Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download 5968-8153EN
Document related concepts
Buck converter wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Mains electricity wikipedia , lookup
Ground loop (electricity) wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Alternating current wikipedia , lookup
Opto-isolator wikipedia , lookup
Rectiverter wikipedia , lookup
Transcript
Keysight Technologies InfiniiVision Oscilloscope Probes and Accessories For 2000 X-, 3000A/T X-, 4000 X-, 6000 X-, 5000, 6000, and 7000 Series Selection Guide Introduction To achieve the best results from your scope, you need the right probes and accessories for your particular application. That is why Keysight Technologies, Inc. offers a complete family of innovative probes and accessories for InfiniiVision oscilloscopes. For the most up-to-date and complete information about Keysight’s accessories, please visit our Web site at: www.keysight.com/find/probes Table of Contents Probe Compatibility Table...........................................................................................................3 Passive Probes............................................................................................................................5 High-voltage Passive Probes ....................................................................................................9 InfiniiMax Active Probes and Accessories.................................................................................10 InfiniiMode Active Probes and Accessories...............................................................................12 High-voltage Differential Active Probes ...................................................................................14 Single-ended Active Probes.......................................................................................................18 Mixed Signal Oscilloscope Logic Probes ..................................................................................20 Clamp-on Current Probes .........................................................................................................22 High-sensitivity Current Probes ................................................................................................24 Wedge Probe Adapters . ............................................................................................................26 Miscellaneous Accessories . ......................................................................................................27 T2A Probe Interface Adapter......................................................................................................29 Recommended Probes for Low-/Mid-speed Bus Measurements ...........................................30 03 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide Probe Compatibility Table For ordering information when replacing your probe or probe accessory: Refer directly to the page number listed in the Table of Contents for your probe model. To assist you in selecting the proper probe for your application: Use our probe compatibility table below to find the probes that are recommended for use with your 2000 X-, 3000A/T X-, 4000 X-, 6000 X-, 5000, 6000, and 7000 Series InfiniiVision oscilloscope. Probe type Probe model Passive probes, page 4 N2862B/N2841A 10:1 150 MHz (included in 70/100 MHz models) N2863B/N2842A 10:1 300 MHz (included in 200 MHz models) N2890A/N2843A 10:1 500 MHz (included in 350/500 MHz/1 GHz models) N2840A 10:1 50 MHz N2853A 10:1 350 MHz N2894A 10:1 700 MHz (included in 4000 X /6000 X models) N2889A 1:1/10:1 350 MHz N7007A 10:1 400 MHz 10076C 4 kV High-voltage passive probe, page 9 Differential active probes, page 10 Single-ended active probes, page 18 MSO logic probes, page 20 Current probes, page 22 1130A to 1134A 1.5 to 7 GHz N2750A to N2752A 1.5 to 6 GHz N2791A 25 MHz N2891A 70 MHz N2790A 100 MHz (with AutoProbe) N2792A 200 MHz N2818A 200 MHz (with AutoProbe) N2793A 800 MHz N2819A 800 MHz (with AutoProbe) N2804A 300 MHz N2805A 200 MHz N2795A 1 GHz (with AutoProbe) N2796A 2 GHz (with AutoProbe) N2797A 1.5 GHz (with AutoProbe) N7020A 2 GHz 01650-61607 16-channel N2755A 8-channel MSO cable (included in 2000 X-Series MSOs) N2756A 16-channel MSO cable (included in 3000, 4000, and 6000 X-Series MSOs) 1146B 100 kHz N2780B 2 MHz (use with N2779A) N2781B 10 MHz (use with N2779A) N2782B 50 MHz (use with N2779A) N2783B 100 MHz (use with N2779A) 1147B 50 MHz (with AutoProbe) N2893A 100 MHz (with AutoProbe) N2820A 3 MHz/50 µA high sensitivity, 2 channel (with AutoProbe) N2821A 3 MHz/50 µA high sensitivity, 1 channel (with AutoProbe) MSO/DSO 2000 X 1 Recommended Recommended Recommended MSO/DSO 3000A/T X Recommended Recommended Recommended MSO/DSO 4000 X/6000 X 2 Recommended Recommended Recommended Recommended Recommended Compatible Recommended Recommended Recommended Recommended Recommended Compatible Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Incompatible Incompatible Recommended Recommended Incompatible Incompatible Incompatible Incompatible Incompatible Incompatible Incompatible Incompatible Incompatible Incompatible Incompatible Incompatible Recommended Incompatible Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Incompatible Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended 3 Recommended 3 Recommended Recommended Recommended Recommended 3 Recommended Incompatible Recommended Recommended Recommended Recommended Recommended Recommended Incompatible Incompatible Incompatible Incompatible Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended 1. The 2000 X-Series does not support AutoProbe interface active probes. 2. The 4000 X- and 6000 X-Series comes with the Infiniium AutoProbe interface for higher probe power support. 3. Recommended with 4000 X-Series only. 04 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide Probe Compatibility Table (Continued) Probe type Probe model DSO5000A 100 MHz DSO5000A 300 to 500 MHz MSO/DSO6000A 4 100 MHz Passive probes, page 5 N2863B 10:1 300 MHz (included in 5000 Series 100/300 MHz) 10070D 1:1 20 MHz 10073D 10:1 500 MHz (included in 6000/7000 Series 300 MHz to 1 GHz and 5000 Series 500 MHz) 10074D 10:1 150 MHz (included in 6000 Series 100 MHz) N2873A 10: 1 500 MHz (optional to 7000B) N7007A 10:1 400 MHz 10076C 4 kV Recommended Recommended Recommended MSO/DSO6000A 4 300 MHz to 1 GHz MSO/DSO7000A/B 100 MHz to 1 GHz Compatible Recommended Compatible Recommended Recommended Recommended Compatible Recommended Recommended Recommended Compatible Recommended Compatible Recommended Recommended Compatible Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended Recommended 1130A 1.5 GHz 1 N2750A 1.5 GHz N2791A 25 MHz N2891A 70 MHz N2790A 100 MHz (with AutoProbe) N2792A 200 MHz N2818A 200 MHz (with AutoProbe) N2793A 800 MHz N2819A 800 MHz (with AutoProbe) N2804A 300 MHz N2805A 200 MHz N2795A 1 GHz (with AutoProbe) N2796A 2 GHz (with AutoProbe) N2797A 1.5 GHz (with AutoProbe) N7020A 2 GHz 01650-61607 16-channel N6450-60001 2x8-channel (included in MSO6000A, MSO7000A/B) Compatible Incompatible Recommended Recommended Recommended Recommended Incompatible Recommended Incompatible Incompatible Incompatible Recommended Recommended Incompatible Incompatible Incompatible Recommended Incompatible Recommended Recommended Recommended Recommended Incompatible Recommended Incompatible Incompatible Incompatible Recommended Recommended Incompatible Incompatible Incompatible Incompatible Incompatible Recommended Recommended Incompatible Incompatible Incompatible Incompatible Incompatible Incompatible Incompatible Incompatible Incompatible Incompatible Incompatible Recommended Recommended Incompatible Recommended Recommended Recommended Recommended Incompatible Recommended Incompatible Incompatible Incompatible Recommended Recommended Incompatible Incompatible Recommended 1146B 100 kHz N2780B 2 MHz (use with N2779A) N2781B 10 MHz (use with N2779A) N2782B 50 MHz (use with N2779A) N2783B 100 MHz (use with N2779A) 1147B 50 MHz (with AutoProbe) N2893A 100 MHz (with AutoProbe) N2820A 3 MHz/50 µA high sensitivity, 2 channel (with AutoProbe) N2821A 3 MHz/50 µA high sensitivity, 1 channel (with AutoProbe) Recommended Recommended Recommended Recommended Recommended Recommended Recommended Incompatible Recommended Recommended Recommended Recommended Recommended Recommended Recommended Incompatible Recommended Recommended Recommended Recommended Recommended Incompatible Incompatible Incompatible Recommended Recommended Recommended Recommended Recommended Recommended Recommended Incompatible Incompatible Incompatible Incompatible Incompatible High-voltage passive probe, page 9 Differential active probes, page 10 Single-ended active probes, page 18 Mixed signal oscilloscope logic probes 2, page 20 Current probes, page 22 1. The 1130A probe amplifier supports both single- and differential-ended measurements. Higher bandwidth InfiniiMax probe model 1131A, 1132A, and 1134A are also supported by 3000 X-, 4000 X-, 6000 X-, 5000, 6000 300 MHz to 1 GHz models and, 7000 Series. 