AiT Semiconductor Inc. AiT Semiconductor Inc. DESCRIPTION
... Stresses above may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated in the Electrical Characteristics are not implied. Exposure to absolute maximum rating conditions for extended periods ...
... Stresses above may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated in the Electrical Characteristics are not implied. Exposure to absolute maximum rating conditions for extended periods ...
Alternate Class AB Amplifier Design This Class AB amplifier
... Design a CE/CC amplifier pair. Compare the voltage gains with and without bootstrapping. Assumptions and Design Parameters ...
... Design a CE/CC amplifier pair. Compare the voltage gains with and without bootstrapping. Assumptions and Design Parameters ...
Practical realization of propulsion unit with low voltage permanent
... The energy source is a series-parallel connection of modern LiFePo4 cells, which have currently some of the best properties. Parameters of one cell are: nominal capacity C=40 Ah, charging voltage 4.25 V, nominal voltage 3.2 V, the maximum charge and discharge current 3 CA, discharge pulse current 10 ...
... The energy source is a series-parallel connection of modern LiFePo4 cells, which have currently some of the best properties. Parameters of one cell are: nominal capacity C=40 Ah, charging voltage 4.25 V, nominal voltage 3.2 V, the maximum charge and discharge current 3 CA, discharge pulse current 10 ...
OnChipRegulators
... • Larger voltage drops can be accepted and thus smaller wire cross sections. • Together with the CCA wires the gain in material budget is substantial. • Regulators help to keep sensitive supply nodes quiet (power noise rejection) • The price is some 15% more power consumption on the chips ...
... • Larger voltage drops can be accepted and thus smaller wire cross sections. • Together with the CCA wires the gain in material budget is substantial. • Regulators help to keep sensitive supply nodes quiet (power noise rejection) • The price is some 15% more power consumption on the chips ...
Room Controller Spec Sheet
... junction boxes, while providing easy access to line voltage circuits. Low voltage devices are connected using Cat5 cables (ordered separately). UL 924 relay is provided on some units for automatic emergency lighting control. The UL 924 relay automatically tracks with output 1 and can be connected to ...
... junction boxes, while providing easy access to line voltage circuits. Low voltage devices are connected using Cat5 cables (ordered separately). UL 924 relay is provided on some units for automatic emergency lighting control. The UL 924 relay automatically tracks with output 1 and can be connected to ...
LR9641 DESCRIPTION FEATURES
... external components, such as ceramic input and output caps, as well as small inductors.LR9641 also employs a proprietary control scheme that switches the device into a power save mode during light load, thereby extending the range of high efficiency operation. An OVP function protects the IC itself ...
... external components, such as ceramic input and output caps, as well as small inductors.LR9641 also employs a proprietary control scheme that switches the device into a power save mode during light load, thereby extending the range of high efficiency operation. An OVP function protects the IC itself ...
An Improved Current Mode Logic Latch
... conventional and improved structures are shown in Fig.7(b). As the curves indicate, the average ratio of output swing to VDD is 70% for the improved structures, and 8% for the conventional ones. Under such circumstances the frequencies of the improved divider are only a little lower than those of th ...
... conventional and improved structures are shown in Fig.7(b). As the curves indicate, the average ratio of output swing to VDD is 70% for the improved structures, and 8% for the conventional ones. Under such circumstances the frequencies of the improved divider are only a little lower than those of th ...
AN1722
... Generally, the common fluorescent lamps can be considered only as a resistive load. In the CCFL lamps, instead, even if the tubes show a resistive behavior, a small but evident capacitive behavior is observed as it is shown in fig.7. In fig. 7 it is evident that the V-I Characteristic is linear unti ...
... Generally, the common fluorescent lamps can be considered only as a resistive load. In the CCFL lamps, instead, even if the tubes show a resistive behavior, a small but evident capacitive behavior is observed as it is shown in fig.7. In fig. 7 it is evident that the V-I Characteristic is linear unti ...
IES PE Short Course
... Equivalent circuit model for synchronous machine • However, when the machine is loaded, i.e., when there is a current flowing through the a-phase winding, then the terminal voltage will differ from the excitation voltage due to voltage drops caused by: 1. Armature reaction: This is the interaction ...
... Equivalent circuit model for synchronous machine • However, when the machine is loaded, i.e., when there is a current flowing through the a-phase winding, then the terminal voltage will differ from the excitation voltage due to voltage drops caused by: 1. Armature reaction: This is the interaction ...
Real-time adjustable gate current control IC solves dv/dt
... between switching performance and EMI with the design of the gate resistor including an optional gate-emitter capacitor. This procedure results in a fixed compromise, which must cover low load operation and high load operation as well. However, performance and therefore also efficiency is lost by th ...
... between switching performance and EMI with the design of the gate resistor including an optional gate-emitter capacitor. This procedure results in a fixed compromise, which must cover low load operation and high load operation as well. However, performance and therefore also efficiency is lost by th ...
AN-6206 Primary-Side Synchronous Rectifier (SR) Trigger Solution for Dual-Forward Converter
... primary-side MOSFETs are turned on. Then, SR1 should be turned off right before the primary-side MOSFETs are turned off. The freewheeling SR (SR2) should be turned on right after the primary-side MOSFETs are turned off. Then, SR2 should be turned off right before the primary-side MOSFETs are turned ...
... primary-side MOSFETs are turned on. Then, SR1 should be turned off right before the primary-side MOSFETs are turned off. The freewheeling SR (SR2) should be turned on right after the primary-side MOSFETs are turned off. Then, SR2 should be turned off right before the primary-side MOSFETs are turned ...
Lab 3
... generator filed on. Adjust the field supply to adjust the generator field current as described in the steps below. 2. Beginning from zero, increase the generator field current in steps of .25A until 1.25 . At each step readjust the rotor speed to synchronous using the stroboscope, then with the hand ...
... generator filed on. Adjust the field supply to adjust the generator field current as described in the steps below. 2. Beginning from zero, increase the generator field current in steps of .25A until 1.25 . At each step readjust the rotor speed to synchronous using the stroboscope, then with the hand ...
Electrical ballast
An electrical ballast is a device intended to limit the amount of current in an electric circuit. A familiar and widely used example is the inductive ballast used in fluorescent lamps, to limit the current through the tube, which would otherwise rise to destructive levels due to the tube's negative resistance characteristic.Ballasts vary in design complexity. They can be as simple as a series resistor or inductor, capacitors, or a combination thereof or as complex as electronic ballasts used with fluorescent lamps and high-intensity discharge lamps.