
assessment of dielectric properties of epoxy resin
... referred in earlier literature show^ that within one hour of moisturing time the values of loss factor and leakage current attain stabilization. Based on this the samples were conditioned in the humidity chamber for three hours, at each level of humidity. During this conditioning the voltages were m ...
... referred in earlier literature show^ that within one hour of moisturing time the values of loss factor and leakage current attain stabilization. Based on this the samples were conditioned in the humidity chamber for three hours, at each level of humidity. During this conditioning the voltages were m ...
MAX44265 Rail-to-Rail, 200kHz Op Amp with Shutdown in a Tiny, 6-Bump WLP
... Rail-to-Rail Inputs and Outputs The IC has a parallel-connected n- and p-channel differential input stage that allows an input common-mode voltage range that extends 100mV beyond the positive and negative supply rails, with excellent common-mode rejection. The IC is capable of driving the output to ...
... Rail-to-Rail Inputs and Outputs The IC has a parallel-connected n- and p-channel differential input stage that allows an input common-mode voltage range that extends 100mV beyond the positive and negative supply rails, with excellent common-mode rejection. The IC is capable of driving the output to ...
Hardware Error Rate Characterization with Below
... As a result, we can no longer power all transistors on chip; rather, we can power only a decreasing fraction of them. At the same time, the increasing demand for computational power comes at the cost of higher aggregate energy consumption. The computers’ insatiable appetite for energy has made IT in ...
... As a result, we can no longer power all transistors on chip; rather, we can power only a decreasing fraction of them. At the same time, the increasing demand for computational power comes at the cost of higher aggregate energy consumption. The computers’ insatiable appetite for energy has made IT in ...
MAX1816/MAX1994 Dual Step-Down Controllers Plus Linear- Regulator Controller for Notebook Computers General Description
... for notebook computer applications. BUCK1 is a CPU core regulator with dynamically adjustable output, ultrafast transient response, high DC accuracy, and high efficiency. BUCK2 is an adjustable step-down regulator for I/O and memory supplies. Both regulators employ Maxim’s proprietary Quick-PWM™ con ...
... for notebook computer applications. BUCK1 is a CPU core regulator with dynamically adjustable output, ultrafast transient response, high DC accuracy, and high efficiency. BUCK2 is an adjustable step-down regulator for I/O and memory supplies. Both regulators employ Maxim’s proprietary Quick-PWM™ con ...
DC Parameters: Input Offset Voltage (VIO)
... The cause of input offset voltage is well known—it is due to the inherent mismatch of the input transistors and components during fabrication of the silicon die, and stresses placed on the die during the packaging process (minor contribution). These effects collectively produce a mismatch of the bia ...
... The cause of input offset voltage is well known—it is due to the inherent mismatch of the input transistors and components during fabrication of the silicon die, and stresses placed on the die during the packaging process (minor contribution). These effects collectively produce a mismatch of the bia ...
Measurements - Crack IIT JEE
... (ii) naked eye cannot correctly estimate less than 0.5 mm For greater accuracy we use devices like vernier calipers and micrometer scales (screw gauge). LEAST COUNT ...
... (ii) naked eye cannot correctly estimate less than 0.5 mm For greater accuracy we use devices like vernier calipers and micrometer scales (screw gauge). LEAST COUNT ...
Sem1_2 _Basic
... together. For example if resistors R1 and R2 are connected in series their combined resistance, R, is given by: Combined resistance in series: R = R1 + R2 This can be extended for more resistors: R = R1 + R2 + R3 + R4 + ... ...
... together. For example if resistors R1 and R2 are connected in series their combined resistance, R, is given by: Combined resistance in series: R = R1 + R2 This can be extended for more resistors: R = R1 + R2 + R3 + R4 + ... ...
Smith Chart Calculations
... Quite often it is desirable to convert impedance information to admittance data—conductance and susceptance. Working with admittances greatly simplifies determining the resultant when two complex impedances are connected in parallel, as in stub matching. The conductance values may be added directly ...
... Quite often it is desirable to convert impedance information to admittance data—conductance and susceptance. Working with admittances greatly simplifies determining the resultant when two complex impedances are connected in parallel, as in stub matching. The conductance values may be added directly ...
Leakage Current Reduction in CMOS VLSI Circuits by Input Vector
... was important only in systems with long inactive periods (e.g., pagers and networks of sensors), it has become a critical design concern in any system in today’s designs. Unlike the dynamic power, which depends on the average number of switching transistors per clock cycle, the leakage power depends ...
... was important only in systems with long inactive periods (e.g., pagers and networks of sensors), it has become a critical design concern in any system in today’s designs. Unlike the dynamic power, which depends on the average number of switching transistors per clock cycle, the leakage power depends ...
555 - Faculty
... PIN 1 Ground--usually connected to ground. The voltage should be the most negative of any voltage appearing at the other pins. PIN 2 Trigger--level-sensitive point to 1/3 VCC. When the voltage at this pin is brought below 1/3 VCC the flip-flop is set causing pin 3 to produce a high state. Allowable ...
... PIN 1 Ground--usually connected to ground. The voltage should be the most negative of any voltage appearing at the other pins. PIN 2 Trigger--level-sensitive point to 1/3 VCC. When the voltage at this pin is brought below 1/3 VCC the flip-flop is set causing pin 3 to produce a high state. Allowable ...
EEI – resistance of Graphite: journal
... The accuracy of a value is very important and there are many sources of error that can affect this. The accuracy of a quantity is “an indication of how close a measurement is to the accepted value of the quantity being measured” (Greg Strahorn, Atomic Theory and Precision in Physics, 2014). Sources ...
... The accuracy of a value is very important and there are many sources of error that can affect this. The accuracy of a quantity is “an indication of how close a measurement is to the accepted value of the quantity being measured” (Greg Strahorn, Atomic Theory and Precision in Physics, 2014). Sources ...
Multimeter
A multimeter or a multitester, also known as a VOM (Volt-Ohm meter or Volt-Ohm-milliammeter ), is an electronic measuring instrument that combines several measurement functions in one unit. A typical multimeter would include basic features such as the ability to measure voltage, current, and resistance. Analog multimeters use a microammeter whose pointer moves over a scale calibrated for all the different measurements that can be made. Digital multimeters (DMM, DVOM) display the measured value in numerals, and may also display a bar of a length proportional to the quantity being measured. Digital multimeters are now far more common but analog multimeters are still preferable in some cases, for example when monitoring a rapidly varying value. A multimeter can be a hand-held device useful for basic fault finding and field service work, or a bench instrument which can measure to a very high degree of accuracy. They can be used to troubleshoot electrical problems in a wide array of industrial and household devices such as electronic equipment, motor controls, domestic appliances, power supplies, and wiring systems.Multimeters are available in a wide range of features and prices. Cheap multimeters can cost less than US$10, while laboratory-grade models with certified calibration can cost more than US$5,000.