SN74AVC16722 数据资料 dataSheet 下载
... Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
... Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
LP2985 - Texas Instruments
... Where the value of RθJA for the SOT-23 package is 169.0°C/W in a typical PC board mounting. Exceeding the maximum allowable dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. For 12-V option, output voltage survival: –0.3 to +16 V. If used in a dual-su ...
... Where the value of RθJA for the SOT-23 package is 169.0°C/W in a typical PC board mounting. Exceeding the maximum allowable dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. For 12-V option, output voltage survival: –0.3 to +16 V. If used in a dual-su ...
Manual.
... The scope and the display parameters (CH1 Volt/div, CH2 Volt/div, time base Sec/div, Trigger Channel, Trigger rise/fall, Trigger Level) appear on the bottom of the screen. The Up and Down arrow keys highlight one of the fields below. The required field can be selected by touching it and can be chang ...
... The scope and the display parameters (CH1 Volt/div, CH2 Volt/div, time base Sec/div, Trigger Channel, Trigger rise/fall, Trigger Level) appear on the bottom of the screen. The Up and Down arrow keys highlight one of the fields below. The required field can be selected by touching it and can be chang ...
$doc.title
... 2. This is the increase in supply current for each input at the specified voltage level other than VCC or GND 3. This parameter is valid for any VCC between 0V and 1.2V with a transition time of up to 10msec. From VCC = 1.2V to VCC = 3.3V ± 0.3V a transition time of 100µsec is permitted. This parame ...
... 2. This is the increase in supply current for each input at the specified voltage level other than VCC or GND 3. This parameter is valid for any VCC between 0V and 1.2V with a transition time of up to 10msec. From VCC = 1.2V to VCC = 3.3V ± 0.3V a transition time of 100µsec is permitted. This parame ...
a Low Noise, High Throughput 24-Bit Sigma-Delta ADC AD7731
... These calibration and span limits apply provided the absolute input voltage specification is obeyed. The offset calibration limit applies to both the unipolar zero point and the bipolar ...
... These calibration and span limits apply provided the absolute input voltage specification is obeyed. The offset calibration limit applies to both the unipolar zero point and the bipolar ...
PCAL9555A 1. General description Low-voltage 16-bit I
... I2C-bus to parallel port expander Operating power supply voltage range of 1.65 V to 5.5 V Low standby current consumption: 1.5 A (typical at 5 V VDD) 1.0 A (typical at 3.3 V VDD) Schmitt-trigger action allows slow input transition and better switching noise immunity at the SCL and SDA ...
... I2C-bus to parallel port expander Operating power supply voltage range of 1.65 V to 5.5 V Low standby current consumption: 1.5 A (typical at 5 V VDD) 1.0 A (typical at 3.3 V VDD) Schmitt-trigger action allows slow input transition and better switching noise immunity at the SCL and SDA ...
BDTIC www.BDTIC.com/infineon Power Management and Multimarket
... 4) TOTP, range specifies the typical temperature tuning range achievable at a 10 % reduction of LED current using resistors with 1 % accuracy. Temperatures specified refer to junction temperature on chip. Accuracy of the temperature sensor is typical ±5 K. Any resistor value RTadj ≥ 0 Ω can be selec ...
... 4) TOTP, range specifies the typical temperature tuning range achievable at a 10 % reduction of LED current using resistors with 1 % accuracy. Temperatures specified refer to junction temperature on chip. Accuracy of the temperature sensor is typical ±5 K. Any resistor value RTadj ≥ 0 Ω can be selec ...
Transistor–transistor logic
Transistor–transistor logic (TTL) is a class of digital circuits built from bipolar junction transistors (BJT) and resistors. It is called transistor–transistor logic because both the logic gating function (e.g., AND) and the amplifying function are performed by transistors (contrast with RTL and DTL).TTL is notable for being a widespread integrated circuit (IC) family used in many applications such as computers, industrial controls, test equipment and instrumentation, consumer electronics, synthesizers, etc. The designation TTL is sometimes used to mean TTL-compatible logic levels, even when not associated directly with TTL integrated circuits, for example as a label on the inputs and outputs of electronic instruments.After their introduction in integrated circuit form in 1963 by Sylvania, TTL integrated circuits were manufactured by several semiconductor companies, with the 7400 series (also called 74xx) by Texas Instruments becoming particularly popular. TTL manufacturers offered a wide range of logic gate, flip-flops, counters, and other circuits. Several variations from the original bipolar TTL concept were developed, giving circuits with higher speed or lower power dissipation to allow optimization of a design. TTL circuits simplified design of systems compared to earlier logic families, offering superior speed to resistor–transistor logic (RTL) and easier design layout than emitter-coupled logic (ECL). The design of the input and outputs of TTL gates allowed many elements to be interconnected.TTL became the foundation of computers and other digital electronics. Even after much larger scale integrated circuits made multiple-circuit-board processors obsolete, TTL devices still found extensive use as the ""glue"" logic interfacing more densely integrated components. TTL devices were originally made in ceramic and plastic dual-in-line (DIP) packages, and flat-pack form. TTL chips are now also made in surface-mount packages. Successors to the original bipolar TTL logic often are interchangeable in function with the original circuits, but with improved speed or lower power dissipation.