EDC-1 - Duplomatic Oleodinamica
... o1: “I Min” current, expressed in milliampere. It sets the offset current to the solenoid, when the reference signal exceeds the limit of 0,1 V (or 0,1 mA). It is used to null the insensitiveness area of the valve (dead band). Default value = 0% Range = 0 ÷ 50% of Imax u1: “Ramp Up” increasing ramp ...
... o1: “I Min” current, expressed in milliampere. It sets the offset current to the solenoid, when the reference signal exceeds the limit of 0,1 V (or 0,1 mA). It is used to null the insensitiveness area of the valve (dead band). Default value = 0% Range = 0 ÷ 50% of Imax u1: “Ramp Up” increasing ramp ...
APXSERIES 2-CHANNEL 1500 WATT POWER AMPLIFIER
... 350 Watts at 8 ohms, 2 x 550 Watts at 4 ohms or 1500 Watts at 8 ohms in bridged mono mode. Level and clip indicators provide easy monitoring of performance levels. The APX1500 also contains low-noise cooling fans to maintain optimal temperature and prevent overheating and features a high-efficiency ...
... 350 Watts at 8 ohms, 2 x 550 Watts at 4 ohms or 1500 Watts at 8 ohms in bridged mono mode. Level and clip indicators provide easy monitoring of performance levels. The APX1500 also contains low-noise cooling fans to maintain optimal temperature and prevent overheating and features a high-efficiency ...
Quiz 4, EE 303, Spring 2002, Dr
... Vt 1.00 , and the internal voltage of the generator is . The magnitudes of both voltages given are in per-unit on bases consistent with the given synchronous reactance. The three-phase power base is 100MVA. Compute the real power out of the machine in (a) per-unit (24 pts) and (b) three-phase MW ...
... Vt 1.00 , and the internal voltage of the generator is . The magnitudes of both voltages given are in per-unit on bases consistent with the given synchronous reactance. The three-phase power base is 100MVA. Compute the real power out of the machine in (a) per-unit (24 pts) and (b) three-phase MW ...
Noise Equivalent Power (NEP) - Electro
... in a stereo when no music is playing. The noise spectrum has a relatively flat response, and the noise level changes with the square root of the frequency range; for example, if the frequency range doubles, the noise component increases by √2 (1.414). The optical input has to be large enough to over ...
... in a stereo when no music is playing. The noise spectrum has a relatively flat response, and the noise level changes with the square root of the frequency range; for example, if the frequency range doubles, the noise component increases by √2 (1.414). The optical input has to be large enough to over ...
FWJ-(20-30)A14F
... at power factor of 15% are given in the electrical characteristics. For other voltages, the clearing I2t is found by multiplying by correction factor, K , given as a function of applied working voltage, E g , (RMS). ...
... at power factor of 15% are given in the electrical characteristics. For other voltages, the clearing I2t is found by multiplying by correction factor, K , given as a function of applied working voltage, E g , (RMS). ...
Units and symbols for Modules 3 and 4
... Unfortunately, because the numbers can be very large or very small, many of the electrical units can be cumbersome for everyday use. For example, the voltage present at the antenna input of a VHF radio could be as little as 0.0000015 V. At the same time, the resistance present in an amplifier stage ...
... Unfortunately, because the numbers can be very large or very small, many of the electrical units can be cumbersome for everyday use. For example, the voltage present at the antenna input of a VHF radio could be as little as 0.0000015 V. At the same time, the resistance present in an amplifier stage ...
Lesson Plan
... 1. Record all data and calculations in the tables below or on a separate piece of paper. 2. Connect voltmeter in parallel to one of the resistors. 3. Connect ammeter in series adjacent to the resistor being measured. 4. Measure and record voltage and current for all three resistors (Do not exceed 12 ...
... 1. Record all data and calculations in the tables below or on a separate piece of paper. 2. Connect voltmeter in parallel to one of the resistors. 3. Connect ammeter in series adjacent to the resistor being measured. 4. Measure and record voltage and current for all three resistors (Do not exceed 12 ...