Dual Channel High-IP3 100MHz – 6GHz Active Mixer ADL5802 Preliminary Technical Data
... subject to high input levels. A bias adjust feature allows the input linearity, SSB Noise Figure, and DC current to be optimized using a single control pin. The high input linearity allows the device to be used in demanding cellular applications where in-band blocking signals may otherwise result in ...
... subject to high input levels. A bias adjust feature allows the input linearity, SSB Noise Figure, and DC current to be optimized using a single control pin. The high input linearity allows the device to be used in demanding cellular applications where in-band blocking signals may otherwise result in ...
University of North Carolina, Charlotte Department of Electrical and Computer Engineering
... need to remember how a pole and zero affect the magnitude of the gain. We want to design our bass-boost circuit so that we meet the following specifications: a. A constant gain of approximately 35dB for input frequencies below about 100Hz b. A gain that falls at -20dB/decade between 100Hz and 10kHz ...
... need to remember how a pole and zero affect the magnitude of the gain. We want to design our bass-boost circuit so that we meet the following specifications: a. A constant gain of approximately 35dB for input frequencies below about 100Hz b. A gain that falls at -20dB/decade between 100Hz and 10kHz ...
LNK302/304-306 LinkSwitch-TN Family
... EU requirements Applications • Appliances and timers • LED drivers and industrial controls ...
... EU requirements Applications • Appliances and timers • LED drivers and industrial controls ...
OPA656 Wideband, Unity-Gain Stable, FET-Input OPERATIONAL AMPLIFIER FEATURES
... Voltage-feedback op amps, unlike current feedback products, can use a wide range of resistor values to set their gain. To retain a controlled frequency response for the noninverting voltage amplifier of Figure 1, the parallel combination of RF || RG should always < 200Ω. In the noninverting configur ...
... Voltage-feedback op amps, unlike current feedback products, can use a wide range of resistor values to set their gain. To retain a controlled frequency response for the noninverting voltage amplifier of Figure 1, the parallel combination of RF || RG should always < 200Ω. In the noninverting configur ...
Power Factor Control..
... the reference voltage used by the error amplifier to regulate the output DC voltage. With pin 13 open, the refer- low line in the US (85VAC) to high line in Europe ence voltage is typically 7.5V. An internal current source (255VAC). This is done using line feedforward, which delivers approximately - ...
... the reference voltage used by the error amplifier to regulate the output DC voltage. With pin 13 open, the refer- low line in the US (85VAC) to high line in Europe ence voltage is typically 7.5V. An internal current source (255VAC). This is done using line feedforward, which delivers approximately - ...
MAX846A Cost-Saving Multichemistry Battery-Charger System _______________General Description
... chemistries (Li-Ion, NiMH or NiCd cells) to be charged using one circuit. In its simplest application, the MAX846A is a standalone, current-limited float voltage source that charges Li-Ion cells. It can also be paired up with a low-cost microcontroller (µC) to build a universal charger capable of ch ...
... chemistries (Li-Ion, NiMH or NiCd cells) to be charged using one circuit. In its simplest application, the MAX846A is a standalone, current-limited float voltage source that charges Li-Ion cells. It can also be paired up with a low-cost microcontroller (µC) to build a universal charger capable of ch ...
AD8022 (Rev. C)
... The maximum power that can be safely dissipated by the AD8022 is limited by the associated rise in junction temperature. The maximum safe junction temperature for plastic encapsulated devices is determined by the glass transition temperature of the plastic, approximately 150°C. Temporarily exceeding ...
... The maximum power that can be safely dissipated by the AD8022 is limited by the associated rise in junction temperature. The maximum safe junction temperature for plastic encapsulated devices is determined by the glass transition temperature of the plastic, approximately 150°C. Temporarily exceeding ...
LTC1152 - Rail-to-Rail Input Rail-to-Rail Output Zero-Drift Op Amp
... the bandwidth of the LTC1152. With 0.1µF from pin 5 to pin 6, the LTC1152’s gain-bandwidth product is reduced from 700kHz to around 200Hz. Note that compensation capacitors greater than 1µF can cause latch-up under severe output fault conditions; this can be prevented by clamping pin 5 to each suppl ...
... the bandwidth of the LTC1152. With 0.1µF from pin 5 to pin 6, the LTC1152’s gain-bandwidth product is reduced from 700kHz to around 200Hz. Note that compensation capacitors greater than 1µF can cause latch-up under severe output fault conditions; this can be prevented by clamping pin 5 to each suppl ...
Application Note AN-3010 Using the QVE00033 Surface Mount Phototransistor Optical Interrupter Switch
... phototransistor. This light generates a photocurrent that flows from the collector to emitter of the phototransistor. This increase in current develops a voltage across the collector load resistor. The collector to emitter voltage can be calculated from equation 2. +5V 680Ω ...
... phototransistor. This light generates a photocurrent that flows from the collector to emitter of the phototransistor. This increase in current develops a voltage across the collector load resistor. The collector to emitter voltage can be calculated from equation 2. +5V 680Ω ...
a Ultralow Noise, High Speed, BiFET Op Amp AD745
... errors. This is demonstrated in Figure 3, which compares input voltage noise vs. input source resistance of the OP37 and the AD745 opamps. From this figure, it is clear that at high source impedance the low current noise of the AD745 also provides lower total noise. It is also important to note that ...
... errors. This is demonstrated in Figure 3, which compares input voltage noise vs. input source resistance of the OP37 and the AD745 opamps. From this figure, it is clear that at high source impedance the low current noise of the AD745 also provides lower total noise. It is also important to note that ...
