Document
... •IL = V / XL = 120 / 113 = 1.06 A •ii) XL = 2πfL = 2π x 200 x 0.6 = 753 Ω •IL = V / XL = 120 / 753 = 0.159 A ...
... •IL = V / XL = 120 / 113 = 1.06 A •ii) XL = 2πfL = 2π x 200 x 0.6 = 753 Ω •IL = V / XL = 120 / 753 = 0.159 A ...
BDTIC www.BDTIC.com/infineon Automotive Power TLE8366
... 600 mV. The wide input voltage range from 4.75 to 45 V makes the TLE8366 suitable for a wide variety of applications. The device is designed to be used under harsh automotive environment. The switching frequency of nominal 370 kHz allows the use of small and cost-effective inductors and capacitors, ...
... 600 mV. The wide input voltage range from 4.75 to 45 V makes the TLE8366 suitable for a wide variety of applications. The device is designed to be used under harsh automotive environment. The switching frequency of nominal 370 kHz allows the use of small and cost-effective inductors and capacitors, ...
6-Bit Successive Approximation ADC Datasheet
... The acronym SAR stands for “successive approximation register." In this case, the register holding the result of the conversion is the PSoC block’s CR0 register. The basic operating principle is the formation of a series of approximations by scaling the reference voltage, RefHigh, and subtracting it ...
... The acronym SAR stands for “successive approximation register." In this case, the register holding the result of the conversion is the PSoC block’s CR0 register. The basic operating principle is the formation of a series of approximations by scaling the reference voltage, RefHigh, and subtracting it ...
GaN Broadband Power Amplifier
... offers high power over a multi-octave bandwidth. This amplifier operates with a base plate temperature of 85C with no degradation in the MTBF for the GaN devices inside. It is packaged in a modular housing that is approximately 8.0" by 8.0" by 1.5". This amplifier has a typical P3dB of 200 watts at ...
... offers high power over a multi-octave bandwidth. This amplifier operates with a base plate temperature of 85C with no degradation in the MTBF for the GaN devices inside. It is packaged in a modular housing that is approximately 8.0" by 8.0" by 1.5". This amplifier has a typical P3dB of 200 watts at ...
DEH-40700 ASPMETER Panelboard Monitoring System Installation
... FCC PART 15 INFORMATION NOTE: This equipment has been tested by the manufacturer and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is opera ...
... FCC PART 15 INFORMATION NOTE: This equipment has been tested by the manufacturer and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is opera ...
1N4148 pdf
... This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Changes will be communicated according to the Customer Product/Process Change ...
... This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Changes will be communicated according to the Customer Product/Process Change ...
Bergamo - Indico
... - 8-bit precision - Before Tuning threshold spread is about 30 mV which is < 1 fC - After Tuning threshold spread is about 1mV which is the resolution of the offset adjust ...
... - 8-bit precision - Before Tuning threshold spread is about 30 mV which is < 1 fC - After Tuning threshold spread is about 1mV which is the resolution of the offset adjust ...
Review of Circuits as LTI Systems
... where y ′ and y ′′ are the first and second derivatives of signal y(t). Given a known input x(t), we would like to integrate this differential equation to find an expression of y(t) that is only in terms of t. Then we can see how to adjust our design parameters so that y(t) has a desirable shape (e. ...
... where y ′ and y ′′ are the first and second derivatives of signal y(t). Given a known input x(t), we would like to integrate this differential equation to find an expression of y(t) that is only in terms of t. Then we can see how to adjust our design parameters so that y(t) has a desirable shape (e. ...
Additional Gates and Circuits
... More Complex Gates (continued) Example: AOI - AND-OR-Invert consists of a single gate with AND functions driving an OR function which is inverted. Example: 2-2-1 AO has two 2-input ANDS driving an OR with one additional OR input These gate types are used because: • the number of transistors n ...
... More Complex Gates (continued) Example: AOI - AND-OR-Invert consists of a single gate with AND functions driving an OR function which is inverted. Example: 2-2-1 AO has two 2-input ANDS driving an OR with one additional OR input These gate types are used because: • the number of transistors n ...
Technical Article
... AS5132 can implement static pre-commutation by programming its integrated OTP memory block. It is possible to set a shift of 0°, 2°, 4°, 7°, 8°, 10° or 12° (mechanical angle). Once programmed, the offset cannot be changed. In the event of a change of direction, static pre-commutation is always enabl ...
... AS5132 can implement static pre-commutation by programming its integrated OTP memory block. It is possible to set a shift of 0°, 2°, 4°, 7°, 8°, 10° or 12° (mechanical angle). Once programmed, the offset cannot be changed. In the event of a change of direction, static pre-commutation is always enabl ...