2. Recommended for InfiniiVision MSOs only. 3. These Infiniium active probes are not supported by InfiniiVision Series scopes – 1152A, 1153A, 1154A, 1155A, 1159A, 1168A, 1169A, N2800A, N2801A, N2802A, N2803A, N2830A, N2831A, N2832A, N7000A, N7001A, N7002A, and N7003A. 4. MSO/DSO6000A 100‑MHz models do not support any Keysight active probes with AutoProbe interface. 05 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide Passive Probes – Designed for optimal performance with your Keysight InfiniiVision Series oscilloscopes – 1:1 and 10:1 attenuation ratio – 20 to 700 MHz Accessories available for 10070D/73D/74D passive probes N4848A Rugged, high-quality probes at a reasonable price 5081-7696 Keysight 10070-family passive probes are a great choice if you are looking for high quality at a very reasonable price. These general-purpose probes are designed specifically to give you optimal performance with your InfiniiVision Series oscilloscopes. Ruggedized for generalpurpose measurements, they feature a durable cable and a solid stainless steel probe body encased with a hard, fracture-resistant plastic. They are designed and tested to ensure the probes operate in the toughest of conditions N4847A The N28xxA/B low-cost, generalpurpose passive probes provide up to 500 MHz bandwidth and feature a high input resistance of 10 MΩ for low probe loading. These probes provide a 10:1 attenuation ratio except for the N2889A, which provides a switch in the probe handle for switching the attenuation ratio between 1:1 and 10:1. The N284xA and N2853A are the new version of passive probes with improved frequency response over N2862B/63B/90A probes. This probe cable can be used in place of existing N2862B/63B/90A for better performance. The N2853A is a 10:1 passive probe with 2 m cable length for extended cable connection. The N2873A/N2894A are 500-MHz/ 700 MHz 10:1 miniature passive probes that can be used with all InfiniiVision Series. Compact 2.5-mm probe head diameter, low input capacitance, and various fine-pitch probe tip accessories make the N2873A/N2894A passive probes ideal for probing densely populated IC components or surfacemount devices used in today’s high-speed digital applications. The N2894A provides 700 MHz system bandwidth when used in conjunction with the 4000 X- and 6000 X-Series ≥ 1 GHz models. For more information about N2870A Series passive probes and accessories, refer to Keysight’s literature number, 5990-3930EN. N4849A 5081-7690 10072A 10075A Probe-tip-to-BNC (m) adapter, qty 2 Ground lead with alligator clip for 1007x and N2862B/63B/89A/90A Retractable hook tip for 1007xC/D (not compatible with 10076A/B), qty 2 Dual-test lead adapter (for 10070/3/4x), qty 2 Replacement parts accessory kit Fine-pitch probing kit includes 10 SMT clips and 2 dual-lead adapters 0.5 mm IC probing kit. Contains 4 0.5 mm IC clips and 2 duallead adapters Accessories available for N2862B/63B/89A/90A and N2840A/41A/42A/43A/53A passive probe N2856A N2857A N2859A N2858A N4827A N4826A N4828A 1250-3978 Accessory kit (containing all standard accessories) Alligator ground lead, qty 1 Replaceable probe tip Retractable hook tip, qty 1 PCB socket adapter, qty 2 Dual-lead adapter for, qty 2 5 mm ground spring for, qty 2 BNC adapter Accessories available for N2873A/N2894A (and other N287xA Series passive probes) N4829A N4831A N4837A 0960-2908 N4836A 0960-2977 0960-2978 0960-2979 N4838A 0960-2981 0960-2982 0960-2983 0960-2984 0960-2985 0960-2986 0960-2987 0960-2988 0960-2989 0960-2990 N4863A N4864A Probe tip kit (rigid and spring loaded), 10 each Sprung hook adapter 2.5 mm for N2870A/71A/ 72A/73A/75A, N2894A, qty 2 Ground lead 15 cm, qty 2 10 self-adhesive copper pads 2x2 Dual lead-adapter, 2.5 mm, 10 cm, qty 2 Ground lead 11 cm to Miniclip Ground lead 11 cm to 0.8 mm socket Rigid probe tips, qty 5 Ground spring 2.5 mm, qty 2 Spring-loaded probe tip, qty 5 Ground blade 2.5 mm IC cap 2.5 to 0.5 mm Green IC cap 2.5 to 0.65 mm Blue Insulating cap 2.5 mm IC cap 2.5 to 1.27 mm Black IC cap 2.5 to 1.27 mm Black IC cap 2.5 to 0.8 mm Gray IC cap 2.5 to 1.0 mm Brown Adapter 2.5 to 0.8 mm socket 2.5 mm probe tip-to-PCB adapter, horizontal 2.5 mm probe tip-to-PCB adapter, vertical Standard accessories that come with each probe 10070D/10073C/10074C Retractable hook tip, qty 1 Colored identification tag, 2 each of 4 colors Ground bayonet, qty 1 IC insulation cap, qty 1 Adjustment tool, qty 1 Ground lead, qty 1 BNC adapter, qty 1 N2862B/63B/89A/90A and N2840A/41A/42A/43A/53A Retractable hook tip, qty 1 Colored identification tag, 2 each of 4 colors Spring ground, qty 1 IC insulation cap, qty 1 Insulation cap, qty 1 Adjustment tool, qty 1 (with N2862B/63B), qty 2 (with N2889A/90A) Ground lead, qty 1 BNC adapter, qty 1 Probe tip, qty 1 N2873A /N2894A Spring loaded probe tips, qty 2 Rigid probe tips, qty 2 Ground blade, qty 1 Ground spring, qty 1 Sprung hook, qty 1 Ground lead, qty 1 Copper pads, qty 2 IC cap to 0.5 mm, 0.65 mm, 0.8 mm, 1 mm, 1.27 mm, qty 1 each BNC adapter, qty 1 Insulating cap, qty 1 Protection cap, qty 1 Trimmer tool, qty 1 Color coded rings, 3x4 colors 06 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide Passive Probes (Continued) Ordering information for Keysight passive probes 10070D N2840A N2862B/N2841A N2853A 10074D N2863B/N2842A N2889A 10073D N2890A/N2843A N2873A N2894A N7007A 1:1 20 MHz passive probe 10:1 50 MHz passive probe 10:1 150 MHz passive probe 10:1 350 MHz passive probe (2 m cable) 10:1 150 MHz passive probe 10:1 300 MHz passive probe 10:1/1:1 350 MHz passive probe 10:1 500 MHz passive probe 10:1 500 MHz passive probe 10:1 500 MHz miniature passive probe 10:1 700 MHz miniature passive probe 10:1 400 MHz extreme temperature passive probe (2 m cable) 10073D/74D passive probe N2873A/N2894A passive probe with standard accessories N2862B/63B/90A passive probe N2889A 10:1/1:1 passive probe N2840A/41A/42A/43A/53A passive probe 07 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide Passive Probes (Continued) Characteristics for Keysight passive probes Bandwidth Risetime (calculated) Attenuation ratio Input resistance Input capacitance Maximum input (dc + peak ac) Compensation range Probe readout Cable length 10070D 20 MHz < 17.5 ns 1:1 1 MΩ Approx 70 pF 300 Vpk CAT I 150 Vpk CAT II None Yes 1.5 m Attenuation ratio Input resistance N2862B,41A/ N2863B,42A 150 MHz/ 300 MHz < 2.33 ns/ < 1.16 ns 10:1 10 MΩ Input capacitance Approx 11 pF Maximum input (dc + peak ac) 300 V CAT I/II Compensation range Probe readout Cable length 5 to 30 pF Yes 1.2 m Bandwidth Risetime (calculated) 10073D 500 MHz < 700 ps 10:1 2.2 MΩ Approx 12 pF 500 Vpk CAT I 400 Vpk CAT II 6 to 15 pF Yes 1.5 m 10074D 150 MHz < 2.33 ns 10:1 10 MΩ Approx 15 pF 500 Vpk CAT I 400 Vpk CAT II 9 to 17 pF Yes 1.5 m N2889A N2890A/N2843A N2873A/N2894A N2853A N2840A 350 MHz (at 10:1), 10 MHz (at 1:1) <1 ns (at 10:1), < 35 ns (at 1:1) 1:1/10:1 switchable 10 MΩ (at 10:1) 1 MΩ (at 1:1) Approx 11 pF (at 10:1), 60 pF (at 1:1) 300 V CAT I/II (at 10:1), 150 V CAT I/ II (at 1:1) 5 to 30 pF (at 10:1) No 1.3 m 500 MHz 500 /700 MHz 350 MHz 50 MHz < 700 ps < 1 ns < 7 ns 10:1 10 MΩ < 700 ps/ < 500 ps 10:1 10 MΩ 10:1 10 MΩ 10: 1 10 MΩ Approx 11 pF Approx 9.5 pF Approx 11 pF Approx 11 pF 300 V CAT I/II 400 V CAT I, 300 V CAT II 300 V CAT I/II 300 V CAT I/II 5 to 30 pF Yes 1.3 m 10 to 25 pF Yes 1.2 m 5 to 30 pF Yes 2m 5 to 30 pF No 1.2 m Note: 700 MHz BW only available on DSOX/MSOX 4000 X-Series oscilloscopes with 1 GHz or 1.5 GHz bandwidth models. 08 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide N7007A Extreme Temperature Passive Probe Features and specifications – Wide operating temperature range of –40 to +85 °C for extreme temperature environmental chamber testing – 400 MHz bandwidth (–3 dB) – High impedance (10 MΩ at DC) input – Wide input range: 1 kV CAT II, 600 V CAT III – Includes hook tip adapters (x2), ground leads (x2) and spring ground tip (x1) The N7007A 400 MHz passive probe is a low-cost, high impedance passive probe with rugged probe tips for environmental chamber testing from –40 to +85 °C. Its large input impedance (10 MΩ at DC) and wide input voltage range (1,000 Vdc + peak AC CATII) makes the probe ideal for a broad range of general purpose extreme temperature applications. Key characteristics Bandwidth Attenuation ratio Input impedance (at DC) Oscilloscope compensation range Operating temperature range Operating humidity range Cable length Max input range N7007A Extreme temperature passive probe N7007A 400 MHz (with spring ground), 70 MHz (with ground lead) 10:1 10 MΩ/15.5 pF (when terminated into 1 MΩ) 6 to 18 pF –40 to +85 °C < 90% at 40 °C 2m 1 kV CAT II, 600 V CAT III Ordering information N7007A N7006A N7008A N7009A 10:1 400 MHz extreme temperature passive probe Spring ground for N7007A Hook tip adapter for N7007A Ground lead for N7007A N7006A spring ground N7008A hook tip adapter N7009A ground lead 09 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide High-voltage Passive Probes – Ideal for measuring up to 4 kV – Up to 500 MHz bandwidth – 100:1 attenuation 10076C high-voltage probe The Keysight 10076C 4 kV 100:1 passive probe gives you the voltage and bandwidth you need for making high-voltage measurements. Its compact design makes it easier to probe today’s small power electronics components and its rugged construction means it can withstand rough handling without breaking. 