15 kV Megohmmeter Test Set
... The Test Set and the equipment to which it is connected are a source of high-voltage electrical energy. All persons performing or assisting in the tests must use all practical safety precautions to prevent contact with energized parts of the test equipment and associated circuits. Persons actually e ...
... The Test Set and the equipment to which it is connected are a source of high-voltage electrical energy. All persons performing or assisting in the tests must use all practical safety precautions to prevent contact with energized parts of the test equipment and associated circuits. Persons actually e ...
FAN21SV04 — TinyBuck™ 4 A, 24 V Single-Input Features
... FAN21SV04 facilitates single-supply operation for input voltages >6.5 V. At startup, the output of the internal regulator tracks the input voltage and comes into regulation (5 V) when VIN_Reg exceeds the UVLO threshold. The EN pin is released at the same time. The output voltage of the internal regu ...
... FAN21SV04 facilitates single-supply operation for input voltages >6.5 V. At startup, the output of the internal regulator tracks the input voltage and comes into regulation (5 V) when VIN_Reg exceeds the UVLO threshold. The EN pin is released at the same time. The output voltage of the internal regu ...
MAX253 Transformer Driver for Isolated RS-485 Interface _______________General Description
... ♦ Since the optocoupler outputs are relatively highimpedance nodes, they should be located as close as possible to the Maxim interface IC. This minimizes stray capacitance and maximizes data rate. Refer to the µMAX package information for pin spacing and physical dimensions. ...
... ♦ Since the optocoupler outputs are relatively highimpedance nodes, they should be located as close as possible to the Maxim interface IC. This minimizes stray capacitance and maximizes data rate. Refer to the µMAX package information for pin spacing and physical dimensions. ...
DC Coupling with 7 Series FPGAs GTX Transceivers
... 50Ω as possible, but with GPON line rates being very low, the reflections due to impedance mismatch should not be a major issue. Even if the VICM was close to 1.2V, the RX could have tolerated a TX launch amplitude of 2000 mVpp difference. The reason for this is that the gain due the resistor networ ...
... 50Ω as possible, but with GPON line rates being very low, the reflections due to impedance mismatch should not be a major issue. Even if the VICM was close to 1.2V, the RX could have tolerated a TX launch amplitude of 2000 mVpp difference. The reason for this is that the gain due the resistor networ ...
Article - Voltage Clamp Techniques
... voltage overshoot. Lags in the system will be caused by the need to charge the membrane capacity through an access resistance, and by the time constant(s) of the control amplifier itself. There will also be a delay in the measurement of membrane potential caused by capacitance at the input of the vo ...
... voltage overshoot. Lags in the system will be caused by the need to charge the membrane capacity through an access resistance, and by the time constant(s) of the control amplifier itself. There will also be a delay in the measurement of membrane potential caused by capacitance at the input of the vo ...
DESCRIPTION
... When using a style 2 or a style 3 encoder, the output polarity can be reversed by a jumper on the K661. When using a style 1, the output polarity may be reversed by reversing the ØA – ØB inputs. The K661 provides a full scale output of ±300 VDC at up to 3 milliamperes of current. The unit can be pro ...
... When using a style 2 or a style 3 encoder, the output polarity can be reversed by a jumper on the K661. When using a style 1, the output polarity may be reversed by reversing the ØA – ØB inputs. The K661 provides a full scale output of ±300 VDC at up to 3 milliamperes of current. The unit can be pro ...
04_ELC4345_Fall2013_DC_DC_Buck_PPT
... • Occurs for light loads, or low operating frequencies, where the inductor current eventually hits zero during the switchopen state • The diode opens to prevent backward current flow ...
... • Occurs for light loads, or low operating frequencies, where the inductor current eventually hits zero during the switchopen state • The diode opens to prevent backward current flow ...
how to use multimeter
... The meter section consists of scales and a pointer. The degree of deflection of the pointer enables the voltage value, current value and resistance value to be read. There are various kinds of scales. Check the position of the range selector described below and read the scale that matches the positi ...
... The meter section consists of scales and a pointer. The degree of deflection of the pointer enables the voltage value, current value and resistance value to be read. There are various kinds of scales. Check the position of the range selector described below and read the scale that matches the positi ...
KSC5026M NPN Silicon Transistor KSC5026M — NPN Silicon T ransistor
... sustain life, and (c) whose failure to perform when properly used in cause the failure of the life support device or system, or to affect its accordance with instructions for use provided in the labeling, can be safety or effectiveness. reasonably expected to result in a significant injury of the us ...
... sustain life, and (c) whose failure to perform when properly used in cause the failure of the life support device or system, or to affect its accordance with instructions for use provided in the labeling, can be safety or effectiveness. reasonably expected to result in a significant injury of the us ...
LT8613 – 42V, 6A Synchronous Step-Down
... The LT®8613 is a compact, high efficiency, high speed synchronous monolithic step-down switching regulator that consumes only 3µA of quiescent current. Top and bottom power switches are included with all necessary circuitry to minimize the need for external components. The built-in current sense amp ...
... The LT®8613 is a compact, high efficiency, high speed synchronous monolithic step-down switching regulator that consumes only 3µA of quiescent current. Top and bottom power switches are included with all necessary circuitry to minimize the need for external components. The built-in current sense amp ...
DS3906 Triple NV Low Step Size Variable Resistor Plus Memory General Description
... The DS3906 is intended for low resistance, small stepsize applications. It contains three nonvolatile (NV), lowtemperature coefficient, variable digital resistors that are capable of ohm and subohm increments when used in parallel with a fixed external resistor. All three of the DS3906’s resistors h ...
... The DS3906 is intended for low resistance, small stepsize applications. It contains three nonvolatile (NV), lowtemperature coefficient, variable digital resistors that are capable of ohm and subohm increments when used in parallel with a fixed external resistor. All three of the DS3906’s resistors h ...
Electrical ballast
An electrical ballast is a device intended to limit the amount of current in an electric circuit. A familiar and widely used example is the inductive ballast used in fluorescent lamps, to limit the current through the tube, which would otherwise rise to destructive levels due to the tube's negative resistance characteristic.Ballasts vary in design complexity. They can be as simple as a series resistor or inductor, capacitors, or a combination thereof or as complex as electronic ballasts used with fluorescent lamps and high-intensity discharge lamps.