TPS63030 数据资料 dataSheet 下载
... gets its feedback input from the FB pin. At adjustable output voltages a resistive voltage divider must be connected to that pin. At fixed output voltages FB must be connected to the output voltage to directly sense the voltage. Fixed output voltage versions use a trimmed internal resistive divider. ...
... gets its feedback input from the FB pin. At adjustable output voltages a resistive voltage divider must be connected to that pin. At fixed output voltages FB must be connected to the output voltage to directly sense the voltage. Fixed output voltage versions use a trimmed internal resistive divider. ...
LMK00105 Ultra-low Jitter LVCMOS Fanout Buffer/Level Translator
... Care should be taken to ensure the Vddo voltage does not exceed the Vdd voltage to prevent turning-on the internal ESD protection circuitry. DO NOT DISCONNECT OR GROUND ANY OF THE Vddo PINS because the Vddo pins are internally connected within an output bank. 7.3.2 Clock Input The LMK00105 has one d ...
... Care should be taken to ensure the Vddo voltage does not exceed the Vdd voltage to prevent turning-on the internal ESD protection circuitry. DO NOT DISCONNECT OR GROUND ANY OF THE Vddo PINS because the Vddo pins are internally connected within an output bank. 7.3.2 Clock Input The LMK00105 has one d ...
MAX16804 High-Voltage, 350mA LED Driver with Analog and PWM Dimming Control General Description
... The MAX16804 current regulator operates from a 5.5V to 40V input voltage range and delivers 35mA to 350mA to one or more strings of high-brightness LEDs (HB LEDs). The output current of the MAX16804 is set by using an external current-sense resistor in series with the LEDs. A dual-mode DIM pin and o ...
... The MAX16804 current regulator operates from a 5.5V to 40V input voltage range and delivers 35mA to 350mA to one or more strings of high-brightness LEDs (HB LEDs). The output current of the MAX16804 is set by using an external current-sense resistor in series with the LEDs. A dual-mode DIM pin and o ...
BQ24312 数据资料 dataSheet 下载
... protection against turning power off due to transient overvoltage spikes while still protecting the system. However, if the input voltage remains above VOVP for more than tBLANK(OVP), the internal FET is turned off, removing power from the circuit (see Figure 5). When the input voltage comes back to ...
... protection against turning power off due to transient overvoltage spikes while still protecting the system. However, if the input voltage remains above VOVP for more than tBLANK(OVP), the internal FET is turned off, removing power from the circuit (see Figure 5). When the input voltage comes back to ...
IDT2309 - Integrated Device Technology
... REF TO CLKA/CLKB RELAY vs. OUTPUT LOAD DIFFERENCE BETWEEN CLKOUT PIN AND CLKA/CLKB PINS ...
... REF TO CLKA/CLKB RELAY vs. OUTPUT LOAD DIFFERENCE BETWEEN CLKOUT PIN AND CLKA/CLKB PINS ...
LTC6403-1 - 200MHz, Low Noise, Low Power Fully Differential Input
... that the differential gain has not deviated from the mid supply VOCM case by more than 1%, and the common mode offset (VOSCM) has not deviated by more than ±10mV from the mid supply case. Note 8: Input CMRR is defined as the ratio of the change in the input common mode voltage at the pins +IN or –IN ...
... that the differential gain has not deviated from the mid supply VOCM case by more than 1%, and the common mode offset (VOSCM) has not deviated by more than ±10mV from the mid supply case. Note 8: Input CMRR is defined as the ratio of the change in the input common mode voltage at the pins +IN or –IN ...
TPS54331 数据资料 dataSheet 下载
... Maximum power dissipation may be limited by overcurrent protection Power rating at a specific ambient temperature TA should be determined with a junction temperature of 150°C. This is the point where distortion starts to substantially increase. Thermal management of the PCB should strive to keep the ...
... Maximum power dissipation may be limited by overcurrent protection Power rating at a specific ambient temperature TA should be determined with a junction temperature of 150°C. This is the point where distortion starts to substantially increase. Thermal management of the PCB should strive to keep the ...
Data Sheet ACPL-798J Optically Isolated Sigma-Delta Modulator with LVDS Interface Description
... signal power is the rms amplitude of the fundamental input signal. Noise plus distortion power is the rms sum of all non-fundamental signals up to half the sampling frequency (excluding DC). ...
... signal power is the rms amplitude of the fundamental input signal. Noise plus distortion power is the rms sum of all non-fundamental signals up to half the sampling frequency (excluding DC). ...
