Download Module types

Module types
Module type A
Width/Height/Depth: 25,5mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [TE] = 1,3 TE
Module type B
Width/Height/Depth: 45,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [TE] = 2,6 TE
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Module type C
Width/Height/Depth: 67,5mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [TE] = 3,9 TE
Module type D
Width/Heigth/Depth: 135,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [TE] = 7,8 TE
Version 1.0
Module Controller iX800-01
Module dimensions:
evonHOME Module Type D (refer to technical data sheet module
types) Width/Height/Depth: 135,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 7,8 TE
Power supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
System
Microprocessor
Interface LAN
Interface USB 2.0 (USB 4/5)
Interface smartCOM (SC 1/2)
Schnittstelle techCOM
Interface RS232
Interface RS232+RS485
Input
Type
Input supply
Level
Input current
Input frequency
Output
Type
ITH
Switch voltage
Switch current
Short-circuit current
Inner resistance
24 Vdc +/-10 %
max. 5 W
2
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidriv 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
The controller is the heart of the system and provides visualization for all integrated modules.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Freescale i.MX6DL
10-/100-BaseT
Number: 2
Serial bus interface control signals, max.
100m line length between
2 nodes, max. 32 bus users per line
USB Schnittstelle für evonHOME
Technologiemodule
Serial 3 wire interface RS232 (RX/TX), max.
3m line length
Serial 3 wire interface RS232 (RX/TX) and
RS485
4 digital inputs without galvanic separation
for rain, dusk, wind and HomeOff
Refer to power supply
<5 VDC = logic 0
>11 VDC = logic 1
<10mA
max. 25Hz
2 semi-conductor digital outputs, plus switched, short-circuit proof, overtemperature
protected, non-galvanically separated
300mA
Refer to power supply
Max. 300 mA per output
Typically. 6 A per output
Max. 400 mOhm
Commissioning:
•
•
•
•
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g.
iX800) or a converter module S1200 on the lefthand side of the cabinet.
The modules can only be mounted from left to
right.
Plug the included 5-pole smartCOM line connector into the left terminal of the module.
Mount the module on the DIN rail; it will click
when seated correctly.
Push the module along the rail to the left-hand
module in the system. Ensure that the free pins of
the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24
V power supply corresponds to an earth zero
potential!
Once the power is switched on, the power LED
lights up green.
After a few seconds, the bootstrap procedure will
begin (running LED indicator).
As soon as the running LED light is extinguished
and the CPU LED flashes, the bootstrap procedure is complete.
Seite 1/2
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Version 1.1
Module Controller iX800-01
Description:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Notes:
•
•
•
Isolate the system from the mains before beginning commissioning.
Factory reset: The button S1 (16) resets the controller back to the factory settings. WARNING: All configurations will be lost! To reset the controller back to factory settings, keep the button pressed. All LEDs on
the controller will flash. As soon as all LEDs stop flashing and are lit constantly, release the button and the
controller is now reset to factory settings. WARNING: This procedure takes approximately 5 minutes. Do
not interrupt the power supply during this time.
Execute commissioning according to www.evon-home.com
Power supply (24VDC, min 10W)
Digital outputs (Do1, Do2)
Di1: Home Off switch input (predefined, changeable)
Di2: Rain sensor Input (predefined, changeable)
Di3: Input dusk sensor (predefined, changeable)
Di4: Input wind alarm (predefined, changeable)
smartCOM line 2 (line 2) RJ45, not networkable
LAN RJ45 (Internet)
smartCOM line 1 (line 1) Module pin strip, side of housing
USB 4 (e.g. Wi-Fi Kit)
RS485 interface
RS232 interface (only if 11 inactive)
RS232 interface
techCOM Line, side of housing
Reset button (new start controller)
S1 - factory reset button
S2 – system button
Home OFF (2 LEDs)
Red: Active – House Off status on
Green: Active - Di1 input (3) active
19. Rain sensor (2 LEDs)
Red: Active - Rain sensor status active
Green: Active - Di2 input (4) active
20. Dusk sensor (2 LEDs)
Red: Active - Dusk status active
Green: Active - Di3 input (5) active
21. Wind alarm (2 LEDs)
Red: Active – Wind alarm status active
Green: Active - Di4 input (6) active
22. Network LED: Remote access permitted
23. CPU LED: flashes in normal operation
24. SC1 LED: smartCOM line 1 active
25. SC2 LED: smartCOM line 2 active
26. USB 5: USB interface OTG
27. Power LED: Power supply available
Seite 2/2
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Version 1.1
Module Controller iX840-00
Module dimensions:
evonHOME Module Type D (refer to technical data sheet module
types) Width/Height/Depth: 135,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 7,8 TE
Power supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
System
Microprocessor
Interface LAN
Interface USB 2.0 (USB 4/5)
Interface smartCOM (SC 1/2)
Schnittstelle techCOM
Interface RS232
Interface RS232+RS485
Input
Type
Input supply
Level
Input current
Input frequency
Output
Type
ITH
Switch voltage
Switch current
Short-circuit current
Inner resistance
24 Vdc +/-10 %
max. 5 W
2
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidriv 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
The controller is the heart of the system and provides visualization for all integrated modules.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Freescale i.MX6Q
10-/100-BaseT
Number: 2
Serial bus interface control signals, max.
100m line length between
2 nodes, max. 32 bus users per line
USB Schnittstelle für evonHOME
Technologiemodule
Serial 3 wire interface RS232 (RX/TX), max.
3m line length
Serial 3 wire interface RS232 (RX/TX) and
RS485
4 digital inputs without galvanic separation
for rain, dusk, wind and HomeOff
Refer to power supply
<5 VDC = logic 0
>11 VDC = logic 1
<10mA
max. 25Hz
2 semi-conductor digital outputs, plus switched, short-circuit proof, overtemperature
protected, non-galvanically separated
300mA
Refer to power supply
Max. 300 mA per output
Typically. 6 A per output
Max. 400 mOhm
Commissioning:
•
•
•
•
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g.
iX800) or a converter module S1200 on the lefthand side of the cabinet.
The modules can only be mounted from left to
right.
Plug the included 5-pole smartCOM line connector into the left terminal of the module.
Mount the module on the DIN rail; it will click
when seated correctly.
Push the module along the rail to the left-hand
module in the system. Ensure that the free pins of
the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24
V power supply corresponds to an earth zero
potential!
Once the power is switched on, the power LED
lights up green.
After a few seconds, the bootstrap procedure will
begin (running LED indicator).
As soon as the running LED light is extinguished
and the CPU LED flashes, the bootstrap procedure is complete.
Seite 1/2
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Version 1.0
Module Controller iX840-00
Description:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
Notes:
•
•
•
Isolate the system from the mains before beginning commissioning.
Factory reset: The button S1 (16) resets the controller back to the factory settings. WARNING: All configurations will be lost! To reset the controller back to factory settings, keep the button pressed. All LEDs on
the controller will flash. As soon as all LEDs stop flashing and are lit constantly, release the button and the
controller is now reset to factory settings. WARNING: This procedure takes approximately 5 minutes. Do
not interrupt the power supply during this time.
Execute commissioning according to www.evon-home.com
22.
23.
24.
25.
26.
27.