10076C passive probe Characteristics 10076C Bandwidth Risetime (calculated) Attenuation ratio Input resistance Input capacitance Maximum input Compensation Probe readout Cable length 500 MHz (–3 dB) < 0.7 ns 100:1 66.7 MΩ (when terminated into 1 MΩ) Approx 3 pF 4000 Vpk 6 to 20 pF range Yes 1.8 m N2789A spring ground clip for 10076B/C Ordering information for Keysight high‑voltage probes 10076C 10077A N2789A High-voltage probe: includes one retractable hook tip, one ground‑bayonet, one IC probing tip, one alligator ground lead, one spring ground tip and a compensation screwdriver Accessory kit for 10076A/C: includes one retractable pincher tip, one ground lead, one insulation cap, two measuring pins, and two colored tags Spring ground tip for 10076B/C 10077A accessory kit for 10076A/B 10076C derating curve 10 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide InfiniiMax Active Probes and Accessories 1130A-34A InfiniiMax high-performance active probe system – 1.5 to 7 GHz InfiniiMax probe system – InfiniiMax probe amplifier supports both differential- and single-ended measurements for a more costeffective solution – Unrivaled InfiniiMax probing accessories support browsing, solder-in, and socketed use models at the maximum performance available – Compatible with 3000 X/T-, 4000 X-, 6000 X-, 5000, 6000, and 7000 Series oscilloscopes (except for 6000 Series 100-MHz models) The InfiniiMax 1130A Series probe amplifier is a perfect complement to the InfiniiVision 1 GHz or higher bandwidth models. Its bandwidth, extremely low input capacitance (0.32 pF), high common mode rejection, and patented resistor probe tip technology provide ultra low loading of the DUT and superior signal fidelity. Keysight’s innovative InfiniiMax 1130A Series differential probe is the easiest-to-use, highest performance probing system available for high-speed digital design, and represents a new industry standard for accuracy, flexibility, and reliability. Designers can achieve full system bandwidth in conjunction with InfiniiVision Series oscilloscopes even when manually browsing with the probe or making hands-off measurements. Operating characteristics Probe bandwidth (–3 dB) Rise and fall time (10 to 90%) Input capacitance Input resistance Input dynamic range Input common mode range Maximum signal slew rate DC attenuation Offset range Maximum input voltage ESD tolerance Maximum number of probes supported by 3000 X/T-/ 5000/6000/7000 Series Maximum number of probes supported by 4000 X- and 6000 X-Series 1134A: > 7 GHz 1132A: > 5 GHz 1131A: > 3.5 GHz 1130A: > 1.5 GHz 1134A: 60 ps 1132A: 86 ps 1131A: 100 ps 1130A: 233 ps Cm = 0.1 pF Cm is between tips Cg = 0.34 pF Cg is ground for each tip Cdiff = 0.27 pF differential mode capacitance = Cm + Cg/2 Cse = 0.44 pF single-ended mode capacitance = Cm + Cg Differential mode resistance = 50 kΩ ± 2% Single-ended mode resistance = 25 kΩ ± 2% ± 2.5 V ± 6.75 Vdc to 100 Hz; ± 1.25 V > 100 Hz 18 V/ns when probing a single-ended signal 30 V/ns when probing a differential signal 10:1 ± 3% before calibration on oscilloscope 10:1 ± 1% after calibration on oscilloscope ± 12.0 V when probing single-ended signal 30 Vpeak, CAT I > 8 kV from 100 pF, 300 Ω HBM 2 4 Optional solder-in probe heads and solder-in sockets, as well as browser configuration provide full bandwidth at the probe tip. Keysight 1130A InfiniiMax probe offers you the highest performance available for measuring differential and single-ended signals 11 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide InfiniiMax Active Probes and Accessories (Continued) 1130A-34A InfiniiMax high-performance active probe system Ordering information for Keysight InfiniiMax 1130A Series probe and accessories Probe amplifier 1130A 1131A 1132A 1134A Connectivity kits E2669A E2668A Individual probe heads E2675A E2676A E2677B E2678A E2679A N2851A N2849A N5380B N5425B/N5426A N5451A N5450B N2880A N2881A 1.5 GHz InfiniiMax probe amplifier (order one or more probe heads or connectivity kits per amplifier) 3.5 GHz InfiniiMax probe amplifier (order one or more probe heads or connectivity kits per amplifier) 5 GHz InfiniiMax probe amplifier (order one or more probe heads or connectivity kits per amplifier) 7 GHz InfiniiMax probe amplifier (order one or more probe heads or connectivity kits per amplifier) InfiniiMax connectivity kit for differential/single-ended measurements InfiniiMax connectivity kit for single-ended measurements InfiniiMax differential browser probe head and accessories InfiniiMax single-ended browser probe head and accessories InfiniiMax differential solder-in probe head and accessories InfiniiMax single-ended/differential socketed probe head and accessories InfiniiMax single-ended socketed probe head and accessories QuickTip probe head for InfiniiMax I/II probe amp QuickTip tips for N2851A InfiniiMax II differential SMA head 12-GHz differential ZIF solder-in probe head and ZIF probe tips InfiniiMax long-wire ZIF probe tips (for use with N5425B ZIF probe head) InfiniiMax extreme temperature extension cable (that allows for probing in environments from —55 to +150 °C) InfiniiMax in-line attenuator kit (pairs of 6 dB, 12 dB and 20 dB attenuator in a kit) InfiniiMax DC blocking caps (a pair of 30 Vdc blocking cap) InfiniiMax solder-in probe head with long wires InfiniiMax ZIF tip soldered on board InfiniiMax browser head For more comprehensive information about the 1130A InfiniiMax probe amplifier and its accessories, refer to the Keysight Infiniium Osclloscope Probes, Accessories, and Options data sheet with Keysight literature number 5968-7141EN. 12 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide InfiniiMode Active Probes and Accessories N2750A-52A InfiniiMode probe – 1.5 to 6 GHz bandwidth – Dual attenuation ratio (2:1/10:1) – InfiniiMode probing for making differential, single-ended and common mode measurements with a single probe – Built-in quick action scope control for quick access to a variety of scope functions – Built-in headlight – Includes solder-in, browser, and socketed tips standard – AutoProbe interface for auto configuration and probe power This, accompanied with superior signal fidelity, makes these probes useful for most digital design and debug applications. And with their wide dynamic range (10 Vpp) and offset range (± 15 V), these probes can be used in a wide variety of analog signal measurements as well. InfiniiMode usability The N2750A comes with new InfiniiMode operation modes. The InfiniiMode allows convenient measurements of differential, single-ended, and common mode signals with a single probe tip without reconnecting the probe to change the connection. The N2750A probe’s InfiniiMode provides the following modes of operation. – A – B (differential), – A – ground (single-ended A) – B – ground (single-ended B) – (A+B)/2 – ground (common mode) Quick action scope control The N2750A Series InfiniiMode differential probe is a new generation of low-cost, differential active probe compatible with InfiniiVision 3000 X-, 4000 X-, 6000 X-Series and Infiniium oscilloscope’s AutoProbe interface. Measurement versatility The N2750A Series InfiniiMode probe offer 2:1 and 10:1 dual attenuation settings, allowing them to be used for a broad range of applications. Dual attenuation range is automatically configured depending on the size of the input signal. The new differential probe has an input resistance of 200 kΩ (differential) or 100 kΩ (each input to ground), and an extremely low input capacitance of 700 fF to minimize circuit loading. The N2750A Series InfiniiMode probe provides convenient and quick access to various functions on the scope. You often have a need to control the scope while you hold a probe in your hand. With the quick action scope control feature built into the probe, you can turn the built-in headlight of the probe on and off, or control some frequently used scope functions such as RUN/STOP, auto scale, quick print, and quick save with only a button press on the probe. Get control of your most needed function with a push of the quick action control button on the probe. Flexibility in probe use models is also a vital necessity. The probes come standard with three different types of exchangeable probe tips that allow for easy connections to the circuit under test. These probe tips enable you to access multiple signals on anything from header connectors to hard-to-reach, highdensity circuitry. The probes are equipped with a white LED headlight to illuminate the circuit under test which will help you see where