Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
For intelligent installation in partition wall systems: Gira ITS 30 Flexible multi-talent Flexible partition wall systems play an increasingly important role in the design of modern room concepts in building construction. Here architects make increasing use of transparent solutions. However, glass partition walls caused problems for the electrical installation up until now. Gira has accepted this challenge and will present an installation system with the greatest possible functionality and flexibility at the Light + Building, which also meets the demanding design requirements in high-quality building interior decoration. With modern partition wall systems, room concepts can be realised quickly and can then still be changed later. Of course, this demands an enormous degree of flexibility from electrical engineering. Especially here the Gira ITS 30 developed for intelligent installation in partition wall systems sets new standards. As a "before-wall installation system", it is especially intended for use on glass partition-wall elements: Special installation housings are mounted on a base rail between the door reveal and partition wall. These housings hold devices and functions of the electrical installation and Instabus technology. Now socket outlets, switches, orientation lights, automatic control switches, blind control buttons and push button sensors can be positioned before the glass wall and near the room door. The base rail is inserted in a joint with a width of just 30 mm between the door and the partition wall. The slim profile eliminates the need for the wide panel required here in the past and also offers considerable cost advantages compared to conventional installations. With glass walls the advantage of Gira ITS 30 is apparent: Due to the narrow joint, the amount of glass in the partition walls increased, allowing considerably more transparency and brightness in the room . Of course, the system can also be integrated in solid partition walls. The base rail serves as an installation duct for power and control cables that can be routed in from the ceiling or floor. Following installation, the rail is closed with an aluminium cover. The housings mounted on the base rail including the functions integrated in – 2 – them join via special cover frames to form a uniform design range. All modules from five Gira switch ranges with over 180 functions and the Gira SmartSensor room control device can be integrated in it. As a result, the well thought-out installation system offers a unique depth of functions for the entire range of electrical installations in modern buildings. But it was not developed by Gira alone, but instead in co-operation with the manufacturer Mabeg, the specialist for management and orientation systems. And it is therefore also possible to integrate door and name plates from the Mabeg product range COM.form in the Gira ITS 30. The Gira ITS 30 installation system available from autumn 2004 meets the requirement for the greatest possible flexibility for room planning and use, especially in building and investment construction. For the module design enables changes in room use to be realised quickly and at low cost: In next to no time the various individual functions can be installed in the profile, replaced or interconnected, e.g. when several rooms are combined to form a conference room and many simple function units are to be combined in a SmartSensor . The Gira SmartSensor is a control and operating unit for all Instabus functions in a room which is already available on the market. It combines many otherwise individual functions usually controlled with push button sensors in one device. Its operation is simple, convenient and intuitive via a LC display, an operating button for turning and pressing or via rockers on the device. The rotary/push button is used to navigate within the operating structure shown on the display. The display visualises the menu items required for navigation. By turning the knob the user can scroll through the menu, and by pressing it an item in the menu can be selected. The four additional rockers on the side of the device are used for a direct (and therefore quick) operation of the most important functions. Picture captions: GIRA_ITS30_SmartSensor Gira has developed the ITS 30 for intelligent installation in partition wall systems. The Gira SmartSensor, the control and operating unit for all – 3 – Instabus functions in a room which has already been introduced on the market, can be integrated in it. Photo: GIRA GIRA_ITS30_SCHUKO With the Gira ITS 30, special installation housings are mounted on a narrow base rail. These then hold the devices and functions of the electrical installation and bus technology. Now socket outlets, switches, orientation lights, automatic control switches, blind control buttons and push button sensors can be positioned before the glass wall. Photo: GIRA GIRA_ITS30_Türschild The unique form of installation was developed in co-operation with the manufacturer Mabeg. It is therefore also possible to integrate door and name plates from the Mabeg product range COM.form in the Gira ITS 30. Photo: GIRA