Power supply (24VDC, min 10W)
Digital outputs (Do1, Do2)
Di1: Home Off switch input
Di2: Rain sensor Input
Di3: Input dusk sensor
Di4: Input wind alarm
smartCOM line 2 (line 2) RJ45, not networkable
LAN RJ45 (Internet)
smartCOM line 1 (line 1) Module pin strip, side of housing
USB 4 (e.g. Wi-Fi Kit)
RS485 interface
RS232 interface (only if 11 inactive)
RS232 interface
tecCOM Line (USB 1-3), side of housing
Reset button (new start controller)
S1 - factory reset button
S2 – system button
Home OFF (2 LEDs)
Red: Active – House Off status on
Green: Active - Di1 input (3) active
Rain sensor (2 LEDs)
Red: Active - Rain sensor status active
Green: Active - Di2 input (4) active
Dusk sensor (2 LEDs)
Red: Active - Dusk status active
Green: Active - Di3 input (5) active
Wind alarm (2 LEDs)
Red: Active – Wind alarm status active
Green: Active - Di4 input (6) active
Network LED: Remote access permitted
CPU LED: flashes in normal operation
SC1 LED: smartCOM line 1 active
SC2 LED: smartCOM line 2 active
USB 5: USB interface OTG
Power LED: Power supply available
Seite 2/2
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Version 1.0
Module Blind 1144-00
Module dimensions:
evonHOME module type b (refer to technical data sheet module
types) width/height/depth: 45,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 2,6 HU
Supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Input
Type
Type
Number
Terminals
Rated insulation voltage
Input voltage
Level
Input resistance
Input frequency
Output Relay
Type
Type
Number
Terminals
Rated insulation voltage
ITH
Switch voltage
DC13@24Vdc (EN60947)
AC15@24Vac (EN60947)
AC15@115Vac (EN60947)
AC15@230Vac (EN60947)
Minimum load
Current on terminal L
Mechanical life expectancy
Electrical life expectancy
24 Vdc +/-10 %
max. 2 W
2
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidriv 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Digital input
Potential-free Digital input
4
Up/down T1..T2
250 Vac
See Power supply
<5 VDC = logic 0
>15 VDC = logic 1
min. 3000 Ohm
0…10Hz
Digital output
Potential-free relay contact, closer
4
M Up/down 1..2
250 Vac
5A
12 V..230 Vac/dc
1,5 A
1,5 A
1,5 A
1,5 A
5 V/5 mA
max. 10 A
1x10^7
1x10^5
Intelligent shading module for 2 blinds with separate up and
down motor (230V).
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
•
•
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system. Ensure that the free pins of the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Notes:
•
•
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Larger loads on the module outputs, together with capacitive and inductive
loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
All channel switching functions are available and can be tested after installation (blinds switch up/down activates the blinds motor up/down).
C12 can be used to integrate switches with other potential levels.
Version 1.0
Module Blind 1244-00
Module dimensions:
evonHOME module type c (refer to technical data sheet module
types) width/height/depth: 67,5mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 3,9 HU
Supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Input
Type
Type
Number
Terminals
Rated insulation voltage
Input voltage
Level
Input current
Input frequency
Output
Type
Type
Number
Terminals
Rated insulation voltage
ITH
Switch voltage
DC13@24Vdc (EN60947)
AC15@24Vac (EN60947)
AC15@115Vac (EN60947)
AC15@230Vac (EN60947)
Minimum load
Current on terminal L
Mechanical life expectancy
Electrical life expectancy
24 Vdc +/-10 %
max. 2 W
2
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidriv 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Digital input
Potential-free Digital input
4
Up/down T1..T2
250 Vac
See Power supply
<6 VDC = logic 0
>7 VDC = logic 1
7,5 mA
0…10Hz
Digital output
Potential-free relay contact, closer
4
M Up/down 1..2
250 Vac
16 A
12 V..230 Vac/dc
1,5 A
3A
3A
3A
5 V/5 mA
max. 16 A
1x10^7
1x10^5
Intelligent shading module for 2 blinds with reversing DC
motor
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
•
•
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system. Ensure that the free pins of the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Notes:
•
•
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Check the load of DC motors. If necessary, decouple using relays.
The input channel may only be switched with 24 V DC.
All channel switching functions are available and can be tested after installation (blinds switch up/down activates the blinds motor up/down).
C1/C2 can be used to integrate switches with other potential levels.
Version 1.0
Modul Blind 1344-00
Module dimensions:
evonHOME module type b (refer to technical data sheet module
types) width/height/depth: 45,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 2,6 HU
Supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Input
Type
Type
Number
Terminals
Rated insulation voltage
Input voltage
Level
Input resistance
Input frequency
Output Relay
Type
Type
Number
Terminals
Rated insulation voltage
ITH
Switch voltage
DC13@24Vdc (EN60947)
AC15@24Vac (EN60947)
AC15@115Vac (EN60947)
AC15@230Vac (EN60947)
Minimum load
Current on terminal L
Mechanical life expectancy
Electrical life expectancy
24 Vdc +/-10 %
max. 2 W
2
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidriv 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Digital input
Potential-free Digital input
4
Up/down T1..T2
250 Vac
See Power supply
<5 VDC = logic 0
>15 VDC = logic 1
min. 3000 Ohm
0…10Hz
Digital output
Potential-free relay contact, closer
4
M Up/down 1..2
250 Vac
5A
12 V..230 Vac/dc
1,5 A
1,5 A
1,5 A
1,5 A
5 V/5 mA
max. 10 A
1x10^7
1x10^5
Intelligent shading module for 2 blinds with separate up and
down motor (230V).
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
•
•
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system. Ensure that the free pins of the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Notes:
•
•
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Larger loads on the module outputs, together with capacitive and inductive
loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
All channel switching functions are available and can be tested after installation (blinds switch up/down activates the blinds motor up/down).
C12 can be used to integrate switches with other potential levels.
Version 1.1
Module Light 1144-00
Module dimensions:
evonHOME module type b (refer to technical data sheet module
types) width/height/depth: 45,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 2,6 HU
Supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Input
Type
Type
Number
Terminals
Rated insulation voltage
Input voltage
Level
Input resistance
Input frequency
Output
Type
Type
Number
Terminals
Rated insulation voltage
ITH
Switch voltage
DC13@24Vdc (EN60947)
AC15@24Vac (EN60947)
AC15@115Vac (EN60947)
AC15@230Vac (EN60947)
Minimum load
Current on terminal L
Mechanical life expectancy
Electrical life expectancy
24 Vdc +/-10 %
max. 2 W
2
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidriv 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Digital input
Potential-free digital input
4
T1..T4
250 Vac
See Power supply
<5 VDC = logic 0
>15 VDC = logic 1
min. 3000 Ohm
0…10Hz
Digital output
Potential-free relay contact, closer
4
L1..L4
250 Vac
5A
12 V..230 Vac/dc
1,5 A
1,5 A
1,5 A
1,5 A
5 V/5 mA
max. 10 A
1x10^7
1x10^5
Intelligent lighting modules for 4 light functions. Installation
with additional power relays.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
•
•
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system. Ensure that the free pins of the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Notes:
•
•
•
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Larger loads on the module outputs, together with capacitive and inductive
loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
All channel switching functions are available and can be tested after installation (switch light on/off switches Light On/Off ).
Inputs can be configured for proximity sensors or switches.
