Download ppt - 0-2u.com

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Audio power wikipedia , lookup

Rectifier wikipedia , lookup

Stray voltage wikipedia , lookup

Power over Ethernet wikipedia , lookup

Spectral density wikipedia , lookup

Electric power system wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Power inverter wikipedia , lookup

Geophysical MASINT wikipedia , lookup

Three-phase electric power wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Islanding wikipedia , lookup

History of electric power transmission wikipedia , lookup

Electric motor wikipedia , lookup

Amtrak's 25 Hz traction power system wikipedia , lookup

Power MOSFET wikipedia , lookup

Power engineering wikipedia , lookup

Buck converter wikipedia , lookup

AC motor wikipedia , lookup

Alternating current wikipedia , lookup

Brushless DC electric motor wikipedia , lookup

Induction motor wikipedia , lookup

Metadyne wikipedia , lookup

Electrification wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Rectiverter wikipedia , lookup

Brushed DC electric motor wikipedia , lookup

Voltage optimisation wikipedia , lookup

Mains electricity wikipedia , lookup

Stepper motor wikipedia , lookup

Opto-isolator wikipedia , lookup

Variable-frequency drive wikipedia , lookup

Pulse-width modulation wikipedia , lookup

Transcript
SENIOR DESIGN
10/16
Pulse Width Modulation (PWM)
PWM is a way of digitally encoding analog signal levels.
Through the use of high-resolution counters, the duty cycle of a
square wave is modulated to encode a specific analog signal
level. The PWM signal is still digital because, at any given
instant of time, the full DC supply is either fully on or fully
off. The voltage or current source is supplied to the analog load
by means of a repeating series of on and off pulses. The on-time
is the time during which the DC supply is applied to the load,
and the off-time is the period during which that supply is
switched off. Given a sufficient bandwidth, any analog value can
be encoded with PWM.
Pulse Width Modulation (PWM)
Three different PWM signals. Figure 1a shows a PWM output at a 10% duty cycle.
That is, the signal is on for 10% of the period and off the other 90%.
Figures 1b and 1c show PWM outputs at 50% and 90% duty cycles, respectively.
These three PWM outputs encode three different analog signal values,
at 10%, 50%, and 90% of the full strength.
If, for example, the supply is 9V and the duty cycle is 10%, a 0.9V analog signal results.
Motors
Relays and Solenoids
MOTORS DC
DC MOTOR
BRUSHES
COMMUTATOR
MOTORS servo
Hobby Servo:
Built in Encoder -- Built in Servo Controller
+V, GND, Signal
Give the signal line a PWM value. (like PWM)
ATT: Pulse Width DEFINES POSITION, NOT SPEED
Pulse Width Signal created by Built Servo Controller.
[the above is true for hobby servos. It allows for cheap
Motors. Industrial servos, use different control
Techniques….]
MOTORS Stepper
Stepper Motor
[Electro-Magnets]
RELAYS
Microcontroller->Transistor->Solenoid
RELAYS
RELAYS solid state
Solid State Relays (SSR)
DC Solid State: opto-isolation, very fast (PWM), very low power, drive directly from
Microcontroller.
AC Solid State: same as above, may not be able to switch faster than the AC
Signal frequency. (used in light dimmers)
RELAYS vs. Transistor Switch
Mechanical Relay: cheap, makes little noise, visible
Mechanical motion.
Solid State Relay: opto-isolation, very fast (PWM),
very low power, drive directly from microcontroller.
Transistor Switch: very cheap, small, fast.
SENSORS
RESISTIVE SENSORS:
CAPACITIVE:
(change resistance)
(change capacitance)
“Photocell”
“Bend Sensors”
“CO sensor”
“Condenser microphones”
“Touch Sensors”
PIEZO ELECTRIC PYRO ELECTRIC SONARS
SENSORS
PIEZO ELECTRIC:
Create voltage when bent / when voltage across
they bend… .
some capacitive sensors have
PYRO ELECTRIC
digital-out built in.
Warps when exposed to heat. => change capacitance
(“Motion Infrared Sensors”)
SENSORS
SONARS
Emit sound and record time it takes for sound waves to return.
(reflection, angle, complications…)
PHOTOTRANSISTOR
Light controlled switches
(base current created with photons)
SENSORS
INFRARED REFLECTION SENSORS
Transmitter / Receiver in one package or two.
(record reflection time, similar to sonars; can be used as collision
detection sensors or data link.)
IR OPTICAL SWITCH
IR LED + PHOTOTRANSISTOR
SENSORS
BARCODES, RFID, ACCELEROMETERS, THERMIST
HUMIDITY, SENSORS, GYROSCOPES (how fast you
turning)… .
H-Bridge and Power
H-Bridge and Power
C Motor Control with a TIP120 TransistorThis example assumes you're using a DC motor that runs
on low voltage DC, in the 5-15V range. Connect leads to Its terminals, and run if from a benchtop power
supply if you have one. Try changing the voltage on it, and seeing what effect it has. Don't go over the
motor's rated voltage. Connect a switch in series with the motor and use it to turn on the motor.
Connect the base of a TIP120 transistor to one pin of your microcontroller.
Note the second power supply. Most motors take a great deal more current than a microprocessor
, and need their own supply. The example below uses a 9V battery as a separate power source.
Whatever motor you use, make sure the power source is compatible (i.e. don't use a 9V battery f
or a 3V motor!). Although the example shown is on a BX-24, you can use it with any microcontroller.
Just connect the 1K resistor to the output pin of your microcontroller.
H-Bridge and Power
This circuit drives small DC motors up to about 100 watts or
5 amps or 40 volts, whichever comes first. Using bigger parts
could make it more powerful. Using a real H-bridge IC makes sense for
this size of motor, but hobbyists love to do it themselves, and I thought
it was about time to show a tested
H-bridge motor driver that didn't use exotic parts.
http://www.allegromicro.com/
H-Bridge and Power
H-Bridge and Power
H-Bridge and Power
H-Bridge and Power
PWM MOTOR DRIVE
Translating Rotational
Movement
WORM GEAR
Translating Rotational
Movement
Linkages
Translating Rotational
Movement
Belt Drive
Translating Rotational
Movement
Mechanical Movements
Robotic Mechanisms
http://www.beatrizdacosta.net/projects.html
Motor Positioning
Motor Positioning
OUR ASSIGNMENTS
• Light to vary motor speed.
• Heat to set off siren.
Light to Speed
Mapping data… AND redefine your baseline each time...
Heat to Sound
Define Threshold… AND redefine your baseline each time..
ANALOG VOLTAGES on ARDUINO
• analogRead: -- reads an analog voltage
at any of the ADC pins (you have 6).
• analogWrite: -- writes a PWM pulse to
the PWM enabled digital pins (you have
3).
• Sensor “Calibration”
READING/WRITING
• Global Issues, question 1&2. 2 pages
max.
• Due: October 30th, beginning of
Lecture.
• No lecture next week.