Download Shuttle XPC Accessory PC45G (250W Power Supply)

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Rectifier wikipedia , lookup

Three-phase electric power wikipedia , lookup

Decibel wikipedia , lookup

Standby power wikipedia , lookup

Power factor wikipedia , lookup

Buck converter wikipedia , lookup

Wireless power transfer wikipedia , lookup

History of electric power transmission wikipedia , lookup

Phone connector (audio) wikipedia , lookup

Alternating current wikipedia , lookup

Electric power system wikipedia , lookup

Gender of connectors and fasteners wikipedia , lookup

Life-cycle greenhouse-gas emissions of energy sources wikipedia , lookup

Audio power wikipedia , lookup

Metadyne wikipedia , lookup

Voltage optimisation wikipedia , lookup

Amtrak's 25 Hz traction power system wikipedia , lookup

Power over Ethernet wikipedia , lookup

Power engineering wikipedia , lookup

Electrification wikipedia , lookup

Mains electricity wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Power supply unit (computer) wikipedia , lookup

Power supply wikipedia , lookup

AC adapter wikipedia , lookup

Transcript
Product Specifications
XPC Accessory
250 Watt 80Plus Bronze Power Supply
PC45G
The Shuttle XPC Accessory PC45G is an internal AC to DC power
supply unit (PSU) meant as a replacement device for certain
Shuttle products. It provides a maximum output wattage of 250
Watt. Its 80 PLUS® Bronze and Energy Star V5.0 compliance helps
save on energy costs as compared to previous power supply
models such as PC40. In addition, its double ball-bearing fan has
a longer lifetime and faces to the inside which reduces the noise
level to a minimum.
Input






Input Voltage: 90~264 V AC (auto-adjust)
Input Current: max. 3.0~1.5 A
Frequency: 47~63 Hz
Active PFC (Power Factor Correction)
Over voltage protection (OVP)
Connector: cold-device plug, 3-pin with PE




Total combined output (3.3/5/12V): 250W
for 3.3V/5V: 100W, for 12V: 216W
Max. Current: +3.3V (18A), +5V (18A), +12V
(17A), -12V (0.3A), +5Vsb (2A)
Hold up time: >17ms (full load, 115V AC)
+12V Rise time: <20ms (full load)
Protection: OTP/OPP/UVP/OCP/SCP/OVP





1x
1x
3x
2x
1x

Output
Connectors
Energy
efficiency
Compliance
Other
Compatibility
Package
contents
ATX
24 pin
main mainboard connector (24-pin ATX)
mainboard 12V AUX (4-pin ATX)
Serial ATA connectors (15-pin SATA)
Molex connectors (4-pin IDE/PATA)
Floppy connector (4-pin FDD)
ATX
12V
4 pin
80PLUS Bronze compliant: the PSU provides at
least 82/85/82% efficiency at 20/50/100% load.
Aligns to the power supply requirements of
Energy Star V5.0
1x
Floppy

CE, CB, WEEE, ErP, RoHS




Dimension: 150 x 80 x 40 mm (DWH)
Flex ATX form factor
40 mm double ball-bearing fan
PSU manufacturer: Fortron Source Techn.
Product ID of manufacturer: 9PA250CX03
2x
Molex

Compatible with XPC chassis of the G, G2,
G5, G6 series and the XPC model ST61G4
NOT compatible with SD11G5, SS56L, SK83G,
SN85G4, SN95G5 and ST20G5.
3x
S-ATA



Internal AC power supply with angle holder
Quick guide
Order number: POC-PC45G01
Page 1 | 22 June 2015
www.shuttle.com
Shu t tl e Computer Han dels GmbH
Fritz- Strassmann-S t r. 5
25337 Elmshorn | Germany
Tel. +49 (0) 4121-47 68 60
Fax +49 (0) 4121-47 69 00
[email protected]
© 2014 by Shuttle Computer Handels GmbH (Germany). All information subject to change without notice. Pictures for illustration purposes only.
Feature Highlights
Product Specifications
Easy installation of PC45G
Caution:
Do not attempt to open or service this device. Changes or modifications done to this product not approved by
the manufacturer will void warranty and violate CE approval. In case you haven't got necessary technical
knowledge how to install the device, please consult an expert or have a specialist company install it for you.
Installing the new power supply unit
1. Please fit the power supply into the chassis with the angle holder hooked in as shown in the picture.
2. Please affix the power supply on the rear side of the chassis using three screws (6-32 UNC x 5 mm).
3. Now start re-connecting the components to the power supply unit. Never force a connector into a
socket, as this may result in damage of the power supply unit and possible other hardware
components which is not covered by the warranty.
4. Notice: This power supply has a 24-pin connector for the mainboard. The Shuttle XPCs compatible
with this power supply however come with a 20-pin connector so that 4 pins will stick out then (see
picture).
5. Check all cable connections and make sure all components have been properly connected. Proceed
to plug the power cord into the power supply and connect the computer to the mains. If the computer
now boots correctly, any components are correctly connected and the installation process is
complete.
Images are for illustration purpose only.
Page 2 | 22 June 2015
www.shuttle.com
Shu t tl e Computer Han dels GmbH
Fritz- Strassmann-S t r. 5
25337 Elmshorn | Germany
Tel. +49 (0) 4121-47 68 60
Fax +49 (0) 4121-47 69 00
[email protected]
© 2014 by Shuttle Computer Handels GmbH (Germany). All information subject to change without notice. Pictures for illustration purposes only.
Removing the old power supply unit
1. Unplug the computer from the mains.
2. Open the computer.
3. Disconnect all connections between the old power supply unit and the various components such as
the mainboard, the hard drive and graphics card, etc.
4. Unscrew the screws that are used to secure the power supply unit to the back of the computer and
carefully remove the power supply unit.