* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Series One Programmable Controllers Series One/One Plus User`s
Phone connector (audio) wikipedia , lookup
Buck converter wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Current source wikipedia , lookup
Control system wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Analog-to-digital converter wikipedia , lookup
Flip-flop (electronics) wikipedia , lookup
Two-port network wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Flexible electronics wikipedia , lookup
Schmitt trigger wikipedia , lookup
6-14 I/O Specifications and Wiring GEK-90842 24 V ac/dc Source Input (16 Circuits) With Removable Terminal Board IC610MDLllZ This module provides 16 input circuits, with LED indicators, each designed to receive a single discrete (ON/OFF) signal fkom user supplied devices. Typical input devices include pushbuttons, limit switches, selector switches and relay contacts. These input circuits can interface to either 24 V ac signals or 24 V dc source-type signals, thereby allowing the module to interface to input devices that provide their own voltage. In addition, the module can be connected as a sink input. When using the sink configuration, the user must supply the source of power for the input devices, as when used in the source input configuration. Following are specifications for each of the 16 circuits. Input VoMage (source or Sink) Input current ON Level OFF Level OFF to ON Response ON to OFF Response Circuit Indicator Intemal Power Consumption ACIWUT 14 to 30 v ac, 50-60 Hz 12mA@24Vac 14 to 30 v ac oto3vac 5 to 30 Ins 5 to 30 ms Logic Side Units of Load wei%lt DCKNPUT 20-28 V dc 12mA@24& 14 to 30 v tic oto3vdc 5 to 25 ms 5to25ms Logic Side 9 V dc, 130 mA (maximum) Typical, 25 mA + 4.5 mA for each ON circuit 13 6 oz (170 g) a40800 User devices are connected to screw terminals on the removable connector mounted on the faceplate of this module. Each SCRW terminal will accept up to one No. 12 AWG wire or two No. 14 AWG wires. The On/OFF state of each circuit is indicated by an LED located in the logic side of each circuit. The 16 circuits are divided into 2 groups of 8, each with its own common. The two commons, CA and CB a~ isolated fkom each other internally. Each input can accept either an AC input or a DC input. I6 CIRCUITSON I6 NUMBER 12 - OF CIRCUITS ON *- IO CiRC'JiTS ON 7 CIRCUITSON 5 CIRCbiTSOh 49 I I IO’C ZO’C AMKENT I 30% 1 4O'C 1 SOY ! 6O'C TEMPERATURE ('Cl F’iiiigure 6-14. I/O Points vs Temperature chart I/O Specifications and Wiring 6-15 GEK-90842 a40801 USER WIRING I USER WIRING MODULE r 1 --b Fb, 14 - 30VAC I NPICAL REFERENCES 010 011 012 013 3 014 015 5 016 017 0 111 110 2 113 112 4 115 114 6 117 116 CA 0 0 2 4 6 7 CB 3 5 7 WIRING DIAGRAM INPUT (O-7) _~__” 8 t 1 -’ ’ I I A@ t’ DC OR $ ; J. 'Y I ::.:; . -r’8 .rdr-r- AC COMMOC OPTICAL (CA, CB) SAMPLE INPUT CIRCUIT FIGURE 6 15 WIRING FOR 16 CIRCUIT 24 VAC/DC LOAD INPUTS SOURCE Figure 6-15. Wiring for 16 Circuit 24 V ac/dc Source Load Inputs