C14 can be used to integrate switches with other potential levels.
Version 1.0
Module Light 1244-00
Module dimensions:
evonHOME module type C (refer to technical data sheet module
types) width/height/depth: 67,5mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 3,9 HU
Supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Input
Type
Type
Number
Terminals
Rated insulation voltage
Input voltage
Level
Input resistance
Input frequency
Output
Type
Type
Number
Terminals
Rated insulation voltage
ITH
Switch voltage
Bulb load
Capacitive load (EN60669-1)
Load acc. to EN60669-1
Minimum load
Current on terminal L
Mechanical life expectancy
Electrical life expectancy
24 Vdc +/-10 %
max. 2 W
2
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidriv 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Digital input
Potential-free Digital input
4
T1..T4
250 Vac
See power supply
<0,5 VDC = logic 0
>8 VDC = logic 1
min. 11.500 Ohm
0…5Hz
Digital output
Potential-free relay contact, closer
4
L1..L4
250 Vac
5A
12 V..230 Vac/dc
3000 W, 240 VAC, rel. ED 8,3%
16 A, 240 VAC, capacitive load140 μF, 7,5
min-1
12 A, 264 VAC, cosϕ=0,6
12 V/5 mA
max. 10 A
3x10^6
2x10^4
Intelligent lighting module for 4 light functions. With integrated relays up to 5 A.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
•
•
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system. Ensure that the free pins of the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Notes:
•
•
•
•
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Use the same phase for all roots in a module.
Larger loads on the module outputs, together with capacitive and inductive
loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
All channel switching functions are available and can be tested after installation.
Light inputs can be configured for proximity sensors or switches.
C12/C34 can be used to integrate switches with other potential levels.
Version 1.0
Modul Light 1424-00
Module dimensions:
evonHOME module type C (refer to technical data sheet module
types) width/height/depth: 67,5mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 3,9 HU
Supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Input
Type
Type
Number
Terminals
Rated insulation voltage
Input voltage
Level
Input resistance
Input frequency
Output Digital
Type
Type
Number
Terminals
Rated insulation voltage
ITH
Switch voltage
Minimum load
Current on terminal L
Mechanical life expectancy
Electrical life expectancy
Analog Output
Type
Type
Number
Terminals
Resolution
Current
24 Vdc +/-10 %
max. 2 W
2
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidriv 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Digital input
Potential-free Digital input
4
T1..T4
250 Vac
See power supply
<12 VDC = logic 0
>19 VDC = logic 1
min. 10.500 Ohm
0…5Hz
Digital output
Potential-free relay contact, closer
2
Do1..Do2
250 Vac
10 A
12 V..230 Vac/dc
5 V/5 mA
Max. 30 A, max. 10 A (continuous)
1x10^7
7x10^4
Analog output
Voltage output 0..10V
2
Ao1..2
12 Bit (accuracy < 2%)
max. 5 mA
Intelligent dimmer module for 2 light functions. For 0 (1) up
to 10 V controllable dimmer pack.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
•
•
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system. Ensure that the free pins of the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Anmerkungen:
•
•
•
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Larger loads on the module outputs, together with capacitive and inductive
loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
All channel switching functions are available and can be tested after installation.
C12/C34 can be used to integrate switches with other potential levels.
The inputs T3 and T4 can be used as digital inputs.
Version 1.0
Module Light 1544-00
Module dimensions:
evonHOME module type C (refer to technical data sheet module
types) width/height/depth: 45,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 2,6 HU
Supply
Power supply
Nominal consumption
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Input
Type
Type
Number
Terminals
Input voltage
Level
Input frequency
Analog Output
Type
Type
Number
Terminals
Resolution
Output current per output
Max. recommended cable length
Accuracy (without load)
24 Vdc +/-10 %
max. 2 W
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+55°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidriv 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Intelligent dimmer module for 4 light functions. For 0 up to
10 V controllable dimmer pack without additional release.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
Digital input
Potential-free Digital input
4
T1..T4
See power supply
logic 0 < 5Vdc
logic 1 > 15Vdc
250Hz
•
•
Analog output
Voltage output 0..10 V
4
Ao1..4
2000 Digit
max. 10 mA
30 m
type 0,1 % +30 mV max. 0,6 % + 100 mV
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system. Ensure that the free pins of the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Notes:
•
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Larger loads on the module outputs, together with capacitive and inductive
loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
All channel switching functions are available and can be tested after installation.
Version 1.7
Module Light 1644-00
Intelligent LED module for the control of 4 white LED strips or
1 RGBW LED strip.
Modulabmessungen:
evonHOME Modultype C (siehe Technisches Blatt Modultypen)
Breite/Höhe/Tiefe: 67,5 mm/85,0 mm/70,0 mm
Schraubsockeltiefe 38,5 mm Teilungseinheiten [TE] = 3,9 TE
Supply
Power supply
Nominal consumption
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Input
Type
Type
Number
Terminals
Rated insulation voltage
Input voltage
Level
Input resistance
Input frequency
Max. recommended cable length
LED output
Type
LED type
Cable shielding required
Number
Contacts
Current
Max. recommended cable length
Relay output
Type
Number
Overvoltage category
Assessment category
Max. current
Switch on current
Switch voltage
24 Vdc +/-10 %
max. 2 W
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+55°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidrive 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Digital input
Potential-free digital input
4
T1..T4
250 Vac
See Power supply
<5 VDC = logic 0
>15 VDC = logic 1
min. 10.500 Ohm
0…10 Hz
30 m
Open collector semiconductor without
galvanic separation (PWM)
Common anode
No
4
1(R) 2(G) 3(B) 4(W)
max. 5 A pro Ausgang Only for resistance
and diode loads (current-limited)
30 m
Potential-free relay contact, closer
1
2
250 Vac
12 A
max. 120 A max. 20 ms
12 V..230 V AC/DC
ATTENTION: ELECTRICAL VOLTAGE
Disconnect all system components from the mains before commencing work. The wiring of the components may ONLY be carried out in a potential-free state. The wiring may only be carried out by trained
expert personnel.
Important before commissioning:
•
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger ohmic loads as well as capacitive and inductive loads on the module outputs must be switched via relays.
The input channel may only be switched with 24 V DC.
Please note the required minimum cross-sections (see calculation on page 2)
Wiring example:
Commissioning:
•
•
•
•
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system.
Ensure that the free pins of the connector snap into place in the socket of
the adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Notes:
•
•
•
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Only use LED strips of type “common anode”.
The digital output (DO1) can be used as a free switch contact for the external power supply.
Larger ohmic, capacitive and inductive loads on the module output must
be switched via relays.
The input channel may only be switched with 24 V DC.
All channel switching functions are available and can be tested after installation.