you are probing. This probe is compatible with InfiniiVision 3000 X-Series with software ver. 2.2 or above, 4000 X-Series with software ver. 3.01 or above, and 6000 X-Series with software ver. 6.00. Ordering information for InfiniiMode probes and accessories N2750A 1.5 GHz InfiniiMode differential probe N2751A 3.5 GHz InfiniiMode differential probe N2752A 6 GHz InfiniiMode differential probe N2776A Differential browser tips (qty 3) N2777A InfiniiMode solder-in tips (qty 3) N2778A InfiniiMode socketed tips (qty 3) N4822A Socketed tip for USB/Ethernet application fixtures (qty 1) Each probe includes two solder-in tips, two socketed tips and two browser tips. 13 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide InfiniiMode Active Probes and Accessories (Continued) Characteristics and specifications for N2750A Series InfiniiMode probes Model number Probe bandwidth 1 (–3 dB) Rise time, probe only (10 to 90%) Input resistance (at DC) 1 Input capacitance Attenuation ratio (at DC) Input dynamic range Input common mode range Offset range Offset accuracy 2 Maximum non-destructive input voltage Maximum number of probes supported by 3000 X-Series Maximum number of probes supported by 4000 X-, 6000 X-Series N2750A 1.5 GHz 233 ps 200 kΩ ± 2% (differential mode) 100 kΩ ± 2% (single-ended mode) 50 kΩ ± 2% (common mode) 700 fF (with browser) 2:1 / 10:1 ± 1 V, 2 Vpp (at 2:1) / ± 5 V, 10 Vpp (at 10:1) ± 15 V (from DC to 100 Hz), ± 2.5 V (for >100 Hz) 3 ± 15 V < 3% ± 30 V (DC + peak AC) 1 4 N2751A 3.5 GHz 100 ps N2752A 6 GHz 58.3 ps 1. Denotes warranted electrical specifications at 2:1 attenuation mode after 20 minute warm-up. All others are typical. 2. When calibrated on the oscilloscope, these characteristics are determined by the oscilloscope characteristics. 3. Assumes symmetric differential signals. N2750A with browser tip N2750A with socketed tip N2750A with solder-in tip For more information about the N2750A Series InfiniiMode probes, refer to the data sheet with the Keysight literature number, 5991-0560EN. 14 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide High-voltage Differential Active Probes – 25 to 800 MHz bandwidth – Switchable attenuation – Measure up to 1,400 V CAT II and 7 kV CAT I N2790A/91A and N2891A high voltage differential probes Oscilloscope users often need to make floating measurements where neither point of the measurement is at earth ground. Use N2790A, N2791A, or N2891A high voltage differential probes to make safe and accurate floating measurements with an oscilloscope. The N2790A, N2791A, and N2891A high voltage differential probes allow conventional earth-grounded Keysight oscilloscopes to be used for floating signal measurements. Each probe offers user-selectable attenuation settings that makes it highly versatile, allowing it to be used for a broad range of applications. The probe comes with probe tip accessories for use with small and large components in tight spaces. The N2791A and N2891A are compatible with any oscilloscope with 1 MΩ BNC input. The N2791A and N2891A probe power is supplied by included 4x AA batteries or USB host port of the scope or PC via a supplied USB power cable. The N2790A is compatible with the Keysight’s AutoProbe interface where the probe power is supplied by the Keysight oscilloscope’s probe interface. 1141A 200 MHz differential probe The 1141A is a 1x FET differential probe with 200‑MHz bandwidth and a 3000:1 CMRR. The probe has a high-input resistance and low-input capacitance of 7 pF to minimize circuit loading. The 1141A must be used with 1142A probe control and power module, which controls input coupling modes dc, dc with variable offset, and dc reject. Two attenuators, 10x and 100x are provided to expand the linear differential input range to ± 30 V. This probe works with any 50‑Ω input oscilloscope including 3000 X-, 4000 X-, 5000, 6000X, 6000, 300 MHz to 1 GHz, and 7000 Series. Bandwidth Risetime Attenuation ratio CMRR Input impedance (between inputs) Max input voltage to ground Max input voltage between two inputs Max number of probes supported by 3000 X-/4000 X-/ 5000/6000/7000 Series N2790A 100 MHz 3.5 ns 50:1 / 500:1 —80 dB at 50/60 Hz —50 dB at 1 kHz —50 dB at 1 MHz 8 MΩ / 3.5 pF N2791A 25 MHz 14 ns 10:1 / 100:1 —80 dB at 50/60 Hz —40 dB at 1 MHz N2891A 70 MHz 5 ns 100:1 / 1000:1 –80 dB at 50/60 Hz –60 dB at 20 kHz 8 MΩ / 8 pF 100 MΩ / 5 pF ± 1000 V (CAT II) ± 600 V (CAT III) ± 1400 V at 500:1 ± 140 V at 50:1 4 ± 700 V at 100:1 ± 70 V at 10:1 ± 700 V at 100:1 ± 70 V at 10:1 4 ± 7000 V at 1000:1 ± 700 V at 100:1 ± 7000 V at 1000:1 ± 700 V at 100:1 4 15 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide High-voltage Differential Active Probes (Continued) N7013A extreme temperature extension cable kit The N7013A is a 70-cm long extreme temperature extension cable kit compatible with four of Keysight’s medium- and high-voltage differential active probes, including the N2790A, N2791A, N2792A, and N2818A. These probes are typically used in power supply testing applications, as well as testing automotive differential buses including CAN, CAN FD, and FlexRay. With the N7013A extension kit, the main body of the temperature-sensitive differential active probe can be placed outside of the environmental chamber, while the extension kit (70-cm long cable pair) and connection adapters can be extended into the environmental chamber under extreme-temperature conditions ranging from -40 to +85 °C. The N7013A kit includes: – 1 pair of extreme-temperature differential extension cables – 1 pair of extreme-temperature hook tip adapters – 1 pair of extreme-temperature banana-to-socketed tip adapters for connecting to 0.025” square pins The N7014A accessory includes: 1 pair of banana-to-socketed tip adapters Key characteristics Temperature range Cable length Derated bandwidth N2818A, N2792A, N2790A Derated bandwidth with N2791A —40 to +85 °C 70 cm 70 MHz 25 MHz N7007A extreme temperature passive probe 16 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide High-voltage Differential Active Probes (Continued) N2804A/N2805A high-voltage, high-speed differential probes The N2804A and N2805A differential probes provide the superior general-purpose differential signal measurements that are required for high-speed power measurements such as measuring characteristics of switching power devices, DC-DC converters or class D amplifiers, vehicle bus measurements, and high-speed digital system designs. The N2804A 300-MHz differential probe offers 100:1 attenuation ratio, allowing it to be used adequately for high voltage signal measurements. The differential probe has a differential input resistance of 4 MΩ and low input capacitance of 4 pF to minimize circuit loading. The probe comes with a pair of extension leads (30 cm long) with a damping resistor built-in to damp out the in-band resonance and provide flat frequency response even while using the extension leads and probe tip accessories. The N2805A is a 200-MHz differential probe designed to provide superior differential signal measurements with a long cable length (5 m), making it ideal in an environment where extended cable length is required. This probe comes with an extensive set of probe tip accessories for use with small and large components in tight spaces. Characteristics for N2804A and N2805A N2804A N2805A Bandwidth 300 MHz (without extension leads) 200 MHz 120 MHz (with extension leads) Attenuation ratio 100:1 50:1 CMRR —80 dB at 50/60 Hz —75 dB at 50/60 Hz —75 dB at 1 MHz —80 dB at 1 MHz Input impedance 4 MΩ // 4 pF 4 MΩ // 4 pF (between inputs) Max input voltage ± 300 V (DC+ peak AC) and ± 200 V (DC+ peak AC) and (between two inputs) ± 200 Vrms ± 200 Vrms CAT II Max input voltage ± 300 V (DC+ peak AC) and ± 500 V (DC+ peak AC) and ± 200 Vrms CATII ± 500 Vrms CAT I ± 1000 V (DC+ peak AC) and ± 300 V (DC+ peak AC) and ± 1000 Vrms CATI ± 200 Vrms CATII Cable length 1.2 m 5m Max number of probes 4 4 supported by InfiniiVision Series Compatible InfiniiVision 4000X Series with software ver. 4.0 or higher, 3000X Series with oscilloscopes software ver. 2.38 or higher N2804A 300 MHz differential probe For more information about the N7020A power rail probe, refer to the Keysight data sheet with the publication number 5992-0141EN. N2805A 200 MHz differential probe 17 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide High-voltage Differential Active Probes (Continued) N2792A/N2818A 200-MHz and N2793A/N2819A 800-MHz general-purpose differential probe The N2792A/N2818A 200-MHz and N2793A/N2819A 800-MHz differential probes provide the superior general-purpose differential signal measurements required for today’s high-speed power measurements, vehicle bus measurements, and digital system designs. The N2792A/N2818A and N2793A/N2819A probes offer a 10:1 attenuation setting, high input resistance, and low input capacitance to minimize circuit loading. The N2792A/93A are compatible with any oscilloscope with 50 Ω BNC input. The probe can be powered by any USB port