What is a Transient Voltage Suppressor Diode
... Suppressors limit voltage spikes to tolerable levels by either clamping or crowbar action. A suppressor that clamps, begins conducting when its threshold voltage is exceeded, then restores to a non-conducting state when the voltage drops below the threshold. Voltage spikes are clipped off to safe le ...
... Suppressors limit voltage spikes to tolerable levels by either clamping or crowbar action. A suppressor that clamps, begins conducting when its threshold voltage is exceeded, then restores to a non-conducting state when the voltage drops below the threshold. Voltage spikes are clipped off to safe le ...
EE2010 - Final Term Exam
... (a) Find the average power Pg and the reactive power Qg and the apparent power S delivered by the voltage source, (b) Find the average power PL and the reactive power QL absorbed by the load. (c) Find the power factor of the load, (d) Determine the value of the capacitor that would correct the power ...
... (a) Find the average power Pg and the reactive power Qg and the apparent power S delivered by the voltage source, (b) Find the average power PL and the reactive power QL absorbed by the load. (c) Find the power factor of the load, (d) Determine the value of the capacitor that would correct the power ...
Fluke 1750 Three-Phase Power Recorder
... control multiple instruments from a distance easily, without the need for a laptop computer (laptops can also be used when desired). ...
... control multiple instruments from a distance easily, without the need for a laptop computer (laptops can also be used when desired). ...
Experiment 1: Measurement and Calculations of Basic Electrical
... dissipate a larger power without overheating. Most of the resistors used in our lab experiments will be ½ W or ¼ W resistors. c. Typical standard resistor values are 1.0, 1.2, 1.5, 1.8, 2.2, 2.7, 3.3, 3.9, 4.7, 5.6, 6.8, 7.5, 8.2, and 9.1 multiplied by a power of 10. Meters are used to make measurem ...
... dissipate a larger power without overheating. Most of the resistors used in our lab experiments will be ½ W or ¼ W resistors. c. Typical standard resistor values are 1.0, 1.2, 1.5, 1.8, 2.2, 2.7, 3.3, 3.9, 4.7, 5.6, 6.8, 7.5, 8.2, and 9.1 multiplied by a power of 10. Meters are used to make measurem ...
CCR230PS3AGEVB Test Procedure
... 1. Turn ON AC power supply (not connected to the driver board), set its output voltage to 65 VAC using multi-meter, turn it OFF afterwards. 2. Connect LED board to driver board. 3. Connect AC power supply output to the driver board. 4. Connect one differential probe to the driver board AC input, thi ...
... 1. Turn ON AC power supply (not connected to the driver board), set its output voltage to 65 VAC using multi-meter, turn it OFF afterwards. 2. Connect LED board to driver board. 3. Connect AC power supply output to the driver board. 4. Connect one differential probe to the driver board AC input, thi ...
... the high voltage side of the network during both steady state and transient operation. One important FACTS component is the TCSC which allows rapid and continuous changes of the transmission line impedance . Active power flows along the compensated transmission line can be maintained at a specified ...
STMICROELECTRONICS M27C2 datasheet
... Note: 1. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP. 2. Sampled only, not 100% tested. 3. Speed obtained with High Speed AC measurement conditions. ...
... Note: 1. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP. 2. Sampled only, not 100% tested. 3. Speed obtained with High Speed AC measurement conditions. ...
Electric Drives Experiment 2 Two-Pole Switch-Mode DC Converter and
... Select the “Start Measuring” icon in the ControlDesk toolbar, and then turn on the inverter board’s analog power supply (i.e., set the analog power toggle switch to the “ON” position). Finally, turn on the 40V DC power supply. Using either the slider or the numeric input in ControlDesk, slowly chang ...
... Select the “Start Measuring” icon in the ControlDesk toolbar, and then turn on the inverter board’s analog power supply (i.e., set the analog power toggle switch to the “ON” position). Finally, turn on the 40V DC power supply. Using either the slider or the numeric input in ControlDesk, slowly chang ...
PB-400-CN - JBL Professional
... 3. The amplified signal from the ambient noise sensor input is available on 2 CobraNet® channels. 4. A-weighed, 10 to 22k Hz analyzer bandwidth, open input, 50 Ω load. 5. The device can either be accessed over RS-485 or over Ethernet by using the CobraNet® Serial Bridge protocol. The interfaces c ...
... 3. The amplified signal from the ambient noise sensor input is available on 2 CobraNet® channels. 4. A-weighed, 10 to 22k Hz analyzer bandwidth, open input, 50 Ω load. 5. The device can either be accessed over RS-485 or over Ethernet by using the CobraNet® Serial Bridge protocol. The interfaces c ...