2.5Gbps SFP Transceiver
... The serial interface uses the 2-wire serial CMOS EEPROM protocol defined for the ATMEL AT24C02/04 family of components. When the serial protocol is activated, the host generates the serial clock signal (SCL). The positive edge clocks data into those segments of the EEPROM that are not write protecte ...
... The serial interface uses the 2-wire serial CMOS EEPROM protocol defined for the ATMEL AT24C02/04 family of components. When the serial protocol is activated, the host generates the serial clock signal (SCL). The positive edge clocks data into those segments of the EEPROM that are not write protecte ...
LM338K Datasheet
... possibility of problems. The adjustment terminal can be bypassed to ground on the LM338 to improve ripple rejection. This bypass capacitor prevents ripple form being amplified as the output voltage is increased. With a 10µF bypass capacitor 75dB ripple rejection is obtainable at any output level. In ...
... possibility of problems. The adjustment terminal can be bypassed to ground on the LM338 to improve ripple rejection. This bypass capacitor prevents ripple form being amplified as the output voltage is increased. With a 10µF bypass capacitor 75dB ripple rejection is obtainable at any output level. In ...
RF5322 3V TO 4.5V, 2.4GHz TO 2.5GHz LINEAR POWER AMPLIFIER Features
... band. The RF5322 has integrated input, interstage and output matching components thus allowing minimal bill of material (BOM) parts count in end applications. The RF5322 is designed primarily for IEEE802.11b/g/n WiFi applications where the available supply voltage and current are limited. This ampli ...
... band. The RF5322 has integrated input, interstage and output matching components thus allowing minimal bill of material (BOM) parts count in end applications. The RF5322 is designed primarily for IEEE802.11b/g/n WiFi applications where the available supply voltage and current are limited. This ampli ...
RAPID CHARGER FOR HIGH REPETITION RATE PULSE GENERATOR
... Special attention must be paid to the gate drive of the IGBT. We use a 9 A rated driver IC, the NCP4422. The rising edge of the gate drive waveform must be short and the driver must be able to supply enough current to absorb the Miller capacitance charge due to the falling collector waveform reflect ...
... Special attention must be paid to the gate drive of the IGBT. We use a 9 A rated driver IC, the NCP4422. The rising edge of the gate drive waveform must be short and the driver must be able to supply enough current to absorb the Miller capacitance charge due to the falling collector waveform reflect ...
AND8303/D Generating a 1.2 V Voltage Supply using the NCP102
... are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor doe ...
... are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor doe ...
AD537
... There are two independent adjustments: scale and offset. The first is trimmed by adjustment of the scaling resistor R and the second by the (optional) potentiometer connected to +VS and the VOS pins (“D” package only). Precise calibration requires the use of an accurate voltage standard set to the d ...
... There are two independent adjustments: scale and offset. The first is trimmed by adjustment of the scaling resistor R and the second by the (optional) potentiometer connected to +VS and the VOS pins (“D” package only). Precise calibration requires the use of an accurate voltage standard set to the d ...
PreLab 4 â Emitter Follower (Week of May 4th)
... connection to get extra high current gain (e.g. 10,000). This allows the input impedance of the follower to be over 10 kohm, even though the speaker impedance is only 16 ohm. Nice! TASK 3: Simulate the emitter follower shown in Figure ...
... connection to get extra high current gain (e.g. 10,000). This allows the input impedance of the follower to be over 10 kohm, even though the speaker impedance is only 16 ohm. Nice! TASK 3: Simulate the emitter follower shown in Figure ...
Technical Article
... be taken not to exceed the safe working voltage at the outputs of converters in series. This may be considerably lower than the dielectric strength test voltage which is a short-term test between outputs and ground. The output ripple of converters in series is additive but this of course does not ch ...
... be taken not to exceed the safe working voltage at the outputs of converters in series. This may be considerably lower than the dielectric strength test voltage which is a short-term test between outputs and ground. The output ripple of converters in series is additive but this of course does not ch ...
PSM05S93E5-A
... All capacitors should be mounted as close to the terminals as possible. (C1: good temperature, frequency characteristic electrolytic type and C2:0.22μ-2μF, good temperature, frequency and DC bias characteristic ceramic type are recommended.) Input drive is High-active type. There is a minimum 3.3kΩ ...
... All capacitors should be mounted as close to the terminals as possible. (C1: good temperature, frequency characteristic electrolytic type and C2:0.22μ-2μF, good temperature, frequency and DC bias characteristic ceramic type are recommended.) Input drive is High-active type. There is a minimum 3.3kΩ ...
Greenock Academy Physics Department
... LEDs are semiconductor devices that require a very small current. For this reason they must be protected by a series resistor when they are connected to a power supply. The series resistor limits the amount of current flowing in the circuit and ensures that it doesn’t exceed the value that the LED ...
... LEDs are semiconductor devices that require a very small current. For this reason they must be protected by a series resistor when they are connected to a power supply. The series resistor limits the amount of current flowing in the circuit and ensures that it doesn’t exceed the value that the LED ...
B61089QDR, Dual port negative voltage tracking SLIC protector
... (Subscriber Line Interface Circuit) cards implementing negative ringing only. This single 8-pin component provides protection for two SLIC ports (T1/R1 & T2/R2) by shunting positive and negative surges to the ground reference. The negative surges are diverted to ground through the SCRs which are con ...
... (Subscriber Line Interface Circuit) cards implementing negative ringing only. This single 8-pin component provides protection for two SLIC ports (T1/R1 & T2/R2) by shunting positive and negative surges to the ground reference. The negative surges are diverted to ground through the SCRs which are con ...
Schmitt trigger
In electronics a Schmitt trigger is a comparator circuit with hysteresis implemented by applying positive feedback to the noninverting input of a comparator or differential amplifier. It is an active circuit which converts an analog input signal to a digital output signal. The circuit is named a ""trigger"" because the output retains its value until the input changes sufficiently to trigger a change. In the non-inverting configuration, when the input is higher than a chosen threshold, the output is high. When the input is below a different (lower) chosen threshold the output is low, and when the input is between the two levels the output retains its value. This dual threshold action is called hysteresis and implies that the Schmitt trigger possesses memory and can act as a bistable multivibrator (latch or flip-flop). There is a close relation between the two kinds of circuits: a Schmitt trigger can be converted into a latch and a latch can be converted into a Schmitt trigger.Schmitt trigger devices are typically used in signal conditioning applications to remove noise from signals used in digital circuits, particularly mechanical contact bounce. They are also used in closed loop negative feedback configurations to implement relaxation oscillators, used in function generators and switching power supplies.