on a scope or computer, or by a 9 V battery. The N2818A/19A are the AutoProbe interface versions of the N2792A/93A. They are compatible with the InfiniiVision 3000 X-, 4000 X- and 6000 X-Series only. N2790A 100-MHz, 1.4-kV differential probe with AutoProbe interface Characteristics for N2792A/N2818A and N2793A/N2819A differential probes Bandwidth Risetime Attenuation ratio CMRR Input impedance (between inputs) Max input voltage to ground Max input voltage between two inputs Max number of probes supported by InfiniiVision Series N2792A/N2818A 200 MHz 1.75 ns 10:1 —80 dB at 50/60 Hz —50 dB at 10 MHz 1 MΩ // 3.5 pF ± 60 V ± 20 V 4 N2793A/N2819A 800 MHz 437 ps 10:1 —60 dB at 50/60 Hz —15 dB at 500 MHz 200 kΩ // 1 pF ± 40 V ± 15 V 4 N2791A 25-MHz, 700-V differential probe Ordering information for Keysight high voltage differential probes, power supplies and accessories N2790A N2791A N2792A N2818A N2793A N2819A N2891A N4853A N4854A N2804A N2805A N2816A N2817A N7013A 100-MHz, 1.4 kV differential probe with AutoProbe interface 25-MHz, 700-V differential probe 200-MHz, 20-V differential probe 200-MHz, 20-V differential probe with AutoProbe interface 800-MHz, 15-V differential probe 800-MHz, 15-V differential probe with AutoProbe interface 70-MHz, 7,000-V differential probe Variable pitch browser for N2793A/N2819A, qty 2 DC blocking capacitor for N2793A/N2819A, qty 2 300 MHz high voltage differential probe 200 MHz high voltage differential probe with extended cable length Probe tip accessory kit for N2804A including 2 alligator clips, 2 pincer clips, and 2 extension leads (30 cm) Probe tip accessory kit for N2805A including 2 alligator clips, 2 hook clips, 2 pincer clips, and 2 browser tips Extreme temperature extension cable kit for N2790A, N2791A, N2792A, and N2818A N2792A 200-MHz, 20-V differential probe N2793A 800-MHz, 15-V differential probe 18 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide Single-ended Active Probes N2795A/96A/97A low-cost single-ended active voltage – High resistance (1 MΩ) and low capacitance (1 pF) input for low loading – Wide input dynamic range (± 8 V) and offset range (± 12 V for N2796A/97A, ± 8 V for N2795A) – Built-in headlight – Direct connection to AutoProbe interface (no power supply required) – N2797A for extreme temperature environmental chamber testing at –40 to +85 °C The N2795A/96A are a new generation of low-cost, 1 to 2 GHz single-ended active probes with the AutoProbe interface (compatible with Keysight’s InfiniiVision and Infiniium family of oscilloscopes). These probes integrate many of the characteristics needed for today’s general-purpose, high-speed probing– especially in digital system design, component design/characterization, and educational research applications. Its 1 MΩ input resistance and extremely low input capacitance (1 pF) provide ultra low loading of the DUT. This, accompanied with superior signal fidelity, makes these probes useful for most of today’s digital logic voltages. Testing devices over extreme temperature ranges is quite common these days. The N2797A 1.5 GHz single-ended active probe is the industry’s first low-cost high input impedance active probe with rugged probe tips for environmental chamber testing of ICs and devices. It gives the ability to probe signals at drastic temperature swings ranging from –40 to +85 °C. The probe provides a 2 m long cable. Order N2798A for re-ordering accessories. The N2795A/96A/97A are equipped with a white LED headlight to illuminate the circuit under test. The probes are powered directly by the InfiniiVision and Infiniium Autoprobe interface, eliminating the need for an additional power supply. The probes also come with a number of accessories that allow for easy connections to the circuit under test. Model number Probe bandwidth 1 (–3 dB) Risetime System bandwidth N2795A 1 GHz 350 ps 500/600 MHz with Keysight’s 500/600 MHz InfiniiVision/Infiniium, 1 GHz with 1 GHz InfiniiVision 3000 X, 4000 X 10:1 ± 0.5% –8 to +8 V (DC or peak AC) –20 to +20 V ±8V ± 1 mV 0.5% at 70 Hz, 1 Vpp 1 MΩ 1 pF 50 Ω 2 Attenuation ratio (at dc) Input dynamic range Non-destructive input voltage Offset range DC offset error (output zero) Low frequency accuracy Input resistance 1 Input capacitance Output impedance Max number of probes supported by InfiniiVision 3000 X-/5000/6000/7000 Series 2 Max number of probes 4 supported by InfiniiVision 4000X, 6000X N2796A N2797A 2 GHz 1.5 GHz 175 ps 233 psec 1 GHz with Keysight’s 1 GHz InfiniiVision/Infiniium, 1.5 GHz with Keysight’s 1.5 GHz InfiniiVision 4000 X, 6000 X ± 12 V 1. Denotes warranted electrical specifications after 20 minute warm-up, all others are typical. 2. The N2797A is compatible with 3000 X/T-, 4000 X- and 6000 X-Series only. Replacement accessories N4839A N4840A N4841A N4842A N4843A N4844A N4845A N4846A Dual lead socketed adapter, 6 cm, qty 2 Dual lead solder-in adapter, 5 cm, qty 2 Dual lead socketed adapter, 9 cm, qty 2 Dual pin PCB header, qty 2 Solderable tips, qty 10 Right angle ground lead, 5 cm, qty 2 Ground blade, qty 2 Offset ground, qty 2 For more information about N2795A/96A/97A active probe, refer to the Keysight N2795A/96A/97A active probe data sheet, literature number 5990-6480EN 19 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide Single-ended Active Probes (Continued) N7020A power rail probe – 2-GHz single-ended active probe for power rail noise measurement – 1:1 attenuation ratio ensures low noise signal measurement – ± 24 V of probe offset range enables effective elimination of DC component of a power supply. The N7020A power rail probe is a low noise, large offset range oscilloscope probe that enables users to measure small signals riding on top of DC power rails. – Low noise: The N7020A power rail probe is a 1:1 attenuation ratio active probe. As a general rule, the higher a probes attenuation ratio, the nosier the signal will be on the oscilloscope. – Large offset range: The N7020A power rail probe provides ± 24 V of probe offset. This enables users to center the signal on screen while placing the oscilloscope at its maximum vertical sensitivity and zoom in on the signal. – Low DC loading: The N7020A power rail probe has 50 kΩ input impedance at DC, minimizing the probe’s DC loading of the power rail. – Large input dynamic range: The N7020A power rail probe’s ± 850 mV input dynamic range means that users can measure up to ± 850 mV deviations of their DC supplies. This is very useful for measuring programmable supplies like those used in microcontroller power saving modes. – Supporting three connection options — pigtail solder head (2 GHz), SMA (2 GHz), and browser (350 MHz). Characteristics and specifications Probe bandwidth (—3dB) Attenuation ratio Offset range Input impedance at DC at > 1 MHz Input dynamic range Probe noise Included accessories Max number of probes supported by InfiniiVision Compatible InfiniiVision oscilloscopes 2 GHz 1:1 ± 24 V 50 kΩ 50 Ω ± 850 mV 10% of oscilloscope noise N7021A coaxial probe head (qty. 3), N7022A SMA main cable, N7023A browser kit 4 3000X/T-Series with software ver. 2.38 or higher 4000 X-Series with software rev. 4.0 or higher 6000 X-Series with software rev. 6.10 or higher For more information about the N7020A power rail probe, refer to the Keysight data sheet with the publication number 5992-0141EN. N7020A power rail probe N7023A browser kit (now included in the N7020A or orderable separately) 20 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide Mixed Signal Oscilloscope Logic Probes – Compatible with all 40-pin logic probes – Flying leads offer flexibility and convenience MSO probes offer great value and performance These logic probes for the InfiniiVision mixed signal oscilloscopes (MSOs) are the same ones used with Keysight industryleading high-performance logic analyzers. This means we can offer the best performance, great value, and access to the industry’s broadest range of logic probing accessories. The N2756A 4 x 4 signal logic probes are divided into four sets of four channels so you can probe pins that are far apart and work conveniently with only one set if that’s all you require. For optimal signal fidelity, connect ground at each logic probe, in addition to taking a common ground to all four signals via a separate ground connector on the probe pod. The N2756A probe is included with 3000, 4000, and 6000 X-Series MSOs. Characteristics for Keysight 54620‑68701, N6450-60001, N6459-60001 logic probes Input impedance Input capacitance Ordering information for Keysight logic probes N2756A 100 kΩ 8 pF The 01650-61607 is the 40-pin (F) to 40‑pin (F) logic probe cable for Keysight’s InfiniiVision and 54600 Series MSOs. This cable gives the MSO the standard 40-pin female input connector that many Keysight logic analyzers have. With this cable, a user can connect a wide variety of logic analyzer probes such as Mictor, Samtec, and Soft Touch probes. N2755A 01650-61607 16 ch 4 x 4 MSO cable kit for 3000, 4000, and 6000 X Series MSO. Includes 18 grabbers, 