NVT2003/04/06 1. General description Bidirectional voltage-level translator for open-drain and
... NXP Semiconductors ...
... NXP Semiconductors ...
MAX917–MAX920 SOT23, 1.8V, Nanopower, Beyond-the-Rails Comparators With/Without Reference General Description
... a push-pull output stage that sinks and sources current. Large internal output drivers allow rail-to-rail output swing with loads up to 8mA. The MAX918/MAX920 have an open-drain output stage that makes them suitable for mixed-voltage system design. ...
... a push-pull output stage that sinks and sources current. Large internal output drivers allow rail-to-rail output swing with loads up to 8mA. The MAX918/MAX920 have an open-drain output stage that makes them suitable for mixed-voltage system design. ...
USB Host Charger Identification Analog Switch MAX14550E General Description Features
... Charging Specification Revision 1.0 and a set resistor bias for AppleM-compliant devices. The MAX14550E features a high-performance Hi-Speed USB switch with low 4pF (typ) on-capacitance and low 4I (typ) on-resistance. In addition, the MAX14550E features two digital inputs (CB0 and CB1) to switch bet ...
... Charging Specification Revision 1.0 and a set resistor bias for AppleM-compliant devices. The MAX14550E features a high-performance Hi-Speed USB switch with low 4pF (typ) on-capacitance and low 4I (typ) on-resistance. In addition, the MAX14550E features two digital inputs (CB0 and CB1) to switch bet ...
$doc.title
... reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Phil ...
... reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Phil ...
TDA8023 1. General description Low power IC card interface
... By definition, a device that sends a signal is called a transmitter and a device that receives the signal is called a receiver. The device that controls the signal is called the master. The devices that are controlled by the master are called slaves. Each byte is followed by one acknowledge bit. Thi ...
... By definition, a device that sends a signal is called a transmitter and a device that receives the signal is called a receiver. The device that controls the signal is called the master. The devices that are controlled by the master are called slaves. Each byte is followed by one acknowledge bit. Thi ...
Vdc
... Save screen snapshot #3 Top curve: Audio output of CD player to inverter, Bottom curve: Output of inverter to speakers (scope set to average over one cycle) ...
... Save screen snapshot #3 Top curve: Audio output of CD player to inverter, Bottom curve: Output of inverter to speakers (scope set to average over one cycle) ...
AD5170 数据手册DataSheet下载
... 5/05—Rev. A to Rev. B Changes to Table 1 ............................................................................ 3 Changes to Table 2 ............................................................................ 5 Changes to Pin Function Descriptions .......................................... 9 ...
... 5/05—Rev. A to Rev. B Changes to Table 1 ............................................................................ 3 Changes to Table 2 ............................................................................ 5 Changes to Pin Function Descriptions .......................................... 9 ...
50 MHz to 9 GHz 65 dB TruPwr Detector ADL5902
... reading is presented directly in decibels and is scaled 1.06 V per decade, or 53 mV/dB; other slopes are easily arranged. In controller mode, the voltage applied to VSET determines the power level required at the input to null the deviation from the set point. The output buffer can provide high load ...
... reading is presented directly in decibels and is scaled 1.06 V per decade, or 53 mV/dB; other slopes are easily arranged. In controller mode, the voltage applied to VSET determines the power level required at the input to null the deviation from the set point. The output buffer can provide high load ...
Design of Power-Rail ESD Clamp Circuit with Adjustable Holding
... A 3V voltage pulse with a rise time of 5ns was applied to the VDD node while the VSS node was grounded to simulate the fast-rising edge of the HBM ESD event, as illustrated in Fig. 4. As shown in Fig. 4(a), the coupling voltage at node A is exactly equal to 0.34VDD before the ESD-transient detection ...
... A 3V voltage pulse with a rise time of 5ns was applied to the VDD node while the VSS node was grounded to simulate the fast-rising edge of the HBM ESD event, as illustrated in Fig. 4. As shown in Fig. 4(a), the coupling voltage at node A is exactly equal to 0.34VDD before the ESD-transient detection ...
Transistor–transistor logic
Transistor–transistor logic (TTL) is a class of digital circuits built from bipolar junction transistors (BJT) and resistors. It is called transistor–transistor logic because both the logic gating function (e.g., AND) and the amplifying function are performed by transistors (contrast with RTL and DTL).TTL is notable for being a widespread integrated circuit (IC) family used in many applications such as computers, industrial controls, test equipment and instrumentation, consumer electronics, synthesizers, etc. The designation TTL is sometimes used to mean TTL-compatible logic levels, even when not associated directly with TTL integrated circuits, for example as a label on the inputs and outputs of electronic instruments.After their introduction in integrated circuit form in 1963 by Sylvania, TTL integrated circuits were manufactured by several semiconductor companies, with the 7400 series (also called 74xx) by Texas Instruments becoming particularly popular. TTL manufacturers offered a wide range of logic gate, flip-flops, counters, and other circuits. Several variations from the original bipolar TTL concept were developed, giving circuits with higher speed or lower power dissipation to allow optimization of a design. TTL circuits simplified design of systems compared to earlier logic families, offering superior speed to resistor–transistor logic (RTL) and easier design layout than emitter-coupled logic (ECL). The design of the input and outputs of TTL gates allowed many elements to be interconnected.TTL became the foundation of computers and other digital electronics. Even after much larger scale integrated circuits made multiple-circuit-board processors obsolete, TTL devices still found extensive use as the ""glue"" logic interfacing more densely integrated components. TTL devices were originally made in ceramic and plastic dual-in-line (DIP) packages, and flat-pack form. TTL chips are now also made in surface-mount packages. Successors to the original bipolar TTL logic often are interchangeable in function with the original circuits, but with improved speed or lower power dissipation.