Version 1.7
Module Light 1644-00
Wire/Cable cross-section calculation LED:
(between device and LED strip)
A=
A
I
lW
VS
Kd
56
Intelligent LED module for the control of 4 white LED strips or
1 RGBW LED strip.
Wire/Cable calculation power supply:
(between power supply and device)
I * lW
A=
VS * Kd * 56
cross-section [mm²]
current [A]
Wire length (length of plus and minus wire) [m]
Power supply voltage [V]
Voltage decrease as factor
For plus wire :
0,01 = recommended (=1%)
0,02 = maximum (=2%)
For minus wire :
0,01 = recommended (=1%)
0,05 = maximum (=5%)
Electrical conductivity of copper [m/(R*mm²)]
I * lW
VS * Kd * 56
cross-section [mm²]
current [A]
Wire length (length of plus and minus wire) [m]
Power supply voltage [V]
Voltage decrease as factor
0,01 = recommended (=1%)
0,02 = maximum (=2%)
Electrical conductivity of copper [m/(R*mm²)]
A
I
lW
VS
Kd
56
Example :
Example :
ILED = 2 A / lW = 5 m / VS=24 Vdc / Kd=0,01
I = 10 A / lW = 2 m / VS=24 Vdc / Kd=0,01
Number of LED strips: 4
A=
Calculation plus wire
4 * 2 A = 8 A (one plus wire for all LED strips)
A=
8*5
24 * 0,01 * 56
10 * 2
24 * 0,01 * 56
=1,488 mm2
Wire or cable used with a cross-section of 1,5 mm²
=2,9762 mm2
Wire or cable used with a cross-section of 4 mm²
Calculation minus wire
A=
2*5
24 * 0,01 * 56
=0,744 mm2
Wire or cable used with a cross-section of 1 mm²
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Version 1.7
Module Clima 1144-00
Module dimensions:
evonHOME module type b (refer to technical data sheet module
types) width/height/depth: 45,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 2,6 HU
Supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Input
Type
Type
Number
Terminals
Rated insulation voltage
Input voltage
Level
Input resistance
Input frequency
Output
Type
Type
Number
Terminals
Rated insulation voltage
ITH
Switch voltage
DC13@24Vdc (EN60947)
AC15@24Vac (EN60947)
AC15@115Vac (EN60947)
AC15@230Vac (EN60947)
Minimum load
Current on terminal L
Mechanical life expectancy
Electrical life expectancy
24 Vdc +/-10 %
max. 2 W
2
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidrive 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Digital input
Potential-free digital input
4
FBR1..4
250 Vac
See power supply
<9 VDC = logic 0
>19 VDC = logic 1
min. 3000 Ohm
0…10kHz
Digital output
Potential-free relay contact, closer
4
Ventil1..4
250 Vac
5A
12 V..230 Vac/dc
1,5 A
1,5 A
1,5 A
1,5 A
5 V/5 mA
max. 10 A
1x10^7
1x10^5
Intelligent room climate module with 4 heating circuits.
Connection-ready for evon room control units.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
•
•
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system. Ensure that the free pins of the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Notes:
•
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Use control valve normally closed (NC 230V or NC 24V).
An evon room control unit C110X must be connected to the input channel.
All channel functions are available and can be tested after installation
(comfort mode, energy saving mode, frost protection mode).
Version 1.0
Module Clima 1244-00
Module dimensions:
evonHOME module type b (refer to technical data sheet module
types) width/height/depth: 45,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 2,6 HU
Supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Input
Type
Type
Number
Terminals
Rated insulation voltage
Measurement current
Measurement range
Resolution
Sample rate
Accuracy
Output
Type
Type
Number
Terminals
ITH
Switch voltage
Switch current
Short circuit current
Inner resistance
24 Vdc +/-10 %
max. 2 W
2
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidrive 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Analog input
PT1000 inputs connected in series
4
B1..B4
No galvanic isolation to supply voltage
< 300 µA
-50...+300°C
0,1K
0,9S/s
+/- 0,15% (corresponds to 0,4K) @25°C
Digital output
Semiconductor, positive switching, short-circuit proof. Overtemperature protection, not
galvanically isolated
4
Valve1..4
1,3A
See power supply
Max. 800mA pro Output
Typically 6A per output
max. 400 mOhm
Intelligent room climate module with 4 heating circuits.
Connections for PT1000 sensors.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
•
•
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system. Ensure that the free pins of the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Notes:
•
•
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Use control valve normally closed (NC 24V).
Series-connected PT1000 sensors must be connected to all module inputs
(see wiring example).
All channel functions are available and can be tested after installation
(comfort mode, energy saving mode, frost protection mode).
Unused PT1000 sensor inputs must be bridged.
Version 1.0
Module Clima 1244-01
Module dimensions:
evonHOME module type B (refer to technical data sheet module
types) width/height/depth: 45,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 2,6 HU
Supply
Power supply
Nominal consumption
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Input
Type
Type
Number
Terminals
Rated insulation voltage
Measurement current
Measurement range
Resolution
Signal delay
Accuracy
Output
Type
Type
Number
Terminals
Rated insulation voltage
Switch voltage
DC13@24Vdc (EN60947)
AC15@24Vac (EN60947)
AC15@115Vac (EN60947)
AC15@230Vac (EN60947)
Minimum load
Mechanical life expectancy
Electrical life expectancy
24 Vdc +/-10 %
max. 2 W
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidrive 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Intelligent room climate module with 4 heating circuits.
Connections for PT1000 sensors.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
Analog input
PT1000 inputs connected in series
4
B1..B4
No galvanic isolation to supply voltage
< 700 µA
-200...+320°C
0,1K
nom. 640 ms
0,2K
•
•
Digital output
Potential-free relay contact, closer
4
Valve 1 .. 4
250 Vac
12 V .. 230 Vac/dc
1,5 A
1,5 A
1,5 A
1,5 A
5 V/5 mA
1 x 10^7
1x10^5
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system. Ensure that the free pins of the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Notes:
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Use valves normally closed (NC).
All channel functions are available and can be tested after installation
(comfort mode, energy saving mode, frost protection mode).
Version 1.6
Room Control Unit C110X-00
Module dimensions:
Width/Height/Depth: 84,5mm/84,5mm/25,0mm
Supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Temperature measurement
Accuracy
24 Vdc +/-10 %
50 mW
2
100%
Room temperature sensor and operating panel with data
protocol for C1144 Modules.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work. The wiring of the components may ONLY be carried out in a potential-free state. The wiring may only be carried out by trained
expert personnel.
Mounting:
Wiring example:
+24V
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Phillips Ne.2
0,5 Nm
IP 20
CE
+25°C: +/- 0,5°C
-10..+85°C: +/-1°C
Dimensions:
FBR1
FBR2
FBR3
FBR4
..
FBRn
Opening the unit:
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Polarity reversal protection
Front view:
(Maximum configuration C1103)
Version 1.0
Module dimensions :
Flush mounted stakes 50 x 50 mm
Width/Height/Depth: 50mm/50mm/8mm
Adapter frame (50mm x 50mm) needed.
Supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Measurement
Accuracy
24 Vdc +/-10 %
Max. 40 mW
2
100%
evonHOME touch room temperature sensor and operating
panel in 2-wire-technology to be connected to C1144
module.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Wiring example:
Mounting:
+24V
-20..+60°C, 10..95 % rH, noncondensing
-20..+60°C, 10..95 % rH, noncondensing
2
AWG 22 ... 18, 0.34 mm² ... 0,75 mm²
Spring-cage terminal block
6 mm ... 7 mm
IP 30
CE
+5°C ... 60°C l +/-0.5°C
0% ... 100% rH l 4% rH noncondensing
O6 0
FBR1
FBR2
FBR3
FBR4
...
