High-Frequency Link: A Solution for Using Only One DC Source in
... with MOSFETs or insulated-gate bipolar transistors (IGBTs), a small toroidal ferrite transformer, and simple diode rectifiers. ...
... with MOSFETs or insulated-gate bipolar transistors (IGBTs), a small toroidal ferrite transformer, and simple diode rectifiers. ...
Final Design Report - University of Idaho
... The full wave bridge rectifier used in the circuit is made by Center Semiconductor Corporation. Alternating current from the local utility supplying 120 V and 15 A at 60 Hz is the input for the rectifier. The voltage is then dropped across two diodes on the positive and negative period of the sine w ...
... The full wave bridge rectifier used in the circuit is made by Center Semiconductor Corporation. Alternating current from the local utility supplying 120 V and 15 A at 60 Hz is the input for the rectifier. The voltage is then dropped across two diodes on the positive and negative period of the sine w ...
LT1033 - 3A Negative Adjustable Regulator
... ensure a low impedance at 1MHz. The output capacitor should be located within a few inches of the regulator to keep lead impedance to a minimum. The following caution should be noted: if the output voltage is greater than 6V and an output capacitor greater than 20µF has been used, it is possible to ...
... ensure a low impedance at 1MHz. The output capacitor should be located within a few inches of the regulator to keep lead impedance to a minimum. The following caution should be noted: if the output voltage is greater than 6V and an output capacitor greater than 20µF has been used, it is possible to ...
PHYSICS 536 GENERAL INSTRUCTIONS FOR LABORATORY A. INTRODUCTION
... voltage but is insensitive to the average voltage. This mode is convenient for most sine wave measurements. It must be used to observe small variations of large voltages. The capacitor will produce a DC level shift for pulses (see notes Section 3.04). 5.3* DC INPUT. The “DC” mode uses a direct conne ...
... voltage but is insensitive to the average voltage. This mode is convenient for most sine wave measurements. It must be used to observe small variations of large voltages. The capacitor will produce a DC level shift for pulses (see notes Section 3.04). 5.3* DC INPUT. The “DC” mode uses a direct conne ...
MAX619 Regulated 5V Charge-Pump DC
... For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800 ...
... For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800 ...
inductive high voltage pulse generator based on resonance system
... A high voltage pulse generator based on inductive intermediate energy storage has been constructed. The current switching technique used in the generator is based on a resonance system. Opening switches for high currents are generally difficult to construct and the switch used here has proven to tur ...
... A high voltage pulse generator based on inductive intermediate energy storage has been constructed. The current switching technique used in the generator is based on a resonance system. Opening switches for high currents are generally difficult to construct and the switch used here has proven to tur ...
UC29431 数据资料 dataSheet 下载
... and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s te ...
... and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s te ...
AP5101 1.5A Step-Down Converter with 1.4MHz Switching Frequency
... With the low series resistance power switch it enables a constant output current of up to 1.5A over a wide input supply range. The load and line regulation has excellent response time over the operating input voltage and temperature range. The AP5101 is self protected, through a cycle-by-cycle curre ...
... With the low series resistance power switch it enables a constant output current of up to 1.5A over a wide input supply range. The load and line regulation has excellent response time over the operating input voltage and temperature range. The AP5101 is self protected, through a cycle-by-cycle curre ...
AP65552 - Diodes Incorporated
... If the junction temperature of the device reaches the thermal shutdown limit of 160°C, the AP65552 shuts itself off, and both HMOS and LMOS will be turned off. The output is discharged with the internal transistor. When the junction cools to the required level (130°C nominal), the device initiates s ...
... If the junction temperature of the device reaches the thermal shutdown limit of 160°C, the AP65552 shuts itself off, and both HMOS and LMOS will be turned off. The output is discharged with the internal transistor. When the junction cools to the required level (130°C nominal), the device initiates s ...
OPA343 OPA2343 OPA4343 SINGLE-SUPPLY, RAIL-TO-RAIL
... 500mV beyond the supply rails. Output voltage swings to within 1mV of the supply rails with a 100kΩ load. They offer excellent dynamic response (BW = 5.5MHz, SR = 6V/µs), yet quiescent current is only 850µA. Dual and quad designs feature completely independent circuitry for lowest crosstalk and free ...
... 500mV beyond the supply rails. Output voltage swings to within 1mV of the supply rails with a 100kΩ load. They offer excellent dynamic response (BW = 5.5MHz, SR = 6V/µs), yet quiescent current is only 850µA. Dual and quad designs feature completely independent circuitry for lowest crosstalk and free ...
Difet OPA627 OPA637 Precision High-Speed
... The OPA627/637 is laser-trimmed for low offset voltage and drift, so many circuits will not require external adjustment. Figure 3 shows the optional connection of an external potentiometer to adjust offset voltage. This adjustment should not be used to compensate for offsets created elsewhere in a s ...
... The OPA627/637 is laser-trimmed for low offset voltage and drift, so many circuits will not require external adjustment. Figure 3 shows the optional connection of an external potentiometer to adjust offset voltage. This adjustment should not be used to compensate for offsets created elsewhere in a s ...
Supplement to EMC Filter Built-in Type 0.1kW to 4
... circuit protection must be provided in accordance with the National Electrical Code and any additional local codes. 1. Solid state motor overload protection (motor protection by electronic thermal overload relay) is provided in each model. Adjust function codes F10 to F12 and H89 to set the protecti ...
... circuit protection must be provided in accordance with the National Electrical Code and any additional local codes. 1. Solid state motor overload protection (motor protection by electronic thermal overload relay) is provided in each model. Adjust function codes F10 to F12 and H89 to set the protecti ...
Voltage regulator
A voltage regulator is designed to automatically maintain a constant voltage level. A voltage regulator may be a simple ""feed-forward"" design or may include negative feedback control loops. It may use an electromechanical mechanism, or electronic components. Depending on the design, it may be used to regulate one or more AC or DC voltages.Electronic voltage regulators are found in devices such as computer power supplies where they stabilize the DC voltages used by the processor and other elements. In automobile alternators and central power station generator plants, voltage regulators control the output of the plant. In an electric power distribution system, voltage regulators may be installed at a substation or along distribution lines so that all customers receive steady voltage independent of how much power is drawn from the line.