AC Direct Off-Line Power Supplies
... indicates a high leakage current potential and shock hazard. Note: Any metallic part that reads overrange on the CURRENT/POWER LCD (blank display with a digit "1" on the left) is connected directly to one side of the AC line. ...
... indicates a high leakage current potential and shock hazard. Note: Any metallic part that reads overrange on the CURRENT/POWER LCD (blank display with a digit "1" on the left) is connected directly to one side of the AC line. ...
UF4004
... or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. ...
... or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. ...
PDF Download(PDF Type, 13Kbyte)
... The progress of system LSI performance has opened doors to increasing the functionality of cellular phones and is sustaining a rapidly expanding market. System-on-chip (SoC) performance is measured by factors such high-speed, as well as low-power consumption, which determines the battery life of cel ...
... The progress of system LSI performance has opened doors to increasing the functionality of cellular phones and is sustaining a rapidly expanding market. System-on-chip (SoC) performance is measured by factors such high-speed, as well as low-power consumption, which determines the battery life of cel ...
Energy and Power
... current that each appliance takes is calculated and then added to the others. The total current should not exceed the safe load current of the circuit Lighting circuits are usually fused for a maximum current of 5 amps and power or heating circuits for 10 or 15 amps. ...
... current that each appliance takes is calculated and then added to the others. The total current should not exceed the safe load current of the circuit Lighting circuits are usually fused for a maximum current of 5 amps and power or heating circuits for 10 or 15 amps. ...
L550A_M5400EX (Page 1)
... 3 Reduces Cross-Contamination Between Components The M5400-EX is designed to provide noise isolation between 5 isolated outlet banks including 2 high current outlets so that any noise created by an A/V component cannot contaminate the power going to equipment plugged into the other outlet banks. ...
... 3 Reduces Cross-Contamination Between Components The M5400-EX is designed to provide noise isolation between 5 isolated outlet banks including 2 high current outlets so that any noise created by an A/V component cannot contaminate the power going to equipment plugged into the other outlet banks. ...
Energy and Power Energy
... current that each appliance takes is calculated and then added to the others. The total current should not exceed the safe load current of the circuit Lighting circuits are usually fused for a maximum current of 5 amps and power or heating circuits for 10 or 15 amps. ...
... current that each appliance takes is calculated and then added to the others. The total current should not exceed the safe load current of the circuit Lighting circuits are usually fused for a maximum current of 5 amps and power or heating circuits for 10 or 15 amps. ...
Jun 1999 The LT1576: 200kHz, 1.5A Monolithic
... RFI radiation from the loop created by this path. These traces have a parasitic inductance of approximately 20nH/inch, which can cause an additional problem at higher operating voltages. At switch-off, the current flowing in the trace inductance causes a voltage spike. This is in addition to the inp ...
... RFI radiation from the loop created by this path. These traces have a parasitic inductance of approximately 20nH/inch, which can cause an additional problem at higher operating voltages. At switch-off, the current flowing in the trace inductance causes a voltage spike. This is in addition to the inp ...
Auxiliary Power Generator Products BLCD-20B
... emergency lighting fixtures and energizing them when normal utility power has been lost. The unit shall consist of relay switching circuitry, a test switch, a normal power indicator light and an alternate power indicator light contained in one 1.7”x 2.97”x 1.64” enclosure; shall sense normal power a ...
... emergency lighting fixtures and energizing them when normal utility power has been lost. The unit shall consist of relay switching circuitry, a test switch, a normal power indicator light and an alternate power indicator light contained in one 1.7”x 2.97”x 1.64” enclosure; shall sense normal power a ...
Project Helios
... • The multiplexer that was • An EN input on the device chosen for this project is used to enable or was the ADG409 by disable the device. When Analog Devices. disabled, all channels are switched off. • This part is a analog multiplexer with four differential channels. • The ADG409 switches one of fo ...
... • The multiplexer that was • An EN input on the device chosen for this project is used to enable or was the ADG409 by disable the device. When Analog Devices. disabled, all channels are switched off. • This part is a analog multiplexer with four differential channels. • The ADG409 switches one of fo ...
BP5047A24
... "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. ...
... "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. ...
