AD537
... first is trimmed by adjustment of the scaling resistor R and the second by the (optional) potentiometer connected to +VS and the VOS pins (“D” package only). Precise calibration requires the use of an accurate voltage standard set to the desired FS value and a frequency meter; a scope is useful for ...
... first is trimmed by adjustment of the scaling resistor R and the second by the (optional) potentiometer connected to +VS and the VOS pins (“D” package only). Precise calibration requires the use of an accurate voltage standard set to the desired FS value and a frequency meter; a scope is useful for ...
a High Speed, Low Noise Quad Operational Amplifier OP471
... and source resistance. For RS < 1 kW the total noise is dominated by the voltage noise of the OP471. As RS rises above 1 kW, total noise increases and is dominated by resistor noise rather than by voltage or current noise of the OP471. When RS exceeds 20 kW, current noise of the OP471 becomes the ma ...
... and source resistance. For RS < 1 kW the total noise is dominated by the voltage noise of the OP471. As RS rises above 1 kW, total noise increases and is dominated by resistor noise rather than by voltage or current noise of the OP471. When RS exceeds 20 kW, current noise of the OP471 becomes the ma ...
EUP7903 数据手册DataSheet 下载
... offers high output accuracy, extremely low dropout voltage, low quiescent current and fast start-up time. The EUP7903 is designed to work with low-ESR ceramic capacitors, reducing the amount of the PCB area necessary for power applications. Only a 1uF ceramic output capacitor can make the device sta ...
... offers high output accuracy, extremely low dropout voltage, low quiescent current and fast start-up time. The EUP7903 is designed to work with low-ESR ceramic capacitors, reducing the amount of the PCB area necessary for power applications. Only a 1uF ceramic output capacitor can make the device sta ...
3.3 V, 3.2 Gbps, Limiting Amplifier ADN2891
... The threshold level can be set to anywhere from 3.5 mV p-p to 35 mV p-p, typical, and is set by a resistor connected between the THRADJ pin and VEE. See Figure 8 and Figure 9 for the LOS threshold vs. THRADJ. The ADN2891 LOS circuit has an electrical hysteresis greater than 2.5 dB to prevent chatter ...
... The threshold level can be set to anywhere from 3.5 mV p-p to 35 mV p-p, typical, and is set by a resistor connected between the THRADJ pin and VEE. See Figure 8 and Figure 9 for the LOS threshold vs. THRADJ. The ADN2891 LOS circuit has an electrical hysteresis greater than 2.5 dB to prevent chatter ...
LT2078/LT2079- Micropower, Dual and Quad, Single Supply, Precision Op Amps
... the LT2078/LT2079 was concentrated on reducing supply current without sacrificing other parameters. The offset voltage achieved is the lowest on any dual or quad nonchopper stabilized op amp––micropower or otherwise. Offset current, voltage and current noise, slew rate and gain bandwidth product are ...
... the LT2078/LT2079 was concentrated on reducing supply current without sacrificing other parameters. The offset voltage achieved is the lowest on any dual or quad nonchopper stabilized op amp––micropower or otherwise. Offset current, voltage and current noise, slew rate and gain bandwidth product are ...
ADA4420-6 数据手册DataSheet 下载
... is at least twice the value used for the single load (see Figure 20 and Figure 21). When driving two parallel 150 Ω loads (75 Ω effective load), the 3 dB bandwidth of the filters typically varies from that of the filters with a single 150 Ω load (see Figure 4). ...
... is at least twice the value used for the single load (see Figure 20 and Figure 21). When driving two parallel 150 Ω loads (75 Ω effective load), the 3 dB bandwidth of the filters typically varies from that of the filters with a single 150 Ω load (see Figure 4). ...