FBRn
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
70,7
Sensor C1109-00
70,7
Version 1.1
Sensor C1010-00
PT1000 Sensor for connection to modules A1240, A1380,
C1244.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Sensor
Type
Accuracy
Sensor voltage
Overvoltage protection
Recommended measurement
current
Duty cycle
Housing
Dimensions
Protection type (EN 60529)
Mounting
Weight
Terminals
Type
Tools
Terminal capacity
Wire stripping length
Contact resistance
Tests/Certification
Environmental conditions
Recommended processing temperature
Environmental temperature (operational)
Relative humidity (operational)
Storage capability
Pollution degree( EN 60664-1)
PT1000-B
EN60751 F0.3 (0,3+0,005x|t|)
|t| temperature in °C without sign
-70°C 0,65K
0°C 0,3K
100°C 0,80K
max. 15V
Internal ESD protection
0,1..0,3mA
max. 2mA
100%
Wiring example:
Notes:
•
•
Standard sensor PT1000 bipolar is used with modules A1240, A1380 and
C1244.
Connections are reverse-polarity protected.
10 x 25 x 7 mm
IP00
Using glue, surface must be free of dust and
grease.
1,3g
Spring-loaded terminal
Pen, screwdriver
AWG 22..18
single core, 0,34..0,75mm²
finely stranded, 0,34..0,75mm²
6..7mm
<20mOhm
CE
+18°C..+35°C
-40°C..+80°C
10..95%rH, non-condensing
12 Mon. @+23°C; 20..70%rH
1
Example: Sensor C1010 connected to module
Analog 1380 (also possible to module Clima 1244
and Analog 1240).
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Version 1.0
Module Digital 1180-00
Module dimensions:
evonHOME module type b (refer to technical data sheet module
types) width/height/depth: 45,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 2,6 HU
Supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Input
Type
Type
Number
Terminals
Rated insulation voltage
Input voltage
Level
Input resistance
Input frequency
24 Vdc +/-10 %
2W
2
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidrive 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Digital input
Potential-free digital input
8
Di 1..8
250 Vac
siehe Versorgungsspannung
<5 VDC = logic 0
>15 VDC = logic 1
min. 3000 Ohm
0…10kHz
Universal digital module for 8 digital inputs. For the connection of window contacts and proximity sensors, etc.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
•
•
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system. Ensure that the free pins of the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Note:
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
The input channel may only be switched with 24 V DC.
Version 1.0
Module Digital 1208-00
Module dimensions:
evonHOME module type b (refer to technical data sheet module
types) width/height/depth: 45,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 2,6 HU
Supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Output
Type
Type
Number
Terminals
Rated insulation voltage
ITH
Switch voltage
DC13@24Vdc (EN60947)
AC15@24Vac (EN60947)
AC15@115Vac (EN60947)
AC15@230Vac (EN60947)
Minimum load
Current on terminal L
Mechanical life expectancy
Electrical life expectancy
24 Vdc +/-10 %
2W
2
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidrive 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Digital output
Potential-free relay contact, closer
8
Do 1..8
250 Vac
5A
12 V..230 Vac/dc
1,5 A
1,5 A
1,5 A
1,5 A
5 V/5 mA
max. 5 A
1x10^7
1x10^5
Universal digital module for 8 digital outputs. For the connection of alarm sirens, door openers, etc.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
•
•
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system. Ensure that the free pins of the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Notes:
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Larger loads on the module outputs, together with capacitive and inductive
loads, must be switched via relays.
C14/C58 can be used to integrate outputs with other separated potential
levels..
Version 1.0
Module Digital 1344-00
Module dimensions:
evonHOME module type b (refer to technical data sheet module
types) width/height/depth: 45,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 2,6 HU
Supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Input
Type
Type
Number
Terminals
Rated insulation voltage
Input voltage
Level
Input resistance
Input frequency
Output
Type
Type
Number
Terminals
Rated insulation voltage
ITH
Switch voltage
DC13@24Vdc (EN60947)
AC15@24Vac (EN60947)
AC15@115Vac (EN60947)
AC15@230Vac (EN60947)
Minimum load
Current on terminal L
Mechanical life expectancy
Electrical life expectancy
24 Vdc +/-10 %
1W
2
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidrive 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Digital input
Potential-free digital input
4
Di 1..4
250 Vac
See power supply
<5 VDC = logic 0
>15 VDC = logic 1
min. 3000 Ohm
0...2Hz
Digital output
Potential-free relay contact, closer
4
Do 1..4
250 Vac
5A
12 V..230 Vac/dc
1,5 A
1,5 A
1,5 A
1,5 A
5 V/5 mA
max. 5 A
1x10^7
1x10^5
Universal digital module for 4 digital inputs and 4 digital
outputs.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
•
•
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system. Ensure that the free pins of the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Notes:
•
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
The input channel may only be switched with 24 V DC.
Larger loads on the module outputs, together with capacitive and inductive
loads, must be switched via relays.
DoC can be used to integrate outputs with other separated potential levels.
Version 1.0
Module Analog 1144-00
Module dimensions:
evonHOME module type b (refer to technical data sheet module
types) width/height/depth: 45,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 2,6 HU
Supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Input
Type
Type
Number
Terminals
Rated insulation voltage
24 Vdc +/-10 %
2W
2
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidrive 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Analog input
Voltage input
4
Ai1..Ai4
No galvanic insulation to supply voltage
Measurement range
Measurement current
Resolution
Sampling interval
Output
Type
Type
Number
Terminals
Rated insulation voltage
0..10V
0,5 mA@10V
10Bit
10S/s
Output voltage
Output current
Resolution
0..10V
max. 5mA
12Bit
Analog output
Voltage output
4
Ao1..Ao4
No galvanic insulation to supply voltage
Universal analog module with 0… 10 V input and output
channels.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
•
•
•
•
•
•
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system. Ensure that the free pins of the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Version 1.0
Modul Analog 1240-00
Module dimensions:
evonHOME module type b (refer to technical data sheet module
types) width/height/depth: 45,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 2,6 HU
Supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Input
Type
Type
Number
Terminals
Rated insulation voltage
Input voltage
Measurement range
Measurement current
Resolution
Sampling interval
Accuracy
24 Vdc +/-10 %
2W
2
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidrive 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Analog input
PT1000 inputs connected in series
4
B1..B4
No galvanic insulation to supply voltage
No voltage may be applied
-50..+300°C
<300µA
0,1K
0,9S/s
+/- 0,15% (corresponds to 0,4K)@+25°C
Universal analog module for temperature measurement using
4 PT1000 sensors.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
•
•
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system. Ensure that the free pins of the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Notes:
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Series-connected PT1000 sensors must be connected to all module inputs
(see wiring example).
Unused PT1000 sensor inputs must be bridged.
