Download Windows 3.1 Setup for

Data Residence Hall
Windows NT 4 Setup
Compiled by Academic Computing Services
1997
Note: You will need to fill out a maintenance request (located in the repair request drop box at or
near the front desk in each residence hall) to have the data port in your room turned on
(activated) before attempting this setup.
Should you have any trouble please contact your residence hall’s student data connection
advisor(s).
To install Remote Access Services (RAS)
Steps:
1
2
3
4
Click on Start
Go to Settings
Select Control Panel
Double click on the Network icon
If the following window appears, click Yes
If it doesn’t, skip to ‘To configure RAS’
5
6
Uncheck Wired to the network:, by clicking in the check box
Check Remote Access to the network:, clicking in the check box
7
8
9
10
11
Click on Next >
Click on Next > (again) in the Network Adapters: window
Verify the TCP/IP Protocol is selected in the next window, then click on Next >
Click on Next > (again) in the Network Services: window
Click on Next > (again)
Windows NT4
Page 2
12 Insert the drive letter of your Windows NT Disk(s)
13 Click on Continue
14 Click on No
15 In the Remote Access Setup window, click on Add
Windows NT4
Page 3
Installing a New Modem
1
2
In the Add RAS Device window, click on Install Modem
Click on the Don’t detect my modem... check box
3
4
5
6
7
Click on Next >
Click on Have disk…
Insert the drive letter of your setup disk
Click on OK
Select Direct Connection
(nt4_08.bmp)
8
9
Click on Next >
Select COM1 in the ports box
Windows NT4
Page 4
10
11
12
13
14
Click on Next >
If no modem has been previously installed, enter 704 in the Area Code box, then click on Next >
Click on Finish
Back in the Add RAS Device window, click on OK
Back in the Remote Access Setup window, click on Continue
(At this point, the setup will read many files from your NT Disk(s).)
15
16
17
18
19
Click on Next >
Click on Next > (again) to start the network
Click on Next > (again) to make your computer a member of WORKGROUP
Click on Finish
In the Network Settings Change window, click on Yes to restart your computer
To configure Remote Access Services (RAS)
Steps:
1
2
3
4
5
6
Click on Start
Go to Settings
Select Control Panel
Double click on the Network icon
Click on the Services tab
Select Remote Access Service
Windows NT4
Page 5
7
Click on Properties…
If there is a Dial-Up Networking Serial Cable as a device in the Remote Access Setup window:
(like above) continue, otherwise go back to step 15 in the first section of this manual (install
RAS)
8
9
10
11
12
13
Click on Continue
Click on the Protocols tab
Select TCP/IP Protocol
Click on Properties
Click on the DNS tab
In the host box enter your user ID
Windows NT4
Page 6
14 In the Domain box enter appstate.edu
15 In the DNS Server Search Order box enter 152.10.1.15 - Click on Add
enter 152.10.1.5 - Click on Add
enter 152.10.1.1 - Click on Add
16 In the Domain Suffix Search Order box enter appstate.edu Click on Add
17 Click on OK
18 Click on OK in the Network window
19 Close the Control Panels window
To create a Dial-Up Networking Connection
Steps:
1
Double click on My Computer on the desktop
2
Double click on Dial-Up Networking
If your phonebook is empty follow the following steps. Otherwise click New.
3
4
Click on OK
In the ‘Name the new phonebook entry:’ box enter: ASU
Windows NT4
Page 7
5
6
Click on Next >
In the Server window check the ‘Non-windows NT server …’ check box
7
8
9
10
11
12
13
Click on Next >
Click on Next > (again) in the Phone Number window
Verify the Point-to-Point Protocol (PPP) is selected
Click on Next > in the Serial Line Protocol window
Click on Next > in the Login Script window
Click on Next > in the IP Address window
In the DNS server: bow enter: 152.10.1.15
Windows NT4
Page 8
14
15
16
17
18
19
20
21
22
23
24
25
26
27
27
Click on Next >
Click on Finish
Click on More…
Choose Edit entry and modem properties
Click on the Basic tab
Click Configure…
Change Initial Speed (bps) to 57600
Click on OK
Click on the Server tab
make sure tcp/ip is checked and others unchecked
Click on the Script tab
Click on Before Dialing…
Select the ‘Pop up a terminal window’ radio button
Click on OK
Click on OK (again) in the Edit Phone Entry window
Starting your ASU Connection
Steps:
1
2
Double click on My Computer on the desktop
Double click on Dial-Up Networking
Windows NT4
Page 9
3
4
5
Click on Dial
Hit enter until you see an annex: prompt
At the annex prompt type ppp and hit enter
6
If you see non-sense characters after you hit enter (as in the image above) click on Continue.
You may now run WS_FTP, install and run Ewan, and other internet programs.
There is no time limit on this connection. You may disconnect and reconnect at will.
Windows NT4
Page 10