Download part 3 - execution - AES Precast Company, Inc.

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Structural integrity and failure wikipedia , lookup

Transcript
PRE-ASSEMBLED PRECAST CONCRETE BUILDING
PART 1 - GENERAL
1.01 SUMMARY
Building to be delivered and placed on owner's prepared foundation in accordance with manufacture's
recommendations (PART 3). Precast building to be manufactured by AES PRECAST CO, INC, 3851
17th Street, Northport, AL 35476 (1-800-342-3274), or approved equal. Building to be provided by
manufacturer with all necessary openings as specified by contractor in conformance with
manufacturer's structural requirements.
1.02 QUALITY ASSURANCE
A. ACI-318-2002, "Building Code Requirements for Reinforced Concrete". Concrete Reinforcing
Institute, "Manual of Standard Practice".
B. ANSI/ASCE-7-02 "Building Code Requirements for Minimum Design Loads in Buildings and
Other Structures".
C. Florida Building Code – 2004 / Current FL DCA Approval
D. UL-752 Test Method Level Four (4) for Bullet Resistance certified by an Independent Structural
Engineer.
E. Concrete Reinforcing Institute, "Manual of Standard Practice".
F. Building fabricator must have a minimum of 5-years experience manufacturing and setting
transportable precast concrete buildings.
G. PCI Design Handbook – 6th Edition.
H. International Building Code – 2006.
I.
National Electrical Code – 2005.
J.
Manual of Steel Construction – LRFD AISC – 3rd Edition.
K. Manual of Steel Construction – ASD AISC – 9th Edition.
L. Manufacturer to Have at Least 5 Years of Experience.
M. Manufacturer to Provide at Least 5 References of Similar Scope.
N. Manufacturer to be a GSA Vendor.
1.03 DIMENSIONS & DESIGN LOADS
A. Walls are 3” (plus 3” interior finish if applicable) Thick; Floor is 6” Thick; Roof is 4” @ edge and
6” @ center, giving a 2” slope from center to edge.
B. Design Loads:
1.
Standard Seismic Load Performance Category 'C', Exposure Group III
2.
Standard Live Roof Load - 60 PSF
3.
Standard Floor Load - 250 PSF
4.
Standard Wind Loading - 140 MPH
C. Roof: (Flat) Roof panel shall slope 2" from center to sides. (Gable) Roof panel shall have a 4/12
slope. The roof shall extend a minimum of 2 1/2" beyond the wall panel on each side.
D. Roof, floor and wall panels single component monolithic panels. No roof, floor, or vertical wall
joints will be allowed, except at corners. Wall panels shall set on top of floor panel.
PART 2 - PRODUCTS
2.01 MATERIALS
A. Concrete: Steel-reinforced, polypropylene fiber reinforced, 5000 PSI minimum 28-day compressive
strength, air-entrained (ASTM C260).
B. Reinforcing Steel: ASTM A615, grade 60 unless otherwise indicated.
C. Reinforcing Fiber: Polypropylene fiber, Fibermesh @ 1.5 pounds per cubic yard.
D. Caulking: All joints between panels shall be caulked on the exterior and interior surface of the
joints. Caulking shall be SIKAFLEX-1A elastic sealant or equal.
E. Panel Connections: All panels shall be securely welded together with 1/4" thick steel brackets.
Steel is to be of structural quality, hot-rolled carbon complying with ASTM A283, Grade C. Castin anchors used for panel connections to be Dayton-Superior #F-63, or equal.
2.03 FINISHES
A. Interior of Building: (Choose 1) Walls and Ceiling to be painted, white. – Or- Walls and Ceiling to
be finished with R-18 Insulation with FRP Laminated ¾” Wheatboard, White. (Choose 1) Floor to
be finished with Vinyl Tile Flooring with Rubber Base Molding. –Or- Floor to be smooth,
unfinished. –Or- Floor to be smooth with anti-slip coating.
B. Exterior of Building: (Choose 1) Exposed Aggregate with Clear Coat. –Or- Simulated Split-Faced
Block / Brick / Vertical Plank / Horizontal Plank / Fluted Fin / Fractured Fin / Smooth / Stucco /
Ashlar Stone, Painted (Choice of Color(s))
C. Roof: (Choose 1) Standard roof to have smooth trowel finish, sealed with Hydro-Stop liquid
applied roofing system, white. –Or- Concrete Gable Roof with 4/12 pitch, Simulated Raised Seam
Metal / Cedar Shake, Painted (Choice of Color(s))
PART 3 - EXECUTION
3.01 SITE PREPARATION (Standard Pre-assembled Building)
A. AES Precast Building shall bear fully on a crushed stone base that is at least one foot larger than the
length and width of building.
B. Stone shall be a minimum of 4" thick or down to firm subgrade. Substrate below stone must have a
vertical soil capacity of 1,500 pounds per square foot. Stone shall be 3/8" or smaller and placed
within a perimeter form with flat and level top edge for screeding, such as concrete curbing, railroad
ties, or compacted earth.
C. Stone must be screeded to level within 1/4" in both directions. Forming material shall remain around
stone after the building is set.
D. The crushed stone base shall be kept within the confines of the soil or perimeter form. Do not allow
the stone base to become unconfined so that it may wash, erode or otherwise be undermined.
OR
3.02 SITE PREPARATION (Standard, Floorless Pump House, and Multi-Part Expanded Pre-assembled
Building) *
A. AES Precast Building shall bear fully on pavement or concrete slab that has length and width
equal to or greater than that of the floor of the building.
B. Substrate below pavement or slab must have a vertical soil capacity of 1,500 pounds per square
foot, and covered with 6 mil vapor barrier. Concrete slab should be poured 4” thick with 12”
turndown footing on all sides, using 3,000 PSI concrete, and reinforced with W4 x W4 – 4” x 4”
wire mesh.
C. Pad or slab should be level to 1/8” in all directions.
D. Provide positive drainage for the pad or slab as required.
* Site Preparation 3.02 must be followed for all Pump House and Expanded Pre-assembled Buildings.
3.03 ACCESS
A. Purchaser must provide level unobstructed area large enough for crane and tractor trailer to park
adjacent to pad. Crane must be able to place outriggers within 3'-0" of edge of pad and truck and
crane must be able to get side-by-side under their own power. No overhead lines may be within 75'
radius of center of pad. Firm roadbed with turns that allow 65' lowbed tractor and trailer must be
provided directly to site. No building shall be placed closer than 2'-0" to an existing structure.
©AES Precast Co, Inc. 2007