MAX17017 Quad-Output Controller for Low-Power Architecture General Description
... The main regulator can be configured as either a stepdown converter (for 2 to 4 Li+ cell applications) or as a step-up converter (for 1 Li+ cell applications). The internal switching regulators include 5V synchronous MOSFETs that can be powered directly from a single Li+ cell or from the main 3.3V/5 ...
... The main regulator can be configured as either a stepdown converter (for 2 to 4 Li+ cell applications) or as a step-up converter (for 1 Li+ cell applications). The internal switching regulators include 5V synchronous MOSFETs that can be powered directly from a single Li+ cell or from the main 3.3V/5 ...
LTC3406/LTC3406-1.5/LTC3406-1.8
... This formula has a maximum at VIN = 2VOUT, where IRMS = IOUT/2. This simple worst-case condition is commonly used for design because even significant deviations do not offer much relief. Note that the capacitor manufacturer’s ripple current ratings are often based on 2000 hours of life. This makes i ...
... This formula has a maximum at VIN = 2VOUT, where IRMS = IOUT/2. This simple worst-case condition is commonly used for design because even significant deviations do not offer much relief. Note that the capacitor manufacturer’s ripple current ratings are often based on 2000 hours of life. This makes i ...
MAX19793 1500MHz to 6000MHz Dual Analog Voltage Variable
... Note 1: Based on junction temperature TJ = TC + (BJC x VCC x ICC). This formula can be used when the temperature of the exposed pad is known while the device is soldered down to a PCB. See the Applications Information section for details. The junction temperature must not exceed +150NC. Note 2: TC ...
... Note 1: Based on junction temperature TJ = TC + (BJC x VCC x ICC). This formula can be used when the temperature of the exposed pad is known while the device is soldered down to a PCB. See the Applications Information section for details. The junction temperature must not exceed +150NC. Note 2: TC ...
4 Series Circuits
... Characteristics of Series Circuits ..................................................................................................... 5 Current in a Series Circuit ............................................................................................................ 5 Resistance in a Series ...
... Characteristics of Series Circuits ..................................................................................................... 5 Current in a Series Circuit ............................................................................................................ 5 Resistance in a Series ...
WCL488 Series 402828 Rev B1
... The copyright laws of the United States and other countries protect this material. It may not be reproduced, distributed, or altered in any fashion without the expressed written consent of TDITransistor Devices, Inc. ...
... The copyright laws of the United States and other countries protect this material. It may not be reproduced, distributed, or altered in any fashion without the expressed written consent of TDITransistor Devices, Inc. ...
Joystick Controllers
... Potentiometric sensing Designed to interface with an electronic controller, the long-life potentiometer tracks generate analogue outputs with switched reference signals that are proportional to the distance and direction over which the handle (or rocker) is moved. The analogue output can be factory ...
... Potentiometric sensing Designed to interface with an electronic controller, the long-life potentiometer tracks generate analogue outputs with switched reference signals that are proportional to the distance and direction over which the handle (or rocker) is moved. The analogue output can be factory ...
The LM3900 A New Current-Differencing Quad of Plus or Minus
... The LM3900 represents a departure from conventional amplifier designs. Instead of using a standard transistor differential amplifier at the input, the non-inverting input function has been achieved by making use of a ‘‘current-mirror’’ to ‘‘mirror’’ the non-inverting input current about ground and t ...
... The LM3900 represents a departure from conventional amplifier designs. Instead of using a standard transistor differential amplifier at the input, the non-inverting input function has been achieved by making use of a ‘‘current-mirror’’ to ‘‘mirror’’ the non-inverting input current about ground and t ...
Chapter 9 Zero-Voltage or Zero-Current Switchings
... antiparall diode has conducted – Voltage over switch is ≈ 0 – It is possible to use lossless snubbers, i.e. only snubber capacitor in the circuit as there is no discharge current when the switch is turned on Chapter 9 Resonant Converters ...
... antiparall diode has conducted – Voltage over switch is ≈ 0 – It is possible to use lossless snubbers, i.e. only snubber capacitor in the circuit as there is no discharge current when the switch is turned on Chapter 9 Resonant Converters ...
ES51969 - Cyrustek
... ES51969 provides detection of high-crest-factor (HCF) signal in ACV mode. ES51969 senses the signal and determines it as HCF if the Vpp is large enough. Once the signal is determined as HCF, ES51969 will jump up one measuring range regardless of current measurement value. It takes 60ms to jump one r ...
... ES51969 provides detection of high-crest-factor (HCF) signal in ACV mode. ES51969 senses the signal and determines it as HCF if the Vpp is large enough. Once the signal is determined as HCF, ES51969 will jump up one measuring range regardless of current measurement value. It takes 60ms to jump one r ...
Operational Amplifiers - Georgia Institute of Technology
... • Try to use single supply op-amps in order to minimize need for a 10V difference from power supply • Good low resistance, twisted, and shielded wire should be used when a sensor is located far away from the op-amp circuit. • Minimize current draw in sensor circuits to reduce thermal drift • Filter ...
... • Try to use single supply op-amps in order to minimize need for a 10V difference from power supply • Good low resistance, twisted, and shielded wire should be used when a sensor is located far away from the op-amp circuit. • Minimize current draw in sensor circuits to reduce thermal drift • Filter ...
MAX17017 - Part Number Search
... The main regulator can be configured as either a stepdown converter (for 2 to 4 Li+ cell applications) or as a step-up converter (for 1 Li+ cell applications). The internal switching regulators include 5V synchronous MOSFETs that can be powered directly from a single Li+ cell or from the main 3.3V/5 ...
... The main regulator can be configured as either a stepdown converter (for 2 to 4 Li+ cell applications) or as a step-up converter (for 1 Li+ cell applications). The internal switching regulators include 5V synchronous MOSFETs that can be powered directly from a single Li+ cell or from the main 3.3V/5 ...
Josephson voltage standard
A Josephson voltage standard is a complex system that uses a superconductive integrated circuit chip operating at 4 K to generate stable voltages that depend only on an applied frequency and fundamental constants. It is an intrinsic standard in the sense that it does not depend on any physical artifact. It is the most accurate method to generate or measure voltage and, by international agreement, is the basis for voltage standards around the World.