IOSR Journal of VLSI and Signal Processing (IOSR-JVSP)
... sensor networks. The amplifier provides a forward gain (S 21) of ˃ 16 db with a noise figure of S 11 ˂ 2db. While drawing of 10 mw from 1.8v Supply by using inductive coupled degenerated LNA. General Terms: LNA, Noise figure, gain, linearity. Keywords:RF CMOS, VLSI Design, Wireless Communications ...
... sensor networks. The amplifier provides a forward gain (S 21) of ˃ 16 db with a noise figure of S 11 ˂ 2db. While drawing of 10 mw from 1.8v Supply by using inductive coupled degenerated LNA. General Terms: LNA, Noise figure, gain, linearity. Keywords:RF CMOS, VLSI Design, Wireless Communications ...
SPECIFICATION FOR 132kV STATION CLASS SURGE
... manufacturing comparable equipment, in rated voltage and capacity, to the equipment offered under the contract. If the offered equipment is manufactured under license, the service experience of equipment manufactured by the parent company shall not be counted as service experience of the licensee eq ...
... manufacturing comparable equipment, in rated voltage and capacity, to the equipment offered under the contract. If the offered equipment is manufactured under license, the service experience of equipment manufactured by the parent company shall not be counted as service experience of the licensee eq ...
ME 401 (Summer 2012)
... Another home-built can be found at http://www.instructables.com/id/30-kVA-InductionHeater/?ALLSTEPS, constructed by “bwang”. Hazards While induction furnaces have many advantages, as outlined above, they retain all the dangers of working with molten metal and require careful use by the operator. In ...
... Another home-built can be found at http://www.instructables.com/id/30-kVA-InductionHeater/?ALLSTEPS, constructed by “bwang”. Hazards While induction furnaces have many advantages, as outlined above, they retain all the dangers of working with molten metal and require careful use by the operator. In ...
Inside iCoupler® Technology: Polyimide Insulation Layer By
... free of voids and do not suffer from corona discharge, iCoupler devices also exhibit good aging behavior and work well under continuous ac voltages and dc voltages. Besides good high voltage performance, polyimide has excellent ESD performance, capable of handling EOS and ESD events exceeding 15 kV. ...
... free of voids and do not suffer from corona discharge, iCoupler devices also exhibit good aging behavior and work well under continuous ac voltages and dc voltages. Besides good high voltage performance, polyimide has excellent ESD performance, capable of handling EOS and ESD events exceeding 15 kV. ...
Battery Circuit Architecture
... If single-ended measurements are made on the voltage across the sense resistor, it is critical that the VSS of the measuring device be connected to the sense resistor with much care. In the singleended system, the measurement system ground provides one of the inputs for the measurement. The value th ...
... If single-ended measurements are made on the voltage across the sense resistor, it is critical that the VSS of the measuring device be connected to the sense resistor with much care. In the singleended system, the measurement system ground provides one of the inputs for the measurement. The value th ...
Analysis of a floating vs. grounded output
... flow between those two points. These variations in potential cause what are called “ground loops”throughout a system. As shown in Figure 5, the difference in potential between the chassis ground on the power source and the chassis ground on the device under test has caused a ground loop. The effects ...
... flow between those two points. These variations in potential cause what are called “ground loops”throughout a system. As shown in Figure 5, the difference in potential between the chassis ground on the power source and the chassis ground on the device under test has caused a ground loop. The effects ...
Document
... system and other Crestron lighting dimmers to support 120-, 230-, and 277-volt loads up to 16 amps. It allows any output channel of a compatible dimmer to dim a fully loaded circuit of incandescent, magnetic low-voltage, 2-wire dimmable fluorescent, or neon/cold cathode lighting. It is also compatib ...
... system and other Crestron lighting dimmers to support 120-, 230-, and 277-volt loads up to 16 amps. It allows any output channel of a compatible dimmer to dim a fully loaded circuit of incandescent, magnetic low-voltage, 2-wire dimmable fluorescent, or neon/cold cathode lighting. It is also compatib ...
High Voltage Pulse Modulators Tutorial
... are difficult to meet. The diameter of the hollow outer conductor of the (coaxial) cable has to large as compared to the diameter of the inner conductor for the required characteristic impedance and even if we were to have such a cable, we still have the problem of high voltage rating of dc supply. ...
... are difficult to meet. The diameter of the hollow outer conductor of the (coaxial) cable has to large as compared to the diameter of the inner conductor for the required characteristic impedance and even if we were to have such a cable, we still have the problem of high voltage rating of dc supply. ...
Electromagnetic compatibility
Electromagnetic compatibility (EMC) is the branch of electrical sciences which studies the unintentional generation, propagation and reception of electromagnetic energy with reference to the unwanted effects (electromagnetic interference, or EMI) that such energy may induce. The goal of EMC is the correct operation, in the same electromagnetic environment, of different equipment which use electromagnetic phenomena, and the avoidance of any interference effects.In order to achieve this, EMC pursues two different kinds of issues. Emission issues are related to the unwanted generation of electromagnetic energy by some source, and to the countermeasures which should be taken in order to reduce such generation and to avoid the escape of any remaining energies into the external environment. Susceptibility or immunity issues, in contrast, refer to the correct operation of electrical equipment, referred to as the victim, in the presence of unplanned electromagnetic disturbances.Interference mitigation and hence electromagnetic compatibility is achieved by addressing both emission and susceptibility issues, i.e., quieting the sources of interference and hardening the potential victims. The coupling path between source and victim may also be separately addressed to increase its attenuation.