Version 1.0
Modul Analog 1240-01
Module dimensions:
evonHOME module type b (refer to technical data sheet module
types) width/height/depth: 45,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 2,6 HU
Supply
Power supply
Nominal consumption
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Input
Type
Type
Number
Terminals
Rated insulation voltage
Input voltage
Measurement range
Measurement current
Resolution
Signal delay
Accuracy
24 Vdc +/-10 %
2W
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidrive 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Analog input
PT1000 inputs connected in series
4
B1..B4
No galvanic insulation to supply voltage
No voltage may be applied
-200..+320°C
<700µA
0,1K
nom. 640 ms
0,2K
Universal analog module for temperature measurement using
4 PT1000 sensors.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
•
•
•
•
•
•
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system. Ensure that the free pins of the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Version 1.6
Module Analog 1380-00
Module dimensions:
evonHOME module type b (refer to technical data sheet module
types) width/height/depth: 45,0mm/85,0mm/70,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 2,6 HU
Supply
Power supply
Nominal consumption
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Terminals
Terminal capacity
Screws
Tightening torque
Protection type (EN 60529)
Tests/Certification
Input
Type
Type
Number
Terminals
Rated insulation voltage
Input voltage
Measurement range
Measurement current
Resolution
Sampling interval
Accuracy
24 Vdc +/-10 %
2W
2
100%
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
max. 2 x 1,5 mm²
Pozidriv 1 / Slot 4 x 0,8 mm
0,4 Nm
IP 20
CE
Analog input
PT1000/KTY81-110/KTY81-210 inputs with
joint reference point
8
B1..B8
No galvanic insulation to supply voltage
No voltage may be applied
-50..+150°C
500..900 µA
0,1K
0,78S/s (filter delay time = x10)
< 0,1K @+25°C
Universal module for temperature measurement using 8
PT1000 or KTY sensors.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
•
•
•
•
•
•
•
•
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system. Ensure that the free pins of the connector snap into place in the socket of the
adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Once the power is switched on, the ON LED lights up green.
The smartCOM LED flashes red.
Once the controller has recognized and addressed the modules, the smartCOM red LED is extinguished and the allocation and configuration can
begin via the visualization.
Notes:
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
PT1000, KTY81-110 and KTY81-210 sensors. Can be connected to the module inputs.
Version 1.0
Module Sound TS410-00
The evonHome sound module controls background musik
and speech output - in 2 zones (stereo) or in up to 4 zones
(mono).
Module dimensions :
evonHOME module type C (see technical data sheet module types)
width/height/depth: 67,5mm/85,0mm/70,0mm
Screw socket depth 38.5 mm Module width (TE) = 3.9 TE
Power supply
Supply voltage
24 Vdc +/-10 %
Duty cycle
100%
Environmental conditions
Operating conditions
-15..+55°C
Storage conditions
-25..+70°C
Degree of contamination
2
Connectors
Connector capacity
0,25 mm² ... 4 mm²
Type
Screw connector
Stripping length
7 mm ... 8 mm
Protection class (EN60259)
IP 30
Test/Approvals
CE
Inputs
Aerial for FM radio
F-socket on device (75 Ohm)
AUX input
on connector (stereo 11 kOhm)
Outputs (class D amplifier)
Type
2 x stereo or 4 x mono
Protective circuit
Overtemperature and short-circuit protection
Peak output power per channel (at 24V DC)
4 Ohm: 42W Max (THD+N 10%@1kHz)
8 Ohm: 25W Max (THD+N 10%@1kHz)
4 Ohm: 33W Max = 23W RMS (THD+N 1%@1kHz)
8 Ohm: 20W Max = 14W RMS (THD+N 1%@1kHz)
4 Ohm: <5W (THD+N <0.1%@1kHz)
8 Ohm: <3W (THD+N <0.1%@1kHz)
THD+N: Total Harmonic Distortion + Noise
Continuous output power per channel (at 24V DC and +20°C)
4 Ohm: 10W Derating: 0,28W per °C (+20°C .. + 55°C)
8 Ohm: 25W Derating: 0,7W per °C (+20°C .. + 55°C)
Recommended wiring
Load
Power
Length
Minimum
cross-section
4/8Ohm
up to 5W
up to 3m
0,75mm²
4/8Ohm
up to 5W
from 3m up to 10m 0,75mm²
4/8Ohm
up to 5W
from 10m up to 30m 1,5mm²
4/8Ohm
over 5W
up to 3m
1,5mm²
4/8Ohm
over 5W
from 3m up to 10m 2,5mm²
4/8Ohm
over 5W
from 10m up to 30m 4mm²
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply each module with power.
Please check whether ground corresponds to earth-zero potential.
Only use loudspeakers with 4 or 8 Ohms. Only a maximum of two 8 Ohm loudspeakers can be connected in parallel otherwise the output stage of the amplifier can be damaged.
To ensure better reception, the antenne cable (75 Ohms) should fed outside the circuit cabinet.
Wiring example:
Commissioning:
•
•
•
•
•
Commissiong may only commence if power has been disconnected.
Technology modules are to be installed to the left of the CPU.
Mount the module on the top hat rail, ensure it clicks into place.
Please check that the GND supply of your 24V power supply corresponds
to earth zero-potential!
The module will be recognised automatically and can be controlled/configured via the usual user interface.
Notes:
•
•
Larger cross-sections must be used for longer cable paths (loudspeaker).
techCOM-Modules must be installed in the same cabinet as the controller
(max. 1.5m with extension from controller)
(1) Green - Ready / Red - Common error
(2/3) Green - Amplifier 1/2 active / Red - Amplifier 1/2 error
(4/5/6/7) Speaker 1 - 4 active
(8) FM - Radio active
(9) Power supply ok
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Version 1.0
Module Auxiliary TA200-00
evonHOME techCOM-module to extend the controller with
two additional RS485 interfaces.
Module dimensions :
evonHOME module type B (see technical data sheet module types)
width/height/depth: 45,0mm/85,0mm/70,0mm
Screw socket depth 38.5 mm Module width (TE) = 2,6 TE
Power supply
Supply voltage
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Degree of contamination
Connectors
Connector capacity
Type
Stripping length
Protection class (EN60259)
Test/Approvals
Interface
Type
Quantity
Galvanic isolation
Isolation voltage
Interface voltage
Baudrate
Support
Internal bus termination
Protection circuit
Max. cable length
24 Vdc +/-10 %
100%
-15..+55°C
-25..+70°C
2
0,25 mm² ... 4 mm²
Screw connector
7 mm ... 8 mm
IP 20
CE
RS485
2
yes
2,2 kVac functional insulation
5V
300..250k
7..8 Databits
1..2 Stopbits
odd, even, mark, space and no parity
yes
PTC in series, over voltage protection
depends on cable and environment, see
RS485 specification
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
Supply each module with power.
Please check whether ground corresponds to earth-zero potential.
Wiring example:
Commissioning:
•
•
•
•
•
Commissiong may only commence if power has been disconnected.
Technology modules are to be installed to the left of the CPU.
Mount the module on the top hat rail, ensure it clicks into place.
Please check that the GND supply of your 24V power supply corresponds
to earth zero-potential!
The module will be recognised automatically and can be controlled/configured via the usual user interface.
Notes:
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
techCOM-modules must be installed in the same cabinet as the controller
(max. 1.5m with extension from controller)
Version 1.0
Module Auxiliary TA200-00
evonHOME techCOM-module to extend the controller with
two additional RS485 interfaces.
