MAX3311/MAX3313 460kbps, 1µA Supply Current, RS-232-Compatible Transceivers in µMAX General Description
... into three state. The transmitter input does not have an internal pullup resistor. ...
... into three state. The transmitter input does not have an internal pullup resistor. ...
TLE2301 EXCALIBUR 3-STATE-OUTPUT WIDE-BANDWIDTH POWER OPERATIONAL AMPLIFIER
... VO(PP) – Maximum Peak-to-Peak Output Voltage – V ...
... VO(PP) – Maximum Peak-to-Peak Output Voltage – V ...
STL23NM50N
... or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. ...
... or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. ...
![Lesson 3: [llel+llel] Parallel Circuits](http://s1.studyres.com/store/data/014097890_1-3c36e45d3295a1e9d71d4d9b7f7bb136-300x300.png)
NCP1014STBUCGEVB Non-isolated Positive Output Buck AC/DC Converter Evaluation Board
... filtering capacitor, power stage with switcher and inductor, output ultrafast rectifier, output filtering capacitor, feedback loop with zener diode and optocoupler and indicating LED. The only component necessary for proper powering of the IC is the VCC capacitor. The IC is directly powered from the ...
... filtering capacitor, power stage with switcher and inductor, output ultrafast rectifier, output filtering capacitor, feedback loop with zener diode and optocoupler and indicating LED. The only component necessary for proper powering of the IC is the VCC capacitor. The IC is directly powered from the ...
i 1
... 3.3 Nodal Analysis with Voltage Source (2) A super-node is formed by enclosing a (dependent or independent) voltage source connected between two non-reference nodes and any elements connected in parallel with it. *Note: We analyze a circuit with super-nodes using the same three steps mentioned abov ...
... 3.3 Nodal Analysis with Voltage Source (2) A super-node is formed by enclosing a (dependent or independent) voltage source connected between two non-reference nodes and any elements connected in parallel with it. *Note: We analyze a circuit with super-nodes using the same three steps mentioned abov ...
` Delphi Series E48SP Eighth Brick Family DC/DC Power Modules
... The Delphi Series E48SP, 36~60V input, Eighth Brick, single output, isolated DC/DC converters are the latest offering from a world leader in power systems technology and manufacturing ― Delta Electronics, Inc. The E48SP product provides up to 240 watts of power in an industry standard footprint and ...
... The Delphi Series E48SP, 36~60V input, Eighth Brick, single output, isolated DC/DC converters are the latest offering from a world leader in power systems technology and manufacturing ― Delta Electronics, Inc. The E48SP product provides up to 240 watts of power in an industry standard footprint and ...
department of electrical and electronic engineering - suzon-aust
... coefficient k=1 and very large inductances. However, Spice does not allow a coupling coefficient of k=1. The ideal transformer can be simulated in Spice by making k close to one, and the inductors L1 and L2 very large, such that ωL1 and ωL2 is much larger than the resistors in series with the induct ...
... coefficient k=1 and very large inductances. However, Spice does not allow a coupling coefficient of k=1. The ideal transformer can be simulated in Spice by making k close to one, and the inductors L1 and L2 very large, such that ωL1 and ωL2 is much larger than the resistors in series with the induct ...
W. Rieutort-Louis, L. Huang, Y. Hu, J. Sanz-Robinson, S. Wagner, J.C. Sturm, N. Verma, "A figure of merit for oscillator-based thin-film circuits on plastic for high-performance signaling, energy harvesting and driving of actuation circuits, Device Research Conference (DRC), 10.1109/DRC.2012.6256980 pp. 117-118 University Park, PA JUN (2012).
... For even basic sensing and energy-harvesting functions, large-area systems-on-plastic require digital oscillators as a key circuit block [1]. However, their use to generate control signals, or drive actuator/energyharvesting circuits requires different performance metrics compared to conventional di ...
... For even basic sensing and energy-harvesting functions, large-area systems-on-plastic require digital oscillators as a key circuit block [1]. However, their use to generate control signals, or drive actuator/energyharvesting circuits requires different performance metrics compared to conventional di ...
MAX366/MAX367 Signal-Line Circuit Protectors _______________General Description ____________________________Features
... The MAX366 and MAX367 are multiple, two-terminal circuit protectors. Placed in series with signal lines, each two-terminal device guards sensitive circuit components against voltages near and beyond the normal supply voltages. These devices are used at interfaces where sensitive circuits are connect ...
... The MAX366 and MAX367 are multiple, two-terminal circuit protectors. Placed in series with signal lines, each two-terminal device guards sensitive circuit components against voltages near and beyond the normal supply voltages. These devices are used at interfaces where sensitive circuits are connect ...
Document
... 1. The AD536A computes the true root-mean-square level of a complex ac (or ac plus dc) input signal and gives an equivalent dc output level. The true rms value of a waveform is a more useful quantity than the average rectified value since it relates directly to the power of the signal. The rms value ...
... 1. The AD536A computes the true root-mean-square level of a complex ac (or ac plus dc) input signal and gives an equivalent dc output level. The true rms value of a waveform is a more useful quantity than the average rectified value since it relates directly to the power of the signal. The rms value ...
1. Features •
... mode (INT = 1) which, by default, ensures safety functions by activating or inhibiting external circuitry. Two CONTROL and STATUS 8-bit registers, are used respectively for setting operation to a given configuration, and for diagnosing the state of the circuit. The write and read modes of ports A an ...
... mode (INT = 1) which, by default, ensures safety functions by activating or inhibiting external circuitry. Two CONTROL and STATUS 8-bit registers, are used respectively for setting operation to a given configuration, and for diagnosing the state of the circuit. The write and read modes of ports A an ...