Dup Dup - Bastl Instruments
... Double check the polarity of the ribbon cable and that it is not shifted in any direction. The red cable should be attached to the -12V rail, both on the module and on the bus board side! Although we put protection circuits in the device, we do not take any responsibility for damages caused by wrong ...
... Double check the polarity of the ribbon cable and that it is not shifted in any direction. The red cable should be attached to the -12V rail, both on the module and on the bus board side! Although we put protection circuits in the device, we do not take any responsibility for damages caused by wrong ...
Transmitter Architectures
... ο input data is first shaped (limit itβs spectral width) by a Gaussian filter in the time domain and then applied to the FM modulator ο the modulator take the digital data at input, and a Gaussian filter with a bandwidth of half of the data rate will produce the desired Gaussian spectrum in the freq ...
... ο input data is first shaped (limit itβs spectral width) by a Gaussian filter in the time domain and then applied to the FM modulator ο the modulator take the digital data at input, and a Gaussian filter with a bandwidth of half of the data rate will produce the desired Gaussian spectrum in the freq ...
Instruction Manual
... The gain setting need not provide a CT100 nominal output level of 1 Volt (Vo=1V). Gain can be adjusted so the CT100 output level matches the required input signal level of preamplifiers etc. Select only gain settings specified in table 3. Gain should not be set so the CT100 output level at OUT1 and ...
... The gain setting need not provide a CT100 nominal output level of 1 Volt (Vo=1V). Gain can be adjusted so the CT100 output level matches the required input signal level of preamplifiers etc. Select only gain settings specified in table 3. Gain should not be set so the CT100 output level at OUT1 and ...
2559 protected quad power drivers
... Over-current protection for each channel has been designed into these devices and is activated at approximately 1 A. It protects each output from short circuits with supply voltages up to 25 V. When an output current trip point is reached, that output stage is driven linearly resulting in a reduced ...
... Over-current protection for each channel has been designed into these devices and is activated at approximately 1 A. It protects each output from short circuits with supply voltages up to 25 V. When an output current trip point is reached, that output stage is driven linearly resulting in a reduced ...
Sep 2003 Low Voltage Amplifiers Give Choice of Accuracy or Speed
... offset voltage, lower input bias current, and higher DC gain than other devices with comparable bandwidth, which is critical in circuits having high input impedance, such as active filters, or in circuits having precision requirements, such as current sensing amplifiers. The LT1803 and LT6220 series ...
... offset voltage, lower input bias current, and higher DC gain than other devices with comparable bandwidth, which is critical in circuits having high input impedance, such as active filters, or in circuits having precision requirements, such as current sensing amplifiers. The LT1803 and LT6220 series ...
Linear Systems Offers Direct Alternative for Analog Devices MAT01
... LS312 available as bare die Please contact Micross for full package and die dimensions: Email: [email protected] Web: www.micross.com/distribution.aspx Information furnished by Linear Integrated Systems and Micross Components is believed to be accurate and reliable. However, no responsibili ...
... LS312 available as bare die Please contact Micross for full package and die dimensions: Email: [email protected] Web: www.micross.com/distribution.aspx Information furnished by Linear Integrated Systems and Micross Components is believed to be accurate and reliable. However, no responsibili ...
EZ2500 EZe test instruct rev5_EZ2500 EZe test instruct.qxd
... These instructions contain both information and warnings that are necessary for the safe operation and maintenance of the E-ZeTest EZ2500. It is recommended that you read the instructions carefully and ensure that the contents are fully understood. Failure to understand and to comply with the warnin ...
... These instructions contain both information and warnings that are necessary for the safe operation and maintenance of the E-ZeTest EZ2500. It is recommended that you read the instructions carefully and ensure that the contents are fully understood. Failure to understand and to comply with the warnin ...
lecture1429901112
... The RF input to be analyzed is applied to the input attenuator. After attenuating, the signal is fed to low pass filter. The low pass filter suppresses high frequency components and allows low frequency components to pass through it. The output of the low pass filter is given to the mixer, where th ...
... The RF input to be analyzed is applied to the input attenuator. After attenuating, the signal is fed to low pass filter. The low pass filter suppresses high frequency components and allows low frequency components to pass through it. The output of the low pass filter is given to the mixer, where th ...
With a basic understanding of schematics, a schematic can be used
... If the operator has power, but the open or close buttons do not work, check that the IR relay is getting line voltage at the two black wires on the coil of the relay. A common problem with mechanical motors is that the start switch can stick open, cutting off voltage to the IR relay. A typical sympt ...
... If the operator has power, but the open or close buttons do not work, check that the IR relay is getting line voltage at the two black wires on the coil of the relay. A common problem with mechanical motors is that the start switch can stick open, cutting off voltage to the IR relay. A typical sympt ...
Experiment #68 β Phase Locked Loops, the Basics
... that has a frequency controlled by an applied voltage. The frequency of the VCO without any control signal applied is called the freerunning frequency, f0. Depending on the circuit design, the VCO may be designed so Background Loop Components that f0 occurs with zero dc voltage input and The phase l ...
... that has a frequency controlled by an applied voltage. The frequency of the VCO without any control signal applied is called the freerunning frequency, f0. Depending on the circuit design, the VCO may be designed so Background Loop Components that f0 occurs with zero dc voltage input and The phase l ...
Chapter10
... the assumed state for each diode. Current must flow in the forward direction for diodes assumed to be on. Furthermore, the voltage across the diodes assumed to be off must be positive at the cathode (i.e., reverse bias). 4. If the results are consistent with the assumed states, the analysis is finis ...
... the assumed state for each diode. Current must flow in the forward direction for diodes assumed to be on. Furthermore, the voltage across the diodes assumed to be off must be positive at the cathode (i.e., reverse bias). 4. If the results are consistent with the assumed states, the analysis is finis ...
Quick Start Guide Universal Voltage Output Amplifier
... a) CONNECT LI-COR SENSOR TO UTA INPUT: Pass the LI-COR sensor cable through the included expander tubing. (There is a light lubricant inside the tubing.). Insert the combination through the UTA cable gland nearest the 2-terminal (blue/ brown) connection block. Loosen the gland nut if necessary. Conn ...
... a) CONNECT LI-COR SENSOR TO UTA INPUT: Pass the LI-COR sensor cable through the included expander tubing. (There is a light lubricant inside the tubing.). Insert the combination through the UTA cable gland nearest the 2-terminal (blue/ brown) connection block. Loosen the gland nut if necessary. Conn ...