Module dimensions :
evonHOME module type B (see technical data sheet module types)
width/height/depth: 45,0mm/85,0mm/70,0mm
Screw socket depth 38.5 mm Module width (TE) = 2,6 TE
Power supply
Supply voltage
Overvoltage category
Duty cycle
Environmental conditions
Operating conditions
Storage conditions
Degree of contamination
Connectors
Connector capacity
Type
Stripping length
Protection class (EN60259)
Test/Approvals
Interface
Type
Quantity
Galvanic isolation
Isolation voltage
Interface voltage
Baudrate
Support
Internal bus termination
Protection circuit
Max. cable length
24 Vdc +/-10 %
2
100%
-15..+55°C
-25..+70°C
2
0,25 mm² ... 4 mm²
Screw connector
7 mm ... 8 mm
IP 20
CE
RS485
2
yes
2,2 kVac
5V
300..250k
7..8 Databits
1..2 Stopbits
odd, even, mark, space and no parity
yes
PTC in series, over voltage protection
depends on cable and environment, see
RS485 specification
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply each module with power.
Please check whether ground corresponds to earth-zero potential.
Only use loudspeakers with 4 or 8 Ohms. Only a maximum of two 8 Ohm loudspeakers can be connected in parallel otherwise the output stage of the amplifier can be damaged.
To ensure better reception, the antenne cable (75 Ohms) should fed outside the circuit cabinet.
Wiring example:
Commissioning:
•
•
•
•
•
Commissiong may only commence if power has been disconnected.
Technology modules are to be installed to the left of the CPU.
Mount the module on the top hat rail, ensure it clicks into place.
Please check that the GND supply of your 24V power supply corresponds
to earth zero-potential!
The module will be recognised automatically and can be controlled/configured via the usual user interface.
Notes:
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
techCOM-modules must be installed in the same cabinet as the controller
(max. 1.5m with extension from controller)
Version 1.0
Module Sys 2200/2300/2400-00
Module dimensions:
evonHOME module type b (refer to technical data sheet module
types) width/height/depth: 22,5mm/85,0mm/65,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 1,3 HU
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Schutzart (EN 60529)
Tests/Certification
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
IP 50
CE
techCOM extender module
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
The input channel may only be switched with 24 V DC.
Wiring example:
Commissioning:
•
•
•
•
•
Isolate the system from the mains before beginning
commissioning.
The modules can only be mounted from right to left.
Plug the included 8-pole techCOM line connector into
the left terminal of the controller (iX800/iX840).
Mount the module on the DIN rail; it will click when
seated correctly.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Notes:
•
•
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
techCOM Extender from Sys 2300 to Sys 2400.
Max. techCOM line length 1,5m.
techCOM line can only be extended once
Only line topology is supported
Version 1.1
Module Sys 100W-00
Module dimensions:
Width/height/depth: 90,0mm/96,0mm/56,2mm
Horizontal pitch [U] = 5,2 HU
Supply
Input voltage
Consumption
Input frequency
Rated insulation voltage
Internal fuse
Output
Voltage
Minimum permissible load
Temperature coefficient
Current
Line balancing
Load matching
Efficiency
Overpower protection
Overvoltage protection
Environmental conditions
Operating conditions
Storage conditions
Terminals
Type
Terminal capacity
Tightening torque
Tests/Certification
100..240VAC
max. 2.2A
47..63Hz
3000 Vac (4242 VDC)
T3, 15A 250VAC
Switching power supply 230VAC/24VDC 100 W 4.2A
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Wiring example:
Connection to mains:
Connection to the mains supply is via the terminals L and N (see wiring example) and must
be done according to IEC 60364 and EN 50178. A system for protection must be provided for
(circuit breaker or power switch) and an isolating device must be available to activate the power
supply. A ground fault circuit interrupter (FI) should not be used as the only protective mechanism for indirect contact: This is true for the entire mains protected by the FI protective switch.
Mains-side fusing (IEC 898):
24..28VDC
0%
+/- 0.03%/°C
max. 4,2A
+/- 1%
+/- 1%
89%
110-150%
min 30V / max 33V
•
•
-25..+71°C
-25..+85°C
Note:
Schrauben
max. 2 x 1,5 mm²
0,6 Nm
cULus, EAC
Circuit breaker characteristic C, from 10 A
Circuit breaker characteristic B, from 16 A
Further country-specific regulations may need to be observed.
Output connections:
Connecting the output voltage is done via the terminals “+” and “-“ on the power supply (see wiring example). Please ensure that the output cables are dimensioned according to the maximum
effective value of the output current, or are additionally fused.
When used together with devices with a protection class I (with protective earth), a connection
between “-“ and “PE” must be made with at least 1,5 mm2.
Module dimensions:
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Version 1.0
Module Sys 1100-00
Module dimensions:
evonHOME module type B (refer to technical data sheet module
types) Width/Height/Depth: 22,5mm/85,0mm/65,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 1,3 HU
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Protection type (EN 60529)
Tests/Certification
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
IP 50
CE
smartCOM line termination module.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
Wiring example:
Commissioning:
•
•
•
•
Notes:
•
•
•
Module must be present at the end of every evon smartCOM
line (termination).
Maximum total smartCOM Line length 600m
Maximum distance between 2 participants 100m
•
•
•
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Isolate the system from the mains before beginning commissioning.
Start the installation work with a controller (e.g. iX800) or a converter module S1200 on the left-hand side of the cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into the left terminal of
the module.
Mount the module on the DIN rail; it will click when seated correctly.
Push the module along the rail to the left-hand module in the system.
Ensure that the free pins of the connector snap into place in the socket of
the adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Version 1.0
Module Sys 1200-00
Module dimensions:
evonHOME module type b (refer to technical data sheet module
types) width/height/depth: 22,5mm/85,0mm/65,0mm
Screw base depth 38,5mm
Horizontal pitch [U] = 1,3 HU
Environmental conditions
Operating conditions
Storage conditions
Pollution degree
Protection type (EN 60529)
Tests/Certification
-15..+55°C, 5..90 % rH, non-condensing
-25..+70°C, 5..90 % rH, non-condensing
2
IP 50
CE
Bus converter module for smartCOM lines with RJ45 network
cable connector.
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
Important before commissioning:
•
•
•
Supply every module with power.
Please check whether the GND supply corresponds to the earth zero potential.
Larger loads on the module outputs, together with capacitive and inductive loads, must be switched via relays.
Wiring example:
Commissioning:
•
•
•
•
Notes:
•
•
•
•
•
•
Standard Ethernet cables can be used as connections
Warning: An evon smartCOM line cannot be routed via a home
network (switch router).
Direct connection from S1200 to S1200
Maximum total length smartCOM line 300m
Maximum distance between 2 participants 100m
Application: used to connect modules in different cabinets or
distribution points.
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
•
•
•
Isolate the system from the mains before beginning
commissioning.
Start the installation work with a controller (e.g. iX800) or
a converter module S1200 on the left-hand side of the
cabinet.
The modules can only be mounted from left to right.
Plug the included 5-pole smartCOM line connector into
the left terminal of the module..
Mount the module on the DIN rail; it will click when
seated correctly.
Push the module along the rail to the left-hand module
in the system. Ensure that the free pins of the connector
snap into place in the socket of the adjacent module.
Please check whether the GND supply for the 24 V power supply corresponds to an earth zero potential!
Version 1.4
HC-WSLRW-00
Installation, testing, operational start-up and troubleshooting should
only be performed by an electrician.
Wiring example:
Close the housing by putting
the cover back over the bottom
part. The cover must snap in on
the left and right with a definite
“click”.
