LV8136V - ONSemi
... The high state is when IN+ is greater than IN-, and the low state is the reverse. An amplitude of at least 100mVp-p (differential) is desirable for the Hall signal inputs. If noise on the Hall signals is a problem, insert capacitors between IN+ and IN- pins. If input is provided from a Hall IC, the ...
... The high state is when IN+ is greater than IN-, and the low state is the reverse. An amplitude of at least 100mVp-p (differential) is desirable for the Hall signal inputs. If noise on the Hall signals is a problem, insert capacitors between IN+ and IN- pins. If input is provided from a Hall IC, the ...
MP6507 - Monolithic Power System
... with dual, built-in full-bridges consisting of Nchannel power MOSFETs. It operates from a supply voltage range of 2.7V to 15V, and can deliver motor current up to 700mA per channel. The internal safety features include sinking and sourcing current limits implemented with external sensors, under-volt ...
... with dual, built-in full-bridges consisting of Nchannel power MOSFETs. It operates from a supply voltage range of 2.7V to 15V, and can deliver motor current up to 700mA per channel. The internal safety features include sinking and sourcing current limits implemented with external sensors, under-volt ...
Contents manual
... additional information, please contact your supplier. A hazardous situation may occur if the F110-P is not used for the purpose it was designed for or is used incorrectly. Please carefully note the information in this operating manual indicated by the pictograms: ...
... additional information, please contact your supplier. A hazardous situation may occur if the F110-P is not used for the purpose it was designed for or is used incorrectly. Please carefully note the information in this operating manual indicated by the pictograms: ...
SKY77711 数据资料DataSheet下载
... battery with an output in the 3.2 to 4.2 volt range. No VREF voltage is required. Power down is accomplished by setting the voltage on VENABLE to zero volts. No external supply side switch is needed as typical “off” leakage is a few microamperes with full primary voltage supplied from the battery. ...
... battery with an output in the 3.2 to 4.2 volt range. No VREF voltage is required. Power down is accomplished by setting the voltage on VENABLE to zero volts. No external supply side switch is needed as typical “off” leakage is a few microamperes with full primary voltage supplied from the battery. ...
4-Channel SDTV Video Amplifier with 6th-Order Filters and 6
... clamp option for CVBS, Y', and G'B'R' signals with sync. AC-coupled biasing for C'/P'B/P'R channels can easily be achieved by adding an external resistor. The THS7374 is the perfect choice for all video buffer applications. Its rail-to-rail output stage with 6-dB gain allows for both ac and dc line ...
... clamp option for CVBS, Y', and G'B'R' signals with sync. AC-coupled biasing for C'/P'B/P'R channels can easily be achieved by adding an external resistor. The THS7374 is the perfect choice for all video buffer applications. Its rail-to-rail output stage with 6-dB gain allows for both ac and dc line ...
Reproducibility conditions for the pulsed X
... charge circuit consists of a 12.5 µF/20 kV capacitor, in series connected with the anode-cathode discharge space. A short-circuit discharge of the capacitor was made to determine the electrical characteristics. The 232 nH equivalent inductance and the 30 mΩ equivalent resistance have been calculated ...
... charge circuit consists of a 12.5 µF/20 kV capacitor, in series connected with the anode-cathode discharge space. A short-circuit discharge of the capacitor was made to determine the electrical characteristics. The 232 nH equivalent inductance and the 30 mΩ equivalent resistance have been calculated ...
![Application Note [AN-004] Resistive Touch Panel Technologies](http://s1.studyres.com/store/data/000087727_1-d4cbc23776babe9b0e906bacf50dca62-300x300.png)
quad power supply - Electronix Express
... Description 0~8V/20A, 0~20V/10A 0~15V/7A, 0~30V/4A 0~30V/6A, 0~60V/3.3A ...
... Description 0~8V/20A, 0~20V/10A 0~15V/7A, 0~30V/4A 0~30V/6A, 0~60V/3.3A ...
Real Time Digital Simulation
... – adaptive via if, for, and while statements – user-defined subroutines – customize reporting of result analysis – automated plot printing • Efficient means of running numerous cases ...
... – adaptive via if, for, and while statements – user-defined subroutines – customize reporting of result analysis – automated plot printing • Efficient means of running numerous cases ...
PremiSys - IDenticard
... The Input Board can be housed in a sturdy and optionally lockable enclosure with its controller and/or other components. The Input Board itself includes the following components: o Sixteen general-purpose input points that can be used with supervision and can fulfill any input-point function: door-i ...
