coupling wikipedia , lookup
Alternating current wikipedia , lookup
Electrification wikipedia , lookup
Brushless DC electric motor wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Electric motor wikipedia , lookup
Commutator (electric) wikipedia , lookup
Stepper motor wikipedia , lookup
Brushed DC electric motor wikipedia , lookup
ES205 Lab 4 - Modeling of a Motor-Generator Set (Prelab) Objective The objective of this pre-lab exercise is to construct a Simulink model for a motor-generator set, where both machines are armature-controlled. Nominal system parameters are given . You will use this model for the lab. Introduction: Electric motors and generators are both machines which are used to convert one type of energy into another usable form. In most commercial electric motors and generators, a magnetic field acts as a coupler between a stationary member, called the stator, and a moving member called the rotor. The stator may be made from permanent magnets, which is usually used in smaller machines, or made from coils of wire, which is common in larger machines. The purpose of the stator in an armature controlled motor is to set up a constant magnetic flux through the machine. The rotor contains a number of wire coils, each identical and distributed around the periphery of the rotor. These wire coils on the rotor are called the armature windings. The armature windings are connected to a segmented disk called the commutator. The segmented nature of the commutator acts as a switching mechanism as the rotor turns. At different positions of the rotor, different windings of the armature are connected to the external leads. If electricity is supplied to the leads, then the two magnetic fields which are set up by the stator and the armature will effectively push off of one another. When the armature coils are powered in just the correct sequence, forces are produced which cause the rotor to continually rotate. This is what we call an electric motor. If the leads are connected to a closed circuit when the rotor is manually driven, a current is induced in the wire leads as the armature coils cut through the magnetic flux field supplied by the stator. In this mode of operation the device is called a generator and provides a way to convert rotational mechanical energy back into electrical energy. Simply put, an electric motor and electric generator are essentially the same device. The difference is that the motor converts electrical energy into rotation mechanical energy while a generator converts rotational mechanical energy into electrical energy. A schematic of a coupled motor-generator system is shown in Figure 1. Tg Generator k Motor Bm. Jg +θg, ωg Bg Jm Tm +θm, ωm Figure 1: Schematic of a motor generator system Development of Equations The diagram shown in Figure 2 is a schematic representation for the motor-generator set that will be demonstrated in the lab. The subscripts “M” and “G” refer to motor and generator respectively. The compliance of the shaft is also accounted for on the model with the spring constant, K, in Figure 2. Figure 2: Model of motor generator system The output variables we will consider in this lab will be the armature current, iam, the generator current, iag, the angular velocity of the motor, ωm, the angular velocity of the generator, ωg, and the voltage across the load, vg. Since the machines are armature-controlled, both field currents are assumed to be held constant at their rated values of 0.5 A. The EOM for the motor armature circuit can be obtained using KVL and applying the definition of the back emf to result in − v m + i am R am + L am di am + K e ωm = 0 dt (1) A FBD for the motor rotor is shown in Figure 3. Applying conservation of angular momentum the EOM for the rotor of the motor is given by Jm d 2θm dθ = K t i am − B m − k (θ m − θ g ) 2 dt dt k(θm- θg) B ωm (2) αm Tm=Kt iam Jm +θm, ωm Figure 3: FBD of the motor rotor A FBD for the generator rotor is shown in Figure 4. Applying conservation of angular momentum the EOM for the rotor of the generator is given by Jg d 2θg dt 2 = −K t i ag − B dθ g dt − k (θ g − θ m ) Tg=Kt iag B ωg (3) αg Jg +θg, ωg k(θm- θg) Figure 4: FBD of the generator rotor Applying KVL the EOM for the armature circuit of the generator is given by di ag − K e ω g + i ag R ag + L ag + i ag R L = 0 dt (4) Procedure for drawing a block diagram Take the above numbered equations and develop a simulation diagram for both machines coupled together. Each summing block corresponds to one of the numbered equations, that is (1)-(4). The output of each summing junction is labeled for your convenience. You will need to put the equations in the Laplace domain before you make your diagram. (L am s + R am )i am Σ (Js + B)ω m Σ (Js + B)ω G Σ (R ag + R L + L ag s)i ag Σ Since it is not possible for all the ES205 section to meet in the Power Lab, data was taken by a professor and will be provided for you. The equipment used is shown in Figure 5. Measurement devices Control panel Motor-generator Figure 5: Equipment in the Power Lab. A close-up of the motor-generator is shown in Figure 6. Motor Generator Flexible coupling Figure 6: Close up of the equipment in the Power Lab Nominal values for the system parameters for the motor and generator are shown below: Armature Resistance = 3.33 Ω Armature Inductance = 81.7 mH, Motor Voltage = 120 V, Load Resistance = 85.7 Ω Torque Constant = Voltage Constant = 0.9234 V/(rad/s) when both field currents are at 0.5A Shaft Stiffness = 0.5 N-m/rad, Rotor Inertia = 2.33 x 10-3 kg-m2, Viscous Damping = 6 x 10-4 N-m-sec. Task 1 – Develop a Simulink model Using the nominal values for the system parameters set up a Simulink model which implements your simulation diagram. The input is vm which is applied as a 120 V step at t=0. The output variables are: iam, iag, vg, ωm, and ωg. Be sure not to use any differentiators. Create an m-file to run your Simulink model using the nominal values given and create plots of the five output variables. What you will need to show your professor: • Your hand drawn Simulink Model • You do not need to print out the plots of the output variables, but your instructor will check to see if you have a program that runs at the beginning of the lab period.