Download Banner SB12 Series Emitters/Receivers Pair

SB12 Series Emitter/Receiver Photoelectric
Sensors
Datasheet
The SB12 Emitter/Receiver pair is a cost effective sensor for large volume OEM applications. The unique snap-in mounting
system works with any material with a thickness of 1.5 mm to 3 mm. Simply drill a 12.7 mm (0.5 inch) diameter hole,
insert the cable, and press the sensor into place.
•
•
•
•
•
•
Small 12.7 mm (0.5 inch) tubular E/R pair
Easy-to-mount; no brackets required — simply press sensor into a 12.7
mm (0.5 inch) diameter hole with a panel thickness between 1.5 and 3
mm
Narrow effective beam allows for multiple sensors in close proximity
LED status indicators for Power ON, Output Overload, Signal Received
and Marginal Signal
10–30V dc supply voltage with single NPN or PNP output, depending on
model
Light Operate (LO) or Dark Operate (DO), depending on model
Opposed Mode, 880 nm Infrared
Models
Type
SB12E1
Emitter
Range
Output Type
—
SB12ANR
NPN/LO
SB12RNR
NPN/DO
SB12APR
Receiver
Beam Pattern
SB12
SB12RPR
PNP/DO
6"
100 mm
4"
50 mm
2"
0
PNP/LO
1.5 m
(59 inches)
Opposed Mode
150 mm
0
50 mm
2"
100 mm
4"
150 mm
6"
0
0.4 m
16"
0.8 m
32"
1.2 m
48"
1.6 m
64"
2.0 m
80"
DISTANCE
Standard 2 m (6.5 ft) cable models are listed. QD Models: For 3-Pin 150 mm (6 inch) pigtail with threaded Pico-style M8
connector, add suffix “Q3” to the model number (e.g. SB12E1Q3).
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to
serious injury or death. This device does not include the self-checking redundant circuitry necessary
to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an
energized or de-energized sensor output condition.
Hookup Diagrams
Emitter
1
PNP Receiver
+
10-30V dc
3
–
1
+
10-30V dc
–
3
4
NPN Receiver
Load
3
–
10-30V dc
+
1
4
1 = Brown
3 = Blue
4 = Black
Load
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
SB12 Series Emitter/Receiver Photoelectric Sensors
Specifications
Specifications are subject to change without notice
Output Configuration
One solid state output, NPN (sinking) or PNP
(sourcing), depending on model
Sensing Beam
880 nm invisible infrared beam
Sensing Range
1.5 m (59 inches)
Output Rating
100 mA
OFF-state leakage current: < 10 µA
ON-state saturation voltage: < 0.2V @ 10 mA; <
0.6V @ 100 mA
Supply Voltage
10–30 V dc; less than 15 mA exclusive of load
Supply Protection Circuitry
Protected against reverse polarity and transient
over voltages
Output Protection Circuitry
Protected against output short circuit, continuous
overload and transient over voltages
Delay at Power-up
Less than 1 second
Output Response Time
2.5 ms ON, 1.75 ms OFF
Indicators
Green Power LED (emitter and receiver):
• ON indicates power on;
• Flashing indicates output short circuited
(receiver only)
Amber Output LED (receiver only):
• ON indicates light sensed;
• Flashing indicates marginal excess gain
(1.0 to 1.5x excess gain)
Repeatability
350 µs
Switching Frequency
235 Hz
Environmental Rating
IP65
Operating Conditions
Temperature: –20º to +50º C (–4º to 122º F)
Construction
Housing: ABS
Lens: Polycarbonate; epoxy encapsulant
PVC-jacketed cable
Certifications
Connections
2 m (6.5 ft) cable or 150 mm (6 inch) pigtail with
M8 threaded connection
Dimensions
31 mm
[1.2"]
27.5 mm [1.08"]
18 mm [0.71"]
Ø15.8 mm
[0.62"]
12.5 mm
[0.49"]
11.5 mm [0.45"]
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
SB12 Series Emitter/Receiver Photoelectric Sensors
Accessories
3-Pin Threaded M8/Pico-Style Cordsets
Model
Length
Style
PKG3M-2
2 m (6.56 ft)
Straight
PKG3M-5
5 m (16.40 ft)
PKG3M-7
7 m (22.97 ft)
PKG3M-9
9 m (29.53 ft)
PKG3M-10
10 m (32.81 ft)
PKW3M-2
2 m (6.56 ft)
PKW3M-5
5 m (16.40 ft)
PKW3M-9
9 m (29.53 ft)
Dimensions
Pinout
4
35 Typ.
1
3
ø 9.5
M8 x 1
1 = Brown
3 = Blue
4 = Black
Right-Angle
28 Typ.
20 Typ.
M8 x 1
ø 9.5
Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following
the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture
which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty
does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR
IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR
TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO
EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR
ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR
SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE
PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY,
NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any
obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]