Download safe work instructions for

SAFE WORK INSTRUCTIONS FOR
Ultrasonic Cleaner
Campus:
Clayton, VIC
Faculty:
Engineering
Department: Materials Engineering
Building:
37
Room No:
Investigator
1.





Electrical hazards associated with the use 240 VAC electrical appliances.
Ultrasonic energy can cause damage to joint tissues if fingers or any other part of a body is
immersed in the cleaning fluid of an operating ultrasonic cleaner.
Prolonged exposure to high frequency sound emitted from an operating ultrasonic cleaner unit
may lead to hearing impairment.
Organic solvent is flammable, harmful and may be reactive hazard if mix with other chemicals.
Locate first-aid box, safety shower, eye wash, emergency telephone, emergency exits and fire
extinguisher.
Locate MSDS and risk assessment in the folder behind the lab door.
Safety glasses, closed-toe shoes, protective gloves, lab coat, mist mask.
Loose and long hair should be tied back away from the face.
The environment where the task is to be undertaken:




6.
Authorisation from academic-in-charge, Dr Chris Hutchinson is required to undertake work in the
metallography laboratory
Potential user should complete the risk control worksheet and assessment
Potential user should be trained by a qualified or licensed user (see Dr Chris Hutchinson)
Personal protective equipment (PPE) to be used:


5.
Signature
Preparation for work:

4.
Phone #
Hazards associated with equipment/process:


3.
Assessment Date:
Authorisation

2.
186
The ultrasonic cleaner unit should be mounted on a level surface, free from extreme temperatures,
strong vibrations and corrosive environment to protect the equipment from damage.
Working bench and floor should be dry and clean to avoid electric shock, slip and contamination.
No naked flame, heat or ignition source in the vicinity
No eating, drinking or smoking
Step-by-step working procedures
a) Wear PPE as mentioned above.
b) Visually inspect condition of the ultrasonic cleaner unit and the electrical connection is
satisfactory.
c) If necessary, clean and fill the tank with water to the appropriate level. Do not over fill with water
that causes water to spill over the top of the tank. Too low a water level will result in poor
cleaning efficiency and may cause transducers damage.
d) Ensure that the external surface and electrical connection are thoroughly dry before plugging the
cleaner to the mains supply.
e) Suspend the stainless steel mesh tray inside the water-filled tank. Items to be cleaned should not
be placed directly on the tank bottom; otherwise the transducers could be damaged because of
ultrasonic energy reflecting directly back to the transducers
f) Fill a small beaker with the cleaning solution to the level sufficient to cover the item to be
cleaned.
g) Gently lower the beaker onto the mesh tray suspended inside the water-filled tank. Care should be
taken not to allow water to overflow the top of the tank. The beaker should be stable when seated
on the mesh tray. Otherwise add more cleaning solution for more weight.
h) Switch on the unit to degas both the water and the cleaning solution. Cover the lid to reduce noise
and aerosols escaping. Degassing will provide optimal cleaning.
i) After 5-10 mins of degassing, switch off the unit and gently put the item to be cleaned (using a
pair of forceps or tongs) in the beaker of cleaning solution. Switch on the unit and cover the lid.
j) Monitor the cleaning process regularly; if necessary, use the timer switch. Switch off the unit to
inspect the item.
7.
Clean-up procedures




If the water in tank is contaminated, unplug the unit from the mains before draining the
contaminated water.
Thoroughly rinse the tank with fresh water. If necessary, clean inside of tank with sponge and
mild detergent.
Fill the tank with clean water.
Dry all external surfaces of the unit with particular attention on the electrical connection and
socket.
8.
Waste disposal procedures
 Dispose of any waste organic solvent in the designated receptacle for eventual disposal
through Chemsal.
 Dispose of other cleaning solutions as per respective MSDS guidelines.
9.
Emergency procedures






10.
After-hours access procedures



11.
In case of emergency alarm or power outage, leave the lab in an orderly manner.
Use the emergency red phone or dial ‘333’ for any emergency.
For minor injury requiring first aid treatment, use the first-aid cabinet or contact the nearest firstaider.
In case of minor spills, wear appropriate PPE and wipe spills with paper towels.
Report any major spills; a general chemical spill treatment kit (in Room 179) may be used. Refer
to MSDS for further procedures.
If contact with acetone or ethanol, rinse skin or eyes with fresh running water.
After-hours access is restricted; contact Dr Chris Hutchinson for after-hours authorization.
Register your details in the after-hours log book if the metallography lab is to be used after
normal working hours.
Only trained and licensed user of the equipment is allowed to enter the log book.
Associated Documents


Risk assessment for ultrasonic cleaner
MSDS for ethanol
Prepared by:
Date:
……………………
Signed :
…………………….