Project 1: Basic Testing Circuit
... The transistor shown has 3 connections. Connect the P and Q leads to all possible pairs, that is P to B and Q to E, then P to E and Q to B, and so for the each other possible pairing: B & C, C & B, C & E, E & C. ...
... The transistor shown has 3 connections. Connect the P and Q leads to all possible pairs, that is P to B and Q to E, then P to E and Q to B, and so for the each other possible pairing: B & C, C & B, C & E, E & C. ...
MAX4450/MAX4451 Ultra-Small, Low-Cost, 210MHz, Single-Supply Op Amps with Rail-to-Rail Outputs General Description
... The MAX4450/MAX4451 are optimized for AC performance. They are not designed to drive highly reactive loads, which decrease phase margin and may produce excessive ringing and oscillation. Figure 2 shows a circuit that eliminates this problem. Figure 3 is a graph of the optimal isolation resistor (RS) ...
... The MAX4450/MAX4451 are optimized for AC performance. They are not designed to drive highly reactive loads, which decrease phase margin and may produce excessive ringing and oscillation. Figure 2 shows a circuit that eliminates this problem. Figure 3 is a graph of the optimal isolation resistor (RS) ...
MAX9155 Low-Jitter, Low-Noise LVDS Repeater in an SC70 Package General Description
... The MAX9155’s tiny size makes it especially suitable for minimizing stub lengths in multidrop backplane applications. The SC70 package (half the size of a SOT23) allows the MAX9155 to be placed close to the connector, thereby minimizing stub lengths and reflections on the bus. The point-to-point con ...
... The MAX9155’s tiny size makes it especially suitable for minimizing stub lengths in multidrop backplane applications. The SC70 package (half the size of a SOT23) allows the MAX9155 to be placed close to the connector, thereby minimizing stub lengths and reflections on the bus. The point-to-point con ...
ST NE556
... 1.5kΩ resistor between two pins of the device. This is done for all couples of connected pin combinations while the other pins are floating. 3. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two pins of the device with no external series resis ...
... 1.5kΩ resistor between two pins of the device. This is done for all couples of connected pin combinations while the other pins are floating. 3. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two pins of the device with no external series resis ...
MONITOR AND CONTROL OF GREENHOUSE ENVIRONMENT
... Case#1: Dry condition- The probes are placed in the soil under dry conditions and are inserted up to a fair depth of the soil. As there is no conduction path between the two copper leads the sensor circuit remains open. The voltage output of the emitter in this case ranges from 0 to 0.5V Case#2: Opt ...
... Case#1: Dry condition- The probes are placed in the soil under dry conditions and are inserted up to a fair depth of the soil. As there is no conduction path between the two copper leads the sensor circuit remains open. The voltage output of the emitter in this case ranges from 0 to 0.5V Case#2: Opt ...
a Low Distortion Mixer AD831
... The AD831 is a low distortion, wide dynamic range, monolithic mixer for use in such applications as RF to IF down conversion in HF and VHF receivers, the second mixer in DMR base stations, direct-to-baseband conversion, quadrature modulation and demodulation, and doppler-shift detection in ultrasoun ...
... The AD831 is a low distortion, wide dynamic range, monolithic mixer for use in such applications as RF to IF down conversion in HF and VHF receivers, the second mixer in DMR base stations, direct-to-baseband conversion, quadrature modulation and demodulation, and doppler-shift detection in ultrasoun ...
Low voltage CMOS 16-bit D-type latch (3-state
... by two latch enable inputs (nLE) and two output enable inputs (OE). While the nLE input is held at a high level, the nQ outputs will follow the data input precisely. When the nLE is taken low, the nQ outputs will be in a normal logic state (high or low logic level) and while high level the outputs w ...
... by two latch enable inputs (nLE) and two output enable inputs (OE). While the nLE input is held at a high level, the nQ outputs will follow the data input precisely. When the nLE is taken low, the nQ outputs will be in a normal logic state (high or low logic level) and while high level the outputs w ...
Inventor - Hobbielektronika
... FIG. 1a shows the simplest form of a snubber circuit. Resistor 10 affects charging and discharging of capacitor 12 equally. This limits the amount of energy that can be stored to the amount which can be discharged during the shortest period ofthe operating cycle. FIG. 1b illustrates that this limita ...
... FIG. 1a shows the simplest form of a snubber circuit. Resistor 10 affects charging and discharging of capacitor 12 equally. This limits the amount of energy that can be stored to the amount which can be discharged during the shortest period ofthe operating cycle. FIG. 1b illustrates that this limita ...
