DIY Factory
... comparing that is all we have and even though a simple single numeral would be nice it often takes more information to tell us what is going on or to compare one unit to another. I'm sure we are all familiar with V = I R but so many do forget when delving into audio. Some thought may be given to Pow ...
... comparing that is all we have and even though a simple single numeral would be nice it often takes more information to tell us what is going on or to compare one unit to another. I'm sure we are all familiar with V = I R but so many do forget when delving into audio. Some thought may be given to Pow ...
Large-panel digital display
... The control unit is supplied with two cables, each with a 4-pin plug. The control unit supply must be 24 V AC or DC. A built-in transformer ensures that the measuring circuit is isolated from the current supply. In order to retain the isolation, a supply voltage which is similarly isolated from the ...
... The control unit is supplied with two cables, each with a 4-pin plug. The control unit supply must be 24 V AC or DC. A built-in transformer ensures that the measuring circuit is isolated from the current supply. In order to retain the isolation, a supply voltage which is similarly isolated from the ...
Selecting Your Sigma II Indexer System
... Select the required power components (servomotor, power and feedback connectors or pre-wired cables, amplifier, regenerative packs, etc.) from the following catalog pages. Use this table or the Yaskawa publications referenced below to determine which catalog section describes the best servomotor for ...
... Select the required power components (servomotor, power and feedback connectors or pre-wired cables, amplifier, regenerative packs, etc.) from the following catalog pages. Use this table or the Yaskawa publications referenced below to determine which catalog section describes the best servomotor for ...
INPUT/OUTPUT UNIT WITH ISOLATOR - Det
... The XP95 Input/Output Unit with Isolator provides two voltage-free, single pole, change-over relay outputs, a single monitored switch input and an unmonitored, non-polarised opto-coupled input. FEATURES The Input/Output Unit supervises one or more normally-open switches connected to a single pair of ...
... The XP95 Input/Output Unit with Isolator provides two voltage-free, single pole, change-over relay outputs, a single monitored switch input and an unmonitored, non-polarised opto-coupled input. FEATURES The Input/Output Unit supervises one or more normally-open switches connected to a single pair of ...
6 – 10 Watt Stereo Audio Amplifier (Code 3143)
... 6 – 10 Watt Stereo Audio Amplifier (Code 3143) ...
... 6 – 10 Watt Stereo Audio Amplifier (Code 3143) ...
XUPS-600-1000
... TSi’s ongoing product improvement process makes specifications subject to change. Other companies product names herein are for identification purposes only, and may be trademarks of their respective companies. ...
... TSi’s ongoing product improvement process makes specifications subject to change. Other companies product names herein are for identification purposes only, and may be trademarks of their respective companies. ...
Rupert Neve Portico 5032
... Therefore the holes should not be covered or blocked. Portico™ modules may be stacked horizontally on a desktop or mounted vertically in a rack without heat problems. The anti-slip feet may be removed while used in a rack, but should be retained for desktop use. To avoid overheating, Portico™ module ...
... Therefore the holes should not be covered or blocked. Portico™ modules may be stacked horizontally on a desktop or mounted vertically in a rack without heat problems. The anti-slip feet may be removed while used in a rack, but should be retained for desktop use. To avoid overheating, Portico™ module ...
CONSUMMATE PHONO STAGE - Jeff Rowland Design Group
... If the output impedance of the Phono Stage is set for 300 ohms and the input impedance of your Consummate (or other line) preamplifier is also set for 300 ohms, then the interface between the two components will be optimized or "impedance matched." This condition will yield the most accurate perform ...
... If the output impedance of the Phono Stage is set for 300 ohms and the input impedance of your Consummate (or other line) preamplifier is also set for 300 ohms, then the interface between the two components will be optimized or "impedance matched." This condition will yield the most accurate perform ...
Maxstar® 150 STH
... Stick electrode holder with 13-ft. (4 m) cable and 25-mm Dinse-style connector Work clamp with 10-ft. (3 m) cable and 25-mm Dinse-style connector Flow gauge regulator with gas hose AK2C accessory kit with short back cap, nozzles, collets, collet bodies, and 2% ceriated tungsten electrodes (.040, 1/1 ...
... Stick electrode holder with 13-ft. (4 m) cable and 25-mm Dinse-style connector Work clamp with 10-ft. (3 m) cable and 25-mm Dinse-style connector Flow gauge regulator with gas hose AK2C accessory kit with short back cap, nozzles, collets, collet bodies, and 2% ceriated tungsten electrodes (.040, 1/1 ...
MixPre-D - User Guide and Technical Information
... Devices outputting line-level signal (outputs from other mixers, for example) ...
... Devices outputting line-level signal (outputs from other mixers, for example) ...
CNS 100 / 150 / 200 / 250
... N.B. - The convector heater must not be mounted immediately below a wall socket, or any shelves, (it could melt electrical plug socket and cause a fire.) - When the unit is first turned on it might give off a smell as the element is burning off factory coating and dust. This is no cause for alarm, E ...
... N.B. - The convector heater must not be mounted immediately below a wall socket, or any shelves, (it could melt electrical plug socket and cause a fire.) - When the unit is first turned on it might give off a smell as the element is burning off factory coating and dust. This is no cause for alarm, E ...
Phone connector (audio)
In electronics, a phone connector, also known as phone jack, audio jack or jack plug, is a common family of connector typically used for analog signals, primarily audio. It is cylindrical in shape, typically with two, three or four contacts. Three-contact versions are known as TRS connectors, where T stands for ""tip"", R stands for ""ring"" and S stands for ""sleeve"". Similarly, two- and four-contact versions are called TS and TRRS connectors respectively.The phone connector was invented for use in telephone switchboards in the 19th century and is still widely used. In its original configuration, the outside diameter of the ""sleeve"" conductor is 1⁄4 inch (exactly 6.35 mm). The ""mini"" connector has a diameter of 3.5 mm (approx. 1⁄8 inch) and the ""sub-mini"" connector has a diameter of 2.5 mm (approx. 3⁄32 inch).