AMC1203 数据资料 dataSheet 下载
... ±280mV Input Range with +5V Supply Internal 2.5V Reference Voltage: 1% Accuracy Gain Error: ±1% (AMC1203B) UL1577, IEC60747-5-2 (VDE0884, Rev. 2), and ...
... ±280mV Input Range with +5V Supply Internal 2.5V Reference Voltage: 1% Accuracy Gain Error: ±1% (AMC1203B) UL1577, IEC60747-5-2 (VDE0884, Rev. 2), and ...
Cascaded H-Bridge Multilevel Inverter Using PIC16F877A Controller
... applications. They typically synthesize the stair-case voltage waveform (from several dc sources) which has reduced harmonic content. In this work hardware model of five level single phase cascade H-bridge multilevel inverter has been developed using MOSFET switches. The gating pulses are given to M ...
... applications. They typically synthesize the stair-case voltage waveform (from several dc sources) which has reduced harmonic content. In this work hardware model of five level single phase cascade H-bridge multilevel inverter has been developed using MOSFET switches. The gating pulses are given to M ...
ESP8266 System Description
... Espressif’s ESP8266EX delivers a highly integrated Wi-Fi SoC solution to meet the continuous demand for efficient power usage, compact design and reliable performance in the industry. With its complete and self-contained Wi-Fi networking capabilities, ESP8266EX can perform either as a standalone app ...
... Espressif’s ESP8266EX delivers a highly integrated Wi-Fi SoC solution to meet the continuous demand for efficient power usage, compact design and reliable performance in the industry. With its complete and self-contained Wi-Fi networking capabilities, ESP8266EX can perform either as a standalone app ...
PAM8403 Description Pin Assignments
... terminal. For filtering lower frequency noise signals, a large capacitor of 20μF (ceramic) or greater is recommended, placing it near the audio power amplifier. ...
... terminal. For filtering lower frequency noise signals, a large capacitor of 20μF (ceramic) or greater is recommended, placing it near the audio power amplifier. ...
AS1363
... If pin EN is connected to GND the AS1363 is disabled. In shutdown mode all internal circuits are turned off, reducing supply current to 30nA typical. For normal operation pin EN must be connected to IN. During shutdown, POK is low. ...
... If pin EN is connected to GND the AS1363 is disabled. In shutdown mode all internal circuits are turned off, reducing supply current to 30nA typical. For normal operation pin EN must be connected to IN. During shutdown, POK is low. ...
LMP8645/LMP8645HV Precision High Voltage
... Operating from a supply range of 2.7 V to 12 V, the LMP8645 accepts input signals with a common-mode voltage range of –2 V to 42 V, while the LMP8645HV accepts input signals with a common-mode voltage range of –2 V to 76 V. The LMP8645 and LMP8645HV have adjustable gain for applications where supply ...
... Operating from a supply range of 2.7 V to 12 V, the LMP8645 accepts input signals with a common-mode voltage range of –2 V to 42 V, while the LMP8645HV accepts input signals with a common-mode voltage range of –2 V to 76 V. The LMP8645 and LMP8645HV have adjustable gain for applications where supply ...
DS1340 I C RTC with Trickle Charger 2
... The DS1340 operates as a slave device on the serial bus. Access is obtained by implementing a START condition and providing a device identification code followed by data. Subsequent registers can be accessed sequentially until a STOP condition is executed. The device is fully accessible and data can ...
... The DS1340 operates as a slave device on the serial bus. Access is obtained by implementing a START condition and providing a device identification code followed by data. Subsequent registers can be accessed sequentially until a STOP condition is executed. The device is fully accessible and data can ...
AN82 - Understanding and Applying Voltage
... be adjusted several percent above or below the intended operating point. If load current steps must be handled, transient response is important. Transient response varies widely from reference to reference and comprises three distinct qualities: turn-on characteristics, small-signal output impedance ...
... be adjusted several percent above or below the intended operating point. If load current steps must be handled, transient response is important. Transient response varies widely from reference to reference and comprises three distinct qualities: turn-on characteristics, small-signal output impedance ...
BDTIC C C M - P F C
... the voltage at the FREQ pin is higher than 2.5V. The synchronization means two points. Firstly, the PFC switching frequency is tracking the external pulse signal frequency. Secondly, the falling edge of the PFC signal is triggered by the rising edge of the external pulse signal. Figure 5 shows the b ...
... the voltage at the FREQ pin is higher than 2.5V. The synchronization means two points. Firstly, the PFC switching frequency is tracking the external pulse signal frequency. Secondly, the falling edge of the PFC signal is triggered by the rising edge of the external pulse signal. Figure 5 shows the b ...
AIC1533
... 0V proportionally. As VFBN decreases to 10% of VREF, Q7 turns off and Cp starts being charged from 5µA current source (referring to BLOCK DIAGRAM). The charging time of CP, defined as T2, can be calculated as ...
... 0V proportionally. As VFBN decreases to 10% of VREF, Q7 turns off and Cp starts being charged from 5µA current source (referring to BLOCK DIAGRAM). The charging time of CP, defined as T2, can be calculated as ...
ELTR 125 (Semiconductors 2)
... The purpose of the potentiometer is to provide an adjustable DC bias voltage for the transistor, so it may be operated in Class-A mode. After some adjustment of this potentiometer, the student is able to obtain good amplification from the transistor (signal generators and oscilloscopes have been omi ...
... The purpose of the potentiometer is to provide an adjustable DC bias voltage for the transistor, so it may be operated in Class-A mode. After some adjustment of this potentiometer, the student is able to obtain good amplification from the transistor (signal generators and oscilloscopes have been omi ...
Presentation PPT File - RFIC Group @ Fudan University
... synthesizer such as DVB-T • Loop bandwidth changes greatly during a wide frequency range • Wideband VCO needs AFC to select the subband automatically • Low phase noise and low phase error are required in the receiver ...
... synthesizer such as DVB-T • Loop bandwidth changes greatly during a wide frequency range • Wideband VCO needs AFC to select the subband automatically • Low phase noise and low phase error are required in the receiver ...
lec6
... is completely charged, and the voltage is practically constant. Then and thereafter, dv/dt0. All the current from the source goes through the resistor, and the capacitor behaves as an open circuit, that is ...
... is completely charged, and the voltage is practically constant. Then and thereafter, dv/dt0. All the current from the source goes through the resistor, and the capacitor behaves as an open circuit, that is ...
lec6
... is completely charged, and the voltage is practically constant. Then and thereafter, dv/dt0. All the current from the source goes through the resistor, and the capacitor behaves as an open circuit, that is ...
... is completely charged, and the voltage is practically constant. Then and thereafter, dv/dt0. All the current from the source goes through the resistor, and the capacitor behaves as an open circuit, that is ...