... The Input Board can be housed in a sturdy and optionally lockable enclosure with its controller and/or other components. The Input Board itself includes the following components: o Sixteen general-purpose input points that can be used with supervision and can fulfill any input-point function: door-i ...
CHAPTER 3 Sensors
... The industry-standard AD598 LVDT signal conditioner shown in Figure 3.4 (simplified form) performs all required LVDT signal processing. The on-chip excitation frequency oscillator can be set from 20 Hz to 20 kHz with a single external capacitor. Two absolute value circuits followed by two filters ar ...
... The industry-standard AD598 LVDT signal conditioner shown in Figure 3.4 (simplified form) performs all required LVDT signal processing. The on-chip excitation frequency oscillator can be set from 20 Hz to 20 kHz with a single external capacitor. Two absolute value circuits followed by two filters ar ...
Electron Transport in Single-Walled Carbon
... great deal of work has been done, the progress to date has been modest. For example, in tube synthesis, the diameter of the tubes can be controlled reasonably well,54 but not their chirality. The synthesized tubes remain a mixture of metals and semiconductors. In CVD, the general location for tube g ...
... great deal of work has been done, the progress to date has been modest. For example, in tube synthesis, the diameter of the tubes can be controlled reasonably well,54 but not their chirality. The synthesized tubes remain a mixture of metals and semiconductors. In CVD, the general location for tube g ...
ZW0201
... terminal of the crystal. The loading capacitor values depend on the total load capacitance, CL, specified for the crystal. The total load capacitance seen between the crystal terminals should equal CL for the crystal to oscillate at the specified frequency: ...
... terminal of the crystal. The loading capacitor values depend on the total load capacitance, CL, specified for the crystal. The total load capacitance seen between the crystal terminals should equal CL for the crystal to oscillate at the specified frequency: ...
TSUS5402
... time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed t ...
... time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed t ...
CM21566570
... An OTA is an amplifier where all nodes are low impedance except the input and output nodes. A useful feature of OTA is that its transconductance can be adjusted by the bias current. Filters made using the OTA can be tuned by changing the bias current Ibias[9]. Two practical concerns when designing a ...
... An OTA is an amplifier where all nodes are low impedance except the input and output nodes. A useful feature of OTA is that its transconductance can be adjusted by the bias current. Filters made using the OTA can be tuned by changing the bias current Ibias[9]. Two practical concerns when designing a ...
DIGITAL AC POWER MONITOR DSP- OSI
... Calibration of measurements is accomplished by applying a fixed, stable source of Volts and Amps of required accuracy (such as a Rotek Model 800A, or equivalent). The DSP instrument is sent a command string which causes the applied inputs to be established as reference values for calculation of RMS ...
... Calibration of measurements is accomplished by applying a fixed, stable source of Volts and Amps of required accuracy (such as a Rotek Model 800A, or equivalent). The DSP instrument is sent a command string which causes the applied inputs to be established as reference values for calculation of RMS ...
Rectifier
A rectifier is an electrical device that converts alternating current (AC), which periodically reverses direction, to direct current (DC), which flows in only one direction. The process is known as rectification. Physically, rectifiers take a number of forms, including vacuum tube diodes, mercury-arc valves, copper and selenium oxide rectifiers, semiconductor diodes, silicon-controlled rectifiers and other silicon-based semiconductor switches. Historically, even synchronous electromechanical switches and motors have been used. Early radio receivers, called crystal radios, used a ""cat's whisker"" of fine wire pressing on a crystal of galena (lead sulfide) to serve as a point-contact rectifier or ""crystal detector"".Rectifiers have many uses, but are often found serving as components of DC power supplies and high-voltage direct current power transmission systems. Rectification may serve in roles other than to generate direct current for use as a source of power. As noted, detectors of radio signals serve as rectifiers. In gas heating systems flame rectification is used to detect presence of a flame.Because of the alternating nature of the input AC sine wave, the process of rectification alone produces a DC current that, though unidirectional, consists of pulses of current. Many applications of rectifiers, such as power supplies for radio, television and computer equipment, require a steady constant DC current (as would be produced by a battery). In these applications the output of the rectifier is smoothed by an electronic filter (usually a capacitor) to produce a steady current.More complex circuitry that performs the opposite function, converting DC to AC, is called an inverter.