1. Introduction - About the journal
... Many active elements that are suitable for analog signal processing were introduced in [1]. Some of them have interesting features, which allow electronic control of their parameters. Therefore, these elements have also favorable features in applications. There are several common ways of electronic ...
... Many active elements that are suitable for analog signal processing were introduced in [1]. Some of them have interesting features, which allow electronic control of their parameters. Therefore, these elements have also favorable features in applications. There are several common ways of electronic ...
COOPER LIGHTING - SURE
... the DC circuit disconnects the lamp load from the battery should excessive wattage demands be made and automatically resets when the overload or short circuit is removed. This overload current protective feature eliminates the need for fuses or circuit breakers for the DC load. ...
... the DC circuit disconnects the lamp load from the battery should excessive wattage demands be made and automatically resets when the overload or short circuit is removed. This overload current protective feature eliminates the need for fuses or circuit breakers for the DC load. ...
UCC28060 数据资料 dataSheet 下载
... Gate drive on-time is proportional to VCOMP – 125 mV. The on-time proportionality factor, KT, is different in high and low ranges and also different in two-phase and single-phase modes. The on-time factor, KT, scales linearly with the value of RTSET. The minimum switching period is proportional to R ...
... Gate drive on-time is proportional to VCOMP – 125 mV. The on-time proportionality factor, KT, is different in high and low ranges and also different in two-phase and single-phase modes. The on-time factor, KT, scales linearly with the value of RTSET. The minimum switching period is proportional to R ...
Slides
... lots of vibrations from blower in SF6 tank. Can we find a different fan, or a variable speed drive so we can tune it away from the tank resonance, which is close to 30 Hz? output voltage droop when large currents turned on quickly. Can we measure the voltage versus rate of current increase somehow t ...
... lots of vibrations from blower in SF6 tank. Can we find a different fan, or a variable speed drive so we can tune it away from the tank resonance, which is close to 30 Hz? output voltage droop when large currents turned on quickly. Can we measure the voltage versus rate of current increase somehow t ...
MAX5951 12V/5V Input Buck PWM Controller General Description Features
... Analog Ground Connection. Solder the exposed pad to a large AGND plane. Connect AGND and PGND together at one point near the input bypass capacitor return terminal. Synchronization Output. SYNCOUT is a synchronization signal to drive the SYNCIN of a second MAX5950 or MAX5951, if used. Leave SYNCOUT ...
... Analog Ground Connection. Solder the exposed pad to a large AGND plane. Connect AGND and PGND together at one point near the input bypass capacitor return terminal. Synchronization Output. SYNCOUT is a synchronization signal to drive the SYNCIN of a second MAX5950 or MAX5951, if used. Leave SYNCOUT ...
AAT4601 数据资料DataSheet下载
... power switch designed for high-side load switching applications. This switch operates with inputs ranging from 2.7V to 5.5V, making it ideal for both 3V and 5V systems. An integrated current-limiting circuit protects the input supply against large changes in load current which could cause the supply ...
... power switch designed for high-side load switching applications. This switch operates with inputs ranging from 2.7V to 5.5V, making it ideal for both 3V and 5V systems. An integrated current-limiting circuit protects the input supply against large changes in load current which could cause the supply ...
Video Transcript - Rose
... We’re looking for the equivalent impedance between terminals G and H. The circuit, however, is given with all of its elements specified in terms of admittance. We’ll first convert those to impedance, then work the problem entirely in terms of impedance. Recall that impedance is the reciprocal of adm ...
... We’re looking for the equivalent impedance between terminals G and H. The circuit, however, is given with all of its elements specified in terms of admittance. We’ll first convert those to impedance, then work the problem entirely in terms of impedance. Recall that impedance is the reciprocal of adm ...
Monday - James K Beard
... Node voltages Currents through voltage sources Voltages across current sources ...
... Node voltages Currents through voltage sources Voltages across current sources ...
Electric Circuits and Electric Current
... What did we do in the lab yesterday? What did we measure? What was held constant? What shape did our graph take? What was our x variable? What was our y variable? What did the slope represent? What can we take away from this lab about the ...
... What did we do in the lab yesterday? What did we measure? What was held constant? What shape did our graph take? What was our x variable? What was our y variable? What did the slope represent? What can we take away from this lab about the ...
MT8870D(-1)
... The input arrangement of the MT8870D/MT8870D-1 provides a differential-input operational amplifier as well as a bias source (VRef) which is used to bias the inputs at mid-rail. Provision is made for connection of a feedback resistor to the op-amp output (GS) for adjustment of gain. In a single-ended ...
... The input arrangement of the MT8870D/MT8870D-1 provides a differential-input operational amplifier as well as a bias source (VRef) which is used to bias the inputs at mid-rail. Provision is made for connection of a feedback resistor to the op-amp output (GS) for adjustment of gain. In a single-ended ...
TS556
... Trigger terminal (pin 2) during the timing cycle discharges the external capacitor and causes the cycle to start over. The timing cycle now starts on the positive edge of the reset pulse. While the reset pulse is applied, the output is driven to the LOW state. When a negative trigger pulse is applie ...
... Trigger terminal (pin 2) during the timing cycle discharges the external capacitor and causes the cycle to start over. The timing cycle now starts on the positive edge of the reset pulse. While the reset pulse is applied, the output is driven to the LOW state. When a negative trigger pulse is applie ...
Operational amplifier
An operational amplifier (""op-amp"") is a DC-coupled high-gain electronic voltage amplifier with a differential input and, usually, a single-ended output. In this configuration, an op-amp produces an output potential (relative to circuit ground) that is typically hundreds of thousands of times larger than the potential difference between its input terminals.Operational amplifiers had their origins in analog computers, where they were used to do mathematical operations in many linear, non-linear and frequency-dependent circuits. The popularity of the op-amp as a building block in analog circuits is due to its versatility. Due to negative feedback, the characteristics of an op-amp circuit, its gain, input and output impedance, bandwidth etc. are determined by external components and have little dependence on temperature coefficients or manufacturing variations in the op-amp itself.Op-amps are among the most widely used electronic devices today, being used in a vast array of consumer, industrial, and scientific devices. Many standard IC op-amps cost only a few cents in moderate production volume; however some integrated or hybrid operational amplifiers with special performance specifications may cost over $100 US in small quantities. Op-amps may be packaged as components, or used as elements of more complex integrated circuits.The op-amp is one type of differential amplifier. Other types of differential amplifier include the fully differential amplifier (similar to the op-amp, but with two outputs), the instrumentation amplifier (usually built from three op-amps), the isolation amplifier (similar to the instrumentation amplifier, but with tolerance to common-mode voltages that would destroy an ordinary op-amp), and negative feedback amplifier (usually built from one or more op-amps and a resistive feedback network).