MCL488 Manual 403606 Rev A2
... The Dynaload is a precision instrument which simulates DC loads to test power supplies, generators, servo systems, batteries and similar DC sources. The MCL488 series provides up to ten load channels housed in a single chassis. Each load channel is fully independent, operating in one of four modes: ...
... The Dynaload is a precision instrument which simulates DC loads to test power supplies, generators, servo systems, batteries and similar DC sources. The MCL488 series provides up to ten load channels housed in a single chassis. Each load channel is fully independent, operating in one of four modes: ...
TRS3243 数据资料 dataSheet 下载
... only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to network GND ...
... only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to network GND ...
MXL1543 +5V Multiprotocol, 3Tx/3Rx, Software- Selectable Clock/Data Transceivers General Description
... Note 1: VDD and VEE absolute difference cannot exceed 13V. ...
... Note 1: VDD and VEE absolute difference cannot exceed 13V. ...
AN10777 LPC32x0 power supply design examples Rev. 01 — 22 January 2009
... HIGHCORE output pin is driven low after reset. A low indicates to an external power supply controller that nominal core voltage (1.2V) is needed. If software writes a 0 to the PWR_CTRL[1] bit, the HIGHCORE pin will drive high during STOP mode. The external power supply controller may then cause the ...
... HIGHCORE output pin is driven low after reset. A low indicates to an external power supply controller that nominal core voltage (1.2V) is needed. If software writes a 0 to the PWR_CTRL[1] bit, the HIGHCORE pin will drive high during STOP mode. The external power supply controller may then cause the ...
AD8319 数据手册DataSheet 下载
... The feedback loop through an RF amplifier is closed via VOUT, the output of which regulates the output of the amplifier to a magnitude corresponding to VSET. The AD8319 provides 0 V to (VPOS − 0.1 V) output capability at the VOUT pin, suitable for controller applications. As a measurement device, VO ...
... The feedback loop through an RF amplifier is closed via VOUT, the output of which regulates the output of the amplifier to a magnitude corresponding to VSET. The AD8319 provides 0 V to (VPOS − 0.1 V) output capability at the VOUT pin, suitable for controller applications. As a measurement device, VO ...
GE 40A Digital MegaDLynx : Non-Isolated DC-DC Power Modules Data Sheet
... First, there may be a need to further reduce the output ripple and noise of the module. Second, the dynamic response characteristics may need to be customized to a particular load step change. ...
... First, there may be a need to further reduce the output ripple and noise of the module. Second, the dynamic response characteristics may need to be customized to a particular load step change. ...
design and evaluation of a hybrid passive/active ripple filter
... supply voltages. These dc filter capacitors for satellite static power-converter applications have long been a problem. It is not only because of the bulky size required to provide the needed microfarads but also because of their relatively low reliability in the environment of outer space. Among th ...
... supply voltages. These dc filter capacitors for satellite static power-converter applications have long been a problem. It is not only because of the bulky size required to provide the needed microfarads but also because of their relatively low reliability in the environment of outer space. Among th ...
Continued… - Pcpolytechnic
... • The transformer is a static device (i.e. the one which does not contain any rotating or moving parts) which is used to transfer electrical energy from one ac circuit to another ac circuit, with increase or decrease in voltage/current but without any change in frequency. ...
... • The transformer is a static device (i.e. the one which does not contain any rotating or moving parts) which is used to transfer electrical energy from one ac circuit to another ac circuit, with increase or decrease in voltage/current but without any change in frequency. ...
Design of Ultra-Low-Power Analog-to-Digital Converters Dai Zhang
... register (SAR) ADC exhibits significantly high energy efficiency compared to other prevalent ADC architectures due to its good tradeoffs among power consumption, conversion accuracy, and design complexity. To design an energy-efficient SAR ADC, an understanding of its error sources as well as its po ...
... register (SAR) ADC exhibits significantly high energy efficiency compared to other prevalent ADC architectures due to its good tradeoffs among power consumption, conversion accuracy, and design complexity. To design an energy-efficient SAR ADC, an understanding of its error sources as well as its po ...
Solid State Relays Common Precautions
... however, use semiconductors, and semiconductors may commonly malfunction or fail. Short-circuit failures represent the main failure mode and can result in an inability to shut OFF the load. Therefore, for fail-safe operation of control circuits that use SSRs, do not use circuits that shut OFF the lo ...
... however, use semiconductors, and semiconductors may commonly malfunction or fail. Short-circuit failures represent the main failure mode and can result in an inability to shut OFF the load. Therefore, for fail-safe operation of control circuits that use SSRs, do not use circuits that shut OFF the lo ...
a 3 in Chip Scale Package ADG758/ADG759
... These switches are designed on an enhanced submicron process that provides low power dissipation yet gives high switching speed, very low ON resistance and leakage currents. ON resistance is in the region of a few ohms and is closely matched between switches and very flat over the full signal range. ...
... These switches are designed on an enhanced submicron process that provides low power dissipation yet gives high switching speed, very low ON resistance and leakage currents. ON resistance is in the region of a few ohms and is closely matched between switches and very flat over the full signal range. ...
WRL0001.tmp
... One interesting characteristic of an amplifier is that it is a unilateral device—it makes a big difference which end you use as the input! Most passive linear circuits (e.g., using only R, L and C) are reciprocal. With respect to a 2-port device, reciprocity means: Z 12 Z 21 ...
... One interesting characteristic of an amplifier is that it is a unilateral device—it makes a big difference which end you use as the input! Most passive linear circuits (e.g., using only R, L and C) are reciprocal. With respect to a 2-port device, reciprocity means: Z 12 Z 21 ...
Power MOSFET
A power MOSFET is a specific type of metal oxide semiconductor field-effect transistor (MOSFET) designed to handle significant power levels.Compared to the other power semiconductor devices, for example an insulated-gate bipolar transistor (IGBT) or a thyristor, its main advantages are high commutation speed and good efficiency at low voltages. It shares with the IGBT an isolated gate that makes it easy to drive. They can be subject to low gain, sometimes to degree that the gate voltage needs to be higher than the voltage under control.The design of power MOSFETs was made possible by the evolution of CMOS technology, developed for manufacturing integrated circuits in the late 1970s. The power MOSFET shares its operating principle with its low-power counterpart, the lateral MOSFET.The power MOSFET is the most widely used low-voltage (that is, less than 200 V) switch. It can be found in most power supplies, DC to DC converters, and low voltage motor controllers.