5 right angle grounds, and 5 ground extension leads 8 ch 2 x 4 MSO cable kit for 2000 X Series MSO. Includes 9 grabbers, 3 right angle grounds, and 3 ground extension leads 40-pin (F) to 40-pin (F) logic probe cable Characteristics for Keysight 01650‑61607 logic probe Input impedance Input capacitance The N2755A is an 8-channel MSO logic probe designed to work with the 2000 X-Series MSOs. 100 kΩ 12 pF N2756A 16-ch MSO cable kit 01650-61607 logic probe N2755A 8-ch MSO cable kit 21 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide Mixed Signal Oscilloscope Logic Probes (Continued) The InfiniiVision MSO digital channels were designed to be compatible with a wide variety of probing accessories developed over 20 years for logic analyzers. There is a good chance that the logic analyzer accessories you already own work with your MSO. With the addition of an optional 40-pin cable, 01650-61607, the MSO accepts numerous logic analyzer accessories: – E5346A 34-channel Mictor connector probe – E5385A 34-channel Samtec connector – E5383A 16-channel flying lead set – 01650-63203 16-channel termination adaptor (also available as a bundle of both the termination adapter and the 40-pin cable with PN 10085-68701) – E5404A 34-channel soft touch pro connectorless probe – E5394A 34-channel soft touch connectorless probe – E5396A 16-channel soft touch connectorless probe – Any other accessory that connects to a logic analyzer via a 40-pin cable For logic accessories of greater channel width than MSO digital channels (> 16 channels), there are two use models. – Route up to 16 signals to the probe and do not use the additional probe channels. – Route up to 32 signals to the probe and measure half of them at a time. Simply plug the 40-pin cable to the other side of the probe to see the other half of the signals. E5346A 34-channel Mictor connector probe E5396A 16-channel soft touch connectorless probe E5385A 34-channel Samtec connector probe 22 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide Clamp-on Current Probes – Up to 100 MHz bandwidth and 500 Arms current measurement range – Hybrid technology to measure ac and dc – Compatible with 1 MΩ scope input Accurate current measurements without breaking the circuit Compatible with any scope or voltage measuring instruments with BNC input, the 1146B and N2780B Series current probes offer accurate and reliable solutions for measuring dc and ac currents. The probes use a hybrid technology that includes a Hall effect sensor that senses the dc current, and a current transformer that senses the ac current, making it unnecessary to make an electrical connection to the circuit. 1146B 100 kHz current probe 1147B/N2893A 50-MHz/ 100-MHz current probe with AutoProbe interface N2780B/81B/82B/83B/83L 2‑MHz/10-MHz/50-MHz/ 100-MHz current probes The 1147B/N2893A is a wide bandwidth, dc to 50-MHz/100-MHz current probe. The probe offers flat frequency response across the entire dc to 50-MHz/100-MHz bandwidth, low noise (< –2.5 mArms) and low circuit insertion loss. The N2780B Series current probes are high bandwidth, active current probes, featuring flat bandwidth, low noise (2.5 mArms) and low circuit insertion loss. In conjunction with the power supply (model N2779A), these probes can be used with any oscilloscope having a highimpedance BNC input. The companion power supply N2779A (3 x 12 Vdc output) lets you connect up to any three N2780B83B current probes to a single power supply. The 1147B/N2893A probe is compatible with the AutoProbe interface, which completely configures the oscilloscope for the probe when used with the 3000 InfiniiVision Series scopes with AutoProbe interface. Probe power is provided by the scope, so there is no need for an external power supply. The N2893A uniquely provides auto demagnetization and offset elimination feature when used in conjunction with InfiniiVision or Infiniium scopes. The 1146B ac/dc current probe provides accurate display and measurement of currents from 100 mA to 100 Arms, dc to 100 kHz, without breaking into the circuit. A battery level indicator and overload indicator help ensure proper readings. It connects directly to the scope through a 2-m coaxial cable with an insulated BNC. The N2783L 80 MHz current probe offers a 5-m long cable, which allows you to reach DUTs over long distances very easily. Other than the bandwidth performance, the N2783A and N2783L have the same electrical performance. The N2783L also requires the N2779A power supply to power the probe. N2893A 100-MHz current probe with AutoProbe interface 1147B 50‑MHz current probe with AutoProbe interface 1146B 100-kHz current probe N2780B Series current probes with N2779A power supply 23 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide Clamp-on Current Probes (Continued) Characteristics of the 1146B current probe Bandwidth 1 Current range 1 Output signal dc to 100 kHz (–3 dB) 100 mV/A:100 mA to 10 A peak 10 mV/A:1 to 100 A peak 1000 mV peak max AC current accuracy 1 Range 100 mV/A (50 mA to 10 A peak) Accuracy 3% of reading ± 50 mA Range 10 mV/A (500 mA to 40 A peak) Accuracy 4% of reading ± 50 mA Range 10 mV/A (40 A to 100 A peak) Accuracy (40 A to 100 A peak) 15% max at 100 A Noise Range 10 mV/A: 480 μV Range 100 mV/A: 3 mV Insertion impedance 0.01 Ω (50/60 Hz) Maximum working 600 Vrms CAT II or voltage 300 Vrms CAT III Maximum common 600 Vrms CAT II or mode voltage 300 Vrms CAT III Influence of < 0.2 mA/A AC adjacent conductor Influence of < 0.2 mA/A AC conductor position Battery 9 V alkaline (NEDA 1604A, IEC 6LR61) Low battery Green LED on when ≤ 6.5 V Battery life 55 hours typical Note: Reference conditions 23 ± 5 °C, (73.4 ± 41 °C) 20 to 75% relative humidity, dc to 1 kHz, probe zeroed, 1-minute warmup, batteries at 9 V + 0.1 V, external magnetic field < 40 A/m, no dc component, no external current carrying conductor, 1 MΩ/100 pF load, conductor centered in jaw. 1. Characteristics marked with asterisks are specified performance. Others are typical characteristics. Characteristics of the 1147B/ N2893A current probe Bandwidth (–3 dB) Risetime Maximum current (continuous) Maximum peak current (noncontinuous) Output voltage rate Amplitude accuracy Noise dc to 50 MHz (1147B) dc to 100 MHz (N2893A) 7 ns or less (1147B), 3.5 ns or less (N2893A) 15 A peak, 15 A DC, 10 Arms (when two probes are used with InfiniiVision scope) 30A peak, 30 A DC, 24 Arms (when one probe is used with InfiniiVision 3000X, 5000/6000/7000 scope) 30 A peak (when two probes are used with InfiniiVision scope) 32 A peak (when one probe is used with InfiniiVision scope) 0.1 V/A ± 1% rdg, ± 10 mA (dc and 45 to 66 Hz, rated current) Equivalent to 2.5 mArms or less (for 20 MHz bandwidth measuring instrument) Temperature ± 2% or less (within a range coefficient for of 0 to 40 °C or 32 to sensitivity 104 °F) Effect of Equivalent to a external maximum of 20 mA (in a dc magnetic fields to 60 Hz, 400 A/m magnetic field) Maximum rated 3 VA (with rated current) power Maximum input 300 V CAT I voltage Diameter of 5 mm dia. (0.2 in dia.) measurable conductors Probe interface AutoProbe interface Cable lengths Sensor cable: Appox. 1.5 m (59.0n in) Power supply cable: Appox. 1 m (39.4 in) 2 Maximum number of probes supported Note: The above specifications are guaranteed at 23 ± 3 °C (or 73 ± 5 °F). Characteristics of N2780B Series current probes Bandwidth (–3 dB) dc to 2 MHz (N2780B) dc to 10 MHz (N2781B) dc to 50 MHz (N2782B) dc to 80 MHz (N2783L) dc to 100 MHz (N2783A) Maximum current 500 A (N2780B) (continuous) 150 A (N2781B) 30 A (N2782B/83B/83L) Maximum peak 700 A peak (N2780B) current (non300 A peak (N2781B) continuous) 50 A peak (N2782B/83B/83L) Maximum input 300 V CAT I voltage (N2782B/83B/83L) 300 V CAT III, 600 V CAT II (N2780B/81B) Output voltage rate 0.01 V/A (N2780B/81B) 0.1 V/A (N2782B/83B/83L) Amplitude accuracy ± 1.0 % rdg ± 500 mA (N2780B) ± 1.0 % rdg ± 100 mA (N2781B) ± 1.0 % rdg ± 10 mA (N2782B) ± 1.0 % rdg ± 10 mA (N2783B/83L) Ordering information for Keysight current probes 1146B 1147B N2893A N2780B N2781B N2782B N2783L N2783B N2779A 100-kHz current probe 50-MHz current probe with AutoProbe interface 100-MHz current probe with AutoProbe interface 2-MHz current probe 10-MHz current probe 50-MHz current probe 80-MHz current probe with 5-m long cable 100-MHz current probe 3-channel power supply for N2780B/81B/82B/83B/83L For more information about the N2780B Series current probes, refer to the Keysight N2780B Series current probe data sheet, literature number 5989-6432EN. 24 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide High-sensitivity Current Probes – Measure AC/DC currents as low as 50 µA – Ideal for capturing and analyzing low level current flow in the DUT to characterize sub-circuits or measure current consumption of batterypowered devices or integrated circuits – Simultaneous high- and low-gain views of the current waveform for more precise wide dynamic range measurement (with N2820A) Use an area-under-the-curve measurement (Charge) on InfiniiVision oscilloscopes to easily calculate the integrated current consumptions over time in Ah. The N2820A/21A high-sensitivity current probes are compatible with InfiniiVision 3000 X-, 4000 X- and 6000 X-Series oscilloscopes. As modern battery-powered devices and integrated circuits become more green and energy efficient, there is a growing need to make high-sensitivity, low-level current measurements to ensure the current consumption of these devices is in acceptable limits. The N2820A high-sensitivity probe is engineered to make high-dynamic-range, highsensitivity measurements to meet today’s challenging current measurement needs. The ultra-sensitive N2820A AC/DC current probe can support measurements from 50 µA to 5 A on Keysight oscilloscopes. The N2820A interface uses a make-before-break (MBB) connector, allowing you to quickly probe multiple locations on your DUT without having to solder or unsolder the leads. The N2820A 2-channel current probe connects to two oscilloscope channels to provide simultaneous low-and high-gain views for wider dynamic range measurement, while the N2821A 1-channel current probe provides one user-selectable view at a time. The N2820A 2-channel current probe connects to two oscilloscope channels to provide simultaneous low- and high-gain views for wider dynamic range measurement 25 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide High-sensitivity Current Probes (Continued) Probe characteristics and specification Bandwidth (–3 dB) Risetime (Tr = 0.35/bandwidth, 10 to 90%) Minimum measurable current 1 Maximum measurable current DC amplitude accuracy Gain 3 Max input voltage Output impedance Standard accessories Compatible InfiniiVision oscilloscopes Max number of probes supported by 3000 X-Series Max number of probes supported by 4000 X-Series Zoom-out channel: DC to 3 MHz Zoom-in channel: DC to 500 kHz Zoom-out channel: < 0.116 μs Zoom-in channel: < 0.7 μsec 250 μA (with N2822A 20 mΩ, 500 mW) 50 μA (with N2824A 100 mΩ, 500 mW) 5 mA (with N2825A user-defined 1 mΩ, 500 mW) 50 μA (with N2825A user-defined 1 kΩ, 500 mW) 5 A (with N2822A 20 mΩ, 500 mW) 2.2 A (with N2824A 100 mΩ, 500 mW) 5 A 2 (with N2825A user-defined 1 mΩ, 500 mW) 1.2 mA 2 (with N2825A user-defined 1 kΩ, 500 mW) ± 3% or 10 μA (whichever is greater) Zoom-in channel: 300 ± 3% Zoom-out channel: 1.97 ± 3% ± 12 V 1 MΩ 1 each 20 mΩ resistor sensor head 1 each 100 mΩ resistor sensor head 1 each user-defined resistor sensor head 5 each twisted leads (22 AWG) with sockets 5 each twisted leads (22 AWG) without sockets 5 each MBB headers 5 each MBB receptacles 1 each ground lead 1 each screw driver 1 each passive cable (with N2820A only) 1 each user guide manual (English) InfiniiVision 3000 X-Series (with software version 2.30 or higher) InfiniiVision 4000 X-Series (with software version 3.10 or higher) InfiniiVision 6000 X-Series (with software version 6.00 or higher) Two N2820A probes using both pods or two N2821A probes Two N2820A probes using both pods, four N2820A probes using only the primary pod, or four N2821A probes 1. Vsupply is equal to 5 V, solder attached. 2. Max current varies with max resistor power rating. The examples in the table assume 500 mW power rating. 3. Denotes warrantied specification after 20-minute warm up. All others entries in the table are characteristics. Ordering information for Keysight current probes Model numbers N2820A N2821A Replacement part numbers N2822A N2824A N2825A N2826A N2827A N2828A N2829A Descriptions High-sensitivity 2-ch current probe High-sensitivity 1-ch current probe 20 mΩ resistor tips 100 mΩ resistor tips User-defined resistor tips Replacement wires (15.5 cm, 22 AWG bare wires) (qty 5) Passive cable (for N2820A secondary channel) Replacement MBB (make before break) headers (qty 5) Replacement MBB (make before break) receptacles and 15.5 cm, AWG 22 socketed wires (qty 5 each) 26 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide Wedge Probe Adapters – Easy connection to surface mount ICs – Safe, with no chance of shorting – Mechanically non-invasive contact – 3-, 8-, and 16-signal versions – Supports 0.5 and 0.65‑mm – TQFP and PQFP packages Problem-free probing The Keysight wedge probe adapter eliminates many of the frustrations associated with probing surface mount components. If you have ever accidentally shorted IC pins together, experienced electrical and/or mechanical problems with soldering small wires onto leads, or gotten frustrated juggling multiple probes while you are trying to operate your scope, the Wedge was designed with you in mind. Make the inaccessible accessible When you use the Wedge, you do not have to worry about shorting IC pins together on a delicate component–or on an irreplaceable prototype. The Wedge is easy to insert and it stays put. There is no need to solder small wires onto leads. The Wedge is mechanically non-invasive, so you will not damage the legs of the IC. Instead, you will have easy access to hard-to-reach components. Electrical reliability The Wedge makes two contact points with each leg of the IC. This redundant physical connection increases the electrical reliability of the connection. The Wedge’s low capacitance and inductance provides superior performance to many other alternatives. The Wedge probe adapter connects directly to 1145A/1155A active probes and the dual lead adapter provided with the 1160A-65A passive probe family and N2877A/N2879A accessory kits for use with N287xA Series passive probes. IC clip kits Ordering information An inexpensive solution for probing fine-pitch ICs, the 10072A SMT kit includes 10 IC clips and 2 dual-lead adapters that connect the clips directly to 10070-family probes. The 10075A 0.5‑mm IC clip kit is ideal for connecting to ICs as fine as 0.5 mm. The clip body allows many clips to be mounted side-by-side. The kit includes four 0.5‑mm IC clips and two dual-lead adapters that connect the IC clips directly to 10070-family probes. Keysight Wedge electrical characteristics Operating voltage Operating current Capacitance between contacts Selfinductance Cross coupling Contact resistance < 40 Vdc + peak ac 0.5 A maximum 2 pF typical (all except Keysight‑E2643A/44A) 4.33 pF typical at 1 MHz (Keysight‑E2643A/44A) 15 nH typical (all except Keysight E2643A/44A) 37 nH typical at 1 MHz (Keysight E2642A/44A) –31 dB typical at 100 MHz (Keysight E2643A/44A) < 0.1 Ω E2613A E2614A E2643A E2615A E2616A E2644A 10072A 10075A 0.5 mm Wedge probe adapter, 3 signal, qty 1 0.5 mm Wedge probe adapter, 8 signal, qty 1 0.5 mm Wedge probe adapter, 16 signal, qty 1 0.65 mm Wedge probe adapter, 3 signal, qty 1 0.65 mm Wedge probe adapter, 8 signal, qty 1 0.65 mm Wedge probe adapter, 16 signal, qty 1 SMT kit for 10070 probe family 0.5 mm IC clip kit 27 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide Miscellaneous Accessories Testmobile Carrying cases Rackmount kit The sturdy Keysight 1180CZ Testmobile for use with 6000 Series oscilloscopes makes sharing your scope easy. Its large wheels make it easy to roll from place to place. For use with the Keysight 6000 Series scope, the 1180CZ Testmobile scope cart with the N2919A bracket provides convenient mobility and secure mounting of your scope. The Keysight N6457A soft carrying case makes transporting and shipping your 2000 X- and 3000 X-Series oscilloscope safe and simple. An oscilloscope and other accessories fit neatly inside the padded shell for shipment. For use with the 7000, 4000 X-, and 6000 X-Series, order N2733B soft carrying case. The Keysight N2916B rackmount kit positions your 5000 and 6000 Series scope in the center of the rack. Each kit includes a custom shelf with rails, six BNC pass-throughs and all necessary screws. For mounting the 7000 Series in the rack, order N2732A. For mounting all 2000 X- and 3000 X-Series in a rack, order N6456A. For mounting any 4000 X-Series in a rack, order N2763A. For mounting a 6000 X-Series in a rack, order the N2111A. Specifications for the Keysight Testmobiles 1180CZ Total load capacity Tilt tray Ordering information 59 kg (130 lbs) 1180CZ N2919A 45.7 cm wide x 45.7 cm deep (18 in wide x 18 in deep) N2760A soft carrying case for the 5000 Series Testmobile for 6000 Series Bracket for 1180CZ Testmobile and 6000 Series scope N2917B Hard carrying case for 5000 and 6000 Series N6457A Soft carrying case for 2000 X- and 3000 X-Series N2733B Soft carrying case for 7000, 4000 X- and 6000 X-Series N2760A Soft carrying case for 5000 Series N2916B Rackmount kit for 5000 and 6000 Series N2732A Rackmount kit for 7000 Series N6456A Rackmount kit for 2000 and 3000 X-Series N2763A Rackmount kit for 4000 X- Series N2111A Rack mount kit for 6000 X-Series N2733B soft carrying case for 7000, 4000 X-, and 6000 X-Series N2916B rackmount kit for 5000/6000 Series 28 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide Miscellaneous Accessories (Continued) Probe positioners – Easy-to-manipulate probe arms for hands-free browsing – One- or two-articulated arms with stable