Technical specifications
Housing
Colour
Mounting
Protection category
Dimensions
Weight
Ambient temperature
Operating voltage
Current
Data output
Heating rain sensor
Measurement range temperature
Measurement range wind
Measurement range brightnes
Plastic material
White / translucent
On-wall
IP 44
approx. 96 × 77 × 118 (W × H × D, mm)
approx. 160 g
Operation -30…+50°C, Storage -30…+70°C
24 V DC
max. 120 mA, residual ripple 10%
RS485
approx. 1.2 W
-40…+80°C
0…70 m/s
0...99.000 lux
Installation and commissioning
The device is only to be used for its intended purpose. Any improper modification or failure to follow the operating instructions voids any and all warranty and
guarantee claims.
After unpacking the device, check it immediately for possible mechanical damage.
If it has been damaged in transport, inform the supplier immediately.
The device may only be used as a fixed-site installation; that means only when
assembled and after conclusion of all installation and operational start-up tasks
and only in the surroundings designated for it.
Elsner Elektronik is not liable for any changes in norms and standards which may
occur after publication of these operating instructions.
Mounting the sensor
Push the housing from
above into the fastened
mount. The bumps on the
mount must
snap into the rails in the
housing.
When assembling , make sure that the temperature sensor (small PCB
on the bottom of the housing) is not damaged . The cable connection
between the blank and the rain sensor must not be torn or kinked at the
terminal.
Installation position
Choose an installation position in the building where wind, rain and sun
can be measured unhindered by the sensors. The weather station must
not be installed underneath any structural parts from which water can
still drip onto the rain sensor after it has stopped raining or snowing.
The weather station must not be shaded by anything, such as building
structures or trees. At least 60 cm of clearance must be left all round the
weather station. This facilitates correct wind speed measurement without
eddies. The distance concurrently prevents spray (raindrops hitting the
device) or snow (snow penetration) from impairing the measurement.
It also does not allow birds to bite it. Please take note that an extended
awning does not shade the device from sun and wind. Temperature
measurements can also be affected by external influences such as by
warming or cooling of the building structure on which the sensor is
mounted, (sunlight,heating or cold water pipes).
The weather station must be mounted on avertical wall (or a
pole) and in the horizontal transverse direction (horizontally).
When installed on the northern
hemisphere , the weather station
must be oriented to the south .
When installed in the southern
hemisphere , the weather station
must be oriented to the north .
Nord
Süd
Attaching the mount
The sensor comes with a combination wall/pole mount. The mount
comes adhered by adhesive strips to the rear side of the housing. Fasten
the mount vertically onto the wall or pole.
When wall mounting: flat side on wall, crescent-shaped collar upward.
When pole mounting: curved side on pole, collar downward.
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Version 1.0
HC-CAM12-00
evonHOME Bullet-Camera 2 MP FullHD (1920x1080).
Properties:
2 MP FullHD (1920 x 1080), Infrared night vision mode (... 30m),
Automatic switching to night mode, POE, Advanced add capabilities
of the camera software
Supply
Power supply
Nominal consumption
Camera
Image sensor
Min. brightness
Lens
Day/Night operation
Noise reduction
Video
Compression
Bitrate
Dual stream
Image
Max. Resolution
BLC (Black Light Compensation)
Advanced features
Network storage
Alarm
Supported protocols
Compatibility
Environmental conditions
Operation conditions
Protection type (EN60529)
Test/Certification
General
Dimensions
Weight
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
12 Vdc +/-10 % PoE (802.3af)
max. 5 W (max. 7W with IR)
1/2,8“ progressive scan CMOS
0.01 lux @1.2, AGC ON, 0 lux with IR
4mm @F2.0, Angle: 90°
Automatic switching with IR filter
Digital DNR
H.264+ / H.264 / MJPEG
32 Kbps ~ 16 Mbps
Yes
1920 x 1080
Yes
NAS (Confiugration via camera software)
motion detection, sabotage detection (Confiugration via camera software)
TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS,
DDNS, RTCP, PPPoE, NTP, UPnP, SMTP, SNMP,
IGMP, 802.1X, QoS, IPv6, Bonjour
ONVIF, PSIA, CGI
Commissioning:
•
•
•
•
•
The camera is pre-configured for optimum performance with evonHOME.
Any changes in settings done via the camera software or the web interface
could limit the functionality with evonHOME.
After installation, the camera must be supplied with power via POE
(power over Ethernet). This can be done either via POE injector or a POE
connection on the existing switch (802.3af ).
Once the power (POE) has been applied, the camera will require several
minutes before it is completely ready for operation.
The camera is configured with automatic IP address assignement (DCHP),
so it can be found by evonHOME.
-30°C ... +60°C, max.95% rH, non-condensing
IP66
CE
70 x 154,2 x 60,5 mm
500 g
Notes:
•
•
•
Standard user: admin
Password: admin1234
Changes to user data must be carried out in evonHOME and using the
camera’s web interface.
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Version 1.1
HC-DCAM20-00
Properties:
2 MP FullHD (1920 x 1080), Infrared night vision mode (... 30m),
Automatic switching to night mode, POE, Advanced add capabilities
of the camera software
Supply
Power supply
Nominal consumption
Camera
Image sensor
Min. brightness
Lens
Day/Night operation
Noise reduction
Video
Compression
Bitrate
Dual stream
Image
Max. Resolution
BLC (Black Light Compensation)
Advanced features
Network storage
Alarm
Supported protocols
Compatibility
Environmental conditions
Operation conditions
Protection type (EN60529)
Test/Certification
General
Dimensions
Weight
evonHOME Dome-Camera 2 MP FullHD (1920x1080).
ATTENTION ELECTRICAL VOLTAGE:
Disconnect all system components from the mains before commencing work.
The components may ONLY cabled with the mains disconnected.
The cabling may only be carried out by trained expert personnel.
12 Vdc +/-10 % PoE (802.3af)
max. 5 W (max. 7W with IR)
1/2,8“ progressive scan CMOS
0.01 lux @1.2, AGC ON, 0 lux with IR
4mm @F2.0, Angle: 106°
Automatic switching with IR filter
Digital DNR
H.264+ / H.264 / MJPEG
32 Kbps ~ 16 Mbps
Yes
1920 x 1080
Yes
NAS (Confiugration via camera software)
motion detection, sabotage detection (Confiugration via camera software)
TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS,
DDNS, RTCP, PPPoE, NTP, UPnP, SMTP, SNMP,
IGMP, 802.1X, QoS, IPv6, Bonjour
ONVIF, PSIA, CGI
Commissioning:
•
•
•
•
•
The camera is pre-configured for optimum performance with evonHOME.
Any changes in settings done via the camera software or the web interface
could limit the functionality with evonHOME.
After installation, the camera must be supplied with power via POE
(power over Ethernet). This can be done either via POE injector or a POE
connection on the existing switch (802.3af ).
Once the power (POE) has been applied, the camera will require several
minutes before it is completely ready for operation.
The camera is configured with automatic IP address assignement (DCHP),
so it can be found by evonHOME.
-30°C ... +60°C, max.95% rH, non-condensing
IP66
CE
ø 111 x 82 mm
500 g
Notes:
•
•
•
Standard user: admin
Password: admin1234
Changes to user data must be carried out in evonHOME and using the
camera’s web interface.
*Changes and errors excepted. This document does not claim to be exhaustive. The terms and conditions apply to evon GmbH. For more Details please visit our website www.evon-home.com
Version 1.1