Introduction to sensors
... • absolute position : GPS • light level : photo cell, camera • sound level : microphone • deformation : strain gauge • temperature : thermometer • gravity : inclinometer (accelerometer) • acceleration (linear) : accelerometer • rotational speed : gyroscope • contact : switch • current : current tran ...
... • absolute position : GPS • light level : photo cell, camera • sound level : microphone • deformation : strain gauge • temperature : thermometer • gravity : inclinometer (accelerometer) • acceleration (linear) : accelerometer • rotational speed : gyroscope • contact : switch • current : current tran ...
Specifications
... Print length (shot length) Continuous, 20 cm, 50 cm, 1 m, 2 m Memory length 2.5 M/CH fixed, max. 1000 div (depends on chart speed) Numerical printing Digital values Intervals: 1 s, 2 s, 5 s, 10 s, 15 s, 20 s, 30 s, 1 min, 2 min, 5 min, 10 min, ...
... Print length (shot length) Continuous, 20 cm, 50 cm, 1 m, 2 m Memory length 2.5 M/CH fixed, max. 1000 div (depends on chart speed) Numerical printing Digital values Intervals: 1 s, 2 s, 5 s, 10 s, 15 s, 20 s, 30 s, 1 min, 2 min, 5 min, 10 min, ...
Z4000 Envelope Generator
... will become a positive voltage and CCW will turn it into a negative voltage. The LED will indicate those states with either an unlit, red, or yellow state, respectfully. In addition, the envelope signal passes through yet another cv processor circuit called the Deviater. What this does is add a stat ...
... will become a positive voltage and CCW will turn it into a negative voltage. The LED will indicate those states with either an unlit, red, or yellow state, respectfully. In addition, the envelope signal passes through yet another cv processor circuit called the Deviater. What this does is add a stat ...
Lab 7 - Op-amps - PSU MNE
... Introduction and Background (Note: To save paper, you do not need to print this section for your lab report.) An operational amplifier (usually abbreviated op-amp) is an integrated circuit that amplifies the difference in voltage signal across its input terminals. In a so-called open-loop configurat ...
... Introduction and Background (Note: To save paper, you do not need to print this section for your lab report.) An operational amplifier (usually abbreviated op-amp) is an integrated circuit that amplifies the difference in voltage signal across its input terminals. In a so-called open-loop configurat ...
10-Bit 60 MSPS A/D Converter AD9020
... aperture delay. This is especially important when sampling high slew rate signals in wide bandwidth systems. Aperture uncertainty is one of the factors that degrade dynamic performance as the analog input frequency is increased. ...
... aperture delay. This is especially important when sampling high slew rate signals in wide bandwidth systems. Aperture uncertainty is one of the factors that degrade dynamic performance as the analog input frequency is increased. ...
Note - Lcfalondon
... long string of 0s or 1s can cause a drift in the baseline ( called baseline wandering) and make it difficult for the receiver to decode correctly. A good line coding scheme needs to prevent baseline wandering ...
... long string of 0s or 1s can cause a drift in the baseline ( called baseline wandering) and make it difficult for the receiver to decode correctly. A good line coding scheme needs to prevent baseline wandering ...
ece2201_lab4
... measure resistance, which affects the resistance measured in the triode region. The problem: in the 2kΩ range, the DVM injects a larger current than in the 20kΩ range. This causes a larger value of vDS, violating the “small vDS” condition for the resistive portion of the triode region. So, even thou ...
... measure resistance, which affects the resistance measured in the triode region. The problem: in the 2kΩ range, the DVM injects a larger current than in the 20kΩ range. This causes a larger value of vDS, violating the “small vDS” condition for the resistive portion of the triode region. So, even thou ...
2 5 1 The power converter derives the heater, line blanking and EHT
... potentiometers used for setting up circuit parameters during manufacture and after repair There are five potentiometers for adjusting the picture size position and height, and two others for optimising the performance of the sound and line Phase locker; loops implemented within the IC. 2.2 Tube Desi ...
... potentiometers used for setting up circuit parameters during manufacture and after repair There are five potentiometers for adjusting the picture size position and height, and two others for optimising the performance of the sound and line Phase locker; loops implemented within the IC. 2.2 Tube Desi ...
Document
... A digital output in parallel with the sensing element (shown in Figure 2) is called a pull-down contact. The current-limiting resistor pulls the voltage up across the sensing element of the digital input. In this configuration, current flowing through the sensing element is a logical 0 to the contro ...
... A digital output in parallel with the sensing element (shown in Figure 2) is called a pull-down contact. The current-limiting resistor pulls the voltage up across the sensing element of the digital input. In this configuration, current flowing through the sensing element is a logical 0 to the contro ...
Fluke ScopeMeter Series IIB selection guide
... Step 3: With selection complete, setup is automatic 5GS/s, 200 ps random repetitive sampling for better accuracy Verifying repetitive signals - such as clock pulses, carrier waves, and fast rise time signals - in computing or communications equipment can be difficult because high frequencies are har ...
... Step 3: With selection complete, setup is automatic 5GS/s, 200 ps random repetitive sampling for better accuracy Verifying repetitive signals - such as clock pulses, carrier waves, and fast rise time signals - in computing or communications equipment can be difficult because high frequencies are har ...
Lab 2 - Mechanical Engineering
... should be the objectives of the lab. Include what should be accomplished or learned through performing this experiment. ...
... should be the objectives of the lab. Include what should be accomplished or learned through performing this experiment. ...
MT-068 TUTORIAL Difference and Current Sense Amplifiers
... The AD8210 is comprised of two main blocks, a differential amplifier and an instrumentation amplifier. A load current flowing through the external shunt resistor produces a voltage at the input terminals of the AD8210. The input terminals are connected to the differential amplifier (A1) by R1 and R2 ...
... The AD8210 is comprised of two main blocks, a differential amplifier and an instrumentation amplifier. A load current flowing through the external shunt resistor produces a voltage at the input terminals of the AD8210. The input terminals are connected to the differential amplifier (A1) by R1 and R2 ...
PawelkiewiczJake1_3_2
... Along with combinational logic, sequential logic is a fundamental building block of digital electronics. The output values of sequential logic depend not only on the current input values (i.e., combinational logic), but also on previous output values. Thus, sequential logic requires a clock signal t ...
... Along with combinational logic, sequential logic is a fundamental building block of digital electronics. The output values of sequential logic depend not only on the current input values (i.e., combinational logic), but also on previous output values. Thus, sequential logic requires a clock signal t ...
Oscilloscope types
This is a subdivision of the Oscilloscope article, discussing the various types and models of oscilloscopes in greater detail.