high-mass base (N2784A and N2785A) – Quick and stable XY positioning (N2786A) – Stable 3D probe positioning for hardto-reach XYZ access (N2787A) – Compatible with most scope probes – Applications: Hands-free browsing for electronic components on PC board Ordering information Product number N2784A 1 N2785A 1 N2786A N2787A Description 1-arm probe positioner 2-arm probe positioner 2-leg probe positioner 3D probe positioner 1. Includes 3x magnifying glass, arm strap, cable tie, probe rest, and manual. The N2784A and N2785A probe positioners provide quick and stable X-Y positioning for PC boards and devices that require hands-free probing. Unlike other probe positioners that require multiple adjustments to lock the probe holder into position, the N2784A and N2785A need only the “lift and drop” motion to put the probe in place. The weight stabilization technique used in these probe holders keeps constant pressure at the probing point so the probe tip stays in position even when the target board is bumped. N2784A one-arm probe positioner The N2786A is a low cost, easy-to-use X-Y axis probe holder for general purpose probing applications. The two-legged positioner is designed to be easy to use– the positioner itself has no controls to position it in place. The N2787A is a 3D probe positioner with a flexible, articulating arm that can be quickly positioned in a variety of configurations. For more information about Keysight’s probe positioners, refer to literature number 5989-9131EN. N2786A 2-leg probe positioner N2787A 3D probe positioner 29 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide N2744A T2A Probe Interface Adapter – Enables Tektronix TekProbeBNC level 2 probes to connect to Keysight’s AutoProbe interface on InfiniiVision 3000 X-, 4000 X-, 6000 X-, 5000, 6000, and 7000 oscilloscopes – An easy-to-use plug-on adapter to the Keysight oscilloscope’s AutoProbe interface – Provides necessary probe power, calibration, and offset control as needed to the attached TekProbe probe The N2744A T2A interface adapter enables selected TekProbe interface level 2 probes to be used with Keysight oscilloscopes with the AutoProbe interface. Existing TekProbe-BNC probe types can simply be plugged into the T2A adapter, which is then plugged directly into any AutoProbe input channel on an InfiniiVision or Infiniium oscilloscope. Select the probe model in the scope menu and the Keysight oscilloscope sets up the attenuation factor and the probe type automatically. The T2A interface adapter supplies the necessary probe power, calibration (for selected models only), and offset control as used by the connected TekProbe probe. The adapter is targeted for customers using both Tek active probes with TekProbe-BNC level 2 interfaces and Keysight oscilloscopes with the AutoProbe interface. Single-ended active probes P6243 P6245 P6205 P6241 P6249 Differential active probes P5205 or P5205A P5210 or P5210A P6246 P6247 P6248 Tek probe compatibility P6250 The N2744A T2A adapter supports only the probes listed with TekProbe interfaces. P6251 AC/DC current probe TCP202 50-MHz AC/DC current probe Single-ended active probe, 1 GHz, 10:1 without offset control Single-ended active probe, 1.5 GHz, 10:1 with offset control Single-ended active probe, 750 MHz, 10:1 without offset control Single-ended active probe, 4 GHz, 10:1 with offset control Single-ended active probe, 4 GHz, 5:1 with offset control Differential probe, 100 MHz, 50:1/500:1 with offset control Differential probe, 50 MHz, 100:1/1000:1 with offset control 400 MHz, 10:1/1:1 with offset control 1 GHz, 10:1/1:1 with offset control 1.5 GHz, 10:1/1:1 with offset control 500 MHz, 50:1/5:1 with offset control 1 GHz, 50:1/5:1 with offset control Keysight scope compatibility – Keysight InfiniiVision 6000 X-Series with software version 6.00 or higher – Keysight InfiniiVision 3000 X-/4000 X-Series with software version 1.10 or higher – Keysight InfiniiVision 5000, 6000, and 7000 Series and future revisions (except 6000 100-MHz) with software version 06.16 or higher Optical-to-Electrical Converters (works with InfiniiVision 5000, 6000 and 7000 with version 6.16 software only) P6701B 1 GHz optical-to-electrical converter with FC/PC connector P6703B 1.2 GHz optical-to-electrical converter with FC/PC connector P6711 250 MHz optical-to-electrical converter P6713 300 MHz optical-to-electrical converter Ordering information N2744A T2A probe interface adapter 30 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide Recommended Probes for Low-/Mid-speed Bus Measurements Applications LIN ARINC 425 CAN MIL-STD 1553 I²S (audio) I²C/SMbus RS232/UART RS422/485 FlexRay SPI MOST USB 2.0 Speed and signal type 10 kHz, single-ended 1000 kbps, differential 1 Mbps, differential 1 Mbps, differential ± 25 Vpp ~2.8 MHz, single-ended < 4 MHz, single-ended < 10 Mbps, single-ended 10 Mbps, differential 10 Mbps, differential 1 to 100 MHz, single-ended 150 Mbps, differential 480 Mbps, differential Recommended probe SE passive N2792A/N2818A N2792A/N2818A N2792A/N2818A SE passive SE passive SE passive N2792A/N2818A N2792A/N2818A SE passive or N2795A N2750A N2750A Required probe bandwidth > 100 MHz 200 MHz 200 MHz 200 MHz > 100 MHz > 100 MHz > 100 MHz 200 MHz 200 MHz > 100 MHz passive or 1 GHz active 1.5 GHz 1.5 GHz 31 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide Keysight Oscilloscopes Multiple form factors from 20 MHz to > 90 GHz | Industry leading specs | Powerful applications 32 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide www.axiestandard.org AdvancedTCA® Extensions for Instrumentation and Test (AXIe) is an open standard that extends the AdvancedTCA for general purpose and semiconductor test. Keysight is a founding member of the AXIe consortium. ATCA®, AdvancedTCA®, and the ATCA logo are registered US trademarks of the PCI Industrial Computer Manufacturers Group. www.lxistandard.org LAN eXtensions for Instruments puts the power of Ethernet and the Web inside your test systems. Keysight is a founding member of the LXI consortium. www.pxisa.org PCI eXtensions for Instrumentation (PXI) modular instrumentation delivers a rugged, PC-based high-performance measurement and automation system. 33 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Selection Guide From Hewlett-Packard through Agilent to Keysight For more than 75 years, we‘ve been helping you unlock measurement insights. Our unique combination of hardware, software and people can help you reach your next breakthrough. Unlocking measurement insights since 1939. 1939 THE FUTURE myKeysight www.keysight.com/find/mykeysight A personalized view into the information most relevant to you. Three-Year Warranty www.keysight.com/find/ThreeYearWarranty Keysight’s committed to superior product quality and lower total cost of ownership. Keysight is the only test and measurement company with three-year warranty standard on all instruments, worldwide. And, we provide a one-year warranty on many accessories, calibration devices, systems and custom products. Keysight Assurance Plans www.keysight.com/find/AssurancePlans Up to ten years of protection and no budgetary surprises to ensure your instruments are operating to specification, so you can rely on accurate measurements. Keysight Infoline www.keysight.com/find/service Keysight’s insight to best in class information management. Free access to your Keysight equipment company reports and e-library. Keysight Channel Partners www.keysight.com/find/channelpartners Get the best of both worlds: Keysight’s measurement expertise and product breadth, combined with channel partner convenience. For more information on Keysight Technologies’ products, applications or services, please contact your local Keysight office. The complete list is available at: www.keysight.com/find/contactus Americas Canada Brazil Mexico United States (877) 894 4414 55 11 3351 7010 001 800 254 2440 (800) 829 4444 Asia Pacific Australia China Hong Kong India Japan Korea Malaysia Singapore Taiwan Other AP Countries 1 800 629 485 800 810 0189 800 938 693 1 800 11 2626 0120 (421) 345 080 769 0800 1 800 888 848 1 800 375 8100 0800 047 866 (65) 6375 8100 Europe & Middle East Austria Belgium Finland France Germany Ireland Israel Italy Luxembourg Netherlands Russia Spain Sweden Switzerland United Kingdom 0800 001122 0800 58580 0800 523252 0805 980333 0800 6270999 1800 832700 1 809 343051 800 599100 +32 800 58580 0800 0233200 8800 5009286 800 000154 0200 882255 0800 805353 Opt. 1 (DE) Opt. 2 (FR) Opt. 3 (IT) 0800 0260637 For other unlisted countries: www.keysight.com/find/contactus (BP-02-10-16) DEKRA Certified ISO9001 Quality Management System TekProbe , TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. ® ® www.keysight.com/find/probes ® www.keysight.com/go/quality Keysight Technologies, Inc. DEKRA Certified ISO 9001:2015 Quality Management System This information is subject to change without notice. © Keysight Technologies, 2012 - 2016 Published in USA, April 18, 2016 5968-8153EN www.keysight.com
