• Study Resource
  • Explore Categories
    • Arts & Humanities
    • Business
    • Engineering & Technology
    • Foreign Language
    • History
    • Math
    • Science
    • Social Science

    Top subcategories

    • Advanced Math
    • Algebra
    • Basic Math
    • Calculus
    • Geometry
    • Linear Algebra
    • Pre-Algebra
    • Pre-Calculus
    • Statistics And Probability
    • Trigonometry
    • other →

    Top subcategories

    • Astronomy
    • Astrophysics
    • Biology
    • Chemistry
    • Earth Science
    • Environmental Science
    • Health Science
    • Physics
    • other →

    Top subcategories

    • Anthropology
    • Law
    • Political Science
    • Psychology
    • Sociology
    • other →

    Top subcategories

    • Accounting
    • Economics
    • Finance
    • Management
    • other →

    Top subcategories

    • Aerospace Engineering
    • Bioengineering
    • Chemical Engineering
    • Civil Engineering
    • Computer Science
    • Electrical Engineering
    • Industrial Engineering
    • Mechanical Engineering
    • Web Design
    • other →

    Top subcategories

    • Architecture
    • Communications
    • English
    • Gender Studies
    • Music
    • Performing Arts
    • Philosophy
    • Religious Studies
    • Writing
    • other →

    Top subcategories

    • Ancient History
    • European History
    • US History
    • World History
    • other →

    Top subcategories

    • Croatian
    • Czech
    • Finnish
    • Greek
    • Hindi
    • Japanese
    • Korean
    • Persian
    • Swedish
    • Turkish
    • other →
 
Profile Documents Logout
Upload
2.6.4 Interfacing Outputs Word Document | GCE AS/A
2.6.4 Interfacing Outputs Word Document | GCE AS/A

Lab #3 Report: KVL and KCL Adam Stokes Partner: Davis Roberts 9
Lab #3 Report: KVL and KCL Adam Stokes Partner: Davis Roberts 9

... The voltage and current in a circuit can be calculated by writing out a system of KVL and KCL equations and then solving for the missing variables. The values can also be found by using an ammeter and voltmeter and measuring in parallel (for voltage) and series (for current). For circuit 3, multisim ...
lab 14a directions
lab 14a directions

03_5_FPLD_methodology
03_5_FPLD_methodology

Slide 1 - Wake Forest University
Slide 1 - Wake Forest University

Ground isolation amplifier
Ground isolation amplifier

... third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's rig ...
150LECTURE14CHAPTER13 RCL CIRCUITS Lecture Notes Page
150LECTURE14CHAPTER13 RCL CIRCUITS Lecture Notes Page

Series and Parallel Circuits Computer Lab
Series and Parallel Circuits Computer Lab

Lecture 1: CS/ECE 3810 Introduction • Today’s topics: Why computer organization is important
Lecture 1: CS/ECE 3810 Introduction • Today’s topics: Why computer organization is important

A circuit must contain a source of potential difference, and a path for
A circuit must contain a source of potential difference, and a path for

... the flow of charge. It will probably also contain a load or resistance (a user of energy). ...
P-type Transistor
P-type Transistor

Electricity and Electronics
Electricity and Electronics

output will oscillate between values of approximately +10 volts and
output will oscillate between values of approximately +10 volts and

... We will discuss circuit (b) shown below in class. Please be sure that you understand why the op amp output will oscillate between values of approximately +10 volts and –10 volts. Note that the “three zeros” of ideal op amp operation (with feedback) are not valid for this circuit! ...
06 lecture #6
06 lecture #6

Where Can You Go after ELEC 312 ?
Where Can You Go after ELEC 312 ?

Chapter 20 Electricity
Chapter 20 Electricity

... 6. What type of current is used in a battery? A. parallel current C. direct current B. alternating current D. potential current 7. The type of current in your home is mostly A. direct current. C. series current. B. alternating current. D. produced by batteries. 8. Which of the following materials al ...
FET Current Mirrors
FET Current Mirrors

Document
Document

Parallel circuits
Parallel circuits

MAN30x0A, 60x0, 80x0
MAN30x0A, 60x0, 80x0

Test - Electro Tech Online
Test - Electro Tech Online

Table of Formulas and Constants * Physics 102
Table of Formulas and Constants * Physics 102

... For moving a magnet in or out of a coil or turning a field on or off ...
Intro & Circuit Review I - University of Delaware Dept. of Physics
Intro & Circuit Review I - University of Delaware Dept. of Physics

... • Do not touch circuit with bare hands when the power is on • Make sure the grounding is good • Do not short voltage sources or open current ...
Symbols for Circuits
Symbols for Circuits

... (in your mind, but I always draw it again) the parallel section with a single resistor having a resistance value equal to the equivalent resistance of the parallel section. • Use the Ohm's law equation (V = I • R) often and appropriately. Most answers will be determined using this equation. When usi ...
Residential Wiring
Residential Wiring

< 1 ... 274 275 276 277 278 279 280 281 282 ... 304 >

Integrated circuit



An integrated circuit or monolithic integrated circuit (also referred to as an IC, a chip, or a microchip) is a set of electronic circuits on one small plate (""chip"") of semiconductor material, normally silicon. This can be made much smaller than a discrete circuit made from independent electronic components. ICs can be made very compact, having up to several billion transistors and other electronic components in an area the size of a fingernail. The width of each conducting line in a circuit can be made smaller and smaller as the technology advances; in 2008 it dropped below 100 nanometers, and has now been reduced to tens of nanometers.ICs were made possible by experimental discoveries showing that semiconductor devices could perform the functions of vacuum tubes and by mid-20th-century technology advancements in semiconductor device fabrication. The integration of large numbers of tiny transistors into a small chip was an enormous improvement over the manual assembly of circuits using discrete electronic components. The integrated circuit's mass production capability, reliability and building-block approach to circuit design ensured the rapid adoption of standardized integrated circuits in place of designs using discrete transistors.ICs have two main advantages over discrete circuits: cost and performance. Cost is low because the chips, with all their components, are printed as a unit by photolithography rather than being constructed one transistor at a time. Furthermore, packaged ICs use much less material than discrete circuits. Performance is high because the IC's components switch quickly and consume little power (compared to their discrete counterparts) as a result of the small size and close proximity of the components. As of 2012, typical chip areas range from a few square millimeters to around 450 mm2, with up to 9 million transistors per mm2.Integrated circuits are used in virtually all electronic equipment today and have revolutionized the world of electronics. Computers, mobile phones, and other digital home appliances are now inextricable parts of the structure of modern societies, made possible by the low cost of integrated circuits.
  • studyres.com © 2025
  • DMCA
  • Privacy
  • Terms
  • Report