High Speed, ESD-Protected, Full-Duplex, ADM2490E i
... logic side of the interface. Therefore, the part has two main sections: a digital isolation section and a transceiver section (see Figure 21). The driver input signal, which is applied to the TxD pin and referenced to logic ground (GND1), is coupled across an isolation barrier to appear at the trans ...
... logic side of the interface. Therefore, the part has two main sections: a digital isolation section and a transceiver section (see Figure 21). The driver input signal, which is applied to the TxD pin and referenced to logic ground (GND1), is coupled across an isolation barrier to appear at the trans ...
AN58 - 5V to 3.3V Converters for Microprocessor Systems
... losses. In continuous operation (i.e., the inductor current does not go to zero), the duty cycle for a 5V to 3.3V switching regulator is 66%. This means that the switch is ON for 2/3 of each cycle and OFF for the remaining 1/3. Table 2 shows four switching regulators suitable for 5V to 3.3V conversi ...
... losses. In continuous operation (i.e., the inductor current does not go to zero), the duty cycle for a 5V to 3.3V switching regulator is 66%. This means that the switch is ON for 2/3 of each cycle and OFF for the remaining 1/3. Table 2 shows four switching regulators suitable for 5V to 3.3V conversi ...
Low-Voltage (1.2-V) High-Efficiency
... the automatic PFM mode, the controller goes to sleep when the inductor current goes discontinuous, and wakes up when the output voltage has fallen by 2%. (Please refer to the TPS43000 Data Sheet, TI Literature No. SLUS489 for more information.)The PFM mode is not used in this application. The conver ...
... the automatic PFM mode, the controller goes to sleep when the inductor current goes discontinuous, and wakes up when the output voltage has fallen by 2%. (Please refer to the TPS43000 Data Sheet, TI Literature No. SLUS489 for more information.)The PFM mode is not used in this application. The conver ...
High 5 Casino Game On Facebook List Of Casino Card Games
... Rj and Dj, measured on LeCroy LC684 Digital Storage Scope, directly into 50 ohm input, with Amherst M1 software. Per MJSQ spec (Methodologies for Jitter and Signal Quality specifications) ...
... Rj and Dj, measured on LeCroy LC684 Digital Storage Scope, directly into 50 ohm input, with Amherst M1 software. Per MJSQ spec (Methodologies for Jitter and Signal Quality specifications) ...
Activity 1.2.3 Electrical Circuits – Simulation
... Current between bulbs ______________A 12. Use the voltage (V) for the circuit in step 11 and the current (I) in step 12 to determine the resistance of the bulbs in series. Formula: Substitute values: Solve: Resistance = _______________Ω Creating a Parallel Circuit 13. Create the circuit shown below. ...
... Current between bulbs ______________A 12. Use the voltage (V) for the circuit in step 11 and the current (I) in step 12 to determine the resistance of the bulbs in series. Formula: Substitute values: Solve: Resistance = _______________Ω Creating a Parallel Circuit 13. Create the circuit shown below. ...
PDF
... Fig 5: gain amp across n-channel The transistors in shaded region M3X, M4X, M7X and M8X act as active load. This amplifier serves as replica amplifier without Vt. This amplifier has many advantages, i) the current through the single third input transistor will be reused in the new differential pair ...
... Fig 5: gain amp across n-channel The transistors in shaded region M3X, M4X, M7X and M8X act as active load. This amplifier serves as replica amplifier without Vt. This amplifier has many advantages, i) the current through the single third input transistor will be reused in the new differential pair ...
ECE-342 Lab 5: BJT Amplifier Sample Lab Report Don Hummels, Someone Else
... using the component values derived in Section 2 (RL = 10 kΩ, R1 = 8.33 kΩ, C = 47.1 µF) showed an amplifier gain of 45.7 dB, 0.3 dB lower than the desired gain of 46 dB. This 3% error in vout /vin is in part a result of neglecting the transistor output impedance ro in Section 2. For the collector cu ...
... using the component values derived in Section 2 (RL = 10 kΩ, R1 = 8.33 kΩ, C = 47.1 µF) showed an amplifier gain of 45.7 dB, 0.3 dB lower than the desired gain of 46 dB. This 3% error in vout /vin is in part a result of neglecting the transistor output impedance ro in Section 2. For the collector cu ...
EET 161 02
... goals will equip the learner with the ability to analyze series and parallel circuits, measure circuit values with electronic test instruments, construct AC and DC circuits and solve for unknown circuit variables. Basic concepts of energy, work, power, current and voltage are studied as well as Ohm’ ...
... goals will equip the learner with the ability to analyze series and parallel circuits, measure circuit values with electronic test instruments, construct AC and DC circuits and solve for unknown circuit variables. Basic concepts of energy, work, power, current and voltage are studied as well as Ohm’ ...
all-purpose dc regulated power supply
... 1. Input voltage: before switching on the power supply, please make sure that the local electrical supply is the same as the input voltage of this power supply. 2. Abnormal operation: Do not use your hands or other parts of the body to touch the fan-out of the DC500V to prevent being hurt A. The co ...
... 1. Input voltage: before switching on the power supply, please make sure that the local electrical supply is the same as the input voltage of this power supply. 2. Abnormal operation: Do not use your hands or other parts of the body to touch the fan-out of the DC500V to prevent being hurt A. The co ...
AD8215 数据手册DataSheet 下载
... THEORY OF OPERATION In typical applications, the AD8215 amplifies a small differential input voltage generated by the load current flowing through a shunt resistor. The AD8215 rejects high common-mode voltages (up to 65 V) and provides a ground-referenced, buffered output that interfaces with an ana ...
... THEORY OF OPERATION In typical applications, the AD8215 amplifies a small differential input voltage generated by the load current flowing through a shunt resistor. The AD8215 rejects high common-mode voltages (up to 65 V) and provides a ground-referenced, buffered output that interfaces with an ana ...